[Ord. 1005, 5/23/2011]
This Part contains the best practices, technical and engineering
requirements for design and construction of required improvements,
utilities, grading and erosion control, survey detail, stormwater
drainage, paving, curbing, pathways and sidewalks, emergency access,
bridges, signage and markings, lighting, solid waste storage, street
names, and easements.
[Ord. 1005, 5/23/2011]
1.Â
All adjacent structures and areas disturbed or damaged during construction
shall be properly repaired, restored, or replaced to the satisfaction
of the Borough by the party causing the damage.
2.Â
All trees, roots, stumps, brush, down timber, wood, rubbish and any
objectionable material shall be removed from the full legal right-of-way,
or as approved by the Borough Engineer. Efforts shall be made during
construction of streets to preserve any vegetation specifically identified
in the landscaping plan for preservation.
3.Â
Paving. The pavement of all streets and all commercial, industrial,
and multifamily parking areas and driveways into and out of parking
areas shall be installed as shown on the final plan and in accordance
with the standards set forth in the Borough of Hatboro Specifications
and Design Standards, incorporated herein by reference and as may
be amended from time to time by Resolution of Borough Council.
4.Â
Radii of Pavement and Right-of-Way at Intersections. Street intersections
shall be in accordance with the Borough of Hatboro Specifications
and Design Standards, incorporated herein by reference and as may
be amended from time to time by Resolution of Borough Council.
5.Â
All radii specified herein must be increased if large trucks, fire
trucks, or other emergency vehicles would have difficulty with ingress
or egress as determined by the Borough Fire Marshal and Borough Engineer.
6.Â
Sidewalk Construction and Driveway Crossing. Sidewalk construction,
including standards established by the Americans with Disabilities
Act, and driveway crossing specifications, shall be in accordance
with the Borough of Hatboro Specifications and Design Standards, incorporated
herein by reference and as may be amended from time to time by Resolution
of Borough Council.
7.Â
Bituminous Pathway (Bike/Hiking Path). Pathways shall be in accordance
with the Borough of Hatboro Specifications and Design Standards, incorporated
herein by reference and as may be amended from time to time by Resolution
of Borough Council.
8.Â
Driveway Apron. The concrete apron in the driveway area shall be
in accordance with the Borough of Hatboro Specifications and Design
Standards, incorporated herein by reference and as may be amended
from time to time by Resolution of Borough Council.
9.Â
Driveways normally used by not more than 25 vehicles per day shall
comply with the standards contained in 67 Pa. Code, Chapter 441, "Access
to and Occupancy of Highways by Driveways and Local Roads," § 441.8(i)(5),
"Grade Requirements Where Curbs and Sidewalks are Present." Driveways
normally used by more than 25 vehicles per day shall comply with standards
appropriate for their anticipated traffic volumes in conformance with
accepted engineering standards and practices. The Borough Engineer
shall be consulted for accepted engineering standards and practices.
11.Â
All driveways shall be provided with a stopping area within which
the grade shall not exceed 4%. The stopping area shall be measured
as follows:
12.Â
Maximum grade requirements shall not be waived unless extremely difficult
circumstances exist and cannot be mitigated by alternative locations,
designs, or lotting, in which case a safe, practical alternative may
be permitted by the Hatboro Borough Council, upon recommendation of
the Borough Engineer.
13.Â
Curb Construction. All curbing shall be constructed be in accordance
with the Borough of Hatboro Specifications and Design Standards, incorporated
herein by reference and as may be amended from time to time by Resolution
of Borough Council.
[Ord. 1005, 5/23/2011]
1.Â
General Drainage Provisions.
A.Â
Blocks and Lots. Blocks and lots shall be graded to secure proper
drainage away from buildings and to allow the collection of stormwater
in catch basins. Minimum 2% slopes away from structures shall be required.
Slopes of less than 2% must have the approval of the Borough Engineer.
B.Â
Design. All drainage provisions shall be of such design as to carry surface water to the nearest practical storm drain, detention basin, retention basin or natural watercourse. Where drainage swales are used, they shall not be less than 1% grade. The swales shall be sodded or planted as required and shall be of such shape, size, and slope to conform with specifications of the Borough Engineer. Stormwater management facilities must address volume reduction, groundwater recharge, peak rate control, and water quality. Designs must incorporate features that provide aesthetic and wildlife benefits while controlling vectors and other nuisances, including mosquitoes. Stormwater facilities shall be designed based on accepted standards such as those provided in the Borough Stormwater Management Ordinance [Chapter 23], as amended, and the Pennsylvania Stormwater Best Management Practices Manual, as amended.
C.Â
Construction. The developer shall construct and/or install such drainage
structures and/or pipes which are necessary to prevent erosion damage
and to satisfactorily carry off such surface waters to the nearest
practical storm drain or natural watercourse, in accordance with current
Pennsylvania Erosion Control and Sedimentation Regulations.
E.Â
Natural Watercourses. Drainage easements shall be required along
natural watercourses to a minimum width of 20 feet. Where conditions
warrant, such as in floodplains, additional width shall be required
to convey a one-hundred-year design storm. Staged discharge or water
surface profile studies for the design storm may be required to establish
high water elevations.
