The purpose of establishing architectural standards is to set
minimum standards for the appearance and quality of buildings and
corresponding site elements that are recognized as enhancing property
values and are in the interest of the general welfare of the city.
Given that the City of Celina is an area designated with historical,
cultural, and architectural importance and significance, the following
provisions apply. These standards are not intended to prohibit architectural
innovation, nor are they intended to mandate specific architectural
styles and concepts. Rather, they are intended to provide for developments
of enduring quality that provide visual character and interest. The
development community is encouraged to seek out new and innovative
construction techniques and materials to implement the standards contained
herein that will result in a significant contribution to the visual
character of the area and the city as a whole. Any new or innovative
material shall be considered on a case-by-case basis by the director
and must be equal to or exceed the current standards in terms of quality
and longevity.
(Ordinance 2019-42 adopted 10/8/19)
(a) The regulations provided in this section shall apply to all new construction
and all structures within all zoning districts, but shall only apply
to single-family residential uses when indicated. Where the regulations
of this section conflict with other sections or provisions of this
chapter, the mores specific regulations shall apply.
(b) Single-family tracts with existing PDs (or comparable special zoning)
which include specific architectural standards may continue to apply
the standards as found in the governing PD. Non-residential tracts
and uses within existing PDs (or comparable special zoning) shall
be governed by the standards contained herein.
(c) When an existing building, constructed prior to the adoption of this
section, is proposed for an addition or expansion that will increase
the square footage of the existing building by less than fifty percent
(50%), either by a single expansion or by the cumulative effect of
a series of expansions, similar or like exterior materials may be
used on new facades that match the existing building and architectural
theme to the extent possible.
(d) Any addition that is fifty percent (50%) or greater of the originally
approved floor area shall be subject to and shall comply with the
regulations herein, potentially resulting in the reconstruction of
the entire exterior veneer of an existing structure. At a minimum,
the front facade must comply with the regulations stated herein.
(e) Certain structures, such as temporary construction buildings or portable
classroom buildings situated on public school or non-profit property,
may be exempt from compliance.
(f) The provisions of this section shall be administered by the director
of development services who shall have the authority to approve any
facade plan that is deemed to satisfy the minimum requirements of
this section, alternate facade plans deemed to meet the intent of
the section, including any minor deviations or waivers, and to make
necessary interpretations regarding any subjectivity or frustration
of purpose contained herein.
(g) All exterior facades shall be perpetually maintained and repaired
in a safe, reasonably sound, and attractive manner by the owner in
a manner that protects against the elements, is structurally safe,
and corrects any visual deficiencies or other problems.
(h) The city council may grant a specific use permit (SUP), establish
a planned development (PD) district or enter into a development agreement
or other economic incentive agreement, which may amend or revise the
regulations herein for a certain project or area of the city.
(i) Due to the unique service nature of government owned and occupied
facilities, in addition to the development costs being a public burden,
such facilities may meet the spirit and intent of the regulations
contained herein to the extent possible, and are not expected to strictly
comply.
(j) The city council may, from time to time, amend, supplement, or change
the boundaries of a district or the regulations herein established
as provided by state law or establish special zoning districts or
overlay districts that may have substantially different exterior material
requirements.
(Ordinance 2019-42 adopted 10/8/19)
(a) Submittal information.
Sufficient information shall
be submitted to evaluate the architectural standards criteria outlined
herein as part of the site plan submittal.
(b) Elevations.
Applications that includes a site plan shall
include the following:
(1) Color renderings of all facades of each building.
(2) Proposed exterior materials with a percentage breakdown of each material
used, exclusive of windows and doors.
(3) A calculation chart or graphic exhibit demonstrating compliance with
the articulation standards.
(4) A listing of the selected auxiliary design standards, described herein,
to illustrate compliance.
(5) If a landmark feature is required of the building, please note the
feature proposed for credit.
(6) The director may require sample boards.
(c) Streetscape elements.
For any proposed streetscape elements
(such as bike racks, trash receptacles, lampposts, tree grates, bollards,
outdoor seating, etc.) or screening devices (masonry walls screening
dumpsters, mechanical equipment, etc.), graphics shall also be submitted
showing the material, color, height, and any other pertinent details
of the elements proposed.
(Ordinance 2019-42 adopted 10/8/19)
Architectural concrete masonry units (CMU)
includes highly textured finish, such as split faced, indented,
hammered, fluted, ribbed, burnished, or similar decorative finish;
coloration shall be integral to the masonry material and shall not
be painted on; minimum thickness of one inch when applied as a veneer;
and shall include light weight and featherweight decorative masonry
units.
Big box
shall mean a building, usually with a single tenant, which
comprises more than 50,000 square feet.
