[Ord. No. 6924 §§1—3(9-131), 2-22-1999]
A. 
The submission to the Planning and Zoning Commission shall consist of five (5) black or blue line prints on white background, and such other documents in five (5) copies as are necessary to meet the requirements of this Chapter.
B. 
The preliminary plat shall be clearly and legibly drawn. The size of the plat shall not be smaller than eight and one-half (8½) inches by eleven (11) inches. The plat of a subdivision containing six (6) acres or more shall be drawn at a scale of one (1) inch equals fifty (50) feet, unless otherwise determined by the Planning and Zoning Commission.
[Ord. No. 6924 §§1—3(9-132), 2-22-1999]
A. 
The preliminary plat shall contain the following information:
1. 
Proposed name of subdivision.
2. 
Name and address of owner of record.
3. 
Name and address of subdivider.
4. 
Date of survey, north point and graphic scale.
5. 
Preliminary engineering certificate.
6. 
Location and legal description, giving acreage.
7. 
Except boundary lines of the tract indicated by a heavy line, giving dimensions and angles.
8. 
Contour intervals to sea level datum, of not more than two (2) feet when the slope is less than four percent (4%) and not more than five (5) feet when the slope is greater than four percent (4%).
9. 
Natural features within and surrounding the proposed subdivision, including drainage channels, bodies of water, wooded areas and other significant features. On all watercourses leaving the tract, the direction of flow shall be indicated and for all water drainage courses entering the tract, the drainage area above the point of entry shall be noted.
10. 
Cultural features within and surrounding the proposed subdivision, including existing and platted streets, bridges, culverts, utility lines, pipelines, power transmission lines, all easements, park areas, structures, City and County lines, section lines and other significant information.
11. 
Names of streets within the immediate area of the proposed subdivision.
12. 
Names of recorded subdivisions abutting the proposed subdivision.
13. 
Zoning districts, if applicable.
14. 
Proposed layout, including lot lines with rough dimensions, lot number, block numbers, street and alley lines with proposed street names, right-of-way widths, sites reserved for parks, playgrounds, schools, etc., sites for non-public uses and building lines with dimensions.
[Ord. No. 6924 §§1—3(9-133), 2-22-1999]
A. 
The preliminary plat shall be accompanied by the following information:
1. 
A summary of the proposal, giving information as to the overall development plan with type of structure, number of dwelling units, types of business and industry, so that the effects of the development can be determined by the Planning and Zoning Commission.
2. 
Existing and proposed covenants and restrictions.
3. 
Source of water supply as approved by State Division of Health.
4. 
Provisions for sewage disposal, drainage and flood control as approved by State Water Pollution Board.
5. 
Letters or certificates of approval or disapproval from City, County or State agencies, as well as provisions for utility services, as applicable.
6. 
Typical cross sections of all streets and street construction plans. Centerline profiles of approximate street grades derived from office computations may be required by the Planning and Zoning Commission, if deemed advisable.
7. 
Such other information as the subdivider wishes to bring to the attention of the Planning and Zoning Commission.
[Ord. No. 6924 §§1—3(9-134), 2-22-1999]
A. 
The submission of final plats shall consist of the original drawing plus five (5) prints, plus other documents in five (5) copies as are necessary to meet the requirements of this Article and the requirements of State law. The subdivider shall also furnish the Planning and Zoning Commission with one (1) reproducible print of the final drawing showing the executed certificates, as specified in Section 410.230.
B. 
The final plat shall be clearly and legibly drawn in black ink on tracing cloth or paper vellum. The size of the plat shall not be larger than seventeen and one-half (17½) inches by twenty-three and one-quarter (23¼) inches, including margins, when the plat is drawn at a scale of one (1) inch equals one hundred (100) feet to the nearest one-tenth (0.1) foot, necessary internal angles, arcs and chords and tangent or radii of rounded corners.
C. 
The final plat shall conform to the preliminary plat, except for scale and it may constitute only that portion of the approved preliminary plat which the subdivider proposes to record and develop at any one time; provided, that such portion conforms to the requirements of this Chapter.
[Ord. No. 6924 §§1—3(9-135), 2-22-1999]
A. 
The final plat shall contain the following information:
1. 
Proposed name of subdivision.
2. 
Name and address of owner of record.
3. 
Name and address of subdivider.
4. 
Date of survey, north point and graphic scale.
5. 
Location and legal description, giving acreage.
6. 
Vicinity map.
7. 
Key map, when more than one (1) sheet is required to present plat.
8. 
Courses and distances to the two (2) nearest established section corners or bench marks or other recognized permanent monuments which shall accurately describe the location of the plat.
9. 