F.Â
Easements and Dedications. Where stormwater or surface water will
be gathered within the subdivision or land development and discharged
or drained in volume over lands within or beyond the boundaries of
the subdivision or land development, the subdivider, developer, or
builder shall reserve or obtain easements over all lands affected.
The easements shall be adequate for such discharge or drainage and
for carrying off of such water and for the maintenance, repair, and
reconstruction of the same, including the right of passage over including
vehicles, machinery, and other equipment for such purposes, and which
shall be of sufficient width for such passage and work. The subdivider,
developer, or builder shall convey, at no cost to the Borough, easements
to the Borough on demand, at the completion and stabilization of all
improvements.
2.Â
Hydrologic Calculations.
A.Â
Calculations to determine potential runoff shall include hydrologic
analysis indicating peak discharge rate and volume of runoff for both
predevelopment and post-development conditions.
B.Â
Design Methodology. The methods of calculation used to determine
peak rate and volume of runoff for design of stormwater management
facilities shall be in accordance with the Borough of Hatboro Specifications
and Design Standards, incorporated herein by reference and as may
be amended from time to time by Resolution of Borough Council.
3.Â
Hydraulic Calculations. All calculations shall be in accordance with
the Borough of Hatboro Specifications and Design Standards, incorporated
herein by reference and as may be amended from time to time by Resolution
of Borough Council.
4.Â
Storm Sewers and Drainageways.
A.Â
General Provisions. All storm drains and drainage facilities such
as gutters, catch basins, bridges, inlets, and culverts shall be installed
and the land graded for adequate drainage as shown on the grading
plan submitted and approved with the final plan. Construction of these
facilities shall generally conform with PennDOT Specifications Pub.
408, latest edition.
B.Â
When Required. Storm drains and appurtenances shall be required to
be constructed by the subdivider to take surface water from the bottom
of vertical grades to lead water away from springs, and to avoid excessive
use of cross gutters at street intersections and elsewhere.
(1)Â
Open watercourses will be permitted where they exist naturally
and where, in the opinion of the Borough Engineer, they will not interfere
with public convenience or safety, but in fact will provide comparable
or superior drainage capabilities of piped drainage. Necessary stream
corridor improvements including rock stabilization and gabions where
necessary shall be performed.
(2)Â
When submitting a plan for approval involving the construction
of storm drainage facilities the designer's computations shall
be submitted in duplicate to facilitate the checking of design.
(3)Â
Design of storm drainage facilities shall be completed in accordance
with accepted engineering practices subject to approval by the Borough
Engineer.
C.Â
Location. Wherever practical, storm sewers shall be located within
the right-of-way of the street. They shall be protected by a cover
of at least 18 inches. Trench restoration shall conform to the construction
standards of this Part.
D.Â
Size and Grade. Storm sewers shall be adequate for the anticipated runoff when the area is fully developed as permitted by zoning, and capable of carrying design storms per Subsection 2 and the Borough of Hatboro Specifications and Design Standards, incorporated herein by reference and as may be amended from time to time by Resolution of Borough Council. They shall have a minimum internal diameter of 15 inches and a minimum grade of 0.5% unless otherwise approved by the Borough Engineer. Maximum internal pipe diameter shall be 60 inches. Special box culverts or open channels shall be used when a sixty-inch pipe is not capable of carrying the design storm. Open channels will not be permitted where a conduit equal to or less than 60 inches in diameter can be constructed.
E.Â
Storm Drainage Pipe Materials. All storm drainage pipes up to but
not including 42 inches in equivalent diameter shall be constructed
in accordance with the Borough of Hatboro Specifications and Design
Standards, incorporated herein by reference and as may be amended
from time to time by Resolution of Borough Council.
F.Â
All storm drainage pipe and/or culverts 42 inches in equivalent diameter
and above shall be constructed in accordance with the Borough of Hatboro
Specifications and Design Standards, incorporated herein by reference
and as may be amended from time to time by Resolution of Borough Council.
G.Â
Change in Direction. Special curved storm drain sections may be used
where abrupt changes are made in alignment in lieu of constructing
manholes if the circumstances so warrant as approved by the Borough
Engineer.
H.Â
Manholes. Manholes shall be constructed at all changes in horizontal
or vertical alignment; shall be spaced not more than 300 feet apart
on pipe of 24 inches internal diameter or less, and not more than
450 feet apart where larger sizes are installed. Inlets may be substituted
for manholes where they will serve a useful purpose. Manhole frames
and covers shall be good quality cast iron; covers shall be marked
"STORM" and have a minimum weight of 220 pounds.
I.Â
Inlets. Inlets spacing shall be arranged in compliance with PennDOT
Design Manual No. 2 as last revised. Inlet structures shall be designed
in compliance with PennDOT RC-34 as last revised. All inlets within
road rights-of-way shall be equipped with PennDOT bicycle safe grates.
J.Â
Castings. Manhole and inlet castings, together with their covers
or gratings shall conform to PennDOT or Borough Standards, as may
be in effect at the time the design of the sewer is submitted.
K.Â
Unnatural Drainage. Wherever construction stops or concentrates the
natural flow of storm drainage in such a way to affect adjoining properties,
approval of the owners shall be obtained in writing and a copy filed
with the Borough. Approval of plans by the Borough does not authorize
or sanction drainage affecting adjoining properties.
