[HISTORY: Adopted by the Common Council of
the City of Franklin 8-5-1997 by Ord. No. 97-1461 as Ch. 22 of the 1997
Code. Amendments noted where applicable.]
Except as otherwise regulated herein, the regulations
of this chapter shall govern all outdoor signs, advertising structures
or devices with respect to location, safety, size, construction, erection,
attachment, support, anchorage and maintenance.
For the purpose of this chapter, the following
words and phrases shall have the meanings assigned to them in this
section:
Wood, combustible plastics or other rigid material impervious
to water.
Only those combustible plastic materials which, when tested
in accordance with the American Society for Testing and Materials
Standard Method of Testing for Flammability of Plastics over 0.050
inch in thickness, D635 (Latest Revision), burn no faster than 2.5
inches per minute in sheets of 0.060 inch thickness.
The ultimate street line as established by the
Master Plan of the City and/or by an Official Map of the City. On
all such streets, the base setback line shall be located at a distance
from the center line of such street or 60 feet from the center point
of a cul-de-sac, unless specifically designated otherwise by the Council
of the City.
The base setback line of frontage roads shall
be located at a distance from the center line of such road equal to
1/2 of the right-of-way width of said frontage road.
All setback lines shall be parallel to and measured
at right angles to the center line of the street or highway.
Outdoor advertising on a board, poster, panel
structure or device of any kind used or intended to be used for advertising
or display painted therein, or for the affixment, attachment or support
of printed posters or other advertising matter, and constructed, erected
and located on any premises or attached to a wall or placed on a roof
of a building or structure now owned or occupied by the person for
whose use such billboard is constructed, erected, located or attached,
and when used for purposes other than advertising, the business conducted
on such premises or in such building or structure.
Such outdoor advertising constructed, erected
and located as aforesaid used for the purpose of advertising the business
conducted on premises or in a building or structure shall be deemed
a sign.
A sign not to exceed 15 square feet, located on public, charitable
or religious institutions.
A sign attached to or supported by a canopy.
The surface made available on the sign or billboard structure,
either for the direct mounting of letters and decorations or for the
mounting of facing material intended to carry the entire advertising
message.
The surface of the sign or billboard upon, against or through
which the message of the sign or billboard is exhibited.
A sign or billboard which is supported by one or more uprights
or braces in or upon the ground.
A sign attached to or supported by a hood.
The letters, illustrations, symbols, figures, insignia and
other services employed to express and illustrate the advertising
message.
A sign attached to or supported by a marquee.
The establishment of an identification program for any multitenant
operation within the City, including, but not limited to, office parks,
industrial parks and multitenant office and retail buildings. The
intent of a master sign program is to give a uniform theme of size,
color and style to signs in such a development. Each sign covered
by a master sign program must be permitted separately.
[Added 11-20-2007 by Ord. No. 2007-1934]
Any sign or billboard which lacks parts making it stationary
or which is not stationary and which is located on any premises for
longer than 48 hours.
A commercial development that contains a number of separate
commercial activities in which there are appurtenant facilities, such
as parking or a pedestrian mall, and which is designed to provide
a single area in which the public can obtain varied products and services.
Distinguishing characteristics of a MTCC may, but need not, include
common ownership of the real property upon which the center is located,
common wall construction and multiple-occupant commercial use of a
single structure. For the purpose of this chapter, MTCC also includes
separate parcels sharing common walls and facilities, but not necessarily
common owners. MTCC can be office, retail, or mixed use in character.
[Added 11-20-2007 by Ord. No. 2007-1934]
Any structure or device that is arranged, intended, designed
or used as an announcement, declaration, demonstration, display, illustration,
indication, symbol, insignia or emblem used to advertise, identify
or promote the interests of any person when the same is placed out
of doors in view of the general public, and shall include the supports,
uprights, bracing, framework and trim.
A collection of like-use buildings, residential (in the case
of mixed-use development), office, or industrial in nature, designed
and constructed contemporaneously and in close proximity to each other
as part of a single integrated project, including, but not limited
to, office or industrial parks.
[Added 11-20-2007 by Ord. No. 2007-1934]
A sign affixed or attached directly to the exterior wall
of a building or structure and extending more than 10 inches from
the exterior wall of the building or structure.
A sign or billboard constructed, erected and maintained on
or above the roof of any building or structure.
Any outdoor advertising other than a billboard.
A device, structure or symbol affixed permanently to the
ground, used and adopted as an identifying mark for the subdivided
area.
Any sign, banner, pennant, valance or advertising display
constructed of cloth, canvas, light fabric, cardboard, wallboard or
other light materials, with or without frames, intended to be displayed
for a period not to exceed 30 days.
The moldings, battens, cappings, nailing strips, latticing
and platforms which are attached to the sign or billboard structure.
A sign or billboard fixed or attached directly to the exterior
wall of a building or structure and extending not more than 10 inches
from the exterior wall of the building or structure.
A.
Permit required.
(1)
No person shall erect, construct, enlarge, move, relocate
or maintain any sign or billboard regulated in this chapter without
first obtaining a permit therefor from the Department of City Development
and paying the fee prescribed in this section.
[Amended 8-3-2021 by Ord. No. 2021-2475]
B.
Application for permit. Application for sign erection
permits shall be made upon blanks provided by the Department of City
Development and shall contain or have attached thereto the following
information:
[Amended 8-3-2021 by Ord. No. 2021-2475]
(1)
Name, address and telephone number of applicant.
(2)
Plot plan showing the location of the building, structure
or lot to which or upon which the sign or other advertising structure
is to be attached or erected and the sign or billboard location.
(3)
The location and type of any other signs or billboards
located or proposed to be located on the property.
(4)
Drawing of the sign or billboard to a scale not less
than 1/2 inch equals one foot.
C.
Issuance of permits.
[Amended 11-20-2007 by Ord. No. 2007-1934; 8-3-2021 by Ord. No. 2021-2475]
(1)
The Department of City Development, upon filing of
an application for a sign erection permit, shall examine such plans
and specifications and other data. The Department shall determine
whether the proposed structure is in compliance with the requirements
of this chapter and all other regulations of the City.
(2)
Upon its determination that the proposed structure
conforms with the ordinances of the City, the Department of City Development
staff shall issue the permit. If the work authorized under the sign
permit has not been completed within one year after the date of issuance,
the permit shall become null and void.