Brick
includes severe weather rated kiln-fired clay or slate material,
can include concrete brick if it is to the same ASTM C216 or C652
standard and severe weather rated as typical fired clay brick; minimum
thickness of one inch when applied as a veneer, and shall not include
underfired clay, sand, or shale.
Director
shall mean the director of development services, or his designee.
EIFS
means exterior insulation and finish systems.
Engineered wood
shall mean a wood-based product that has been treated to
be stronger and more weather/wear resistant than natural wood.
Facades.
(a)
Front facade
shall mean the exterior walls of any enclosed space that
are parallel or roughly parallel to the street.
(b)
Rear facade
shall mean the exterior walls of any enclosed space that
are parallel or roughly parallel to the rear property line.
(c)
Primary facade
shall mean the exterior walls of any enclosed space that
face directly on a public street of any size, back to a public street
that is designated as a collector or larger, along any active storefront
regardless of orientation, or may be so defined at the discretion
of the director.
(d)
Secondary facade
shall mean the exterior walls of any enclosed space that
do not directly face a public street or back to a public street that
is designated as a collector or larger (i.e. any wall other than a
primary facade).
Masonry materials
shall mean and include that form of construction defined
below and composed of brick, stone, granite, marble, stucco (three-step
hard coat), decorative concrete masonry unit, tilt wall concrete panels,
sealed and painted concrete block, and exterior insulation finish
systems (EIFS), and rock or other materials of equal characteristics
laid up unit upon unit set and bonded to one another in mortar.
Non-residential building
shall mean those buildings utilized for use other than single-family,
duplex, and townhome dwelling, to specifically include commercial,
retail, medical, office, and multifamily structures and associated
accessory structures.
Residential buildings
shall mean those buildings utilized for a single-family,
duplex, and townhome dwellings.
Stone
includes naturally occurring granite, marble, limestone,
slate, river rock, and other similar hard and durable all-weather
stone that is customarily used in exterior building construction;
may also include cast or manufactured stone product, provided that
such product yields a highly textured stone-like appearance, its coloration
is integral to the masonry material and shall not be painted on, and
it is demonstrated to be highly durable and maintenance free; natural
or manmade stone shall have a minimum thickness of one inch when applied
as a veneer.
Shake shingles
mean a non-combustible, fire-rated product that is used as
a decorative element on residences.
Stucco
means the 3-step stucco process that is applied in three
separate layers: 3/8-inch thick scratch coat, 3/8-inch thick brown
coat, and approximate 1/8-inch thick finish coat. The approximately
7/8-inch three-coat system is applied over an approved weather-resistive
barrier and metal lath either by hand using a trowel or by machine
application. Any stucco product that does not meet the stated requirements
is not allowed.
(Ordinance 2019-42 adopted 10/8/19)
(a) Category A
materials are defined as the superior masonry
products from which the city prefers buildings to be predominantly
constructed. Unless otherwise provided for in this chapter, acceptable
category A masonry finishing materials are kiln-fired brick, natural
stone, and manufactured stone.
(b) Category B
materials are the secondary products that
the city recognizes as materials acceptable for use, products that
should not be the predominant material for a building and are considered
as somewhat less desirable than those materials listed in category
a. Unless otherwise provided for in this chapter, acceptable category
B masonry finishing materials include three-step stucco, architectural
concrete block with integrated color (i.e. split-face CMU), concrete
tilt wall (colored or stamped), treated engineered wood, and cementitious
fiberboard with integrated color (in the form of lap siding or board
and batten).
(c) Category C
materials are accent products acceptable
in limited application for architectural accents and for walls on
upper stories of multi-story buildings. Unless otherwise provided
for in this chapter, acceptable category C materials include metal,
tile, glass block, exterior insulation and finish systems (EIFS),
and natural wood products.
(d) Prohibited exterior surface materials include cinder block, vinyl,
plastic, and aggregate pea-gravel finished surfaces.
(Ordinance 2019-42 adopted 10/8/19)
(a) Building color.
(1) The dominant color of all buildings shall be muted shades of color
that are subtle, neutral, or earth tone. Black and stark white shall
not be used except as accent colors or as found within brick and stone.
The color of secondary facades shall match or compliment the primary
facade.
(2) There are no restrictions on accent colors that comprise less than
one percent (1%) of the building face, except that no high intensity
colors, neon colors, or fluorescent colors shall be used.
(3) Bright, reflective, pure tone primary or secondary colors are permissible
only in limited application as accent colors on canopies and awnings,
or other such features. Proportions should be consistent with trim
or accentuation only. Such building trim and accent areas shall not
exceed five percent (5%) of any single exterior wall area. Specifically
excluded are door and window frames, moldings, cornices, and other
such features. This provision shall not be construed as a license
to employ corporate imaging or branding on the primary building facade.
