This Chapter sets forth architectural design standards to further refine intended building form and physical character. The styles were created to be harmonious with Santa Barbara's distinctive built environment and were selected to represent the most prevalent existing architectural styles. The Architectural Styles Map requires certain styles in areas of the city including those that are highly visible to the public or adjacent to sensitive historic resources. These standards supplement the standards in Chapter 25.02 (Zones), Chapter 25.04 (Building Types), and Chapter 25.05 (Frontages).
(Ord. 6170, 2/25/2025)
A. 
Façades. All façades shall be designed in compliance with the standards of this chapter, Chapter 25.05 (Frontages), and Section 25.04.160 (Massing and Façade Composition).
1. 
Unless stated otherwise, all subsections within each architectural style group ('style') identified in this chapter apply to all façades of a building, including primary front façades, secondary front façades, interior façades, and interior courtyard façades.
B. 
Architectural Styles.
1. 
One architectural style shall be selected for each new building in compliance with Section 25.01.120 (Architectural Styles Map).
2. 
Projects located in Historic Districts, Landmark Districts, or Potential Historic Districts are limited to the architectural styles required for that district, as described in either Chapter 30.57 (Landmark District and Historic District Overlay Zone), or the City's Historic Resource Design Guidelines, as applicable. If an architectural style is required in a Historic District, Landmarks District, or Potential Historic District, but is not available in this chapter, it is not allowed to be approved under this Title.
3. 
Projects using styles not included in this chapter are not allowed to be approved under this Title.
4. 
The Industrial sub-style is limited to projects in the M-C Manufacturing Commercial or CO-CAR Coastal-Oriented Commercial, Arts, and Recreation base zones as shown on the Architectural Styles Map.
5. 
All buildings on a single design site shall use the same style.
C. 
Elements.
1. 
Within each style, the standards for architectural elements apply to each architectural element wherever that element appears on a new building.
2. 
Individual element types (e.g., balconies, storefronts) or components (e.g., cornice, brackets) may be included or omitted on any given façade, but where included shall comply with the standards for the selected style, including the stated nominal dimensional standards.
3. 
Elements and components are required only where explicitly indicated.
D. 
All Styles Requirements. The following standards apply to each architectural style group.
1. 
Walls.
(a) 
Structural expansion joints shall be concealed by placement, color selection, or use of façade plane change.
(b) 
Stucco wall finish shall extend below the weep screed, flush with the wall surface above, and continue for a minimum of two inches below finish grade.
(c) 
Wall flashing to be anodized or painted to match wall, trim, or other main color of the building.
2. 
Skylights.
(a) 
Skylights shall be curb or deck mounted in line with the roof pitch. Domed skylights are not allowed.
(b) 
Skylights shall not be publicly visible. Skylights may be screened by the building form, landscape, or parapet.
3. 
Windows.
(a) 
Glazing divisions shall be positioned exterior to glass panes.
4. 
Dimensions. Lumber dimensions for trellises and carports are nominal.
5. 
Materials and Colors.
(a) 
Wood and composite wood shall be stained, sealed, or painted.
(b) 
Where used, metal shall be painted or treated to prevent shiny or reflective finishes.
(c) 
Paint, textile, and metal colors shall be selected from the Santa Barbara Guide: A Guide to Painting Buildings.
(d) 
Wrought iron shall have a minimum one-half-inch cross section.
(Ord. 6170, 2/25/2025)
Before you begin
Identify your zone. If you have not done this yet, go back to the Quick Code Guide: Development Standards (Section 25.01.130).
Instructions
Location
Identify the architectural styles that are allowed at your project location.
Section 25.01.120 (Architectural Styles Map)
Identify your architectural style group and select one of the 2 sub-styles within that group to apply
Subsections A and B of Section 25.06.040 (Craftsman Style Group), Section 25.06.050 (Mediterranean Style Group), or Section 25.06.060 (Contemporary Style Group)
Comply with the applicable standards for massing and façade composition.
Section 25.04.160 (Massing and Façade Composition)
Comply with wall and building roof form standards of selected sub-style.