Exact boundary lines of the tract or other acceptable control traverse, giving dimensions to the nearest one-tenth (0.1) foot and angles to the nearest thirty (30) seconds, which shall be balanced and closed with an error of closure not to exceed one (1) to five (5) thousand. The type of closure shall be noted. Boundary lines shall be indicated by a heavy line.
10. 
Municipal, County or section lines accurately tied to the lines of the subdivision when such traverse or are reasonably close to the subdivision.
11. 
Names of recorded subdivisions abutting the subdivision.
12. 
Names of streets within the immediate area.
13. 
Street and alley and other right-of-way lines, with location and width, with street names indicated.
14. 
Street centerlines, showing angles of deflection, angles of intersection, radii, length of tangents and arcs and degree of curvature with basis of curve data.
15. 
Lot lines and dimensions to the nearest one-tenth (0.1) foot, necessary internal angles, arcs and chords and tangent or radii of rounded corners.
16. 
Building lines with dimensions.
17. 
When lots are located on a curve or when side lot lines are at angles other than ninety degrees (90°), the lot width at the building line shall be shown when required by the Planning and Zoning Commission.
18. 
Lot and block numbers.
19. 
Easements and public service or utility right-of-way lines giving dimensions, location and purpose.
20. 
Accurate outlines and description of any areas to be dedicated or reserved for public use or acquisition with the purposes indicated thereon; and of any areas to be reserved by deed covenant for common uses of all property owners.
21. 
Accurate location and description of all monuments.
22. 
Certificate of engineering accuracy.
23. 
Certificate of owner.
24. 
Certificate of final plat approval.
25. 
Certificate of recording.
26. 
All other information required by State law.
[Ord. No. 6924 §§1—3(9-136), 2-22-1999]
A. 
The final plat shall be accompanied by the following information and documents unless shown on the plat itself:
1. 
Bill of assurance including, but not limited to, the following provisions: offering dedications of streets and alleys, parks and other public lands; establishing easements, setting forth privileges and conditions pertaining thereto; setting forth the restrictions and covenants of the subdivision; and setting forth procedures by which amendments to the bill of assurance can be made. Such bill of assurance shall contain reference to the approval of the final plat.
2. 
Certification of approval of water supply and sanitary sewage disposal and utility services by the appropriate agencies.
[Ord. No. 6924 §§1—3(9-137), 2-22-1999]
A. 
Preliminary Engineering Certificate.
I hereby certify that this proposed preliminary plat correctly represents a survey completed by me on_____________, 20_____________, of property shown and described hereon; and described monument placed on the property are correctly described and located in accordance with the established and accepted monuments in the vicinity.
(Signed)
  Date of Execution
  Name Registered Professional Engineer No.____,
  Missouri
B. 
Certificate Of Preliminary Plat Approval.
All requirements of the Webb City subdivision rules and regulations relative to the preparation and submittal of a preliminary plat having been fulfilled, approval of this plat is hereby granted, subject to further provisions of said rules and regulations.
This Certificate shall expire __________________ (Date)
(Signed)
  Date of Execution
  Name Chairman, Planning and Zoning Commission
[Ord. No. 6924 §§1—3(9-138), 2-22-1999]
A. 
Each final plat submitted to the Planning and Zoning Commission for approval shall carry the following certificates printed thereon substantially as follows:
1. 
Certificate of owner(s).
We, the undersigned, owners of the real estate shown and described herein, do hereby certify that we have laid off, platted and subdivided, and do hereby lay off, plat and subdivide, said real estate in accordance with the plat.
(Signed)
  Date of Execution
  Name
  Address
2. 
Certificate of recording.
This document, number _______________ filed for record _______________, 20_____, at _________ o'clock __.M. , recorded _______________ 20_____, in Plat Book __________, Page ______.
For Bill of Assurance, see Deed Record Book _______ Page _____.
3. 
Certificate of engineering accuracy.
I hereby certify that this plat represents a survey and a plan made by me; that all monuments shown hereon actually exist and their location, size, type and material are correctly shown; and that all engineering requirements of the City subdivision rules and regulations have been fully complied with.
(Signed)
  Date of Execution
  Name Registered Professional Engineer No.____,
  Missouri
4. 
The certificate of final plat approval shall be printed on both the final plat and bill of assurance substantially as follows:
Certificate Of Final Plat Approval
Pursuant to the Webb City subdivision rules and regulations, this document was given final approval by the Webb City Planning and Zoning Commission at the meeting held _____________, 20______. All of the conditions of approval having been completed, this document is hereby accepted and this certificate executed under the authority of said rules and regulations.
(Signed)
  Date of Execution
  Name Chairman, Planning and Zoning Commission
Approved by the City Council of the City of Webb City, Missouri, pursuant to Section 89.400 RSMo., as amended, on the ____ day of____________________, 20___.
(Seal)
City Clerk