(4) The use of tube lighting, string lights, or other similar materials shall not be installed on non-residential buildings, as described in article
14.04, part five, lighting standards.
(5) No more than one (1) color shall be used for visible roof surfaces;
however, if more than one type of roofing material is used, the materials
shall be varying hues of the same color or complimentary in nature.
Awnings and canopies may incorporate brighter color and branding;
however, the primary roof shall not be a bold color.
(b) Repairs and alterations.
All repair and alterations
of exterior facades, including re-painting or rebranding, of non-residential
buildings are required to obtain a permit from the city and comply
with all applicable color regulations contained herein.
(Ordinance 2019-42 adopted 10/8/19)
(a) Design standards for residential development.
All new
residences within the city shall conform to the following design standards:
(1) Category A materials for single-family detached and single-family
attached development.
Residential structures shall be
constructed of a minimum of eighty percent (80%) masonry, defined
for single-family structures as brick, stone, or manufactured stone.
(2) Category B materials for single-family detached and single-family
attached development.
The remainder may include one or
more of the following: three-step stucco, treated engineered wood,
and shake shingles. Any of these materials may be used singly or in
combination, not to exceed a total of twenty percent (20%). Other
materials of equal or similar characteristics may be allowed at the
discretion of the director. On lots greater than one-half (1/2) acre
in size, cedar or redwood planking may be allowed at the discretion
of the director.
(3) Category C materials for single-family detached and single-single-family
attached development.
Cementitious fiberboard or natural
wood may also be used for architectural features, including window
box-outs, bay windows, roof dormers, columns, chimneys not part of
an exterior wall, or other architectural accent features, as approved
by the director.
(4) Minimum masonry on front facade.
Notwithstanding the
above overall percentages required for single-family detached and
single-family attached development, the front facade shall be a minimum
of eighty percent (80%) masonry.
ARTICLE 14.04, TABLE 1 Required Percentages of Exterior Materials
for Single-Family, Both Attached and Detached
|
---|
Facades
|
Percentage Breakdown
|
Definition
|
---|
All facades when considered together
|
Minimum 80% category A
Maximum 20% category B
|
All walls, when counted together, whether visible from the street
or not, shall add up to the 85/15 rule.
|
|
Category C
|
May only used for minor architectural features (see subsection (3), above)
|
Front facade
|
Minimum 80% category A
|
|
Decorative Features1
|
Up to 5%
|
|
Note 1. Treated engineered wood or EIFS may be used for trim
or soffit construction - the percentage of treated engineered wood
or EIFS must be subtracted from the percentage of other category materials
so that the total percentage of any given facade remains as shown
above.
|
(5) Placement of exterior materials.
Notwithstanding the
minimum and maximum percentages of building materials allowed on residential
homes (shown above), any break from one material to another shall
follow the natural lines and design features of the architectural
plan. A change from one material to another cannot be arbitrarily
assigned without consideration of the specific facade for which it
is designed. The director of development services shall have final
approval of any residential elevation submitted for construction.
(6) Alternate stucco architecture.
If a home is designed
with a specific architectural style that warrants the use of stucco
as the primary exterior material, including but not limited to Mediterranean,
Spanish, Southwest, or Modern, then the use of stucco as the primary
or exclusive material may be approved by the director in lieu of other
exterior material standards. All elements of the architectural style
must be incorporated, including but not limited to clay roof tiles,
typical of the style. Residences with primarily stucco finishes shall
be accented with heavy wood beams, stonework, or other features to
enhance the style. Elevations with no discernable style that simply
disregard the required masonry requirement will not be considered.
Only three-step stucco (or its equivalent) is allowed.
(7) Elevation repetition.
Any house elevation shall not
be repeated on the lot most directly across the street, nor shall
it be repeated on two (2) lots in either direction on the same side
of the street. A wide variety of elevations is desired as it strengthens
the character of the subdivision and reduces monotony of design. When
stucco homes are the predominant exterior material used on a particular
street, variations of color and design are required to minimize visual
monotony.
(8) Elevation masonry mix and pattern.
Front elevations
shall use more than one type of masonry product in a variety of patterns
to vary the architectural appeal of the streetscape. Regardless of
the minimum category A masonry requirements, every front facade shall
be a mixture of materials and colors.
(9) Front facades and front-facing garage placement - one-story homes.
The face of garage doors shall not extend beyond the front facade
of any residential structure unless one or both of the following conditions
apply; and in that case, the face of the garage door may extend up
to a maximum of eight (8) feet beyond the front facade:
(A) A front porch extending a minimum of fifty percent (50%) of the front
facade is provided; or
(B) A bay window is provided on the longest wall face of the front facade.
(10) Front facades and front-facing garage placement - two story homes.