L.Â
Drainage from Nonnatural Sources. Water originating from other than
natural sources, such as air conditioning units, sump pumps, or other
dry weather flow, wherever practicable, shall be discharged into natural
watercourses on the property. The discharge of water under the sidewalk
through the curb into the gutter is prohibited.
M.Â
Design Criteria.
(1)Â
Minimum internal pipe diameter shall be 15 inches.
(2)Â
Open channels shall have a parabolic or trapezoidal cross-section
in compliance with accepted engineering practices.
(3)Â
Permissible channel velocities, slopes, and cover shall be in
accordance with the DEP Erosion and Sediment Pollution Control Program
Manual.
(4)Â
Existing stream channels shall be maintained in their natural
state. Only under unusual circumstances will it be permitted to line,
straighten, or relocate an existing stream, with approval of DEP and
the Montgomery County Conservation District.
(5)Â
Acceptable energy dissipation devices shall be installed to
bring discharge velocities down to limits specified in the DEP Erosion
and Sediment Pollution Control Program Manual. Rip-rapping and/or
gabions may be required by the Borough Engineer where erosion potential
is great.
(6)Â
Where open-ended influent pipes cannot be avoided, safety facilities
shall be constructed, acceptable to the Borough Engineer.
(7)Â
Storm sewers and culverts shall be sized, based on the design
storm, to provide a minimum one-foot of freeboard at inlets, manholes,
and embankments.
5.Â
Stormwater Detention.
A.Â
Stormwater detention facilities will be required if one of the following
conditions is present:
(1)Â
Runoff from the development would exceed the capacity of downstream
stormwater facilities.
(2)Â
Runoff from the development would increase the peak runoff by
one cubic foot per second (CFS) or more from the existing conditions.
One single-family dwelling not requiring subdivision is exempt from
this requirement.
(3)Â
Runoff from a proposed parking facility or building would increase
the peak runoff from the existing condition.
B.Â
The design criteria for the stormwater detention facility shall be
agreed upon by the Borough Engineer. Developers are encouraged to
investigate all measures to reduce and detain water, for discharge
at a delayed rate or ground water recharge. All reasonable methods
will be considered.
6.Â
Basins or Other Management Facilities.
A.Â
General Provisions.
(1)Â
The design of all stormwater basins must be approved by the
Borough Engineer based upon their effectiveness for achieving stormwater
control objectives, water quality enhancement, groundwater recharge,
ease of maintenance, safety considerations, and conformance to landscape
and surrounding uses and activities.
(2)Â
Basins shall be installed prior to any earth moving in the areas
that drain into them. The phasing of their construction shall be noted
on the plan.
(3)Â
Where basins are required by Borough, adequate maintenance guarantees,
indemnification, insurance, and security shall be provided by the
applicant and approved by the Borough.
(4)Â
Where feasible, basins shall be developed jointly by abutting
landowners, or regionally by several developing landowners.
(5)Â
If a basin is to remain in private ownership, the applicant
shall assure proper maintenance in the form of a recorded deed restrictions,
bonds, or escrows, as approved by the Borough. The Borough has the
right to enter the lot to perform any required maintenance that has
not been performed or carried out in a timely manner by the lot owner.
The lot owner shall be liable for the cost of any maintenance which
is performed by the Borough, the Borough shall place a lien on the
property for all costs if the owner refuses to pay them.
(6)Â
Developers are encouraged to use best management practices (BMPs), if appropriate, to provide for additional water quality improvement and groundwater recharge. The methods and design criteria of stormwater controls or BMPs that may be used are described in the Borough Stormwater Management Ordinance [Chapter 23], as amended, and the "Pennsylvania Stormwater Best Management Practices Manual," December 2006, as amended.
(7)Â
A dam safety permit under 25 Pa. Code, Chapter 105, as issued
by the Department of Environmental Protection is required for all
basins that have dams on a natural watercourse where:
(8)Â
A dam safety permit under 25 Pa. Code, Chapter 105, as issued
by the DEP is required for basins not on a natural drainage course
where the greatest depth at the upstream toe of the dam at maximum
storage exceeds 15 feet or the impounding storage capacity at a maximum
storage elevation exceeds 50 acre-feet.
B.Â
Facility Design.
(1)Â
Basins shall be designed based upon the appropriate hydrologic
and hydraulic calculations which have been reviewed and approved by
the Borough Engineer. Basin storage capacity must be sufficient to
meet the requirements of this chapter.
(2)Â
Basins shall incorporate curvilinear reflective of surrounding
topography.
(3)Â
Minimum grades of stormwater basins shall be 2%. Grades of less
than 2% may be permitted when designed to convey water as approved
by the Borough Engineer. The maximum basin side slopes shall be three
to one.
(4)Â
The sizing and scale of the basin shall be compatible with other
elements of the site.
C.Â
Structural Improvements.
(1)Â
Outlet works and emergency spillways shall be sized to cause
detention of and passage of design inflow so as to maintain a two-foot
freeboard for storms up to a twenty-five-year, twenty-four-hour design
storm and a one-foot freeboard for storms up to the one-hundred-year,
twenty-four-hour storm.