D.
Permit fees.
[Amended 2-25-2002 by Ord. No. 2002-1702; 11-20-2007 by Ord. No. 2007-1934; 7-13-2010 by Ord. No. 2010-2008; 5-5-2015 by Ord. No. 2015-2173]
(1)
Together with the application fee for each and every master sign
program, amendment to a master sign program or sign or billboard,
the applicant shall pay a permit fee as provided below. If the sign
or billboard is not approved and no permit is issued, or if the sign
is approved but no permit is obtained, the application fee shall be
retained by the City to cover the cost of processing the application.
(a)
Application fees.
(2)
Every applicant, before being granted a permit, shall pay the following
permit fee or fees for such sign or other advertising structure regulated
by this chapter.
(a)
For any and all signs or billboards, an original permit fee
or permit renewal shall be paid per the following schedule:
[1]
For eight square feet or less: $40.
[2]
For nine to 50 square feet: $75.
[3]
For 51 to 100 square feet: $100.
[4]
For 101 to 150 square feet: $150.
[5]
For 151 square feet or larger: $150 plus $25 each additional
100 square feet.
[6]
Additional fee for illuminated sign: $50 each sign.
[7]
Reinspection fee: $75 per inspection.
[8]
Failure to call for a required inspection: $100.
(b)
Mobile and temporary signs: $75 each permit or renewal.
[Amended 8-3-2021 by Ord. No. 2021-2475]
(c)
[1]Technology fees.
[1]
Permit fee is less than $100: $2 per permit.
[2]
Permit fee is greater than or equal to $100: $5 per permit.
NOTE:
|
Before any work is commenced or recommenced after a permit has
expired, a new permit shall be reissued at 1/2 the regular fee, or
at the reinspection rate for each remaining inspection. The method
used shall be determined by, and at the sole discretion of, the Department
of City Development.
[Amended 8-3-2021 by Ord. No. 2021-2475] | |
NOTE:
|
If construction is not commenced prior to expiration of the
permit, that portion of the permit fee, excluding plan exam fees,
that exceeds the minimum fee will be refunded upon written request.
|
[1]
Editor's Note: Former Subsection D(2)(c), Architectural Board
review fee, was repealed 8-3-2021 by Ord. No. 2021-2475, which ordinance
also redesignated former Subsection D(2)(d) as Subsection D(2)(c).
E.
Revocation of permits. The Department of City Development
may revoke any permit issued by said Department or refuse to issue
a permit upon failure of the holder to comply with any provision of
this chapter.
[Amended 8-3-2021 by Ord. No. 2021-2475]
A.
Permissible areas for signs.
(1)
Other than residential districts. In nonresidential districts, signs and billboards shall be permitted, and any electrical service shall be regulated under/by Chapter 118, Electrical Standards.
[Amended 8-3-2021 by Ord. No. 2021-2475]
(2)
Residential districts. Anyone conducting a business
in any residential district in the City shall be permitted to have
one sign or nameplate advertising the business conducted on the sign.
If any business is being conducted in a residential district on any
premises which are adjacent or contiguous to other premises used for
business purposes, but to which direct access is not obtained from
any public street or highway, an additional sign or nameplate not
to exceed six square feet in size may be permitted on the business
premises adjacent to the public street or highway to advertise the
business being conducted on the premises to which direct access is
not available from a public street or highway.
B.
Prohibited areas for signs and billboards.
(1)
No billboards shall be permitted in a residential
district in the City.
(2)
No signs shall be permitted in a residential district
in the City except as herein specifically provided.
(3)
No sign or billboard shall be constructed, erected
or maintained which shall be nearer to the street or highway than
the established base setback line provided by the zoning regulations
of the City.
(4)
No signs, excepting official City, county or state
regulatory signs, shall be erected, installed or posted on and within
any public right-of-way within the corporate limits of the City.
C.
Standards for the design and erection of signs and
billboards.
(1)
Location; obstruction.
(a)
No sign or billboard, or any part thereof, shall
be erected, constructed or maintained so as to obstruct any exit,
window opening necessary for required light or ventilation or other
opening of a building or so as to prevent free passage from one part
of a roof to any other part thereof.
(b)
No sign or billboard shall be attached to or
erected and maintained on any premises on any standpipe, exterior
stairway, fire escape, smokeproof stair, tower balcony or balcony
serving as a horizontal exit or so as to interfere with the use thereof.
(c)
No sign or other advertising structure as regulated
by this chapter shall be erected at or near the intersection of any
street in such manner as to obstruct free and clear vision; or at
any location where, by reason of the position, shape or color, it
may interfere with, obstruct the view or or be confused with any authorized
traffic sign, signal or device; or which makes use of the words "Stop,"
"Look," "Danger" or any other word, phrase, symbol or character in
such manner as to interfere with, mislead or confuse traffic.
(d)
Except within an MTCC or planned development
having a master sign program, wherein the total amount of signage
permitted shall be calculated by multiplying the aggregate lineal
front footage of all buildings by a factor of 1.5 square feet, the
total amount of signage permitted for each business premises within
a business district shall be determined by the greater of the product
obtained by multiplying either the lineal front footage of the main
building of the business facing the adjacent roadway by a factor of
1.5 square feet or multiplying the lineal front footage of the business
premises lot by a factor of 0.8 square feet. Either factor may be
increased by a factor of 0.5 square feet for each 50 feet of setback
beyond 100 feet, to a maximum of 500 feet. However, each business
premises located on the ground floor shall be entitled to minimum
total signage of 40 square feet per ground floor business premises.
The owner of a multi-tenant building is responsible for dividing the
gross allowable signage among all tenants of the multi-tenant building.
No business premises shall have more than two signs. Each business
premises may have one monument sign.
[Amended 11-20-2007 by Ord. No. 2007-1934; 1-22-2008 by Ord. No. 2008-1936]
(e)
Except within an MTCC or planned development
having a master sign program, wherein the total amount of signage
permitted shall be calculated by multiplying the aggregate lineal
front footage of all buildings by a factor of 1.5 square feet, the
total amount of signage permitted for each business premises within
the Industrial District shall be determined by the greater of the
product obtained by multiplying either the lineal front footage of
the main building of the business facing the adjacent roadway by a
factor of two square feet or multiplying the lineal front footage
of the business premises lot by a factor of 0.8 square feet. The owner
of a multi-tenant building is responsible for dividing the gross allowable
signage among all tenants of the multi-tenant building. No business
premises may have more than two signs. Each business premises may
have one monument sign. As an exemption to the restrictions for signs
in the Industrial District, nonilluminated directional signs shall
be allowed on industrial premises, provided that they do not exceed
six square feet in area and, if they are either ground, post or pylon
signs, they do not exceed five feet in height measured from the top
of the sign to the ground immediately below the sign.