The face of garage doors may extend beyond the front facade
of any residential structure up to a maximum of eight (8) feet beyond
the front facade. Any additional garages to be provided must be placed
with side (J-swing) or rear access.
(11) Front facades and J-swing garage placement.
When the
doors of garages are designed to be perpendicular to the street access
(i.e. J-swing garages), the garage may extend into the front setback
of the residential structure, as per the director.
(12) Front entry doors.
Front entry doors shall consist of
a hardwood, treated engineered wood, or other highly durable products,
including products that have a wood appearance and are approved by
the director.
(13) Garage doors.
Front entry doors shall consist of lightweight
but durable materials, such as painted metal, and include materials
that have a wood appearance and are approved by the director. Garage
doors windows are permitted.
(14) Roof pitch.
Minimum roof pitch of residential structures
is 6:12.
(15) Roof materials.
All roof materials shall meet the minimum
standards as listed in the adopted International Building Code, which
includes the use of solid solar shingles and panels.
(16) Screening of utility units.
HVAC units shall be screened
from view from streets with shrubs or a stained wood fence.
(17) Mailboxes on individual lots.
The subdivision will determine
whether individual mailboxes shall be brick or stone to match the
residence or decorative metal containers on posts. Where practical,
the mailboxes should be paired for ease of delivery.
(18) Mailboxes that are clustered.
When mailboxes are clustered
in single-family or two-family residential districts, the exterior
of the clustered mailboxes shall be decorative metal on a matching
support poles and shall be maintained by the homeowners association
(HOA).
(19) Driveways.
All driveways shall be concrete and have
a minimum width of ten (10) feet and may match the width at the garage
door at the property line.
(b) Architectural features.
All residential structures must
include at least four (4) of the following design features on the
front facade or visible from the front or side street:
(1) Garage doors not facing the street (J-swing garage style);
(2) Carriage style garage doors with decorative hardware;
(3) Decorative brick patterning;
(4) Architectural pillars or posts;
(5) Bay window facing street;
(6) Brick or stone chimney on exterior wall;
(8) Covered front porches (minimum of sixty (60) square feet covered
by main roof or an architectural extension);
(11) Roof accent upgrades (e.g. metal, tile, slate, solar tiles);
(12) Recessed entries a minimum of three (3) feet deeper than main front
facade;
(13) Greater than 8:12 primary roof pitch, or variable roof pitches;
(18) Coach lights at entrances;
(19) Decorative attic or gable feature, minimum two (2) square feet in
size (e.g. vent, window, brick detail);
(20) Decorative driveway paving (e.g. salt finish, exposed aggregate,
or other treatments approved by the city building official).
(Ordinance 2019-42 adopted 10/8/19)
(a) Exterior materials for multifamily construction.
Article 14.04, Table 2A Exterior Materials for Multifamily
|
---|
Categories
|
Materials
|
---|
A
|
Brick, Stone, or Manufactured Stone
|
B
|
Split-Face CMU, Stucco, Cementitious Fiber Board, Treated Engineered
Wood1
|
C
|
Metal, Natural Wood, Tile, Glass, EIFS
|
Prohibited
|
Plain Concrete Block, Aggregate, Vinyl, Plastic, Tilt Wall2
|
Article 14.04, Table 2B Required Percentages of Exterior Materials for Multifamily
|
---|
Facades
|
Percentage Breakdown
|
Definition
|
---|
Primary
|
80% Category A
20% Category B*
0% Category C*
|
Exterior walls of buildings which face a street or parking area
|
Secondary
|
50% Category A
50% Category B*
0% Category C*
|
Exterior walls of buildings which are NOT clearly visible from
a public street, such as an interior courtyard
|
Note 1. Treated engineered wood or EIFS may be used for trim
or soffit construction - the percentage of treated engineered wood
or EIFS must be subtracted from the percentage of other category materials
so that the total percentage of any given facade remains as stated
above.
|
Note 2. Tilt wall is prohibited as an exterior material for
multifamily structures.
|
(b) Design standards for multifamily construction.
(1) Primary facades.
Exterior facades that face a public
street, parking lot, or fire lane shall be constructed of eighty percent
(80%) masonry category A products.
(2) Secondary facades.
Facades that do not face a public
street or parking lot (such as an interior courtyard) shall be constructed
of a minimum of fifty percent (50%) masonry category A products with
the remainder being one or more category B materials.
(3) Two masonry materials required.
At least two (2) masonry
materials shall be used on all exterior facades.
(4) Uniform architectural style.
All buildings within a
common development, as shown on a development plan, conceptual plan,
or site plan, shall have similar architectural styles, materials,
colors and detailing; however, sufficient variations should be incorporated
to discourage exact duplicate buildings.
