All preliminary plats initially submitted to the Planning Board
shall be based on Tax Map information or some other similarly accurate
base map at a scale, preferably not less than 200 feet to the inch,
to enable the entire tract to be shown on one sheet and prepared by
a licensed surveyor. The preliminary plat shall be submitted showing
the following information:
A.
The location of that portion which is to be subdivided in relation
to the entire tract, and the distance to the nearest existing street
intersection.
B.
All existing structures, wooded areas, streams and other significant
physical features within the portion to be subdivided and within 200
feet thereof. If topographic conditions are significant, contours
shall also be indicated at intervals of not more than 10 feet, or
as determined by the Planning Board.
[Amended 5-14-2007 by L.L. No. 5-2007]
C.
The name of the owner and of all adjoining property owners as disclosed
by the most recent municipal tax records.
D.
The Tax Map sheet, block and lot numbers, if available.
E.
All the utilities available and all streets which are either proposed,
mapped or built.
F.
The proposed pattern of lots (including lot width and depth), street layout, recreation areas, systems of drainage, sewerage and water supply [See § 215-22A(3).] within the subdivided area.
G.
All existing restrictions on the use of land, including easements,
covenants or zoning lines.
H.
For conservation subdivisions, to the extent not provided for above,
all existing features (as defined in this chapter) and primary and
secondary conservation areas.
A.
In addition to the information required in § 215-21, minor subdivision applications shall also include the following information:
(1)
A copy of such covenants or deed restrictions as are intended to
cover all or part of the tract.
(2)
An actual field survey of the boundary lines of the tract, giving
complete descriptive data by bearings and distances, made and certified
to by a licensed land surveyor. The corners of the tract shall also
be located on the ground and marked by monuments as approved by the
Town Engineer and shall be referenced and shown on the plat.
(3)
All on-site sanitation and water supply facilities shall be designed
to meet the minimum specifications of the State Board of Health, and
a note to this effect shall be stated on the plat and signed by a
licensed engineer.
(4)
Proposed subdivision name, name of the Town and county in which it
is located.
(5)
The date, North point, map scale, name and address of record owner
and subdivider.
(6)
If topographic conditions are significant, contours shall also be
indicated at intervals of not more than 10 feet, or as determined
by the Planning Board.
[Amended 5-14-2007 by L.L. No. 5-2007]
B.
The plat to be filed with the County Clerk shall be clearly drawn
and printed upon a Mylar or paper format that is reproducible. The
size of the sheet shall be 24 inches by 30 inches.
The following documents shall be submitted for conditional approval:
A.
Seven copies of the preliminary plat, prepared at a scale of not
more than 100 feet but preferably not less than 50 feet to the inch,
showing:
[Amended 5-14-2007 by L.L. No. 5-2007]
(1)
Proposed subdivision name, name of the Town and county in which it
is located, date, true North point, scale, and name and address of
the record owner, subdivider and engineer or surveyor, including license
number and seal.
(2)
The name of all subdivisions immediately adjacent and the name of
the owners of record of all adjacent property.
(3)
The zoning district, including the exact boundary lines of the district, if more than one district, and any proposed changes in the zoning district lines and/or Chapter 250, Zoning, applicable to the area to be subdivided.
(4)
All parcels of land proposed to be dedicated to public use and the
conditions of such dedication.
(5)
The location of existing property lines, easements, buildings, watercourses,
marshes, rock outcrops, wooded areas, single trees with a diameter
of eight inches or more as measured three feet above the base of the
trunk and other significant existing features for the proposed subdivision
and adjacent property.
(6)
The location of existing sewers, water mains, culverts and drains
on the property, with pipe sizes, grades and direction of flow.
(7)
Contours at intervals of two feet or as required by the Planning
Board, including elevations on existing roads, and approximate grading
plan if natural contours are to be changed more than two feet.
(8)
The width and location of any streets or public ways or places shown
on the Official Map,[1] if such exists, or the Comprehensive Plan, within the
area to be subdivided, and the width, location, grades and street
profiles of all streets or public ways proposed by the developer.
[1]
Editor's Note: Said map is on file in the Town offices.
(9)
The approximate location and size of all proposed waterlines, valves,
hydrants and sewer lines and fire alarm boxes; connection to existing
lines or alternate means of water supply or sewage disposal and treatment
as provided in the Public Health Law; profiles of all proposed waterlines
and sewer lines.
(10)
A storm drainage plan indicating the approximate location and
size of proposed lines and their profiles, connection to existing
lines or alternate means of disposal.
(11)
Plans and cross sections showing the proposed location and type
of sidewalks, streetlighting standards, street trees, curbs, water
mains, sanitary sewers and storm drains, and the size and type thereof;
the character, width and depth of pavements and subbase; the location
of manholes, basins and underground conduits.
