The sketch plan initially submitted to the Planning
Board shall be based on Village tax map information or some other
similarly accurate base map at a scale, preferably not less than 200
feet to the inch, to enable the entire tract to be shown on one sheet.
The sketch plan proposal shall be submitted showing the following
information:
A.
The name of the owner and of all adjoining property
owners as disclosed by the most recent Village tax records.
B.
The location of that portion which is to be subdivided
in relation to the entire parcel and the distance to the nearest existing
street intersection.
C.
The tax map sheet, block and lot numbers.
D.
All the utilities available and all streets which
are either proposed, mapped or built.
E.
The proposed pattern of lots, including lot width
and depth, street layout and systems of drainage, sewerage and water
supply within the subdivided area.
F.
All existing restrictions on the use of land, including
easements, covenants or zoning lines.
A.
The application shall consist of a final plat, labeled
as such. The size of the sheets shall be 24 inches by 36 inches, including
a margin of one-inch outside ruled border line on three sides and
two inches along the left side of the twenty-four-inch side for binding.
The plat shall be submitted at a scale of not more than 100 feet to
the inch.
B.
The final plat shall include the following:
(1)
The proposed subdivision name and the name of the
Village and Onondaga County.
(2)
The name and address of the record owner, subdivider
and licensed professional engineer, surveyor or architect who prepared
the plat.
(3)
The date, true North point and scale.
(4)
The names of all subdivisions and owners of record
of all property immediately adjacent to the boundaries of the subdivision.
(5)
A copy of such covenants or deed restrictions as are
intended to cover all or part of the subdivision.
(6)
An actual field survey of the boundary lines of the
subdivision, giving complete descriptive data, by bearing and distances,
made and certified to by a licensed land surveyor. The corners of
the subdivision shall also be located on the ground and marked by
monuments as approved by the Village Engineer and shall be referenced
and shown on the final plat.
(7)
Typical cross sections of the proposed grading and
topographic conditions.
(8)
A statement signed by a licensed engineer that all
on-site sanitation and water supply facilities have been designed
to meet the minimum specifications of the Onondaga County Department
of Health and the Onondaga County Water Authority.
(a)
A stormwater pollution prevention plan (SWPPP) consistent with the requirements of Chapter 50, Stormwater Management and Erosion and Sediment Control. The SWPPP shall meet the performance and design criteria and standards in Chapter 50, and the approved minor subdivision final plat shall be consistent with the provisions of Chapter 50.
[Added 12-18-2007 by L.L. No. 2-2007]
(9)
Such other information, modifications or additions
as may be required by the Planning Board.
C.
The final plat to be filed or recorded with the Onondaga
County Clerk shall be printed upon linen or canvas-backed paper or
be clearly drawn in waterproof ink upon tracing cloth.
A.
The subdivider shall present to the Planning Board
a preliminary plat, labeled as such. The size of the sheets shall
be 24 inches by 36 inches, including a margin of one-inch outside
ruled border lines on three sides and a two-inch border along the
left side of the twenty-four-inch side for binding. The preliminary
plat shall be submitted at a scale of not more than 100 feet to the
inch, showing or accompanied by the following information:
(1)
The proposed subdivision name and the name of the
Village and Onondaga County.
(2)
The name and address of the record owner, subdivider
and designer of the preliminary plat.
(3)
The date, true North point and scale.
(4)
The names of all subdivisions and owners of record
of all property immediately adjacent to the boundaries of the subdivision.
(5)
The location of boundary lines, existing easements,
buildings, watercourses and other essential features.
(6)
An actual field survey of the boundary lines of the
subdivision, giving complete descriptive data, by bearing and distances,
made and certified to by a licensed land surveyor. The corners of
the subdivision shall also be located on the ground and marked by
monuments as approved by the Village Engineer and shall be referenced
and shown on the final plat.
(7)
The location of any existing sewers, water mains,
other utilities, culverts and drains on the property to be subdivided.
(8)
The location, names and widths of existing and proposed
streets, highways and easements and the location of building lines,
alleys, parks and other public open spaces and similar facts regarding
adjacent property.
(9)
Any changes in the use, height, area and density restrictions
or other regulations under the Zoning Code applicable to the area
to be subdivided and any boundaries of such districts affecting the
tract; all parcels of land proposed to be dedicated to public use
and the conditions of such dedication.