(5) Facades adjacent to streets.
Facades shall generally
be built parallel to the street frontage.
(6) Facades adjacent to single-family.
Facades shall generally
be built perpendicular when adjacent to single-family districts unless
set back a minimum of 100 feet from single-family property lines.
(7) Accessory building materials.
Amenity centers, covered
garages, and other accessory buildings shall meet the exterior material
requirements of the primary facades. Carports shall meet the exterior
material requirements of the primary facades with the exception of
the support poles, which may be constructed of painted metal.
(8) Amenities and hardscape.
All streetscape elements and
site amenities, such as bike racks, trash receptacles, lampposts,
and tree grates shall be metal, rust and flake/chip resistant, and
generally be black in color. Bollards may be concrete or cast metal
and shall be of decorative design.
(9) Roof design.
Roofs shall be peaked with either hip,
gable or mansard design with a minimum one-to-four (1:4) pitch, or
a parapet wall or false mansard design with a minimum one-to-two (1:2)
pitch is acceptable only if constructed around the entire perimeter
of a building so that no flat roof shall be visible from a public
street.
(10) Roof materials.
Any accessory structure (such as a garage,
carport, or amenity center) within a multifamily development shall
have a decorative metal roof or a parapet wall to shield roof-mounted
equipment.
(c) Architectural features.
All multifamily primary buildings
shall be designed to incorporate no less than four (4) of the architectural
features from the list below.
(1) Canopies, awnings, porticos with colonnade or arcades.
(2) Raised pilaster cornices (end columns at corners), or quoined corners
(any of various bricks of standard shape for forming corners of brick
walls or a wedge-shaped piece of wood, stone, or other material, used
for various ornamental purposes at corners).
(3) Vertical elements (tower, cupola, lighthouse, turret, arches, etc.).
(4) Accented windows and doors framed with smooth cobblestone, cast stone,
limestone, or other decorative masonry headers and sills, or dormer
windows.
(5) Outdoor patios and/or courtyards (landscaped and furnished) integrated
into a site’s layout that creates a sense of place for informal
and experiential gathering.
(6) Decorative and repetitive ornamentation (non-signage) integrated
into the building facade, such as corbels, medallions, functioning
clocks, niches, wrought iron, balconettes, gargoyles, or rhythm patterned
brickwork.
(7) Other similar architectural features, as approved by the director.
(Ordinance 2019-42 adopted 10/8/19)
(a) Exterior standards for non-residential structures.
(1) Two masonry materials required.
At least two (2) masonry
materials shall be used on all exterior facades. See tables 3A, 3B,
3C, 4A, and 4B for masonry requirements.
(2) Windows.
Windows and glazing shall be limited to a minimum
of ten percent (10%) and maximum of seventy percent (70%) of each
building elevation facing a street, major access drive, or side yard
greater than ten (10) feet. Faux windows (i.e. non-transparent architectural
features meant to appear as a window opening) are allowed along secondary
facades, and big boxes may utilize other rhythmic material options
to achieve the window appearance.
(3) Roof designs and materials.
For buildings with a visible
hip, gable, or mansard roof, allowed materials include metal (standing
seam), slate or tile (clay or cement, barrel, or Roman-shaped).
(4) Prohibited materials.
Prohibited exterior surface materials
include cinder block, vinyl, plastic, and aggregate pea-gravel finished
surfaces.
(5) Murals.
Murals, if used, cannot display or connote a
commercial message without abiding by the sign regulations, as found
within the Code of Ordinances.
(6) Roof design.
Roofs shall be peaked with either hip,
gable, or mansard design with a minimum one-to-four (1:4) pitch, or
a parapet wall or false mansard design with a minimum one-to-two (1:2)
pitch is acceptable only if constructed around the entire perimeter
of a building so that no flat roof shall be visible from a public
street or along an active storefront.
(b) Landmark buildings.
(1) Buildings that are located at the end of a terminating street or
major access lane or at the intersection of streets and/or major access
lane shall be considered a landmark building.
(2) Such buildings shall be designed with landmark features that take
advantage of that location, such as an accentuated entry and a unique
building articulation that is offset from the front wall planes and
extends above the main building eave or parapet line.
(3) Landmark features shall be in proportion to the building, subject
to review and approval by the director.
(c) Architectural features for non-residential structures.
All non-residential structures shall be designed to incorporate no
less than four (4) of the architectural features from the list below.
Buildings over 50,000 square feet must include a minimum of five (5)
of the referenced architectural features.
(1) Canopies, awnings, porticos with colonnade or arcades.
(2) Raised pilaster cornices (end columns at corners), or quoined corners
(any of various bricks of standard shape for forming corners of brick
walls or a wedge-shaped piece of wood, stone, or other material, used
for various ornamental purposes at corners).
