(A) 
General purpose and descriptions.
The AG – Agricultural District is intended to provide a location for principally undeveloped or vacant land situated on the fringe of an urban area and used for agricultural purposes, but may become an urban area in the future.
Generally, the AG – Agricultural District, will be near development; therefore, the agricultural activities conducted in the AG – Agricultural District should not be detrimental to urban land uses.
The types of uses and the area and intensity of uses permitted in this District shall encourage and protect agricultural uses until urbanization is warranted and the appropriate change in district classification is made.
(B) 
Permitted uses.
Uses permitted in the AG – Agricultural District are outlined in Subsection 3.01 Use of Land and Buildings.
(1) 
Barns or stables.
Barns and stables shall not be considered an accessory building or use and shall be treated according to Subsection 3.02 Use Chart under the definition Farm, Ranch, Stable, Garden, or Orchard.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
Front yard coverage.
The cumulative area of any driveway plus any impermeable surface area located between the front property line and any front building wall shall not exceed fifty (50) percent of the area between the front property line and any front building wall, as shown in Figure 9.01.01.4: Front Yard Coverage.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and descriptions.
The RE – Residential Estate District will provide single-family detached dwelling units on large parcels of land.
(B) 
Permitted uses.
Uses permitted in the RE – Residential Estate District are outlined in Subsection 3.01 Use of Land and Buildings.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
Front yard coverage.
The cumulative area of any driveway plus any impermeable surface area located between the front property line and any front building wall shall not exceed fifty (50) percent of the area between the front property line and any front building wall, as shown in Figure 9.01.01.4: Front Yard Coverage.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and descriptions.
The SF-16 – Single-Family Residential-16 District is intended to provide for development of single-family detached dwelling units on lots of not less than sixteen thousand (16,000) square feet.
Other uses, such as religious and educational facilities will be provided for to maintain a balanced, orderly, convenient and attractive residential area.
(B) 
Permitted uses.
Uses permitted in the SF-16 – Single-Family Residential-16 District are outlined in Subsection 3.01 Use of Land and Buildings.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
Front yard coverage.
The cumulative area of any driveway plus any impermeable surface area located between the front property line and any front building wall shall not exceed fifty (50) percent of the area between the front property line and any front building wall, as shown in Figure 9.01.01.4: Front Yard Coverage.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and descriptions.
The SF-12.5 – Single-Family Residential-12.5 District is intended to provide for development of single-family detached dwelling units on lots of not less than twelve thousand, five hundred (12,500) square feet.
(B) 
Permitted uses.
Uses permitted in the SF-12.5 – Single-Family Residential-12.5 District are outlined in Subsection 3.01 Use of Land and Buildings.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
Front yard coverage.
The cumulative area of any driveway plus any impermeable surface area located between the front property line and any front building wall shall not exceed fifty (50) percent of the area between the front property line and any front building wall, as shown in Figure 9.01.01.4: Front Yard Coverage.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and descriptions.
The SF-10 – Single-Family Residential-10 District is intended to be similar to the SF-12.5 – Single-Family Residential-12.5 District except composed of detached, single-family residences on lots of not less than ten thousand (10,000) square feet.
(B) 
Permitted uses.
Uses permitted in the SF-10 – Single-Family Residential-10 District are outlined in Subsection 3.01 Use of Land and Buildings.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
Front yard coverage.
The cumulative area of any driveway plus any impermeable surface area located between the front property line and any front building wall shall not exceed fifty (50) percent of the area between the front property line and any front building wall, as shown in Figure 9.01.01.4: Front Yard Coverage.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and descriptions.
The SF-8.5 – Single-Family Residential-8.5 District is intended to be similar to the SF-12.5 and SF-10 Districts except composed of detached, single-family residences on lots of not less than eight thousand five hundred (8,500) square feet.
(B) 
Permitted uses.
Uses permitted in the SF-8.5 – Single-Family Residential-8.5 District are outlined in Subsection 3.01 Use of Land and Buildings.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
Front yard coverage.
The cumulative area of any driveway plus any impermeable surface area located between the front property line and any front building wall shall not exceed fifty (50) percent of the area between the front property line and any front building wall, as shown in Figure 9.01.01.4: Front Yard Coverage.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and descriptions.
The SF-7 – Single-Family Residential-7 District is designed to provide for a suitable residential environment for family life on parcels of land smaller and more compact in size, having a minimum lot area of seven thousand (7,000) square feet, while limiting the uses to single-family residences and their community services and facilities.
(B) 
Permitted uses.
Uses permitted in the SF-7 – Single-Family Residential-7 District are outlined in Subsection 3.01 Use of Land and Buildings.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
Front yard coverage.