(2)Â
Emergency spillways, where considered necessary by the Borough
Engineer, shall be sized and located to permit the safe passage of
stormwater flows from a one-hundred-year storm. The maximum velocities
in vegetated spillways excavated in undisturbed soil shall be checked
based upon the velocity of peak flow in the emergency spillway during
an assumed clogged primary outlet condition. Where maximum velocities
exceed design standards contained in the Erosion and Sediment Pollution
Control Manual, suitable lining shall be provided. All emergency spillways
placed on fill materials shall be lined. Lining for emergency spillways
shall incorporate native colors and materials where possible including
mono slab revetments, grass pavers and native stone.
(3)Â
Inlet Structures. The invert of the inlet pipe into a basin
shall be six inches above the basin floor or lining so that the pipe
can adequately drain after rain storms. Inlets shall discharge into
areas of the basin that slope toward the outlet structure. Inlet and
outlet structures shall be located at a maximum distance from each
other in order to promote water quality benefits. The Borough Engineer
may require a rock filter or rock filled gabion for entrapping sediments
carried in stormwater if sufficient separation of inlet and outlet
structure cannot be achieved.
(4)Â
Energy Dissipators. Devices to dissipate or spread stormwater
flow shall be installed at points where pipes or drainageways drain
into or from a basin. Energy dissipators shall comply with criteria
in Hydraulic Engineering Circular No. 15, Design for Stable Channels
with Flexible Linings, published by the Federal Highway Administration,
or the DEP Erosion and Sediment Pollution Control Program Manual.
(5)Â
Outlet Structures. To minimize clogging and to facilitate cleaning,
outlet pipes shall have an internal diameter of at least 18 inches
and a minimum grade of 1%. Anti-seep collars shall be located on all
outlet pipes. All principal outlet structures shall be built with
reinforced concrete with watertight construction joints. The developer
shall consider the use of architecturally treated concrete, stucco,
painted surface or stone facade treatment for enhancing the outlet
structure. Outlet pipes shall be constructed of reinforced concrete
with rubber gaskets in conformance with AASHTO M170, M198 and M207.
Child proof trash racks or anti-vortex devices shall be constructed
at all outlets and designed to facilitate cleaning and avoid clogging
caused by debris.
(6)Â
Stabilization. Prior stabilization, structures including stilling
basins, energy dissipators, and channel lining shall be constructed
at the outlets of all basins and emergency spillways. The stabilization
structures shall control water to avoid erosion, reduce velocities
of released water and direct water so that it does not interfere with
downstream activities.
(7)Â
Wet Basins. Existing ponds or permanent pool basins can be used
provided that they meet the following criteria:
(a)Â
The minimum permanent pool level shall be maintained to allow
sufficient depth throughout the year to reduce the growth of unwanted
vegetation and mosquitoes.
(b)Â
The pond must be of sufficient size to allow the appropriate
aquatic community needed to maintain a healthy pond ecology.
(c)Â
An outlet structure shall be designed to allow complete drainage
of the pond for maintenance.
(d)Â
The applicant shall submit wet basin planting schedule and method
for mosquito control.
The design of a detention facility with a permanent pool shall
include the determination of the proposed site's ability to support
a viable permanent pool. The design shall take into account for such
factors as the required rate and quality of dry weather inflow, the
quality of stormwater inflow, seasonal and longer term variations
in groundwater table, and effects of suspected pollutant loadings.
|
(8)Â
Basins with Gabion Dams. Gabion outlet control structures for
stormwater basins shall be filled with rocks six inches to eight inches
in diameter. Outlet flow through the gabions shall be calculated by
the following equation:
Q = (0.40 x h x 2)/L
|
Where:
| ||||
Q
|
=
|
Flow in cubic feet per second (CFS)
| ||
h
|
=
|
Height of ponding in basin (feet)
| ||
w
|
=
|
Width of stone structure (feet)
| ||
L
|
=
|
Average structure thickness (top of berm + bottom of berm)/2
|
(9)Â
Underground Basins. Underground stormwater detention systems
can be used where sufficient space is not available for above-ground
systems or where underground storage systems are recharging groundwater.
(10)Â
Developers are encouraged to use best management practices (BMPs), if appropriate, to provide for additional water quality improvement and groundwater recharge. The methods and design criteria of stormwater controls or BMPs that may be used are described in the Borough Stormwater Management Ordinance [Chapter 23], as amended, and the "Pennsylvania Stormwater Best Management Practices Manual," December 2006, as amended. In evaluating potential stormwater BMPs, the order of preference shall be as follows:
7.Â
Design Submission.
A.Â
All plans showing the proposed storm sewer construction must be accompanied
by a complete design prepared by a registered engineer.
B.Â
When subdivisions or land developments are submitted to the Borough
Engineer for approval in sections, a complete storm sewer design for
the proposed subdivision and land development shall be submitted.
The proposed design must include the entire tract and not a portion.
C.Â
If only a section of a subdivision or land development is contemplated
for construction, the applicant's engineer shall show how he
proposes to handle stormwater from this section in order to prevent
damage to adjacent properties. If temporary construction is required,
the applicant's engineer shall include such structures in the
plan submitted.
D.Â
In the event such temporary measures cannot ensure protection to
adjacent properties, then the main outfall line of the storm sewer
shall be included as part of the construction for the proposed section.
