A.
The following summarizes select standards applicable to these design standards. This list is not exclusive; other standards may apply. The latest revision of each standard shall be referenced.
B.
All materials and execution shall conform to the highest applicable standards. If there is a conflict between other standards, or between other standards and these design standards, then the most stringent criteria shall apply.
[Amended 4-5-2024]
Standards | Title/Subject |
|---|---|
29 CFR 1926 | OSHA Safety and Health Regulations for Construction |
29 CFR 1926.1101 | OSHA Safety and Health Regulations for Construction, Subpart Z, Toxic and Hazardous Substances: Asbestos |
29 CFR 1910.1001 | OSHA Occupational Safety and Health Standards, Subpart Z, Toxic and Hazardous Substances: Asbestos |
248 CMR 10.00 | Massachusetts Uniform State Plumbing Code |
521 CMR | Rules and Regulations of the Architectural Access Board |
AASHTO Section 30 | Division II (General-Interim 1998) |
AASHTO M 91 | Sewer and Manhole Brick (Made from Clay or Shale) |
AASHTO M 170 | Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
AASHTO M 199 | Standard Specification for Precast Reinforced Concrete Manhole Sections (ASTM C478) |
AASHTO M 252 | Corrugated Polyethylene Drainage Pipe |
AASHTO M 288 | Standard Specification for Geotextile Specification for Highway Applications |
AASHTO M 294 | Corrugated Polyethylene Pipe, 300- to 1,500-mm Diameter |
AASHTO T 99 | Standard Method of Test for the Moisture-Density Relations of Soils Using a 5.5-lb Rammer and a 12-in. Drop (Compaction Test Method C) |
ADA | American with Disabilities Act |
ATSSA | Guide to Temporary Traffic Control in Work Zones |
ASTM A36/A36M | Standard Specification for Carbon Structural Steel |
ASTM A48 | Standard Specification for Gray Iron Castings |
ASTM A513 | Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing |
ASTM A536 | Standard Specification for Ductile Iron Castings |
ASTM A615 | Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement |
ASTM A616 | Standard Specification for Rail-Steel Deformed and Plain Bars for Concrete Reinforcement |
ASTM A74 | Standard Specification for Cast Iron Soil Pipe and Fittings |
ASTM A746 | Standard Specification for Ductile Iron Gravity Sewer Pipe |
ASTM A888 | Grey Cast Iron, Cast Iron Class 20 |
ASTM B62 | Standard Specification for Composition Bronze or Ounce Metal Castings |
ASTM C32 | Standard Specification for Sewer and Manhole Brick (Made From Clay or Shale) |
ASTM C33 | Standard Specification for Concrete Aggregates |
ASTM C76 | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
ASTM C139 | Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes |
ASTM C144 | Standard Specification for Aggregate for Masonry Mortar |
ASTM C150 | Standard Specification for Portland Cement |
ASTM C270 | Standard Specification for Mortar for Unit Masonry |
ASTM C443 | Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets |
ASTM C478 | Standard Specification for Precast Reinforced Concrete Manhole Sections |
ASTM C564 | Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings |
ASTM C1244 | Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill |
ASTM D1557 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 feet-lbf/ft3) |
ASTM D1784 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
ASTM D207 | Standard Specification for Shellac Varnishes |
ASTM D2241 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
ASTM D2321 | Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
ASTM D2412 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
ASTM D2487 | Standard Practice for Classification of Soils for Engineering Purposes (USCS) |
ASTM D2737 | Standard Specification for Polyethylene (PE) Plastic Tubing |
ASTM D3034 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) |
ASTM D3139 | Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals |
ASTM D3212 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
