A.
Purpose. In addition to the general purposes listed in Section 18.05.020 (Purpose, Intent, and Authority), the specific purposes of residential zoning districts are to:
1.
Preserve, protect, and enhance appropriately located areas for residential land use, consistent with the General Plan, Citywide Design Guidelines, and the standards of public health and safety.
2.
Protect residents from the harmful effects of excessive noise, overcrowding, excessive traffic, excessive on-street parking, and other adverse environmental effects.
3.
Achieve design compatibility between multi-family residential developments and lower density residential neighborhoods by establishing physical development standards and performance standards.
4.
Ensure adequate provisions for sites, with reasonable access to public services, for appropriate public and semipublic land uses, including care facilities, needed to complement or exist within residential development while protecting the relatively quiet, primarily noncommercial, family atmosphere of neighborhoods.
5.
Minimize the out-of-scale appearance of large homes, parking areas, and other development relative to their lot size and to other homes in a neighborhood.
6.
Provide for care facilities, emergency shelters, and supportive/transitional housing to meet current and projected need while ensuring compatibility with surrounding neighborhoods.
B.
Summary of Residential Zoning Districts. The specific purpose and intent of each of the 11 residential zoning districts are as follows:
1.
R-20, R-15 – Low Density Single-Family Residential Zoning Districts. The purpose of the R-20 and R-15 zoning districts is to allow for low density single-family residential development (1.3 to 3 dwelling units per acre) on larger lots ranging from 15,000 square feet in the R-15 zoning district to 20,000 square feet in the R-20 zoning district. The R-15 and R-20 zoning districts implement the Single-Family Low Density (SFLD) General Plan land use designations.
2.
R-10 and R-10A – Single-Family Medium Density Residential Zoning Districts. The purpose of the R-10 and R-10A zoning districts is to allow for low and medium density single-family residential development (3.1 to 4.5 dwelling units per acre). The minimum lot size in the R-10 zoning district is 10,000 square feet. The minimum lot size in the R-10A zoning district is 7,000 square feet with an average lot size of 10,000 square feet. The R-10 and R-10A zoning districts implement the Single-Family Medium Density (SFMD) General Plan land use designation.
3.
R-7 and R-6 – Single-Family High-Density Residential Zoning District. The purpose of the R-7 and R-6 zoning districts is to allow for higher density single-family and lower-density multi-family residential developments (e.g., duplexes, triplexes) and other compatible uses that promote neighborhoods with a mixture of housing types and sizes to meet community needs. The R-7 and R-6 zoning districts allow for densities between 4.6 to 6.9 dwelling units per acre. The R-6 zoning district has a minimum lot size of 6,313 square feet, whereas the R-7 zoning district has a minimum lot size of 7,000 square feet. The R-6 and R-7 zoning districts implement the Single-Family High-Density (SFHD) General Plan land use designation.
4.
RMD – Mangini Delu Residential Zoning District. The purpose of the RMD Zoning District is to allow for the development of a variety of housing types on the Mangini-Delu property while preserving natural open space. The RMD zoning district allows for densities between 4.6 to 13 dwelling units per acre to provide for a range of single-family and low-density multifamily housing options. Allowed uses and development standards in the RMD zoning district shall be established in a comprehensive, site wide master plan to be approved prior to any development onsite, unless otherwise provided in this Chapter. The RMD zoning district implements the Mangini-Delu Residential (MDR) General Plan land use designation.
5.
MFVL – Very Low Density Multi-Family Residential Zoning District. The purpose of the MFVL zoning district is to allow for higher density single-family residential uses and very low-density multi-family residential uses (e.g., duplexes, townhouses, triplexes). The MFVL zoning district allows for densities between seven and 12 dwelling units per acre and implements the Multi-Family Very Low-Density (MFVLD) General Plan land use designation.
6.
MFL – Low-Density Multi-Family Residential Zoning District. The purpose of the MFL zoning district is to allow for higher density single-family residential uses or low-density multi-family residential uses including duplexes, triplexes, manufactured housing, or small condominiums or apartments. The MFL zoning district allows for densities between 12.1 and 20 dwelling units per acre and implements the Multi-Family Low-Density (MFLD) General Plan land use designation.
7.
MFM – Medium-Density Multi-Family Residential Zoning District. The purpose of the MFM zoning district is to allow for multi-family residential uses including townhouses, manufactured housing, and mid-sized condominiums or apartments with densities between 20.1 and 30 dwelling units per acre. The MFM zoning district implements the Multi-Family Medium Density (MFMD) General Plan land use designation.
8.
MFH – High Density Multi-Family Residential Zoning District. The purpose of the MFH zoning district is to allow for more intensive multi-family residential uses including townhouses, condominiums and apartments with densities between 30.1 and 40 dwelling units per acre. The MFH zoning district implements the Multi-Family High-Density (MFHD) General Plan land use designation.
9.
MFVH – Very High Density Multi-Family Residential Zoning District. The purpose of the MFVH zoning district is to allow for intensive multi-family residential uses at higher densities (40.1 to 73 dwelling units per acre) including condominiums and apartment complexes. The MFVH zoning district implements the Multi-Family Very High-Density (MFVHD) General Plan land use designation.
10.
HPUD – Hillside Planned Unit Development Residential Zoning District. The purpose of the HPUD zoning district is to allow for limited residential development including townhouses, condominiums and single-family homes on parcels having an average slope of 15% or greater. The HPUD zoning district implements various single-family and multi-family General Plan land use designations. The following parcels shall be exempt from the HPUD standards established in this Part: (Reference: Chapter 18.35 (Hillside Planned Unit Development (HPUD))).
11.
PUD/PPD – Residential Planned Unit Development or Precise Plan District. The purpose of the PUD/PPD zoning district is to allow for residential development with a total number of dwelling units falls within the density range permitted by the associated General Plan land use designation for the total area allocated to residential use. (See also Government Code Section 65589.5.)
C.
Per Government Code Sections 65583.2(c), (h), and (i) lower-income sites including: those in the sites inventory with a proposed zoning change to meet the RHNA shortfall, vacant sites identified in two previous housing elements, and nonvacant sites identified in the previous housing element shall allow owner-occupied and rental multifamily uses permitted by-right (without discretionary approval) for developments in which 20% or more of the units are affordable to lower income households, accommodate a minimum of 16 units per site, and include a minimum density of 20 units per acre. "By-right" means that a Conditional Use Permit, Planned Unit Development Permit, or other discretionary review or approval is not required.
(Ord. 978, 11/17/2025)