Subsections C–G of Architectural Style
Comply with window and door standards of selected sub-style.
Subsections H–K of Architectural Style
Comply with external elements standards and material standards of selected sub-style
Subsections L up to Q of Architectural Style
(Ord. 6170, 2/25/2025)
A. 
General Description.
1. 
Craftsman Sub-Style. The Craftsman style emerged in the American west and was inspired by the English Arts and Crafts movement. The Craftsman bungalow house was prevalent from the 1900s to the 1940s. Since that time, it has been adapted to multi-unit and mixed-use prototypes.
2. 
Cottage Sub-Style. Prevalent in the early 20th century, the Cottage style, like Craftsman, was influenced by the English Arts and Crafts movement and its affinity for pre-industrial models. In Santa Barbara, the Cottage style accommodates a range of primarily Northern European vernacular expressions. Windows, bay windows, balconies, porches, and materials are based on elements used in these traditions.
B. 
Character Description.
1. 
Craftsman.
Massing of two and a half stories or less
Low-pitched roofs with deep eaves and exposed rafter tails
Horizontally proportioned openings made from ganged vertical windows
Emphasis on natural-appearing materials, including composite wood shingles
Asymmetrical composition with wall plane broken by projecting gable ends
Wall plane broken by projecting and/or recessed elements
2. 
Cottage.
Massing of two and a half stories or less
Asymmetrical massing with front-facing gables
Steeply-pitched shingle roof with low eaves; minimal projection at eave and rake
Windows with evenly-spaced divided lites
Stucco walls with or without half-timbering
Mix of arched doors and square, though occasionally segmented arched, windows
Elements of Craftsman Style
Example Building Elevation: Crafstman
C. 
Wall.
1. 
Craftsman.
Height Limitation
Building Height
2.5 stories max.
Trim1
Width
6" min.
A
Base
Height
1'-0" min.; 1 story max.
B
Required Articulation
Projecting Profile/Molding
C
Base is required for this sub-style.
Note:
1
Trim not required on portions of buildings where stucco, masonry, or stone is the primary wall material.
Elements of Cottage Style
Example Building Elevation: Cottage
2. 
Cottage.
Height Limitation.
Building Height
2.5 stories max.
Trim2
Edge Trim Width
4" min.
D
Half-Timbering Width
8" min.
E
Base
Height
1 story max.
F
Required Articulation
Projecting Profile/Molding
G
Base is not required for this sub-style.
Note:
2
Trim not required on portions of buildings where stucco, masonry, or stone is the primary wall material.
D. 
Building Roof.
Gable End Elevation
1. 
Craftsman.
Roof Form
Type
Gable, Hip, Shed3
Pitch
3:12 min.; 8:12 max.
H
2. 
Cottage.
Roof Form
Type
Gable, Shed4
Pitch
8:12 min.
H
Notes:
3
High side of shed roof must terminate into wall.
4
High side of shed roof must terminate into wall.
E. 
Rake.
Rake Section: Craftsman with Bracket
Rake Section: Cottage
1. 
Craftsman.
Height
Fascia
10" min.
I
Bracket Bracing Member
4" min.
J
Horizontal Projection
To Fascia: Main Roof Form
1'-8" min. 3'-0" max;
K
To Fascia: Dormer
8" min. 1'-2" max;
K
Bracket Projection Beyond Fascia
No min.; 1'-0" max.
L
2. 
Cottage.
Height
Fascia
8" min.
M
Horizontal Projection
Projection to Fascia
8" min.
N
F. 
Eave.
Open Eave Elevation: Craftsman
1. 
Craftsman.
Standards
Open Eave
Closed Eave
Height
Rafter
8" min.
N/A
O
Horizontal Projection5
Main Roof Form
2'-6" min.
N/A
P
Dormer
8" min.
N/A
P
Note:
5
Horizontal projection includes gutter, where occurs.
Closed Eave Elevation: Cottage
Open Eave Elevation: Cottage
2. 
Cottage.
Standards
Open Eave
Closed Eave
Height
Rafter
8" min.