ASTM D3350 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D4101 | Standard Specification for Polypropylene Injection and Extrusion Materials |
ASTM D478 | Standard Specification for Zinc Yellow (Zinc Chromate) Pigments |
ASTM D5813-04 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
ASTM D790 | Test Methods for Flexural Properties of Un-reinforced and Reinforced Plastics and Insulating Materials |
ASTM F1216 | Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube |
ASTM F2561-11 | Standard Practice for Rehabilitation of a Sewer Service Lateral and Its Connection to the Main Using a One Piece Main and Lateral Cured-In-Place Liner |
ASTM F477 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
ASTM F679 | Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings |
ATSSA | Guide to Temporary Traffic Control in Work Zones |
AWWA C104/ANSI 21.4 | American National Standard for Cement-Mortar Lining for Ductile-Iron Pipe and Fittings for Water |
AWWA C105/ANSI A21.5 | American Standard for Polyethylene Encasement for Ductile-Iron Pipe Systems |
AWWA C110/ANSI A21.10 | American National Standard for Ductile-Iron and Grey-Iron Fittings, 3 Inch Through 48 Inch for Water |
AWWA C111/ANSI A21.11 | American National Standard for Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings |
AWWA C115/ANSI A21.15 | Standard for Flanged Ductile-Iron Pipe With Threaded Flanges |
AWWA C150/ANSI A21.50 | American National Standard for the Thickness Design of Ductile-Iron Pipe |
AWWA C151/ANSI A21.51 | American National Standard for Ductile-Iron Pipe, Centrifugally Cast, for Water or Other Liquids |
AWWA C153/ANSI A21.53 | American National Standard for Ductile-Iron Compact Fittings, 3 In. Through 64 In. |
AWWA C5002 | AWWA Standards for Dry-Barrel Fire Hydrants |
AWWA C504 | AWWA Standard for Rubber-Seated Butterfly Valves |
AWWA C509 | AWWA Standard for Resilient-Seated Gate Valves for Water Supply Service |
AWWA C515 | AWWA Standard for Reduced-Wall Resilient-Seated Gate Valves for Water Supply Service |
AWWA C600 | AWWA Standard for the Installation of Ductile-Iron Water Mains and Their Appurtenances |
AWWA C651 | AWWA Standard for Disinfecting Water Mains |
AWWA C901 | Polyethylene (PE) Pressure Pipe and Tubing, 1/2 Inch – 3 Inch, for Water Service |
City of Framingham | City of Framingham Standard Operating Procedures for the Management of ACM |
MassDEP | 310 CMR 7.00, Air Pollution Control Regulations; includes Sections 7.09, Dust, Odor, Construction and Demolition, and 7.15, Asbestos |
MassDEP | Asbestos Cement Pipe Guidance Document (June 2011) |
MassDEP | Guidelines for Public Water Systems (April 2014) |
MassDEP | Stormwater Management Policy |
MassDEP | Massachusetts Stormwater Handbook |
MassDEP | 310 CMR 10.00, Wetland Protection Act |
MassDOT | Standard Specifications for Highways and Bridges, Construction and Traffic Standard Details (1996 et seq.) |
MassDOT | Construction and Traffic Standard Details |
MassDOT | Work Zone Safety Guidelines for Massachusetts Municipalities and Contractors |
MUTCD | Manual of Uniform Traffic Control Devices (MUTCD) |
NFPA 70 | National Electrical Code with Massachusetts and amendments |
NOAA | National Oceanographic and Atmospheric Administration: Technical Paper No. 40, May 19 "1 "Rainfall Frequency Atlas of the United States" |
US DOT | 49 CFR 100-185, Hazardous Materials Transportation |
US EPA | USEPA Region 1, MS4 Program |
US EPA | National Emission Standards for Hazardous Air Pollutants (NESHAPS) Title 40, Part 61 |
US EPA | Guide to Respiratory Protection for the Asbestos Abatement Industry |
US EPA | In a Guidance Letter dated July 17, 1991, identified as Control No. C99 within the Agency Applicability Determination Index, the U.S. EPA determined that "the pumping of grout into buried lines is not a process which, in and of itself, would cause asbestos cement pipe to become regulated asbestos containing material." |