The cumulative area of any driveway plus any impermeable surface area located between the front property line and any front building wall shall not exceed fifty (50) percent of the area between the front property line and any front building wall, as shown in Figure 9.01.01.4: Front Yard Coverage.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and descriptions.
The OTR – Original Town Residential District is designed specifically for the "Old Donation" section of the City, a recognized subdivision of land.
The OTR – Original Town Residential District standards will provide for a suitable residential environment for family life on small parcels of land.
Platted lots in the "Old Donation" are in twenty-five (25) foot widths with a preponderance of ownerships in multiples of this width. Therefore, standards are set forth in this District which accommodate the original platting, as well as the preferable standard for a minimum fifty (50) foot lot width, or two platted lots constituting a building site.
(B) 
Permitted uses.
Uses permitted in the OTR – Original Town Residential District are outlined in Subsection 3.01 Use of Land and Buildings.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
Minimum side yard.
Six (6) feet; twelve (12) feet on corner lot adjacent to side street; twenty-four (24) feet for swing-in garage.
(2) 
Minimum rear yard.
Eight (8) feet; twenty (20) feet for garage facing alley (can be reduced to twelve (12) feet but requires additional parking surface); twenty-four (24) feet for swing-in garage.
(3) 
Front yard coverage.
The cumulative area of any driveway plus any impermeable surface area located between the front property line and any front building wall shall not exceed fifty (50) percent of the area between the front property line and any front building wall, as shown in Figure 9.01.01.4: Front Yard Coverage.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(5) 
"Lot of Record" in "Old Donation" – 4.07.01 Residential Lot Regulations.
(6) 
4.07.09(E)OTR Facade Plan Requirement.
(7) 
Non-combustible fiber cement siding allowed per Chief Building Official approval. (See 4.07.09 Exterior Construction of Main Buildings.)
(8) 
Front porch required.
a. 
Porches shall be a minimum of seven (7) feet deep and may extend ten (10) feet past front building line provided that such encroachment does not result in a threat to the occupant's or public's health, safety or welfare.
b. 
The porch shall have a minimum area of seventy (70) square feet.
(E) 
OTR - Downtown Architectural Design Standards.
The Downtown Architectural Design Standards that apply to this district are contained in Subsection 9.06 Downtown Architectural Design Standards; OTC & OTR, to this Zoning Ordinance and are incorporated as if fully set forth herein.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and descriptions.
The PH – Patio Home District is provided to allow for development of "zero-lot line" homes in a modified residential district, which encourages greater use of the side yard areas. Clustered lot patterns with a common usable open space system can be incorporated as an integral part of the development.
(B) 
Permitted uses.
Uses permitted in the PH – Patio Home District are outlined in Subsection 3.01 Use of Land and Buildings. In addition, the following uses are permitted.
(1) 
Zero-lot line, or patio home, residential detached dwellings in a platted subdivision.
(2) 
Community Owned or Multiple Ownership Areas. Open space, community center, an access gate, an entrance guard facility, recreational building and facilities are permitted uses provided they are incidental to the above-described residential uses, are approved on a Final Plat, and meet the following conditions.
a. 
In accordance with the Subdivision Ordinance, a HOA shall be established to maintain open space, recreational areas, and other commonly owned facilities.
1. 
The developer is responsible for drafting the HOA documents pertaining to the HOA's responsibilities to maintain these areas.
2. 
Major creek areas delineated as the City's linear park system shown on either the City's Parks Master Plan or City's Hike & Bike Trail Master Plan shall not count towards the required open space. The Major Creeks areas not shown as part of either plan may count toward the required open space where lots do not back to the open space.
b. 
Prior to approval of a Final Plat, a document establishing the HOA shall be submitted to the city for review and approved by the City Attorney for conformance with all requirements and other applicable ordinances.
1. 
The City Attorney shall review and approve the HOA documents pertaining to maintenance of the HOA areas prior to their recording at the County.
2. 
The developer is responsible for reimbursement of the City Attorney's fees for reviewing these documents.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
For lots with a zero (0) side yard setback.
a. 
A roof overhang equipped with a gutter may extend a maximum of eight (8) inches into a neighboring property. No other roof overhangs or extensions from a wall may extend into a neighboring lot.
b. 
The closest exterior roofline to an adjacent property shall be storm guttered if the general slope of the roof falls toward the neighboring property. Gutters shall include returns to direct the water to the lot of origin.
c. 
The "zero" side shall be designated on the Final Plat. All access, maintenance, and use easements shall be provided on preliminary and Final Plats.
d. 
A five (5) foot wide access, maintenance, and use easement shall be dedicated on the Final Plat for all lots adjacent to lots with a "zero" side. The purpose of this easement is to give the adjoining owner access for maintenance of his/her dwelling.
e. 