N/A
Q
Horizontal Projection6
Overall
1'-0" min.
1'-0" min.
R
Note:
6
Horizontal projection includes gutter, where occurs.
G. 
Parapet: All. Flat roofs with parapets are not allowed in this style group. See Subsection E (Rake) and Subsection F (Eave) for standards applicable to sloped roofs.
H. 
Windows.
Typical Window Elevation: Craftman (Shown with 6 over 1 Glazing Division)
Typical Window Elevation: Cottage (Shown with 20 Parts Glazing Division)
1. 
All.
Opening Proportion, Height
S
to Width
T
Typical Window
Ground Floor
2:1 min.
Typical Upper Floor
7:4 min.
Accent Window
Rectangle
3:2 min. (2'-6" max. width)
Square
1:1 min. (3'-0" max. width)
Ganged Window
3:5 min.
Picture Window
6:5 min.
Dormer Window
7:4 min.
Window
Sash Widths
Rail
2" min.
U
Stile
2" min.
V
Trim Widths7
Head
6" min.
W
Jamb
6" min.
X
Apron
3" min.
Y
Ganged Window Elevation: Craftsman with 4 over 1 and 6 over 1 Glazing Divisions
Window Frame Recess
Depth
2" min. from face of surround to face of sash
Sill Projection
Depth
2" min. from face of surround
Pediment
Allowed
No
Mullions
Mullions required between ganged windows.
Note:
7
Trim required for windows only on buildings or parts of buildings with lap siding.
Bay Window Plan: Chamfered
Bay Window Plan: Square
2. 
Craftsman.
Opening
Shape
Rectangular
Window
Operation
Double-Hung, Single-Hung, Awning, Casement, Fixed
Glazing Divisions
4 over 1, 6 over 1, or 10 over 1
Width of lites shall be no greater than their height.
3. 
Cottage.
Opening
Shape
Rectangular, Arched
Window
Operation
Double-Hung, Single-Hung, Awning, Casement, Fixed
Glazing Divisions
6 parts min.;
24 parts max.
Width of lites shall be no greater than their height.
I. 
Bay Windows: All.
Bay Window Elevation
Form
Type
Square, Chamfered
Interior Angle for Chamfered Form
30 degrees min.;
55 degrees max.
Z
Continuous horizontal articulation on building shall wrap bay window form.
Dimensions
Width
6'-0" min.; 12'-0" max.
A
Depth
1'-0" min.; 4'-0" max.
B
Bay window that does not extend to grade shall be supported on brackets.
Bay window form shall be vertically continuous from lowest bay window to highest bay window.
Allowed Cornice Treatments
Bay window stops below building eave (provide roof or cornice for bay window).
Corner Placement
At building corner, square bay window may be rotated 45 degrees.
When wrapping a corner, chamfered bay window may incorporate up to 5 faces instead of the typical 3.
J. 
Dormers.
Dormer Elevation: Craftsman
1. 
Craftsman.
Roof Form
Type
Shed
Pitch
3:12 min.; 7:12 max.
Horizontal Projection
Rake
See Subsection E.1 (Rake) for rake standards.
C
Eave
See Subsection F.1 (Eave) for eave standards.
Placement
Setback from Side Façade
3'-0" min.
Setback from Façade to Face of Dormer
1'-0" min.
Dormers shall not interrupt continuity of main building roof eave.
Window
See Subsection H (Windows) for window standards.
Dormer Elevation: Cottage Shown with Gable Roof
2. 
Cottage.
Roof Form
Type
Gable, Hip
Pitch
6:12 min.; 10:12 max.
D
Horizontal Projection
Rake
See Subsection E.2 (Rake) for rake standards.
Eave
See Subsection F.2 (Eave) for eave standards.
Placement
Setback from Side Façade
3'-0" min.
Setback from Façade to Face of Dormer
1'-0" min.
Dormers shall not interrupt continuity of main building roof eave.
Window
See Subsection H (Windows) for window standards.
K. 
Entry Doors.