(3) Vertical elements (tower, cupola, lighthouse, turret, arches, etc.).
(4) Accented windows and doors framed with smooth cobble, cast stone,
limestone or other decorative masonry headers and sills, or dormer
windows.
(5) Outdoor patios and/or courtyards (landscaped and furnished) integrated
into a site’s layout that creates a sense of place for informal
and experiential gathering.
(6) Decorative and repetitive ornamentation (non-signage) integrated
into the building facade, such as corbels, medallions, functioning
clocks, niches, wrought iron, balconettes, gargoyles, or horizontal
and rhythm patterned brickwork.
(7) Other similar architectural features, as approved by the director.
(d) Building articulation standards for non-residential structures.
Primary facades clearly visible from a public street or along
an active storefront shall meet the following minimum standards for
articulation:
(1) Horizontal articulation.
No building wall shall extend
for a distance equal to three times the wall’s height without
providing an offset equal to fifteen percent (15%) of the wall’s
height, and that new plane shall extend for a distance equal to at
least twenty-five percent (25%) of the maximum length of the first
plane.
(2) Vertical articulation.
No wall length shall extend for
a distance greater than three times the height of the wall without
changing height by a minimum of fifteen percent (15%) of the wall’s
height, and that new plane shall extend for a distance equal to at
least twenty-five percent (25%) of the maximum length of the first
plane. Pitched roofs shall count toward achieving vertical articulation,
provided they are 65 degrees or less from horizontal.
(Ordinance 2019-42 adopted 10/8/19)
(a) Specific design standards for non-residential structures up to three
(3) stories in height.
(1) Walls, excluding windows, doors and other openings, shall be constructed
of a minimum seventy percent (70%) category A materials and a maximum
of thirty percent (30%) category B materials. However, accent materials
from category C may be allowed in limited application for architectural
accents or features.
(2) A “big box” store or shopping center may use split-face
CMU (architectural block) for up to twenty percent (20%) of the primary
facade, in addition to the thirty percent (30%) of other category
B materials for a total of fifty percent (50%) category B materials.
(3) All exterior walls of buildings less than 15,000 square feet are
considered primary facades, regardless of orientation.
(4) A “primary facade” shall be as described in the definitions
or as otherwise determined by the director.
Article 14.04, Table 3A Exterior Materials for Non-Residential Buildings
|
---|
Categories
|
Materials
|
---|
A
|
Brick, stone, or manufactured stone
|
B
|
Split-face CMU, stucco, cementitious fiber board, quick brick,
tilt wall, treated engineered wood
|
C
|
Metal, natural wood, tile, glass, EIFS
|
Prohibited
|
Plain concrete block, aggregate, vinyl, plastic
|
Article 14.04, Table 3B Required Percentages of Exterior Materials for Non-Residential Buildings Three (3) or Fewer Stories
|
---|
Facades
|
Minimum Percentage
|
Definition
|
---|
Primary
|
Minimum 20% stone Remainder category A for a total of 70% category
A Maximum 30% category B
|
Exterior walls of buildings which are clearly visible from a
public street or along an active storefront, or as determined by the
director
|
Secondary
|
Minimum 30% category A Remainder category B
|
Exterior walls of buildings 15,000 square feet or larger which
are NOT clearly visible from a public street or along an active storefront
|
Article VI, Table 3C Facades (Big Box)
|
---|
Primary
|
Minimum 50% category A Remainder split faced CMU and other category
B
|
Exterior walls of buildings which are clearly visible from a
public street or along an active storefront
|
Secondary
|
Minimum 20% category A Remainder category B
|
Exterior walls of buildings 15,000 square feet or larger which
are NOT clearly visible from a public street or along an active storefront
|
(5) Facades shall generally be built parallel to the street frontage,
except at street intersections, where a facade containing a primary
building entrance should be curved or angled toward an intersection.
(6) All buildings within a common development, as shown on a development
plan, concept plan, or site plan, shall have similar architectural
styles, materials, colors, and detailing.
(7) All structures shall be architecturally finished on all sides that
can be seen from a public right-of-way with similar styles, materials,
colors, and detail.
(8) At least two masonry materials shall be used on all exterior facades.
Except for stone, no single material shall exceed seventy percent
(70%) of any given facade.
(9) All buildings shall be designed and constructed in tri-partite architecture
so that they have a distinct base, middle, and top, separated by horizontal
elements, as illustrated below.
(10) For buildings with a visible hip, gable, or mansard roof, allowed
materials include metal (standing seam), slate, or tile (clay or cement,
barrel, or Roman-shaped).