The majority of one side of the structure shall be located within three (3) feet of one side lot line. Building walls which are located adjacent to the "zero" side of the lot shall not have any doors, windows, ducts, grills, vents, or other openings. This requirement precludes exterior walls forming enclosures for courts, patios, or similar indentations to the "zero" wall.
(2) 
Center option lots.
a. 
Lots not using a zero (0) side yard setback shall be considered center option lots.
b. 
Center option lots shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards.
(3) 
Minimum front yard.
a. 
Twenty-five (25) feet.
(4) 
Minimum rear yard.
a. 
Thirty (30) feet.
b. 
Garages on alley entry lots shall meet one of the following conditions:
1. 
Garage shall be set back ten (10) feet; or
2. 
Garage shall be set back a minimum of twenty (20) feet, but may exceed this distance.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(5) 
Subsection 4.13 Usable Open Space Requirements.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and description.
The 2F – Two-Family Residential (Duplex) District is intended to promote quality duplex residential development. Individual ownership of the two-family or duplex unit is encouraged.
This District may include neighborhoods consisting entirely of duplexes, or, when in accordance with the intent of the Comprehensive Plan, may provide a transition district between lower density residential areas and more intense residential, nonresidential areas, or Major Thoroughfares.
(B) 
Permitted uses.
Uses permitted in the 2F – Two-Family Residential (Duplex) District are outlined in Subsection 3.01 Use of Land and Buildings.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(E) 
Special district requirements.
(1) 
Land within the 2F District may be platted in a manner in which each dwelling unit is situated on a separately platted lot of record where the property line runs coincident with the common wall separating the dwelling units. This provision allows for the creation of two Single-Family Residence, Attached dwelling units.
a. 
Where lots are platted in this manner, the subdivision plat shall designate the location of lot lines which run coincident with the common wall between the dwelling units and the lot lines which run between the structures.
b. 
There shall be only one dwelling unit per lot, and no dwelling unit shall cross a designated outside lot line.
c. 
No single-family dwelling may be constructed on one of the designated pair of lots.
(2) 
All utilities shall be provided to each separate unit of each duplex in a 2F District such that each unit is individually metered.
(3) 
Special provisions shall be made when land is platted in a 2F District into lots consisting of Single-Family Residence, Attached dwelling units permitting a separately owned building unit to be placed on a separately platted lot.
a. 
Plats shall be submitted and approved subject to a legal instrument(s) setting forth the manner in which common facilities or shared elements of a structure on a lot are to be maintained, or repaired, and shall include facades, roofs, and fencing.
b. 
Building permits shall only be issued for a structure comprised of two dwelling units to be built either as a duplex or as two single-family attached dwelling units but not for a single-family detached dwelling unit.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and descriptions.
The TH – Townhome District provides for the development of attached residential dwelling units in structures built to accommodate three to eight units per structure.
Open space is encouraged in this District through provisions set forth in the standards for the District.
(B) 
Permitted uses.
Uses permitted in the TH – Townhome District are outlined in Subsection 3.01 Use of Land and Buildings.
(1) 
Community owned or multiple ownership areas.
Common open space, community centers, an access gates, an entrance guard facilities, recreational buildings and facilities are permitted uses provided they are incidental to the above-described residential uses, are approved on a Final Plat, and meet the following conditions.
a. 
In accordance with the Subdivision Ordinance, a homeowners association (HOA) shall be established to maintain open space, recreational areas, and other commonly owned facilities.
1. 
The developer is responsible for drafting the HOA documents pertaining to the HOA's responsibilities to maintain these areas.
b. 
Prior to approval of a Final Plat, a document establishing the HOA shall be submitted to the city for review and approved by the City Attorney for conformance with all requirements and other applicable ordinances.
1. 
The City Attorney shall review and approve the HOA documents pertaining to maintenance of the HOA areas prior to their recording at the County.
2. 
The developer is responsible for reimbursement of the City Attorney's fees for reviewing these documents.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and the following regulations. If there is a conflict between 2.06.04 and the following regulations, the following regulations shall control.
(1) 
Minimum front yard.
Twenty-five (25) feet.
(2) 
Minimum side yard.
a. 
Five (5) feet from a side property line when adjacent to open space lots or amenity center lots.
b. 
Fifteen (15) feet from a side property line when adjacent to detached residential dwelling units.
c. 
Twenty (20) feet from a side property line when adjacent to a dedicated street.
(3) 
Minimum rear yard.
Twenty (20) feet, sixty (60) feet when the building is in excess of one story and adjacent to a Single-Family Zoning District.
(4) 
Structure separation.
Structures on the same parcel shall have the following setbacks and/or minimum distance between structures.
a. 
Minimum front yard.
Twenty-five (25) feet.
b. 
Minimum side yard.
Ten (10) feet between buildings without openings (windows); fifteen (15) feet between buildings with openings and when adjacent to side street; sixty (60) feet when building is in excess of one story in height and adjacent to Single-Family Zoning District.
c. 