[Amended 11-20-2007 by Ord. No. 2007-1934; 1-22-2008 by Ord. No. 2008-1936]
(2)
Wind pressure, allowable stresses and materials.
(a)
All signs and billboards shall be constructed,
erected and maintained to safely withstand a wind pressure of not
less than 30 pounds per square foot.
(b)
The allowable stresses in chains, wire ropes,
and steel guy rods and their fastenings shall not exceed 1/4 of their
ultimate strength.
(c)
All ferrous chains, wire ropes, guy rods and
their fastenings and anchor bolts shall be galvanized or be of other
approved equivalent protection. All other ferrous parts of signs or
billboards subject to corrosion shall be protected and maintained
free from corrosion by approved corrosion-resistant coating.
(3)
Identification.
(a)
All signs hereafter erected shall bear the manufacturer's
name, and the name trademark or other approval mark or symbol of the
person erecting such sign.
(b)
All billboards hereafter erected shall bear
the name, trademark or other approved mark or symbol of the erector
or of the person in charge, possession or control of such billboard.
(4)
Combustible facings, letters and decoration, etc.
(a)
Facings. Facings of signs and billboards may
be made of approved combustible plastics, provided that the supports,
uprights, bracing framewood and structural trim is made from noncombustible
material, and provided that the surface area of each face is not in
excess of 100 square feet, and provided, further, that such faces
shall be separated from each other in an approved manner with noncombustible
material. The letters and decorations mounted upon such plastic facings
may be made of approved combustible plastics.
(b)
Letters and decorations. The area of the display
surface or facing occupied or covered by plastic letters or decorations
shall not exceed a total area calculated on the following basis:
Display Surfaces
|
Covered by Plastics
|
---|---|
100 square feet or less
|
100% of display surface area
|
Over 100 square feet but not over 2,000 square
feet
|
100 square feet plus 25% of the difference between
100 square feet and the area of the display surface
|
2,000 square feet
|
Not more than 575 square feet
|
(5)
Monument sign.
[Amended 11-20-2007 by Ord. No. 2007-1934]
(a)
Description: a permanent, freestanding sign
having a solid appearance, consisting of a face and base. The width
of the base must be at least 1/2 the width of the widest part of the
sign face. The base must be constructed with stone, decorative concrete,
brick or other durable and aesthetically pleasing materials in keeping
with the architectural integrity of the building the sign is representing.
The monument sign sign content area must be attached in a continuous
fashion to a proportionate base. Monument signs have no exposed supports
other than the base itself.
(b)
Number. No more than one monument sign shall
be erected on each public street frontage of a property, except with
the approval of the Plan Commission, considering the effect upon the
aesthetics of and visual harmony with the vicinity and considering
any other such factor the Plan Commission shall deem appropriate.
(c)
Area. The area of a monument sign shall not
exceed 120 square feet total sign face, which shall include the aggregate
sign face area of a multi-sided sign.
[Amended 8-3-2021 by Ord. No. 2021-2475]
(d)
Location:
[1]
Monument signs shall not be closer than 500 feet to another monument sign, except where such distance is not attainable in providing for the allowance that "Each business premises may have one monument sign," as per § 210-4C(1)(d) and (e), in which case the initial determination of placement shall be as established by the Department of City Development, when not otherwise under the jurisdiction of the Plan Commission.
[Amended 6-20-2017 by Ord. No. 2017-2279]
[2]
Monument signs will be permitted to flank driveways,
provided that the height of each sign shall not exceed six feet in
height and 60 square feet in area, and also provided that the monument
signs are within 50 feet of the driveway.
[3]
When a building is set back less than 30 feet
from the property line, a monument sign shall not be permitted to
be installed in the areas identified below:
[Amended 5-17-2011 by Ord. No. 2011-2047]
[a]
Anywhere along the property frontage having a building set back less
than 30 feet and between the two boundaries created by parallel lines
extending from each side of the building's footprint which intersect
said property line perpendicular to the right-of-way.
[b]
Anywhere along a property frontage having a building set back less
than 30 feet and between the two boundaries created by parallel lines
extending from each side of the building's footprint, from the point
at which the building crosses the thirty-foot setback, which intersect
said property line perpendicular to the right-of-way and then expanding
that range 30 feet in each direction along the property frontage.
[c]
Where the monument sign would infringe upon, interfere with, or replace
approved architectural or landscaping features.
[4]
No part of any monument sign may be closer than
three feet to a lot line.
[5]
A monument sign may not be located so as to
create an obstruction within the vision triangle as determined by
and at the discretion of the Department of City Development.
(e)
Height. The maximum sign height of a monument
sign, including the base, shall not exceed 14 feet at the highest
point of the sign. The maximum height of the sign base shall not exceed
four feet. The height of the sign shall be measured from the nearest
adjacent road grade at the edge of the pavement to the highest point
of the sign and/or supporting structure of the sign, excepting that
under no circumstances shall the maximum height of a monument sign
exceed 18 feet, measured from ground level at the base to the highest
point of the sign.
(f)
Material and color compatibility. The color
scheme of monument signs must be consistent with the color scheme
of the principal building, unless an alternate color scheme is required
by an approved master sign program.
(6)
Roof signs and roof billboards.
(a)
Materials bottom clearance.
[1]
Roof signs and billboards not exceeding at any point 13 feet in height from the lower to the upper edge of the facing may be constructed of materials as regulated in Subsection C(5)(a). Roof signs and billboards exceeding such height shall be constructed of noncombustible materials, except mouldings and furring strips.
[2]
An open space not less than four feet shall
be maintained between the bottom of the sign or billboard facing and
the roof, except that necessary supports extending through such space
will be permitted.
