[Adopted 6-7-1971]
As used in this article, the following terms
shall have the meanings indicated:
The latest edition of the American Iron and Steel Institute.
The latest edition of American Water Works Association specifications.
Any person who subdivides land for the purpose of constructing
or causing to be constructed, buildings for which provisions are required
to be made for water supply.
The boundary line of a public highway, street, alley or easement
controlled by the Village.
The duly appointed Public Works Administrator of the Village
of Cazenovia, New York.
[Added 4-3-2000 by L.L. No. 1-2000]
The line connecting the water main within the public right-of-way
of the Village to the property line.
A pipe or conduit used for carrying sewage.
The Village of Cazenovia, New York.
The duly appointed Village Engineer of the Village of Cazenovia,
New York, or a consulting professional engineer retained for such
purposes by the Village of Cazenovia. If none, it shall mean the Village
Water Superintendent.
The following specifications for water mains,
gate valves, fire hydrants, service connections and disinfection are
to be the minimum acceptable standards for any proposed construction
of water facilities that are to connect to, or become a part of, the
Village of Cazenovia water supply system.
A.
Pipe materials.
[Amended 4-3-2000 by L.L. No. 1-2000; 1-5-2012 by L.L. No.
1-2012]
(1)
Except as provided in Subsection A(2) below, all water mains shall consist of a minimum of six-inch diameter ductile iron pipe. All ductile iron pipe shall be manufactured in accordance with A.W.W.A. specifications, and shall have a minimum thickness class of 52. All pipe joints for ductile iron pipe shall be manufactured in accordance with A.W.W.A. specifications, and shall be of the Tyton type or mechanical joint type. All Tyton-type joints shall have two brass wedges installed at each joint.
(2)
In lieu of the use of ductile iron pipe for water
mains, PVC SDR 18 meeting A.W.W.A. C900 or HDPE may be used when approved
by the Village Public Works Administrator. The PVC pipe shall be joined
by preformed confined rubber gasket joints designed for the pressure
expected to be experienced in the installation. A request for use
of the PVC pipe alternate shall include details assuring compatibility
with existing water facilities, especially connections, fittings and
service connections. When installed, the pipe shall be buried with
metal-faced plastic tape and such other devices as may be specified
by the Village Public Works Administrator to permit pipe location
with magnetic-type metal detectors. Use of PVC pipe where approved
shall comply in all aspects of installation with the requirements
of this article.
B.
Water main fittings. All ductile iron pipe fittings
shall be manufactured in accordance with A.W.W.A. specifications.
Joints for ductile iron fittings shall be of the mechanical joint
type and shall be manufactured in conformance with A.W.W.A specifications.
[Amended 4-3-2000 by L.L. No. 1-2000]
C.
Pipe installation.
(1)
Except as otherwise specified, ductile iron pipelines
shall be installed in accordance with A.W.W.A. specification C-600.
Care shall be taken during loading, transportation, unloading and
installing to prevent damage to the pipe or coating. All pipe and
fittings shall be carefully examined before installing, and no piece
shall be installed which is found to be defective. Any damage to the
pipe, fittings or coatings shall be repaired as directed by the Village
Engineer, Public Works Administrator or their duly authorized representative.
[Amended 4-3-2000 by L.L. No. 1-2000]
(2)
If any defective pipe or fittings are discovered after
installation, they shall be removed and replaced with sound pipe and
fittings or shall be repaired by the contractor in an approved manner
and at his own expense. All pipe and fittings shall be thoroughly
cleaned before installation, shall be kept clean until they are used
in the completed work and, when installed, shall conform to the line
and grades approved by the Village Engineer, Public Works Administrator
or their duly authorized representative. There shall be a minimum
of 4.5 feet of cover, from the top of the water main to the finish
grade.
[Amended 4-3-2000 by L.L. No. 1-2000]
(3)
Pipes shall be installed with full support the entire
length. Blocking of pipe installed in the ground will not be permitted
unless the pipe is to be laid with a concrete cradle or encasement.
All bedding conditions for the pipe shall be approved by the Village
Engineer, Public Works Administrator or their duly authorized representative.
Open ends of pipe shall be kept plugged with a watertight bulkhead
during construction. Sufficient selected backfill shall be placed
or other precautions shall be taken to prevent flotation movement
or damage to the pipe fittings and coatings.
[Amended 4-3-2000 by L.L. No. 1-2000]
(4)
Whenever pipes require cutting to fit into other lines,
the work shall be done with approved cutting tools specifically designed
to cut pipe, so as to leave a smooth end at right angles to the axis
of the pipe.
(5)
Water mains shall not be placed in the same trench
as a sewer line or sewer lateral.
D.
Anchors and tie rods.
(1)
Concrete backing and/or tie rods and concrete anchors
shall be provided at all tees, crosses, bends, plugs and valves or
as directed by the Village Engineer, Public Works Administrator or
their duly authorized representative.
[Amended 4-3-2000 by L.L. No. 1-2000]
(2)
Tie rods installed in the ground or in contact with
water shall be of A.I.S.I. type 501 or 502 stainless steel or approved
higher alloy.