[Ord. 1005, 5/23/2011]
1.Â
Widths and locations of easements and rights-of-way shall be determined
by the Borough Engineer or the appropriate Authority or utility company
for all utilities, including stormwater facilities, and shall be governed
by the requirements herein.
A.Â
General Standards.
(1)Â
Easements and required front, side or rear yards may co-occupy
the same land.
(2)Â
Nothing shall be permitted to be placed, planted, set or put
within the areas of an easement unless it is a portable or removable
object. The area shall be kept as lawn.
(3)Â
The owner of any lot, upon written request by the Borough and
at the owner's sole expense, shall remove anything placed, planted,
set or put, (with or without knowledge of these regulations) within
the area of any easement.
(4)Â
To the fullest extent possible, easements shall be adjacent
to rear or side lot lines, and occupying only a portion of one lot
(not centered on two lots).
B.Â
No right-of-way or easement for any purpose whatsoever shall be recited
or described in any deed unless the same has been shown on the approved
plan. Any error found in a deed shall be immediately corrected and
re-recorded in the Montgomery County Office of the Recorder of Deeds,
at the sole expense of the subdivider or developer.
C.Â
Utility Easements. A minimum width of 20 feet shall be provided for
common utilities and drainage when provided in undedicated land for
one use. Multiple utility uses within one easement require additional
easement width.
D.Â
Public Utilities. All water, sewer and gas mains and other underground
facilities shall be installed prior to street paving at locations
approved by the Borough Engineer.
E.Â
Underground Utilities. All water, sewer and gas mains shall be installed
underground. All electric, telephone and communication services, both
main and service lines, shall be provided by underground cables, installed
in accordance with the prevailing standards and practices of the utility
or other companies providing such services, except where it is demonstrated
to the satisfaction of Borough Council that underground installations
herein required are not feasible because of physical conditions of
the lands involved. All main underground cables which are within the
right-of-way of a street shall be located as specified by the utility
company, subject to approval by Borough Council, upon recommendation
of the Borough Engineer.
(1)Â
In order to promote and facilitate the underground installation
of utility distribution lines, a letter of endorsement shall be required
from the suppliers of utility service (not limited to electrical,
telephone, or cable television) of the developer's choice wherein
the applicant acknowledges that underground utilities are feasible
and shall be consummated as part of the improvement plan.
(2)Â
A statement relative to the intent of the developer to provide
underground utility service shall be placed on the final plan requisite
to final approval of the plan.
(3)Â
The provisions in this chapter shall not be construed as to
limit or interfere with the construction, installation, operation
and maintenance of public utility structures or facilities which may
hereafter be located within public easements or rights-of-way designated
for such purposes.
(4)Â
Lighting is to be located as required by ordinance. Power source
for such standards shall be placed underground as required.
(5)Â
Along arterial and collector streets, all new electrical service
shall be placed underground.
[Ord. 1005, 5/23/2011]
1.Â
Any new lot or principal building shall be connected to the public
sanitary sewage system.
2.Â
Sewage Facilities Design. The design and installation of sewage facilities
shall be done in accordance with applicable DEP requirements, applicable
public sanitary sewage authority requirements, applicable utility
owner requirements, and applicable Borough requirements.
[Ord. 1005, 5/23/2011]
1.Â
The subdivider or developer shall provide public water service to
each dwelling and principal building lot in a subdivision or land
development.
2.Â
Fire hydrants shall be located at accessible points throughout the
subdivision when centralized water supply is available, and shall
be located in accordance with the Borough Engineer, Borough Fire Marshal,
and municipal authority or water company. Hydrants shall be located
at each street intersection and at intermediate points as approved
by the Borough Engineer and Borough Fire Marshal. Generally hydrant
spacing may range from 350 feet to 600 feet depending upon the area
being served. The type and methods of construction to be employed
in the installation of fire hydrants shall be in accordance with current
regulations of the water supplier.
3.Â
Public Water Supply Facilities Design. The design for public water
supply facilities shall be in accordance with the DEP Water Supply
Manual.
[Ord. 1005, 5/23/2011]
1.Â
Each subdivision and land development shall comply with erosion and sediment control regulations of DEP, the Montgomery County Conservation District, and the Borough Stormwater Management Ordinance [Chapter 23], as amended.
A.Â
General. For qualifying tracts, no changes shall be made in the contour
of the land; no grading, excavating, removal or destruction of the
topsoil, trees or other vegetative cover of the land shall be commenced
until such time that a plan for minimizing erosion and sedimentation
has been approved by the Montgomery County Conservation District.
(1)Â
No subdivision or land development plan shall be approved unless: (a) there has been a plan approved by Borough Council that provides for minimizing erosion and sedimentation consistent with this section, and an improvement bond or other acceptable securities are deposited with the Borough. The form of an escrow guarantee which will ensure installation and completion of the required improvements shall be of the form specified in Part 5; or, (b) there has been a determination by the Montgomery County Conservation District that a plan for minimizing erosion and sedimentation is not necessary.
(2)Â
Borough Council, in its consideration of any plan of subdivision
and land development shall condition its approval upon the execution
of measures designed to prevent accelerated soil erosion and resulting
sedimentation, as required by DEP. All applicable regulations and
permit requirements of said Department as stipulated in its Soil Erosion
and Sedimentation Pollution Control Manual shall be followed by all
parties engaged in earth-moving activities.