(b)
Height. The height of the solid face of any
sign or billboard placed on the roof of any building shall be limited
to 12 feet. Any lettering or figures attached to the top of the roof
sign or billboard shall not exceed five feet in height. On buildings
50 feet more in height, signs or billboards thereon shall not exceed
50% of the height of the buildings.
(c)
Location.
[1]
When a roof sign or billboard is erected parallel
to the exterior wall of a building, the distance between the facing
of such sign and the parallel wall of the building shall be not less
than five feet. When a roof sign or billboard is erected at an angle
to the exterior wall of the building, the distance between the sign
and the exterior wall shall be not less than 2 1/2 feet.
[2]
No roof sign or billboard shall be erected on
a building of ordinary or frame construction, unless such building
is structurally capable of supporting such additional load with a
factor or safety of two.
(d)
Supports and anchorage.
[1]
Roof signs and billboards shall be secured and
anchored in an approved manner to buildings or structures over which
they are constructed or erected. The dead and wind loads of such signs
and billboards shall be distributed to the structural members of the
building or structure in such a manner that no structural member shall
be overstressed.
[2]
Uplift due to overturning of roof signs and
billboard shall be resisted by approved anchorage to the building
or structure. Approved anchorage to the building or structure shall
include such alterations to the buildings or structure as may be needed
to integrate and interconnect sufficient dead load to equal not less
than 10% in excess of the computed uplift applied to such building
or structure by the sign or billboard.
(7)
Wall signs and wall billboards.
(a)
Materials. Wall signs and billboards not exceeding at any point 13 feet in height from the lower to the upper edge of the facing may be constructed as regulated in Subsection C(5)(a). Wall signs and billboards exceeding such height shall be constructed of noncombustible materials, except mouldings and furring strips.
(b)
Height.
[1]
No part of a combustible wall sign or billboard shall be erected or maintained above the sill of a second-story window or windows of the building or structure to which such sign or billboard is to be attached, nor shall any part of such a sign or billboard be more than 30 feet above the established grade immediately below, except as further regulated in Subsection C(7)(b)[2] and except that an automobile dealership with at least 300 feet of frontage on a public highway may erect and maintain one identification wall sign upon its business or institutional premises or location, no part of which shall be more than 35 feet above the established grade immediately below.
[2]
No wall signs or billboards shall be erected
or maintained to extend more than 1/2 of the height thereof above
the top of the exterior wall to which attached.
(c)
Location.
[1]
No part of any wall sign or billboard, except
lighting reflectors, shall extend more than 10 inches from the face
of the wall to which such sign or billboard is attached. Lighting
reflectors, when at least 10 feet above the established grade immediately
below, may extend eight feet beyond the face of the wall, but not
beyond the base setback line.
[2]
No wall sign or billboard shall be erected or
maintained to extend beyond the street end of the wall to which such
sign or billboard is attached.
(d)
Supports and anchorage.
[1]
Wall signs and billboards attached to exterior
walls of concrete or masonry shall be securely fastened to such walls
by means of metal anchors, bolts, expansion screws or by other approved
method which will ensure stability and safety, but no fastening shall
be of less strength or performance than that provided by a three-eighths-inch
diameter expansion sleeve imbedded within the masonry or concrete.
[2]
Except in the case of wall signs or billboards
attached to buildings or structures with walls of wood, no wooden
blocks or anchorage with wood used in connection with screws or nails
shall be considered approved anchorage.
[3]
No wall sign or billboard shall be entirely
supported by a parapet wall.
(8)
Projecting signs.
(a)
Materials.
[1]
All projecting signs shall be constructed of noncombustible materials; provided, however, that the letters, decorations and facing of signs may be of approved combustible plastics when in compliance with Subsection C(5)(a).
[2]
Glass or porcelain shall be wired glass or porcelain
or shall be protected with a wire screen of a mesh of such size as
to prevent broken pieces thereof from falling upon the public, excepting
signs with molded glass letters of which only the letters or trademarks
are exposed.
[3]
Glass globes or glass signs shall be made of wired glass or protected with a wire screen as regulated in Subsection C(8)(a)[2] above. All globes shall be suspended in an approved manner from the building or structure.
(b)
Projection; clearance.
[1]
All signs projecting from a building or other
structure shall not project beyond the base setback line.
[2]
Projecting signs erected over marquees shall
be set back not less than two feet from the outer edge of such marquee.
[3]
No projecting sign shall at the lowest point
be less than 10 feet above the established grade immediately below.
(c)
Supports and attachment.
[1]
The dead load of projecting signs and the load
due to wind pressure shall be supported entirely by the building or
structure to which such signs are attached by means of structural
shapes, chains, wire ropes or steel guy rods; lateral supports shall
be spaced not more than eight feet apart unless otherwise approved.
Turnbuckles or other approved means of adjustment shall be placed
in all chains, wire ropes or steel rods supporting or bracing projecting
signs. No staples, nails or wire shall be used to secure any projecting
sign to any building or structure.
[2]
No part of a projecting sign shall be supported
from a parapet wall unless approved bracing is provided.
[3]
Where projecting sign supports are fastened
to walls or wood construction, the supporting device shall be fastened
securely in an approved manner.
[4]
All projecting perpendicular signs having a
facing of more than six feet in height shall be provided with a perpendicular
metal ladder not less than eight inches wide at the inner edge of
such sign and constructed in such manner as to provide access for
the repairing or inspection of such signs.
[5]
Ground or pole signs shall have approved vertical
supports of metal.
(9)
Marquee signs.
(a)
Materials.
[1]
All marquee signs shall be constructed of noncombustible materials; provided, however, that the letters, decorations and facings of signs so constructed may be made of approved combustible plastics when in compliance with the regulations of § 210-2, "approved combustible plastics."
[2]
Glass or porcelain when used shall be wired glass or porcelain or shall be protected as regulated in Subsection C(8)(a)[2].
(b)
Length and height.
[1]
Marquee signs may be attached directly to or
made a part of the sides or front face of a marquee, and such signs
may extend the entire length or width of such marquee but not beyond
such length or width. Such sign or signs shall not exceed eight feet
in vertical dimension, nor shall such sign or signs extend below the
face of a marquee.
[2]
Signs may be erected on the roof of a marquee,
provided that the total combined heights of the sign on the face of
the marquee and the sign erected on the roof shall not exceed 13 feet.
Any such sign shall not be closer than two feet from the outer edge
of the marquee.