(11) Roofs shall be peaked with either hip, gable, or mansard design with
a minimum 1:4 pitch, or a parapet wall or false mansard design (minimum
1:2 pitch) is acceptable only if constructed around the entire perimeter
of a building so that no flat roof shall be visible from a public
street. At all times roof-mounted mechanical equipment shall be screened
from view.
(12) Windows and glazing shall be limited to a minimum of ten percent
(10%) and maximum of seventy percent (70%) of each building elevation.
Faux windows or elements that create a comparable visual, such as
decorative brickwork, insets of varying materials/colors, or other
similar features are allowed, subject to discretionary review and
approval by the director. All windows shall a maximum exterior visible
reflectivity of ten percent (10%).
(13) Columns shall be encased in category A masonry material used elsewhere
on the primary building.
(14) All streetscape elements and site amenities, such as bike racks,
trash receptacles, lampposts, benches, bollards, patio furniture,
and tree grates, shall be metal, rust and flake/chip resistant, and
generally be black in color. Minor deviations in color and design
that maintain the spirit and intent of the section are allowed with
director approval. Bollards can be concrete or cast metal and shall
be of decorative design with no bold colors or sleeves.
(b) Specific design standards for commercial structures four (4) stories
in height or taller.
(1) Facades shall generally be built parallel to the street frontage,
except at street intersections, where a facade containing a primary
building entrance should be curved or angled toward the intersection.
(2) All buildings within a common development, as shown on a development
plan, concept plan, or site plan, shall have similar architectural
styles, materials, colors, and detailing.
(3) All structures shall be architecturally finished on all sides that
can be seen from a public right-of-way with similar styles, materials,
colors, and detailing.
(4) Masonry requirement. Every elevation of each building shall be finished
with masonry as specified below. Acceptable masonry finishing materials
are brick, stone and/or synthetic stone materials including, but not
necessarily limited to, slate, flagstone, granite, limestone, glass,
and marble. See table 4, below.
Article 14.04, Table 4A Exterior Materials Categories for High Rise Buildings (4 or More Stories)
|
---|
Categories
|
Materials
|
---|
A
|
Brick, stone, manufactured stone, glass wall system
|
B
|
Split-face CMU, stucco, cementitious fiber board, treated engineered
wood, tilt wall construction
|
C
|
Metal, natural wood, tile, glass Blocks, EIFS
|
Prohibited
|
Plain concrete block, aggregate, vinyl, plastic
|
Article 14.04, Table 4B Minimum Exterior Percentages for High Rise Buildings (4 or More Stories)
|
---|
Floors 1–3
|
Minimum 70% category A
Maximum 20% category B
Remainder category C
|
Floors 4–6
|
Minimum 20% category A
Minimum 70% category B
Remainder category C
|
Floors 7 and above
|
0% category A required (but may be used)
Maximum 100% category B or C
|
(A) Metal or wood (other than treated engineered wood) exterior construction
is allowed only as an accent material to enhance the overall architectural
design.
(B) The director may approve deviations from a strict interpretation
of the exterior standards to accommodate specific “signature
design aesthetic.”
(C) No single building material shall be used for more than eighty-five
percent (85%) of any facade unless approved by writing by the director.
(D) Windows shall not be glazed or reglazed with mirrored or reflective
glass.
(5) All commercial buildings shall be architecturally finished with similar
exterior materials on all four sides with a higher level of finish
and articulation on the primary facade (at the primary entrance or
front door).
(6) The entrance or entrances on all buildings shall be articulated and
defined with strong architectural features.
(7) Ground floor facades facing major thoroughfares and any intersecting
thoroughfare must incorporate articulated entry areas, arcades, display
windows, awnings, or other architectural variety features along no
less than sixty percent (60%) of the facade.
(8) Any loading and service areas shall be located at the side or rear
of buildings. Horizontal articulation described above is not required
on the facade of buildings containing a loading dock and/or service
area, provided that such area is located in such a manner as to not
be readily visible from any major thoroughfare or any intersecting
roadway.
(Ordinance 2019-42 adopted 10/8/19)
(a) Design standards for industrial structures.
The following
design standards apply to structures constructed in an industrial
zoning district and proposing an industrial and/or manufacturing use,
per the use chart of the zoning ordinance:
(1) The main entry or office area of the building shall be articulated
both horizontally and vertically by at least five (5) feet or ten
percent (10%) of the adjacent wall height, whichever is greater. Building
corners shall also be articulated, as approved by the director.
(2) Primary exterior facades, which are clearly visible from a public
street, shall be constructed with a minimum ten percent (10%) category
A materials and up to ninety percent (90%) category B materials, exclusive
of windows and doors. Category C materials may be used for accents.
The category A materials noted above shall be applied to corners,
entries, and other areas in order to mitigate monotony and increase
the aesthetic value. A minimum of two (2) different materials shall
be used.