(10)
The width and location of any street or other
public ways or places shown upon the Official Map within the area
to be subdivided, and the width, location, grades and street profiles
of all streets or other public ways proposed by the subdivider.
(11)
Typical cross sections of the proposed grading
and roadways or sidewalks and topographic conditions.
(12)
Connections with she existing sanitary sewerage
system or alternative means of treatment and disposal in conformity
with applicable laws, rules and regulations.
(13)
Provisions for collecting and discharging surface
and subsurface drainage.
(14)
Preliminary designs of any bridges or culverts
which may be required.
(15)
The proposed lot lines with approximate dimensions
and suggested location of buildings.
(16)
The proposed location of sidewalks; the location
and type of streetlights, street trees, curbs and gutters; the location,
size and type of water mains, sanitary and storm sewers and storm
drains; the material, width and depth of pavement base course and
subbase course (if required); and the location of manholes and basins
and underground conduits.
(17)
Boundaries of proposed permanent easements over
or under private property.
(18)
A sketch of the prospective future street system
of any unsubmitted part of the subdivider's entire holdings. The street
system of the unsubmitted part will be considered in the light of
adjustments and connections with the street system of the submitted
part.
(19)
A stormwater pollution prevention plan (SWPPP) consistent with the requirements of Chapter 50, Stormwater Management and Erosion and Sediment Control. The SWPPP shall meet the performance and design criteria and standards in Chapter 50, and the approved major subdivision preliminary plat shall be consistent with the provisions of Chapter 50.
[Added 12-18-2007 by L.L. No. 2-2007]
B.
The information set forth above is required for the
purpose of complying with §§ 7-728 through 7-738 of
the Village Law and other applicable laws and regulations. Due care
in the preparation of this material will expedite the process of passing
upon the suitability of the preliminary plat.
A.
The final plat submitted for approval and subsequent
recording with the Onondaga County Clerk shall be clearly and legibly
drawn in the form prescribed for the preliminary plat and shall be
printed upon linen or canvas-backed paper or be clearly drawn in waterproof
ink upon tracing cloth.
B.
The final plat shall contain all information required
on the preliminary plat, as well as all modifications or additions
required by the Planning Board.
C.
The final plat shall also contain the following:
(1)
The name, license number and seal of the licensed
professional engineer, architect or land surveyor who prepared the
final plat.
(2)
The length of all straight lines and the deflection
angles, radii, lengths and central angles of all curves. Tangent distances
and tangent bearings shall be given for each street. All dimensions
and angles of the lines of each lot shall also be given. All dimensions
shall be shown in feet and decimals of a foot.
(3)
The final plat shall also show, by proper designation
thereon, all public open spaces for which deeds of cession are included
and those spaces to which title is reserved by the subdivider. For
any of the latter, there shall be submitted with the final plat copies
of agreements or other documents showing the manner in which such
areas are to be maintained and the provisions made therefor.
(4)
A copy of such covenants or deed restrictions as are
intended to cover all or part of the subdivision.
(5)
Before final approval of the final plat, there shall
be filed with the Planning Board a certificate of the Village Engineer
as to the completion of all improvements required by the Planning
Board to his satisfaction in accordance with standards and specifications
prescribed by the Village Engineer. For any required improvements
not so completed, there shall be submitted with the final plat a certificate
of the Village Attorney as to the sufficiency of the bond or approved
substitute offered in lieu thereof.
(6)
Lots and blocks within a subdivision shall be numbered
and lettered in alphabetical order in accordance with the prevailing
Village practice.
(7)
Permanent reference monuments shall be shown thus,
"X." They shall be constructed in accordance with specifications of
the Village Engineer and, when referenced to the state system of plan
coordinates, shall also conform to the requirements of the New York
State Department of Transportation. They shall be placed as required
by the Village Engineer and their location noted and referenced upon
the final plat.
(8)
A statement signed by a licensed engineer that all
on-site sanitation and water supply facilities have been designed
to meet the minimum specifications of the Onondaga County Department
of Health and the Onondaga County Water Authority.
(a)
A stormwater pollution prevention plan (SWPPP) consistent with the requirements of Chapter 50, Stormwater Management and Erosion and Sediment Control, and with the terms of preliminary plat approval. The SWPPP shall meet the performance and design criteria and standards in Chapter 50, and the approved major subdivision final plat shall be consistent with the provisions of Chapter 50.
[Added 12-18-2007 by L.L. No. 2-2007]
(9)
Such other information, modifications or additions
as may be required by the Planning Board.