(10)
Canopy signs.
(b)
Length and height.
[1]
Except as regulated in Subsection C(10)(b)[3], canopy signs may be attached directly to or made a part of the sides or front face of a canopy. Such signs may extend the entire length or width and shall not exceed 18 inches in vertical dimension or extend below the face of a canopy.
[2]
Except as regulated in Subsection C(10)(b)[3], canopy signs may be erected on the roof of a canopy, provided that such signs do not extend more than 18 inches above the top edge of the canopy. Such canopy roof signs shall not extend beyond the length or width of the canopy.
[3]
A canopy on any one building or structure may
have signs attached thereto or placed thereon as permitted in either
Subsection C(10(b)[1] or [2], but in no case shall there be placed
or erected on such canopy both types of signs.
(11)
Hood signs.
(12)
Clock signs.
(a)
All clock signs hereafter erected shall be attached
directly to and supported by the exterior wall within a building or
structure. Such signs shall be either wall signs or projecting signs
and shall conform to the applicable regulations of this chapter.
(13)
Billboards.
(a)
Materials, height, location, supports and anchorage
for billboards shall be regulated as specified in the sections of
this chapter pertaining to ground, wall and roof signs.
(b)
Billboards, as defined by this chapter, may
be erected only if the following requirements, in addition to all
other applicable requirements of this chapter, are met:
[1]
The billboard advertises a specific business
which is being conducted within the limits of the City or within 2,500
lineal feet of said City limits.
[2]
The billboard is located along a street or highway
which leads directly to the business being advertised or intersects
the street upon which the business is located at a point not more
than 2,500 lineal feet from said business.
[3]
The billboard, if presenting a commercial or
advertising message, may not exceed 200 square feet in area unless
approved as part of a master sign program.
[Added 11-20-2007 by Ord. No. 2007-1934]
(14)
Illuminated signs and billboards.
(a)
The face or faces of illuminated projecting
signs shall be be electrically illuminated in an approved manner.
Such illumination shall be an integral part of such signs.
(b)
Electrical illumination of signs in residence
use districts shall be as regulated in the State Electrical Code.
(c)
All illumination of or on signs or billboards
shall be by means of electricity and shall conform to the regulations
of the State Electrical Code. It shall be the policy of the Building
Inspector to approve, subject to the regulations of this chapter and
the State Electrical Code, any illuminated sign or billboard bearing
the Underwriters Laboratories, Inc., Label of Approval.
(d)
Goose neck reflectors and lights shall be permitted
on ground signs, roof signs and wall signs; provided, however, that
the reflectors shall be provided with proper glass lenses concentrating
the illumination upon the area of the sign so as to prevent glare
upon the street or adjacent property.
(e)
No person shall maintain any sign which is wholly
or partially lighted by spotlights or floodlights unless such spotlights
or floodlights are hooded or shielded in a manner approved by the
Electrical Inspector. No person shall use any rotating or flashing
spotlight or floodlight on any sign or for the purpose of illuminating
or displaying of such sign.
(15)
Signs and billboards on public property, snipe advertising,
etc.
(a)
No person, except a public officer or a government
employee in the performance of a public duty, shall maintain, place,
erect, paint, paste, print, nail, tack or otherwise fasten any card
banner, picture, handbill, sign, poster, advertising or notice of
any kind or cause the same to be done on any curb, streetwalk or public
thoroughfare surface, fence, board, barrel, box, case, railing, pole,
post, bridge, tree, barricade, material, bridge fender, dock, pile,
building or structure of any kind on public ground or public waterway
or upon any structure projecting over any public thoroughfare, public
ground or public waterway within the City except as may be permitted
by this chapter or other ordinance, the Superintendent of Public Works,
the Council, statutes of the state or federal laws.
(b)
No person shall place, erect, paint, paste,
print, nail, tack or otherwise fasten or maintain any "snipe" advertising
or deface any exterior wall or surface of any building, board, barrel,
box, case, railing, pole, post, tree, barricade, material, dock, pile
or structure of any kind with advertising or notice of any kind.
(c)
Except as permitted by this chapter, no person
shall place, erect, tack or otherwise fasten or use or maintain any
outdoor advertising, such as banners, decorative displays or other
advertising devices, or cloth, paper or other nonrigid materials.
(16)
Other advertising devices. Any advertising device
not herein regulated shall be constructed and erected in a manner
approved by the Plan Commission.
A.
Unsafe and unlawful signs.
[Amended 8-3-2021 by Ord. No. 2021-2475]
(1)
If the Planning Manager or, at his or her request,
the Director of Inspection Services, shall find that any sign or other
advertising structure regulated herein is unsafe or insecure or is
a menace to the public or has been constructed or erected or is being
maintained in violation of the provisions of this chapter, he or she
shall give written notice to the licensee thereof. If the licensee
fails to remove or alter the structure so as to comply with the standards
herein set forth within 10 days after such notice, such sign or other
advertising structure may be removed or altered to comply by the Department
of City Development or the Department of Inspection Services at the
expense of the licensee or owner of the property upon which it is
located. The Department of City Development shall refuse to issue
a license to any licensee or owner who refuses to pay costs so assessed.
(2)
The Planning Manager or, at his or her request, the
Building Inspector may cause any sign or other advertising structure
which is, in his or her opinion, an immediate peril to persons or
property to be removed summarily and without notice.
B.
Painting requirements.
(1)
The owner of any sign or billboard as defined and
regulated by this chapter shall have properly painted all parts and
supports of said sign or billboard as directed by the Department of
City Development unless the same are galvanized or otherwise treated
to prevent rust or deterioration.
[Amended 8-3-2021 by Ord. No. 2021-2475]
C.
Removal of certain signs and billboards.
(1)
Any sign or billboard now or hereafter existing which
no longer advertises a bona fide business or a product sold or is
dilapidated or out of repair shall be taken down and removed by the
owner, agent or person having the beneficial use of the building or
land upon which such sign or billboard may be found within 10 days
after written notification from the Building Inspector and, upon failure
to comply with such notice within the time specified in such order,
the Building Inspector may cause removal of such sign or billboard,
and any expense incident thereto shall be paid by the owner of the
building or land to which such sign or billboard is attached. If such
cost and expenses are not paid within 10 days from the date of billing,
the costs and expenses incurred for such removal shall be assessed
against the real estate upon which such sign is located and collected
as other taxes are collected on said real estate.