(12)
Preliminary designs of any bridges or culverts which may be
required.
(13)
The proposed lot lines, with approximate dimensions and area
of each lot.
(14)
Where the topography is such as to make difficult the inclusion
of any of the required facilities within the public areas as laid
out, the preliminary plat shall show the boundaries of proposed permanent
easements over or under private property, which permanent easements
shall not be less than 20 feet in width and which shall provide satisfactory
access to an existing public highway or other public highway or public
open space shown on the Subdivision Map or the Official Map.[2]
[2]
Editor's Note: Said maps are on file in the Town offices.
(15)
An actual field survey of the boundary lines of the tract, giving
complete descriptive data by bearings and distances, made and certified
to by a licensed land surveyor. The corners of the tract shall also
be located on the ground and marked by substantial monuments of such
size and type as approved by the Town Engineer and shall be referenced
and shown on the plat.
B.
If the application covers only a part of the subdivider's entire
holding, a map of the entire tract, drawn at a scale of not less than
400 feet to the inch, showing an outline of the platted area with
its proposed streets and indication of the probable future street
system with its grades and drainage in the remaining portion of the
tract and the probable future drainage layout of the entire tract,
shall be submitted. The part of the subdivider's entire holding
submitted shall be considered in the light of the entire holding.
C.
A copy of such covenants or deed restrictions as are intended to
cover all or part of the tract shall be submitted.
A.
The following documents shall be submitted for plat approval. The
plat to be filed with the County Clerk shall be printed upon a Mylar
or paper format that is reproducible. The size of the sheets shall
be 24 inches by 30 inches, including a margin for binding of two inches
outside of the border along the left side and a margin of one inch
outside of the border along the remaining sides. The plat shall be
drawn at a scale of no more than 100 feet to the inch and oriented
with the North point at the top of the map. When more than one sheet
is required, an additional index sheet of the same size shall be filed
showing to scale the entire subdivision with lot and block numbers
clearly legible.
B.
The plat shall show:
(1)
Proposed subdivision name or identifying title and the name of the
Town and county in which the subdivision is located, the name and
address of the record owner and subdivider, and the name, license
number and seal of the licensed land surveyor.
(2)
Street lines, pedestrianways, lots, reservations, easements and areas
to be dedicated to public use.
(3)
Sufficient data acceptable to the Town Engineer to determine readily
the location, bearing and length of every street line, lot line and
boundary line and to reproduce such lines upon the ground. Where applicable,
these should be referenced to monuments included in the state system
of plane coordinates and, in any event, should be tied to reference
points previously established by a public authority.
(4)
The length and bearing of all straight lines, radii, length of curves
and central angles of all curves and tangent bearings shall be given
for each street. All dimensions and angles of the lines of each lot
shall also be given. All dimensions shall be shown in feet and decimals
of a foot. The plat shall show the boundaries of the property location,
graphic scale and true North point.
C.
The plat shall also show, by proper designation thereon, all public
open spaces for which deeds are included and those spaces title to
which is reserved by the developer. For any of the latter, there shall
be submitted with the subdivision plat copies of agreements or other
documents showing the manner in which such areas are to be maintained
and the provisions made therefor.
D.
All offers of cession and covenants governing the maintenance of
unceded open space shall bear the certificate of approval of the Town
Attorney as to their legal sufficiency.
E.
Lots and blocks within a subdivision shall be numbered and lettered
in alphabetical order in accordance with the prevailing Town practice.
F.
Permanent reference monuments shall be shown and shall be constructed
in accordance with specifications of the Town Engineer. When referenced
to the state system of plane coordinates, they shall also conform
to the requirements of the State Department of Transportation. They
shall be placed as required by the Town Engineer and their location
noted and referenced upon the plat.
G.
All lot corner markers shall be permanently located satisfactorily
to the Town Engineer, at least 3/4 inch (if metal) in diameter and
at least 24 inches in length, and located in the ground to existing
grade.
H.
Monuments of a type approved by the Town Engineer shall be set at
all corners and angle points of the boundaries of the original tract
to be subdivided and at all street intersections, angle points in
street lines, points of curve and such intermediate points as shall
be required by the Town Engineer.
I.
A map shall be submitted, to the satisfaction of the Planning Board, indicating the location of monuments marking all underground utilities as actually installed. If the subdivider completes all required improvements according to Article II, § 215-9A(2), then said map shall be submitted prior to final approval of the subdivision plat. However, if the subdivider elects to provide a bond or certified check for all required improvements as specified in Article II, § 215-9A(1), such bond shall not be released until such map is submitted in a form satisfactory to the Planning Board.