B.Â
Performance Principles.
(1)Â
Any effective methods of minimizing erosion and sedimentation
can be included in the plan. Any questionable method shall be discussed
with the Borough Engineer prior to submission.
(2)Â
No unfiltered stormwater coming from an area which has been
disturbed shall be permitted onto an adjacent tract or discharge into
any water body.
C.Â
Responsibility.
(1)Â
Whenever sedimentation is caused by stripping vegetation, regrading
or other development activity, it shall be the responsibility of the
person, corporation or other entity causing such sedimentation to
remove it from all adjoining surfaces, drainage systems and watercourses
and to repair any damage at his expense as quickly as possible.
(2)Â
It is the responsibility of any person, corporation, or other
entity doing any act on or across a stream, watercourse or swale or
upon the floodplain or right-of-way thereof, to maintain, as nearly
as possible, in its present state the stream, watercourse, swale,
floodplain or right-of-way during the activity and to return it to
its original or equal condition after such activity is completed.
(3)Â
No person, corporation, or other entity shall block, impede
the flow of, alter, construct any structure, or deposit any material
or thing, or commit any act which will affect normal or flood flow
in any stream or watercourse without having obtained prior approval
from the Borough or DEP, whichever is applicable.
D.Â
Compliance with Regulations and Procedures.
(1)Â
Final plans for minimizing erosion and sedimentation as approved will be incorporated into the agreement and bond requirements as required under Part 5 of this chapter.
(2)Â
The approval of plans and specifications for the control of
erosion and sedimentation shall be concurrent with the approval of
the final plans of subdivision or land development, and become a part
thereof.
(3)Â
At the time that a building permit is applied for, a review
shall be conducted by the Borough Engineer to ensure conformance with
the plan as approved. During the construction, further consultative
technical assistance will be furnished, if necessary, by the Borough
Engineer and the Montgomery County Conservation District. During this
development phase, the Borough Engineer shall inspect the development
site and enforce compliance with the approved plans.
(4)Â
Permission for clearing and grading prior to recording of plans
or receipt of final plan approval may be obtained under temporary
permits or other conditions satisfactory to the Borough, at the applicant's
risk.
[Ord. 1005, 5/23/2011]
1.Â
Bridges and culverts shall be designed to meet current PennDOT standards
to support expected loads and to pass design stormwater flows. They
shall be constructed to the full width of the planned cartway. Allowance
for sidewalk must also be made, if required by the Borough.
2.Â
Where county-owned roads or bridges are involved, the County Engineer
must review and approve all proposals.
3.Â
It is unlawful to construct any dam or other water obstruction, or
to make any change in or addition to, any existing water obstruction,
or in any manner change or diminish the course, current, or cross-section
of any stream or body of water, without first having made written
application to and obtained a permit or consent in writing from DEP.
4.Â
The following information is required: drawings to include location
plan; cross-section of present bridge if one exists; profile of stream
for a reasonable distance above and below bridge site, showing slopes
of bed, normal water surface and flood water surface. If the bridge
is on a skew, give the angle of the center line of the bridge with
the direction of the line of flow. In addition, the following information
is required for new bridge construction: the total drainage area above
the bridge site; description of watershed; length of stream from source
to bridge site and to the mouth; character of stream bed and banks;
extent and depth of overflow during floods; effect of previous floods
upon bridges, their span and clearance; and whether bridge will be
within backwater influence of parent stream.
5.Â
A complete set of structural computations and drawings shall be submitted
with plans involving construction of bridges and culverts.
[Ord. 1005, 5/23/2011]
1.Â
Permanent monuments shall be indicated on the record plan. All monuments
shall be constructed of precast concrete or durable stone with metal
insert(s), and be four inches square with at least 20 inches extending
below ground level, or an alternate design approved by Borough Council.
Street right-of-way reference monuments shall be located on the right-of-way
lines at corners, angle points, beginning and end of curves, and as
otherwise required by the Borough Engineer for all new and existing
streets. They shall be placed after a new street and/or lot grading
has been completed. The center line of all new streets shall be marked
with spikes (P.K. nails) and referenced to permanent monuments or
structures. Certified copies of this reference information shall be
given to both the Borough Engineer and the Borough Office. When final
lot grading has been completed and before the issuance of occupancy
permits, permanent monuments shall be set by the subdivider, developer,
or builder, at all lot corners and angle points, and at all street
intersections and intermediate points as may be required.
2.Â
Lot Pin Requirements. All lots upon which construction is planned shall be temporarily staked or pinned, or permanently monumented and certified to such by a registered surveyor for the owner, subdivider, builder, or developer, before issuance of a building permit. A signed certificate of compliance must be submitted with a building permit application. Temporary stakes or pins with a surveyor's ribbon attached may be acceptable on existing lots where construction of an accessory building or an addition to the primary structure is proposed, only if construction is begun within 30 days of the certificate of compliance date. Temporary stakes or pins shall remain in place until witnessed and accepted by the Borough Building Inspector. Prior to final approval of a new subdivision plan, all new lot corner markers shall be marked with a minimum 5/8 inch diameter metal pin extending at least 24 inches into the ground and at least one inch revealed above the ground surface, or an equivalent metal marker, approved by the Borough Engineer. Upon completion of construction and final grading, pins shall be replaced with permanent monuments as described in Subsection 1.