(2)
Any sign or billboard which is constructed after November
16, 1967, without a permit shall be removed or a permit be applied
for, together with double fees, upon five days' notice to the owner.
Such notice shall be given by the Building Inspector by mail.
(3)
If the owner of such sign or billboard cannot be ascertained
by the Building Inspector, such notice shall be given to the owner
of the real estate upon which such sign or billboard is located. If
the owner of such real estate does not pay the amount thereof within
10 days from the billing, such cost and expense shall be assessed
against the real estate upon which such sign or billboard is located
and collected as other taxes are collected on said real estate.
(4)
If the permit be denied, the Department of City Development
shall issue a five-day removal notice, and if such sign or billboard
is not removed within such period, the same may be removed by the
Department of City Development and the cost thereof charged and assessed
as hereinabove provided.
[Amended 8-3-2021 by Ord. No. 2021-2475]
The following outdoor signs, advertising structures or devices shall be exempted from § 210-3:
A.
Up to two signs, at the same time, for each premises or tenant space,
where applicable, appertaining to the lease, sale, or new or pending
business or commercial occupancy of any building or land, provided
that each such sign does not exceed 32 square feet in area, is located
upon the premises, and, for such a sign promoting the new or pending
business or commercial occupancy, is not existing prior to commencement
of construction occurring under a valid building permit and is removed
within 60 calendar days following occupancy, issuance of an occupancy
permit, or issuance of a conditional occupancy permit, whichever occurs
first. Each sign may be single- or double-faced and must not exceed
eight feet in height. For the purposes of this section, a residential
subdivision (including the residential component of a mixed-use development),
with an approved and executed development agreement, shall be considered
a "new or pending business," as referenced above; and for any such
residential subdivision, "60 calendar days following occupancy" shall
mean "60 calendar days after 70% of the units are sold."
[Amended 6-20-2017 by Ord. No. 2017-2279; 6-5-2018 by Ord. No. 2018-2327]
B.
Signs not exceeding three square feet in size maintained
by the owner or occupant of any land or any building for the purpose
of displaying the name of the owner or occupant or for the purpose
of warning against trespasses.
C.
Bulletin boards not over 15 square feet in size for
public, charitable or religious institutions when the same are located
on the premises of said institutions.
D.
Memorial signs or tablets, names of buildings and
date of erection when cut into any masonry surface or when constructed
of bronze or other incombustible materials.
E.
Traffic or other municipal signs, legal notices, railroad
crossing signs, danger and such temporary emergency or nonadvertising
signs as may be approved by the Common Council.
G.
Letters or numerals attached to or signs painted on
glass surfaces of windows or doors.
H.
Signs used in connection with movable and fixed awnings.
I.
Nonilluminated signs painted on canopies, hoods and
marquees indicating only the name, street number and character of
the business of the owner, tenant or building when consisting of letters
and decorations not exceeding six inches in height.
J.
Signs not to exceed 20 square feet, identifying farm
or estate property on parcels of land containing not less than three
acres.
K.
Flags or banners representing the United States, State
of Wisconsin, County of Milwaukee, City of Franklin or other organizations
approved by the Council.
L.
Political signs that comply with all other sections
of the this chapter, provided that they be removed within 10 days
after an election and they do not exceed 35 square feet in size in
nonresidential districts.
The following outdoor signs, advertising structures or devices shall be exempted from § 210-3D:
B.
Subdivision emblems when an agreement regarding such
emblems has been entered into with the City.
C.
Special decorative displays or signs in public thoroughfares
when authorized by the Council.
D.
An approved sign not more than 12 square feet in area
painted on or attached to a temporary enclosure used in connection
with alterations to buildings or structures denoting continuance of
occupancy.
E.
Temporary signs.
[Added 11-20-2007 by Ord. No. 2007-1934]
A.
All MTCCs and planned developments, including, but not limited to,
office parks, industrial parks, office centers, retail centers, office
and limited-business structures, and churches and schools which have
a campus, must have a master sign program if, after January 1, 2007,
more than one sign will be erected in conjunction with such building,
development, or center, as defined in this chapter, except, effective
June 30, 2017, through June 30, 2020, said requirement for a master
sign program shall become discretionary for said property owners
in order to provide a temporary waiver from this requirement to provide
a period of time for additional municipal review of the requirement.
[Amended 6-20-2017 by Ord. No. 2017-2279; 6-5-2018 by Ord. No. 2018-2327; 7-2-2019 by Ord. No. 2019-2383]
B.
An application for a master sign program must first
be filed with the Department of City Development, which shall forward
it to the Plan Commission for consideration.
[Amended 8-3-2021 by Ord. No. 2021-2475]
C.
Each individual sign proposed in accordance with an
approved master sign program must be applied for and permitted separately
in accordance with this chapter, and in no event shall any recommendation
or approval of a master sign program be deemed an approval of or a
permission to construct any particular sign under that program. All
applications for permits for such signs must be filed with the Department
of City Development for approval under the terms and conditions of
the previously approved master sign program, except the application
must specify in exact terms any sign characteristics which the master
sign program considered in general or nonspecific terms or measurements.
The Department of City Development may approve or deny such application
or may forward the application to the Plan Commission for its denial,
approval, or approval with conditions or modifications, including
but not limited to modification of the previously approved master
sign program, provided such modification was duly noticed and the
master sign program application fee is paid.
[Amended 8-3-2021 by Ord. No. 2021-2475]
D.
The Plan Commission shall hear all requests for the
establishment or amendment of a master sign program, make written
findings, and approve, modify, approve with conditions, or deny such
requests.
E.
A master sign program, as presented to the Plan Commission,
shall include the following components:
(1)
An aesthetically developed theme on color, size, and
style;
(2)
A proposed location of all permanent signs for the
building, development, or center, which considers that, where possible,
wall signs shall be centered over tenant spaces;
(3)
The proposed size of individual signs, which may be
expressed in maximums and minimums for purposes of the proposed master
sign program;
(4)
The following categories of signs may be proposed
and approved for inclusion in a master sign program:
(a)
Master identification sign: a freestanding monument
sign which identifies a MTCC or planned development;
(b)
Tenant identification sign, separate from such
identification that may be made as part of a master identification
sign:
[1]
Tenant identification signs at individual tenant
entrances in an office center may not exceed four square feet in area
if permitted.
