This article requires the retrofitting of existing storm drain
inlets which are in direct contact with repaving, repairing, reconstruction,
or resurfacing or alterations of facilities on private property, to
prevent the discharge of solids and floatables (such as plastic bottles,
cans, food wrappers and other litter) to the municipal separate storm
sewer system of the Borough of Hasbrouck so as to protect public health,
safety and welfare, and to prescribe penalties for the failure to
comply.
As used in this article, the following terms shall have the
meanings indicated:
PERSON
Any individual, corporation, company, partnership, firm,
association, or political subdivision of this State subject to municipal
jurisdiction.
STORM DRAIN INLET
An opening in a storm drain used to collect stormwater runoff
and includes, but is not limited to, a grate inlet, curb-opening inlet,
slotted inlet, and combination inlet.
WATERS OF THE STATE
The ocean and its estuaries, all springs, streams and bodies
of surface or ground water, whether natural or artificial, within
the boundaries of the State of New Jersey or subject to its jurisdiction.
No person in control of private property (except a residential
lot with one single-family house) shall authorize the repaving, repairing
(excluding the repair of individual potholes), resurfacing (including
top coating or chip sealing with asphalt emulsion or a thin base of
hot bitumen), reconstructing or altering any surface that is in direct
contact with an existing storm drain inlet on that property unless
the storm drain inlet either:
A. Already meets the design standard below to control passage of solid
and floatable materials; or
B. Is retrofitted or replaced to meet the standard in §
235-5.4 below prior to the completion of the project.
Storm drain inlets identified in §
235-5.2 above shall comply with the following standard to control passage of solid and floatable materials through storm drain inlets. For purposes of this paragraph, "solid and floatable materials" means sediment, debris, trash, and other floating, suspended, or settleable solids. For exemptions to this standard see §
235-5.4C below.
A. Design engineers shall use either of the following grates whenever
they use a grate in pavement or another ground surface to collect
stormwater from that surface into a storm drain or surface water body
under that grate:
(1)
The New Jersey Department of Transportation (NJDOT) bicycle
safe grate, which is described in Chapter 2.4 of the NJDOT Bicycle
Compatible Roadways and Bikeways Planning and Design Guidelines (April
1996); or
(2)
A different grate, if each individual clear space in that grate
has an area of no more than 7.0 square inches, or is no greater than
0.5 inches across the smallest dimension.
(3)
Examples of grates subject to this standard include grates in
grate inlets, the grate portion (non-curb-opening portion) of combination
inlets, grates on storm sewer manholes, ditch grates, trench grates,
and grates of spacer bars in slotted drains. Examples of ground surfaces
include surfaces of roads (including bridges), driveways, parking
areas, bikeways, plazas, sidewalks, lawns, fields, open channels,
and stormwater basin floors.
B. Whenever design engineers use a curb-opening inlet, the clear space
in that curb opening (or each individual clear space, if the curb
opening has two or more clear spaces) shall have an area of no more
than 7.0 square inches, or be no greater than 2.0 inches across the
smallest dimension.
C. This standard does not apply:
(1)
Where the municipal engineer agrees that this standard would
cause inadequate hydraulic performance that could not practicably
be overcome by using additional or larger storm drain inlets that
meet these standards;
(2)
Where flows are conveyed through any device (e.g., end of pipe
netting facility, manufactured treatment device, or a catch basin
hood) that is designed, at a minimum, to prevent delivery of all solid
and floatable materials that could not pass through one of the following:
(a)
A rectangular space 4 5/8 inches long and 1 1/2 inches
wide (this option does not apply for outfall netting facilities);
or
(b)
A bar screen having a bar spacing of 0.5 inches.
(3)
Where flows are conveyed through a trash rack that has parallel
bars with one-inch spacing between the bars; or
(4)
Where the New Jersey Department of Environmental Protection
determines, pursuant to the New Jersey Register of Historic Places
Rules at N.J.A.C. 7:4-7.2(c), that action to meet this standard is
an undertaking that constitutes an encroachment or will damage or
destroy the New Jersey Register listed historic property.
Any person, firm or entity who or which is found to be in violation of the provisions of this ordinance shall be subject to a fine or penalty as provided in Chapter
204 of this Code for each storm drain inlet that is not retrofitted to meet the design standard.