3.Â
Original Monuments. In situations where they may be of legal or historical
importance, the original monuments and marks must not be destroyed,
defaced, hidden, or possible confused by creating new monuments and
marks unless absolutely necessary, e.g., the originals are decayed,
destroyed, or unsafe. In some cases, to be determined by the Borough
Engineer, new monuments shall be set as a reference or witness to
the original monument to avoid disturbing the original. When in the
opinion of the Borough Engineer, the angle point falls in a location
that is not appropriate to set a concrete monument, a written request
for a waiver shall be submitted for consideration by Borough Council.
4.Â
Bench Marks. The Borough elevations are based on the USGS datum.
Location and elevation is available to all engineers and surveyors
upon request to the Borough Engineer's Office. All contours and
elevations shown on the plan must be based on this system.
[Ord. 1005, 5/23/2011]
1.Â
Minimum cartway width shall be 10 feet.
2.Â
When paved, pavement shall conform to the Borough of Hatboro Specifications
and Design Standards, incorporated herein by reference and as may
be amended from time to time by Resolution of Borough Council.
3.Â
When not paved, the cartway shall be constructed of crushed stone
of appropriate size, depth, and compaction to support the largest
generally serving fire trucks under all weather conditions. Placed
on top of the six inches of crushed stone shall be an interlinked
porous pavement constructed of fiber reinforced polyethylene or concrete
grass pavers. All void areas shall be filled with topsoil and seeded
with an appropriate grass mix.
4.Â
Markings or appropriate form of identification shall be placed at
the entrance to the emergency accessway. If necessary, break away
bollards shall be installed at each end of the emergency accessway.
5.Â
Emergency accessways shall be maintained through properly recorded
easements or deed restrictions which at a minimum prohibit the planting
of any vegetation except grass within the accessway.
[Ord. 1005, 5/23/2011]
1.Â
A.Â
The applicant shall provide and install street lights in locations
determined to be necessary by the Borough. The Borough may also require
that street lights be provided and installed by the applicant along
private streets.
B.Â
The design of the street light fixtures and poles shall be subject
to approval by the Borough. Where a predominant design of luminaries
and poles has been established, the Borough may require that such
design be used in new lights.
C.Â
Lighting shall be designed in accordance with standards developed
by the electric utility provider. The Borough may require that lighting
meet standards recommended in the IESNA Lighting Handbook. Construction
of highway lighting shall be in conformance with PennDOT Specifications
Publication 408, most recent edition.
2.Â
Outdoor Lighting.
A.Â
Permanent outdoor lighting is required in places where public health,
safety and welfare are potential concerns. The outdoor lighting section
shall protect drivers and pedestrians from the glare of non-vehicular
light sources that shine into their eyes and thereby impair safe traverse,
protect neighbors and the night sky from nuisance glare and stray
light from poorly aimed, placed, applied, maintained or shielded light
sources.
B.Â
The requirements herein apply where outdoor lighting is required
by Borough ordinance, is otherwise required by the Borough, or is
proposed by the applicant. The requirements contained herein also
apply to sign, architectural, and landscape lighting. The requirements
herein do not apply to streetlights and traffic lights located in
the public right-of-way and owned by the Borough of Hatboro.
3.Â
Plan Submission.
A.Â
Lighting plans shall be submitted for review and approval of any
lighting installation in connection with a land development application
for any use identified in this section.
B.Â
Lighting plans shall include the following:
(1)Â
A site plan, complete with all structures, parking spaces, building
entrances, traffic areas (both vehicular and pedestrian), vegetation
that might interfere with lighting, and adjacent use(s) that might
be adversely impacted by the lighting, and containing a layout of
all proposed fixtures by location and type.
(2)Â
Description of the proposed equipment shall be included, including
fixture catalog cuts, photometrics, glare reduction devices, lamps
and mounting heights.
(3)Â
When requested by Borough Council, the applicant shall also
submit a visual impact plan that demonstrates appropriate steps have
been taken to mitigate on-site and off-site glare, including, but
not limited to, a plot plan with a matrix of the calculated footcandles
with measurements 10 feet into the neighboring properties, including
those on the opposite side of a public right-of-way or public roadway,
at five feet above ground.
C.Â
Notification must be sent to the Borough Engineer before any post-approval
alterations to lighting plans or intended substitutions for approved
lighting equipment are made. Post-approval alterations or intended
substitutions to the approved lighting plan must meet the requirements
of the originally approved plan.
4.Â
Design Standards.
A.Â
All lighting fixtures for off-street parking areas, off-street loading
areas, driveways and for safety of persons and property must meet
IESNA full cutoff.
B.Â
All fixtures for pedestrian areas and walkways must meet IESNA full
cutoff.
C.Â
In no event shall light fixtures exceed 15 feet in height, including
the mounting base.
[Amended by Ord. 1032, 5/23/2016]
5.Â
Performance Standards.
A.Â
All light fixtures shall contain lenses that focus light directly
beneath the light fixture and shall not permit direct glare into nearby
public or private properties.