[2]
Retail tenants occupying not less than 20% of
an office and limited business structure with individual entrances
to the exterior may be allowed tenant identification similar to tenants
in retail centers. In both instances, the area of such signage shall
not exceed 1.5 times the lineal front foot of the space occupied unless
provided a special exception.
(c)
Tenant/service/product directory board for an
office center or office and limited business structure;
(d)
Entrance markers;
(e)
Traffic directional signs;
(f)
Wall signs for retail centers; and
(g)
Such other signs as requested by the applicant.
(5)
Nature and characteristics of signage proposed, i.e.,
individual letters, box, etc.;
(6)
Blueprints, drawings, and written policies governing
the color, size, style, location and other features of the proposed
signs, including but not limited to the proposed allocation or distribution
of the total signage allowance to individual tenants or tenant spaces;
and
F.
Review criteria. The Plan Commission, in its discretion,
will consider the following and/or other factors as it deems appropriate.
(1)
Scale and proportion: All signs shall be in scale
and proportion in their design and their relationship to other signs,
buildings, and surroundings.
(2)
Integral elements: Signs shall be designed as integral
architectural elements of the building and the site and not appear
as add-ons or intrusions.
(3)
Harmonious design: The colors, materials, and lighting
of each sign shall be compatible and harmonious with the design of
the building and the site.
(4)
Composition: The graphic design elements of the sign,
including consideration that the size of individual sign letters shall
be in reasonable proportion to the area of the facade of the building
or tenant space.
(5)
Compatibility: Signs shall be compatible with signs
on adjacent properties.
(6)
Unified image: The proposed signs submitted as part
of the master sign program review shall provide a unified image for
the development.
(7)
Type and location of the building and development
site.
(8)
The proposed tenant mix and proposed allocation or
distribution of the total signage allowance to individual tenants
or tenant spaces, which allocation or distribution may be restricted
or conditioned within a master sign program.
(9)
The size of the development.
G.
Master identification signs.
(1)
The purpose of the master identification sign is to
advertise a center. Therefore, for an MTCC or planned development,
a minimum of 50% of the sign must be devoted to center identification,
rather than individual tenants.
(2)
Application for a master identification sign shall be made in accordance with Subsection C. The following entities may make such application:
(a)
Retail or mixed-use MTCC or planned developments
of five or more individual tenants or at least fifty thousand (50,000)
square feet of building area;
(b)
Office MTCC or planned developments of five
or more tenants having exterior entrances;
(c)
Office parks and industrial parks; and
(d)
Developments that have multiple entry points
(e.g., churches, schools), where multiple buildings are used, along
with multiple uses, and where a need to direct traffic within the
campus exists.
(3)
MTCCs or planned developments of four or fewer tenants may not make application for a master identification sign except as provided in Subsection G(2)(a) of this section.
(4)
Architecture of master identification signs. Master
identification signs must be architecturally integrated with the principal
building on the property. The following considerations must be made
when designing a master identification sign:
(a)
The base of the sign must be constructed of
masonry products. The tone and texture of the base shall reflect the
principal building construction as close as possible. The base of
the sign must be equal or larger in width to the sign face.
(b)
The color scheme of the sign shall follow the
color scheme of the principal building.
(c)
Architectural features (such as sills, piers,
reveals, capstones, medallions, etc.) which are part of the architectural
makeup of the building shall be incorporated into the sign.
(d)
The sign face shall be constructed of aluminum,
masonry, or similar products. Polycarbonate backgrounds shall be prohibited,
unless this cannot be achieved (i.e., changeable copy), in which case
the Plan Commission may approve the sign face in its discretion.
(5)
Area of master identification signs.
(a)
MTCCs or planned development under 100,000 square
feet of building area may be permitted one freestanding sign of no
more than 120 square feet in area for primarily retail development
and 100 square feet in area for primarily office or nonretail development.
(b)
MTCCs or planned developments between 100,000
square feet and 500,000 square feet of building area may be permitted
one freestanding sign per arterial street of no more than 120 square
feet in area each, subject to Plan Commission discretion and approval.
(c)
The signage area for MTCCs or planned developments
over 500,000 square feet of building area shall be determined by the
Plan Commission.
(d)
The area of a master identification sign does
not count toward the maximum total signage area allowed, unless otherwise
determined at the discretion of the Planning Commission.
(6)
Master identification signs shall meet open space
requirements, as may be determined by the Plan Commission.
(7)
The Plan Commission shall not approve any master identification
sign greater than 18 feet in height for retail, office, or mixed use,
except for a MTCC or planned development over 500,000 square feet
in building area, which height shall be subject to the discretion
of the Plan Commission considering the factors set forth in Subsections
C(2) and F of this section.
(8)
No freestanding signs other than the master identification sign(s) allowed pursuant to this section, a development identification sign per Subsection G(9) and entrance markers, informational signs, and traffic directional signs without advertising reference and not in excess of four square feet will be permitted for any MTCC or planned development, except as otherwise provided by special exception. If a tenant's name is part of the MTCC or planned development name, the tenant's name may not be repeated elsewhere on the sign, unless otherwise permitted by the Plan Commission in its discretion considering name and sign proportions and other evaluation factors identified in this chapter.
(9)
[1]Unless specifically exempted by the provisions of the master
sign program for the MTCC or planned development, the master identification
sign shall conform to all of the sign code requirements (except for
those governing number and area) for individual sign types found elsewhere
in this chapter.
[1]
Editor's Note: Former Subsection G(9), which stated that the
Common Council may permit a development identification sign, separate
from the master identification sign and lacking tenant reference,
to be placed over or above a private entry drive under certain conditions,
was repealed 8-3-2021 by Ord. No. 2021-2475, which ordinance also redesignated
former Subsection G(10) as G(9).
H.
Authorized special exceptions. In conjunction with
the approval of the master sign program for a MTCC or planned development,
the Plan Commission may authorize limited special exceptions to the
regulations included in this chapter. Such special exceptions will
be permitted only when, in the sole discretion of the Plan Commission,
the applicant demonstrates that they are necessary to provide an improved
comprehensive solution considering the factors and review criteria
as set forth in Subsections C(2) and F of this section and to address
special circumstances and needs that may exist with said MTCC or planned
development. The special exceptions permitted are limited to the following:
(1)
Wall signs: may deviate from the requirement that
wall signs be located with the tenant space or occupancy to which
the signs refer.