(3) Secondary exterior facades NOT facing a public street may be constructed
with up to 100% category B materials.
Article 14.04, Table 5A Exterior Materials for Industrial Buildings
|
---|
Categories
|
Materials
|
---|
A
|
Brick, Stone, or Manufactured Stone
|
B
|
Split-Face CMU, Stucco, Cementitious Fiber Board, Quick Brick,
Tilt Wall, Treated Engineered Wood
|
C
|
Metal, Natural Wood, Tile, Glass, EIFS
|
Prohibited
|
Plain Concrete Block, Aggregate, Vinyl, Plastic
|
Article 14.04, Table 5B Required Percentages of Exterior Materials for Industrial Buildings
|
---|
Facades
|
Minimum Percentage
|
Definition
|
---|
Primary
|
Minimum 10% category A
Remainder category B
Category C may be used as accents up to 5%
|
Exterior walls of buildings which are clearly visible from a
public street
|
Secondary
|
Up to 100% category B
|
Exterior walls NOT clearly visible from a public street or along
an active storefront
|
(b) Architectural features for industrial structures.
All
industrial buildings shall incorporate two (2) of the additional architectural
features listed below:
(1) Canopies (not drive-through canopies), awnings, valances or porticos;
(2) Overhangs (5 feet minimum);
(3) Recesses or projections (3 feet minimum);
(8) Recessed or “popped-out” display windows (2 feet minimum);
(9) Visible and noticeable architectural details, such as tile work or
moldings, integrated into building facade;
(10) Integrated planters or wing walls that incorporate landscape and
sitting areas; or
(11) Other architectural features with similar visual impact.
(Ordinance 2019-42 adopted 10/8/19)
(a) Gas pumps and fueling stations.
(1) Materials for the main building shall follow the regulations for non-residential structures (section
14.04.109, general design standards for non-residential structures).
(2) Canopies shall not exceed twenty (20) feet in total height, measured
from the pavement to the top of the canopy.
(3) The roofs of convenience store buildings and fueling station canopies
shall be pitched, include a parapet to shield roof-mounted equipment,
or otherwise distinguished, subject to approval by the director.
(4) Canopies and their supporting structures should be architecturally
integrated with the primary building and all other accessory structures
on the site by using the same or complementary materials, design motif,
and colors.
(5) Canopy support columns shall be fully encased with type A masonry
products and shall not include any non-structural additions to the
columns.
(6) Canopy band faces shall be a color consistent with the main structure
or an accent color. The canopy band face shall be flat with no projections,
shall not be of plastic materials, shall be generally a metal or masonry
based material, not be greater than four (4) feet in height, and may
not be backlit or used as signage; except as follows:
(A) The canopy band face may utilize one (1) small button logo on each
face that can be internally illuminated, as long as each button logo
does not exceed fifteen (15) square feet for bands three (3) feet
in height and twenty (20) square feet for bands four (4) feet in height,
is generally as tall as it is wide, and does not protrude more than
eighteen (18) inches from the canopy in any direction.
(B) The canopy band face may utilize an external LED halo type light,
if properly shielded/recessed and oriented downward so that only the
“wash” is visible.
(C) The canopy band face may utilize internally illuminated rings, as
long as the source is LED, it is flush with the band face and only
protrudes nominally (up to a maximum of six (6) inches), and the size
of the ring does not exceed more than twenty-five percent (25%) for
single rings and fifty (50%) for multiple rings of the thickness of
the canopy band face.
(7) Lighting fixtures (LED only) or sources of light that are a part
of the underside of the canopy should be recessed into the underside
of the canopy.
(8) The materials and color used on the underside of the canopy should
not be highly reflective, with the intent of minimizing the amount
and intensity of light, which reaches beyond the site boundaries.
(9) Materials and colors used on both structural and architectural surfaces
shall be subdued, earth-tone colors, with the intent of promoting
a harmonious appearance of the structures and the natural surroundings,
as well as with appearance themes or guidelines of surrounding development.
Brick, stone and other high-quality masonry type elements are required
as a major component of the exterior of all structures.
(10) Bright accent colors, intended to express corporate or business logos,
may be used only on a limited basis. These accent color areas should
not be internally illuminated, except as allowed by the city’s
sign regulations.
(11) Exhaust valves for underground fuel storage tanks shall be designed
to be located against a building, dumpster screening wall, or other
structure to mitigate their visual impact and should be an earth-tone
color. If impractical, the exhaust valves may be located in an interior
landscape area, if properly screened, but should not be located in
the exterior landscape buffer adjacent to the public right-of-way.
(12) Screening of fueling stations shall follow section
14.04.207, commercial landscaping requirements. However, use of berms to further screen the pump area is encouraged.
(Ordinance 2019-42 adopted 10/8/19)