E.
Testing.
(1)
All pipes shall be tested hydrostatically for 15 minutes
at a pressure 50% in excess of the pressures to which the pipe will
normally be subjected, but in no case less than 150 pounds per square
inch (psi). Any obvious leaks or ruptured piping disclosed by the
tests shall be repaired or replaced and the test repeated to the satisfaction
of the Village Engineer, Public Works Administrator or their duly
authorized representative.
[Amended 4-3-2000 by L.L. No. 1-2000]
(2)
All pipe lines shall then be tested hydrostatically
for leakage for one hour at a pressure equal to the maximum rate of
pressure of the section of line under test, but in no case less than
100 pounds per square inch (psi). The rate of leakage shall not exceed
25 gallons per mile of pipe per 24 hours per inch of nominal pipe
diameter. Any leaks or defective pipe disclosed by the leakage test
shall be repaired or replaced, and the aforementioned leakage test
repeated as often as necessary until the leakage requirement is met.
(3)
The developer shall accomplish the required tests
on the pipeline by individually testing each component section of
main designated by the Village Engineer, Public Works Administrator
or their duly authorized representative. All water for tests shall
be furnished and disposed of by the developer at his own expense.
Source and/or quality of water which the developer proposes to use
in testing the lines shall be approved by the Village Engineer, Public
Works Administrator or their duly authorized representative.
[Amended 4-3-2000 by L.L. No. 1-2000]
F.
Sterilization.
(1)
All pipe and fittings connected to and forming a part
of the potable water supply shall be sterilized in a manner acceptable
to the Village Engineer, Public Works Administrator or their duly
authorized representative. Sterilization shall be accomplished after
the pipe has passed the hydrostatic tests. The method proposed by
the contractor shall be in full accordance with the requirements of
the New York State Department of Health and shall be acceptable to
the Village Engineer, Public Works Administrator or their duly authorized
representative.
[Amended 4-3-2000 by L.L. No. 1-2000]
(2)
All new piping shall be filled with not less than
25 nor more than 50 parts per million (ppm) of available chlorine
and held in contact for not less than 24 hours. Final tests after
24 hours contact time shall show a minimum residual chlorine content
of 10 ppm in all parts of the system.
(3)
Sterilization tests shall be repeated as often as
necessary, and as directed by the engineer and/or the New York State
Department of Health until the minimum residual chlorine content of
10 ppm has been reached. The chlorine solution shall be thoroughly
flushed out prior to placing the new sections of the main in service.
The developer is cautioned that the spent chlorine solution must be
disposed of in such a way as not to be detrimental to animal, plant
or fish life.
A.
General. Gate valves shall be located at each street
intersection in such a manner that each block of each street can be
isolated from the system by closing no more than two valves. Valves
shall be placed so that the distance between valves will not exceed
1,000 feet.
B.
Valve construction. Gate valves shall conform to A.W.W.A.
specifications and shall have a cast or ductile iron body fully bronze
mounted and shall be mechanical joint, resilient seat type. Valves
shall be of the O-ring seal nonrising stem type with two-inch operating
nuts and shall open counterclockwise. The valves shall be of the same
manufacturer as the Village has adopted as a standard unless otherwise
approved by the Village Engineer, Public Works Administrator or their
duly authorized representative. The gate valves shall be designed
for 175 pounds per square inch working pressure and tested to 300
pounds per square inch.
[Amended 4-3-2000 by L.L. No. 1-2000]
C.
Installation. All gate valves shall be installed in
a vertical position perpendicular to the center line of the water
main. Gate valves shall be supported on a concrete pad two feet by
two feet by one foot thick and shall be secured to the supporting
pad by two three-eighths-inch diameter steel rods embedded in the
concrete.
D.
Valve boxes. All valves installed underground shall
be equipped with cast iron valve boxes. The valve boxes shall be of
a recognized manufacturer and shall be the adjustable type with a
barrel not less than five inches in diameter and a base to fit the
valve bonnet on which it is to be installed. The word "WATER" shall
be cast in the cover. The direction of the opening of the valves shall
be indicated thereon by means of an arrow.
A.
Manufacturer.
(1)
Fire hydrants shall conform to A.W.W.A. specifications
and shall be of the type standardized by the Village. All hydrants
shall have one four-inch pumper outlet and two two-and-one-half-inch
hose outlets. All hydrant valve openings shall be not less than 4 1/2
inches.
[Amended 4-3-2000 by L.L. No. 1-2000]
(2)
Hydrants shall be of the break away type such that
when the barrel of the hydrant is broken off the hydrants will remain
closed.
(3)
Hose and pumper outlet threads shall be national standard.
All hydrants shall open counterclockwise and the direction of the
opening shall be indicated by means of an arrow and appropriate wording
cast in the top of the hydrant.
B.
Installation.
(1)
Hydrants shall be set plumb with the pumper outlet
facing the roadway. The hydrant shall be installed with the inlet
piping buried up to a minimum depth of cover of 4.5 feet. The distance
from the center line of the pumper nozzle to the finished grade shall
be a minimum of 18 inches and a maximum of 24 inches. A minimum of
two cubic feet of clean gravel shall be placed under the fire hydrant
to allow for drainage after use. The distance between hydrants is
to be no more than 600 feet.
