A. 
The sketch plan initially submitted to the Planning Board shall be based on Tax Map information or some other similarly accurate base map at a scale (preferably not less than 200 feet to the inch) to enable the entire tract to be shown on one sheet. The sketch plan shall be submitted, showing the following information:
(1) 
The location of that portion which is to be subdivided in relation to the entire tract and the distance to the nearest existing street intersection.
(2) 
All existing structures, wooded areas, streams and other significant physical features within the portion to be subdivided and within 200 feet thereof. If topographic conditions are significant, contours shall also be indicated at intervals of not more than five feet.
(3) 
The name of the owner and of all adjoining property owners as disclosed by the most recent municipal tax records.
(4) 
The Tax Map sheet, block and lot numbers, if available.
(5) 
All the utilities available and all streets which are either proposed, mapped or built.
(6) 
The proposed pattern of lots (including lot width and depth), street layout, recreation areas, systems of drainage, sewerage and water supply within the subdivided area.
(7) 
All existing restrictions on the use of land, including easements, covenants or zoning.
The following documents shall be submitted for approval:
A. 
Fifteen copies of the preliminary plat prepared at a scale of not more than 100 but preferably not less than 50 feet to the inch, showing:
(1) 
Proposed subdivision name, name of town and county in which it is located, date, true North point, scale, name and address of record owner, subdivider and engineer or surveyor, including license number and seal.
(2) 
The name of all subdivisions immediately adjacent and the name of the owners of record of all adjacent property.
(3) 
Zoning district, including exact boundary lines of district if more than one district, and any proposed changes in the Zoning Ordinance text applicable to the area to be subdivided.[1]
[1]
Editor's Note: See Ch. 700, Zoning.
(4) 
All parcels of land proposed to be dedicated to public use and the conditions of such dedication.
(5) 
Location of existing property lines, all survey monuments, easements, buildings, watercourses, marshes, rock outcrops, wetlands, wooded areas, single trees not part of a wooded area with a diameter of eight inches or more as measured three feet above the base of the trunk, and other significant existing features for the proposed subdivision and adjacent property.
(6) 
Location of existing storm sewers, water mains, culverts and drains on the property, with pipe sizes, grades and direction of flow.
(7) 
Contours with intervals of five feet or less as required by the Town Engineer and the Code Enforcement Officer, including elevations of existing roads; preliminary grading plan, if natural contours are to be changed by more than two feet on any point of the property.
(8) 
The width and location of any streets or public ways or places recognized by the Comprehensive Plan, if such exists, within the area to be subdivided and the width, location, grades and street profiles of all streets or public ways proposed by the developer.
(9) 
The approximate location and size of all proposed water lines, valves, hydrants and storm sewer lines and fire alarm boxes; connection to existing lines or alternate means of water supply and method of sewage disposal as required by the Public Health Law; profiles of all proposed water and storm sewer lines.
(10) 
Storm drainage plan indicating the approximate location and size of proposed lines and their profiles, connections to existing lines or alternate means of disposal.
(11) 
Plans and cross-sections showing the proposed location, size and type of sidewalks, streetlighting standards, street trees, curbs, water mains, storm drains, the character, width and depth of pavements and subbase, the location of manholes, basins and underground conduits.
(12) 
Preliminary design of any bridges or culverts which may be required.
(13) 
The proposed lot lines with approximate dimensions and area of each lot.
(14) 
Where the topography is such as to make difficult the inclusion of any of the required facilities within the public areas as laid out, the preliminary plat shall show the boundaries of proposed permanent easements over or under private property, which permanent easement shall not be less than 20 feet in width and which shall provide satisfactory access to an existing public highway or other public highway or public open space shown on the Subdivision or the Official Map.
(15) 
An actual field survey of the boundary lines of the tract giving complete descriptive data by bearings and distance made and certified by a licensed land surveyor; the corners of the tract shall also be located on the ground, marked by substantial monuments of such size and type approved by the Town Engineer, and shall be referenced and shown on the final plat.
B. 
If the application covers only a part of the subdivider's entire holding, a map of the entire tract drawn at a scale of not less than 400 feet to the inch showing an outline of the platted area with its proposed streets and indication of the probable future street system with existing grades and drainage in the remaining portion of the tract and the probable future drainage layout of the entire tract shall be submitted. The part of the subdivider's entire holding submitted shall be considered in relation to the entire holdings.
C. 
A copy of such covenants or deed restrictions as are intended to cover all or part of the tract.
The following documents shall be submitted for final plat approval:
A. 
The plat to be filed with the County Clerk shall be printed upon linen or be clearly drawn in India ink upon tracing cloth. The size of the sheets shall be 24 inches by 36 inches or 30 inches by 42 inches, including a margin for binding of two inches outside of the border along the left side and a margin of one inch outside of the border along the remaining sides. The plat shall be drawn at a scale of no more than 200 feet to the inch and oriented with the North point at the top of the map. When more than one sheet is required, an additional index sheet of the same size shall be filed showing to scale the entire subdivision with lot and block numbers clearly legible.
(1) 
The final plat shall show:
(a) 
Proposed subdivision name or identifying title and the name of the town and county in which the subdivision is located, the name and address of the record owner and subdivider, name, license number and seal of the licensed land surveyor.
(b) 
Street lines, pedestrianways, lots, reservations, easements and areas to be dedicated to public use.
(c) 
Sufficient data acceptable to the Town Engineer to readily determine the location, bearing and length of every street line, lot line and boundary line and to reproduce such lines upon the ground. Where applicable, these should be referenced to monuments included in the state system of plane coordinates and in any event should be tied to reference points previously established by a public authority.
(d) 
The length and bearing of all straight lines, radii, length of curves and central angles of all curves or tangent bearings shall be given for each street. All dimensions and angles of the lines of each lot shall also be given. All dimensions shall be shown in feet and decimals of a foot. The final plat shall show the boundaries of the property, location, graphic scale and true North direction.
(e) 
The final plat shall also show by proper designation thereon all public open spaces for which deeds are included and those spaces, title to which is reserved by the developer.
(f) 
All offers of cession and covenants governing the maintenance of unceded open space shall bear the certificate of approval of the Town Attorney as to their legal sufficiency.
(g) 
Lots and blocks within a subdivision shall be numbered and lettered in alphabetical order in accordance with the prevailing Town practice.
(h) 
Permanent reference monuments shall be shown and shall be constructed in accordance with the specifications of the Town Engineer. When referenced to the state system of plane coordinates, they shall also conform to the requirements of the State Department of Transportation. They shall be placed as directed by the Town Engineer and their location noted and referenced upon the plat.
(i) 
All lot corner markers shall be permanently located with at least 3/4 inches (if metal) in diameter and at least 24 inches in length and located in the ground flush with existing grade.
(j) 
Monuments of a type approved by the Town Engineer shall be set at all corners and angle points of the boundaries of the original tract to be subdivided; and at all street intersections, angle points in street lines, points of curve and such intermediate points as shall be required by the Town Engineer.
(k) 
Certification of Health Department approval.
B. 
Construction drawings, including plans, profiles and typical cross-sections, as required, showing the proposed location, size and type of streets, sidewalks, streetlighting standards, street trees, curbs, water mains, method of sewage disposal, storm drains, paving and grading, manholes, catch basins and other facilities.