Minimum rear yard.
Twenty-five (25) feet; sixty (60) feet when the building is in excess of one story and adjacent to a Single-Family Zoning District.
(D) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(5) 
Subsection 4.13 Usable Open Space Requirements.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and description.
The MF-15 – Multifamily-15 District is an attached residential district intended to provide a maximum residential density of fifteen (15) dwelling units per Net Acreage, Subdivision. The principal permitted land uses will include multifamily dwellings.
(B) 
Permitted uses.
(1) 
Uses permitted in the MF-15 – Multifamily-15 District are outlined in Subsection 3.01 Use of Land and Buildings.
(2) 
Single-family residential development shall comply with the standards set forth in following districts.
Applicable Zoning Districts
Section
District Abbreviation – District Name
§ 2.03.02.
RE – Residential Estate District
§ 2.03.03.
SF-16 – Single-Family Residential-16 District
§ 2.03.04.
SF-12.5 – Single-Family Residential-12.5 District
§ 2.03.05.
SF-10 – Single-Family Residential-10 District
§ 2.03.06.
SF-8.5 – Single-Family Residential-8.5 District
§ 2.03.07.
SF-7 – Single-Family Residential-7 District
(3) 
When a multifamily zoning district is developed as single-family residential and is adjacent to a single-family residential zoning district(s), the first two rows of lots shall be developed to standards not more than two Single-Family Residential zoning districts more dense than the adjacent single-family residential zoning district(s).
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and Subsection 4.12 Multifamily Development Standards.
(D) 
Maximum density.
Fifteen (15) dwelling units per net acre.
(E) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(5) 
Subsection 4.12 Multifamily Development Standards.
(6) 
Subsection 4.13 Usable Open Space Requirements.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and description.
The MF-19 – Multifamily-19 District is an attached residential district intended to provide a maximum residential density of nineteen (19) dwelling units per Net Acreage, Subdivision. The principal permitted land uses will include multifamily dwellings.
(B) 
Permitted uses.
(1) 
Uses permitted in the MF-19 – Multifamily-19 District are outlined in Subsection 3.01 Use of Land and Buildings.
(2) 
Single-family residential development shall comply with the standards set forth in following districts.
Applicable Zoning Districts
Section
District Abbreviation – District Name
§ 2.03.02.
RE – Residential Estate District
§ 2.03.03.
SF-16 – Single-Family Residential-16 District
§ 2.03.04.
SF-12.5 – Single-Family Residential-12.5 District
§ 2.03.05.
SF-10 – Single-Family Residential-10 District
§ 2.03.06.
SF-8.5 – Single-Family Residential-8.5 District
§ 2.03.07.
SF-7 – Single-Family Residential-7 District
§ 2.03.09.
PH – Patio Home District
(3) 
When a multifamily zoning district is developed as single-family residential and is adjacent to a single-family residential zoning district(s), the first two rows of lots shall be developed to standards not more than two single-family residential zoning districts more dense than the adjacent single-family residential zoning district(s).
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards and Subsection 4.12 Multifamily Development Standards.
(D) 
Maximum density.
Nineteen (19) dwelling units per net acre.
(E) 
Other regulations.
(1) 
Subsection 4.03 Screening Standards.
(2) 
Subsection 4.04 Off-Street Parking and Loading Requirements.
(3) 
Subsection 4.06 Accessory Structure Standards.
(4) 
Subsection 4.07 Supplementary Regulations.
(5) 
Subsection 4.12 Multifamily Development Standards.
(6) 
Subsection 4.13 Usable Open Space Requirements.
(Ordinance 2021-07-47 adopted 7/6/21)
(A) 
General purpose and description.
The MH – Manufactured Home District is a detached residential district establishing standards for the development of a manufactured home park, or a manufactured home subdivision.
A manufactured home park offers spaces for the placement of manufactured home units on a lease or rental basis. Manufactured home subdivisions include individually platted lots, for sale within the subdivision, for the placement of manufactured home units. The District establishes area and design requirements for both parks and subdivisions, as well as yard requirements for individual lots.
(B) 
Permitted uses.
Uses permitted in the MH – Manufactured Home District are outlined in Subsection 3.01 Use of Land and Buildings.
(C) 
Area regulations.
Property and buildings shall conform to the related standards listed within 2.06.04 Residential Districts Development Standards.
(D) 
Special district requirements.
(1) 
Area for Manufactured Home Park or a Recreational Vehicle Park.
a. 
Minimum, five (5) acres; maximum, twenty-five (25) acres.
(2) 
Minimum Average Vertical Clearance of Manufactured Home Frame above Finished Ground Elevation.
a. 
Eighteen (18) inches.
(Ordinance 2021-07-47 adopted 7/6/21)