[Amended 4-3-2000 by L.L. No. 1-2000]
(2)
Hydrants shall be thoroughly blocked with concrete
or shall be harnessed to the six-inch hydrant branch valve. The distance
from the center of the hydrant to the center of the hydrant branch
gate valve shall be a minimum of 30 inches.
C.
Painting. The exterior aboveground portion of the
hydrant shall be field painted. The color and type of paint shall
be that adopted by the Village as a standard.
[Added 6-2-1980 by L.L. No. 4-1980]
A.
It shall be unlawful for the owner of property or
the user of Village water or both to introduce or permit the introduction
into the Village water supply system of pollution or contamination
of any kind. Whenever cross-connection to other water supply into
the Village system is found or whenever any other condition is found
which presents the possibility of contamination or pollution, the
water supply to such premises and/or other premises from which cross-connection
is made shall be discontinued immediately until the cross-connection
is eliminated or the condition remedied. The Water Superintendent
may permit or require a backflow preventer of pattern and design which
the New York Department of Health approves as reasonably adequate
to prevent contamination, if the Superintendent determines that physical
separation from the Village water system is not practicable or necessary,
or that adequate inspection for cross-connection cannot readily be
made, or that such backflow preventer is necessary because of existing
or possible backflow resulting from special condition or use or equipment.
B.
Any corrective measure, disconnection or change on
private property shall be at the sole expense of the owner of such
property. Any changes required in the Village system outside the property
or between the meter and the supply line or distribution system and
any charges for cutoff or disconnection shall be added to the charges
for water against the premises necessitating such expenditure.
C.
All physical connections which may constitute potential
cross-connection are prohibited unless constructed, maintained and
operated in accordance with the provision of the State of New York
Sanitary Code for potable (drinking) water.
D.
Anyone in violation of this article shall be subject
to a fine for each violation thereof, not to exceed the sum of $250
and/or imprisonment for not more than 15 days, or both such fine and
imprisonment.
[Amended 4-3-2000 by L.L. No. 1-2000]
E.
Any person, except a fireman while on duty for the
use of the Fire Department, opening or tampering with any Village
hydrant, valve or stop cock, without the written consent of the Board,
shall be subject to a penalty.
F.
In the interest of public health, the Village's mains
or service shall not be connected on any premises with any service
pipe or piping which is connected with any other source of water supply
not approved by the Department of Health of the State of New York;
nor shall the Village's mains or service pipes be connected in any
way to any piping, tank, vat, or other apparatus which contains liquids,
chemicals, or any other matter which may flow back into the Village's
service pipe or mains and consequently endanger the water supply.
G.
The Village shall use reasonable care and diligence
to provide a constant supply of water at a reasonable pressure to
customers, but reserves the right, at any time, without notice, to
shut off the water in its mains for the purpose of making repairs
and extensions, and for other purposes.
H.
The Village shall not be liable for a deficiency or
failure in the supply of water or the pressure thereof for any cause
whatsoever, nor for any damage caused thereby, or by the bursting
or breaking of any main or service pipe or attachment to the Village's
property. All customers having installations upon their premises depending
upon the pressure in the Village's pipes to keep them supplied are
cautioned against danger of collapse, and all such damages shall be
borne exclusively by the customers.
A.
General.
[Amended 4-3-2000 by L.L.
No. 1-2000; 3-7-2016 by L.L. No. 2-2016]
(1)
Service pipes shall be of Type K copper tubing with a minimum diameter
of three-fourths inch and conform to AWWA specification C800. An eight-inch
radius loop shall be provided at the pipe at the connection of the
service pipe to the main to provide flexibility. All service pipes
shall have a brass corporation stop located in the main and brass
inverted key curb stop and drain with cast iron curb box at the property
line. All joints in service pipes shall be of the flare or compression
type. In lieu of copper, for lines larger than one inch in diameter,
polyethylene meeting specification ANSI/AWWA C901, Polyethylene (PE)
Pressure Pipe and Tubing, One Inch through Three Inches, for Water
Service, may be used providing a meter pit is installed in the right-of-way
and is supplied by a copper or ductile line to this meter pit.
(2)
All service connections to the main water line shall be made in the
upper quadrant of the water line. Minimum cover over the top of the
service pipe shall be 4.5 feet.
(3)
All service lines must have both a corporation stop and a curb stop.
Service lines for fire suppression systems shall consist of a separate
service line tapped directly to the main with its own corporation
stop and curb stop. Fire suppression system water may not be drawn
from the domestic water service line serving the premises.
B.
Testing and sterilization. Testing and sterilization shall be accomplished in accordance with § 174-25E and F as previously outlined.[1]
[1]
Editor's Note: Former Subsection C, regarding
interference with meters and hydrants, added 4-3-1995 by L.L. No.
1-1995, which immediately followed this subsection, was deleted 4-3-2000
by L.L. No. 1-2000.