(2)
Monument signs: may modify the number of monument
signs, the thirty-foot facade setback requirement, the height limitations
up to the height of the principal building to which the sign pertains,
the proximity to another monument sign, and the sign area limitations
up to the maximum of 150 square feet per sign (as long as the total
permitted sign area for either the occupant or the premises is not
exceeded).
(3)
Tenant identification signs: may deviate from the
size area limitations set forth in this section.
(5)
The total amount of signage permitted under § 210-4C(1)(d) and (e) may be increased by up to 100%.
I.
Temporary signs, window signs, and other devices to
attract attention. Any master sign program approved hereunder may
be modified at any time at the discretion of the City of Franklin
or the Plan Commission to prohibit, further restrict, or place requirements
upon the use of, restrictions on, and standards or requirements for
temporary signs, window signs, interior signs visible to the exterior,
and devices intended primarily to attract attention. This subsection
shall in no way limit any rights or authority the City or Plan Commission
may otherwise have in relation to signs and master sign programs.
[Added 11-20-2007 by Ord. No. 2007-1934]
Signs placed on or affixed to vehicles and/or
trailers, which are parked on a public right-of-way, public property,
or private property so as to be visible from a public right-of-way,
where the apparent purpose is to advertise a product or direct people
to a business or activity located on the same or nearby property,
are prohibited. This provision shall not prohibit signs placed on
or affixed to vehicles and/or trailers, such as lettering on motor
vehicles, where the sign is incidental to the primary use of the vehicle
or trailer.
[Added 5-5-2015 by Ord.
No. 2015-2172]
A.
Purpose of appeals. Sign code variances are intended to allow flexibility
to the sign regulations while still fulfilling the purpose of the
regulations. Nothing in this section, however, is intended to permit
the erection or maintenance of signs which are prohibited in this
chapter.
B.
Duties of Board.
(1)
The Board shall have the power, and it shall be its duty, to hear
and decide administrative appeals where it is alleged there is error
in any order, requirement, decision, initial determination, review
of initial determination, or interpretation made in the enforcement
of this chapter. In exercising this power, the Board may reverse or
affirm, wholly or partly, or may modify the order, requirement, decision
or determination as appealed.
(2)
The Board shall have the power, and it shall be its duty, to hear and decide a request for a variance on all applications of this chapter, including but not limited to relief concerning setbacks. The Board may grant a variance request if the Board finds, in its sole determination, that exceptional circumstances warrant approval of the variance. To establish exceptional circumstances, the Board must find one of the following [Subsection B(2)(a) or (b)]:
(a)
To establish exceptional circumstances, the Board must find
all of the following:
[1]
That the circumstances are not of the applicant's making;
[2]
That the applicant's request mitigates unusual site conditions;
[3]
That the applicant's request would not result in unacceptable
aesthetic characteristics that may depreciate property values or otherwise
create a detriment to the neighborhood;
[4]
That the applicant's request is consistent with the spirit and
intent of this chapter;
[5]
That compliance with this chapter would create a hardship or
be unduly burdensome; and
[6]
There shall be no public harm.
(b)
To establish exceptional circumstances, the Board must find
all of the following:
[1]
That the proposed sign is unique and of exceptional design or
style so as to be aesthetically pleasing and enhance the area;
[2]
That the applicant's request would not result in unacceptable
aesthetic characteristics that may depreciate property values or otherwise
create a detriment to the neighborhood;
[3]
That the applicant's request mitigates unusual site conditions,
if any;
[4]
That the applicant's request is consistent with the spirit and
intent of this chapter; and
[5]
There shall be no public harm, and there shall be public benefit.
C.
Procedures.
(1)
After denial of a sign permit, but not more than 30 days after said denial, an applicant who desires an administrative appeal of an administrative determination, per Subsection B(1) above, may request a hearing before the Board of Zoning and Building Appeals by submitting a written application to the Department of City Development. The request for review shall specify the nature of the appeal. A fee, as may be set forth in § 210-3D of the Municipal Code, shall be required from the applicant at the time that an application for variance is made.
(2)
After denial of a sign permit, but not more than 60 days after said denial, an applicant who desires a variance from any provision or requirement of this chapter may request a hearing before the Board of Zoning and Building Appeals for such a variance by submitting a written application to the Department of City Development. The request for review shall state the reason(s) upon which the person contends that the variance should be granted, which should address circumstances identified in Subsection B(2) above. A fee, as may be set forth in § 210-3D of the Municipal Code, shall be required from the applicant at the time that an application for variance is made.
D.
Standards of review. In addition to factors related to the circumstances identified in Subsection B(2) above, the Board of Zoning and Building Appeals may review such requests for variances utilizing the additional following criteria, applied in its sole determination:
(2)
Site difficulties. Unusual site factors preclude the construction
of a sign in accordance with this chapter which would be reasonably
visible to the roadway adjacent to the site frontage.
(3)
Undue concentration. The sign as proposed will not result in an undue
concentration of signage which renders it difficult or confusing to
read existing signs.
E.
Granting of variance or appeal.
(1)
Should the Board of Zoning and Building Appeals find that an appeal
or variance should be granted, the application will be forwarded to
the Zoning and Building Administrator with directions to issue a permit
in accordance with its decision. If the Board finds that an appeal
or variance should not be granted, it shall cause the applicant to
be informed of the decision and of the reasons for such decision,
in writing, within 10 days of the date of such decision.
(2)
A majority vote of the members present of the Board of Zoning and
Building Appeals shall be necessary to reverse any order, requirement,
decision or determination of the Building Inspector, or to decide
in favor of the applicant on any matter upon which it is required
to pass under this chapter, or to effect any variation in this chapter.
(3)
The Board may impose reasonable conditions to ensure compliance and
to protect nearby or adjacent properties. A violation of such conditions
shall constitute a violation of this chapter.
(4)
The Board may, at its sole discretion, table a matter to a future
meeting(s) in order to obtain additional information prior to reaching
a decision.
(5)
The Board may consider compensating adjustments to location, height,
size, number, or appearance of signs on the site or in the vicinity
and under the control of the applicant as a condition of any variance
granted.