[Amended by Ord. 1032, 5/23/2016]
B.Â
Illumination trespass standards from one property to another shall
be as follows:
[Amended by Ord. 1032, 5/23/2016]
(1)Â
In no case shall spill-over illumination more than 0.5 footcandle
at ground level exist on any nonresidentially zoned or used property
when measured, line of sight, at the property line of the aggrieved
property.
(2)Â
In no case shall spill-over illumination more than 0.1 footcandle
at ground level exist on any residentially zoned or used property
when measured, line of sight, at the property line of the aggrieved
property.
C.Â
Architectural lighting, as defined by this section, shall be aimed
or directed so as to preclude light projection beyond the immediate
object or objects intended to be illuminated. All such lighting shall
be extinguished between the hours of 10:00 p.m. and 6:00 a.m.
D.Â
Glare control shall be accomplished primarily through the proper
selection and application of lighting equipment. Only after those
means have been exhausted shall vegetation, fences and similar screening
methods be considered acceptable for reducing glare.
6.Â
Enforcement and Compliance.
A.Â
The landowner is responsible if found to be noncompliant to the lighting
plan approved by the Borough Council. The Borough may conduct a post-installation
inspection to verify compliance to the approved plan. After installation,
the Borough, by way of an authorized enforcement officer, may require
the landowner, at the landowner's expense, to make adjustments,
remedial measures, or other means to comply with the approved lighting
plan.
B.Â
Notwithstanding the installation date or pre-existing conditions
of a lighting fixture or arrangement, if the Borough determines that
the standards set forth are not met, the Borough, by way of an authorized
enforcement officer, may require the landowner, at the landowner's
expense, to make adjustments, remedial measures, or other means to
comply with the lighting standards.
C.Â
Notwithstanding the above requirements of this section, if at any
time the Borough deems a lighting fixture or arrangement to be a potential
safety hazard or nuisance, it may, at the landowner's expense,
require the landowner to make adjustments, remedial measures, or other
means to mitigate or prevent the potential hazard or nuisance.
D.Â
The measurement of the amount of illuminance, in footcandles, shall
be at the spot where the lighting fixture or arrangement is causing
the potential nuisance.
E.Â
The Borough reserves the right to conduct post-construction inspections
to confirm all outdoor lighting fixtures and arrangements, including
architectural lighting, comply with the ordinance standards.
[Ord. 1005, 5/23/2011]
1.Â
Street Signs. The developer shall erect at every intersection a street
sign or street signs having thereon the names of the intersecting
streets. At intersections where streets cross, there shall be at least
two such street signs and at the intersections where one street ends
or joins another street, there shall be at least one sign. Street
signs shall be erected before the first dwelling on the street is
occupied. Temporary street signs may be erected with the permission
of Borough Council. Any temporary signs will be replaced prior to
roadway dedication. Street sign letter size shall conform to standards
established pursuant to the Americans with Disabilities Act. Street
sign color and design shall reflect the style prevailing in the Borough
as interpreted by the Borough Engineer.
2.Â
Street Names. Street names shall be determined in consultation with
the Borough. Street names shall bear a reasonable relationship to
significant natural features or history of the community. Efforts
shall be made to reduce the occurrence of similar names or similar
sounding names within the Borough or postal delivery area.
[Ord. 1005, 5/23/2011]
1.Â
2.Â
General Requirements.
A.Â
The location, dimensions, and spacing of required plantings shall
be adequate for their proper growth and maintenance taking into account
the sizes of such plantings at maturity and their present and future
environmental requirements and tolerances including wind, moisture,
sunlight, pests and diseases.
B.Â
Plantings shall be selected and located where they will not contribute
to conditions hazardous to public safety. Such conditions include,
but are not limited to, public street rights-of-way, underground and
above ground utilities, and sight triangle areas required for unobstructed
views at street intersections.
3.Â
Plant Specifications. All plants shall meet the standards set forth
in the Borough of Hatboro Specifications and Design Standards, incorporated
herein by reference and as may be amended from time to time by Resolution
of Borough Council.
4.Â
Maintenance.
A.Â
Required plant material shall be perpetually maintained to achieve
the required visual effect of the buffer or screen. It shall be the
ultimate responsibility of successive landowners to ensure that the
required plantings are properly maintained. Dead or diseased plant
materials shall be removed or treated properly by the landowner and
replaced during the next growing season.
B.Â
Safety. All sight triangles shall remain clear, and any plant materials
that could endanger safety such as unstable limbs shall be removed
and the plant materials shall be replaced if necessary. It shall be
the responsibility of all property owners to maintain all plantings
and architectural elements to ensure a safe environment.
C.Â
Maintenance guidelines for the plantings are encouraged to be published
by the planting plan designer, to be used by grounds maintenance personnel.
D.Â
Replacement. Any tree or shrub which dies within 18 months of planting
shall be replaced by the current landowner or developer. Any tree
or shrub that within 18 months of planting is deemed, in the opinion
of Borough, not to have survived or not to have grown in a manner
characteristic of its species, shall be replaced. Substitutions for
certain species of plants may be made with the approval of the Borough.
E.Â
Landscaping shall also be planted around all detention basins, except
in locations where such landscaping would obstruct stormwater flows,
emergency spillways or sight distance.