Vision Glass Door Elevation with Two Panels and Square Span
Half Glass Door Elevation with Three Panels and Sidelights
Full Glass Door Elevation with Transom: Craftsman
1. 
Craftsman.
Door
Number of Panels
2 min.8
Lite Types/Glazing Divisions
Vision Glass
3 parts min.
Half Glass
6 parts min.
Full Glass
3 parts min. over 1
Surround
Span Type
Lintel
Head Width
6" min.
E
Jamb Width
4" min.
F
Glazed Openings
Transom
Allowed
Sidelights
Allowed
Placement
No portion of door shall be allowed within 1'-6" of outside corners of building.
Doors shall be centered along width of balconies and arches, where occurs.
Note:
8
Panels not required for full glass lite type.
2. 
Cottage.
Door
Number of Panels
2 min.9
Lite Types/Glazing Divisions
Vision Glass
4 parts min.
Half Glass
8 parts min.
Full Glass
16 parts min.
Surround
Span Type
Lintel, Arch
Head Width
6" min.
E
Jamb Width
4" min.
F
Glazed Openings
Transom
Allowed
Sidelights
Allowed
Placement
No portion of door shall be allowed within 1'-6" of outside corners of building.
Doors shall be centered along width of balconies and arches, where occurs.
Note:
9
Panels not required for full glass lite type.
L. 
Columns/Pilasters.
One-Story Porch with Square Tapered Column and Capital Connection: Craftsman
1. 
Craftsman.
Columns + Pilasters
Shape
Square, Square Tapered
Width/Diameter
9" min. each
Spacing
9'-6" min., 12'-0" max. on center
G
Pedestal Height10
3'-0" min.
Entablature/Beam Connection
Capital, Mortise and Tenon
Columns may be paired.
Columns must not span multiple stories.
Additional Features
Paneling
Allowed
Fluting
Not Allowed
Entablature Height
Topmost Floor
1'-6" min.
H
Intermediate Floor
10" min.
Guard/Railing
Allowed Types
Square, Flat Sawn
Width Between Posts
3'-0" min. on center
Note:
10
Pedestal may be omitted.
One-Story Porch with Paired Square Columns on Pedestals and Mortise and Tenon Connection: Cottage
2. 
Cottage.
Columns + Pilasters
Shape
Square
Width/Diameter
6" min. each
Spacing
8'-0" max. on center
I
Pedestal Height11
3'-0" min.
J
Entablature/Beam Connection
Capital, Mortise and Tenon
Columns may be paired.
Columns must not span multiple stories.
Additional Features
Paneling
Allowed
Fluting
Not Allowed
Entablature
Topmost Floor
1'-6" min.
K
Intermediate Floor
10" min.
Guard/Railing
Allowed Types
Square, Flat Sawn
Width Between Posts
3'-0" min. on center
Note:
11
Pedestal may be omitted.
M. 
Balconies: All.
Juliet Balcony with Flat Sawn Railing, Front Elevation
Allowed Types
Type 1 - Juliet Balcony
Inward-swinging door with full glazing required
L
Base Height
3" min.
M
Base Projection
4" min.; 2'-0" max.
Type 2 - Occupiable Balcony
Clear Depth
6'-0" min.
Area
48 sq. ft. min.
Recess into Façade
4'-6" max.
Overall Width
10'-0" max.
Occupiable Balcony with Flat Sawn Railing, Front Elevation
Occupiable Balcony with Square Railing, Front Elevation
Guard/Railing
Allowed Types
Square, Flat Sawn
Height
Per Building Code
N
Width Between Posts
3'-0" min. on center
O
Brackets/Supports
Allowed Types
Brackets, Cantilevered Beams
Depth
80% of projection depth at bracket, min.
Height
50% of bracket depth, min.
P
Spacing
6'-0" on center; max.
Q
N. 
Storefronts: All.
Storefront Section
Storefront Elevation
Width
Storefront Module12
10'-0" min.; 25'-0" max.
R
Display Window
3'-0" min.; 6'-0" max.
S
Distance Between Storefront Modules
1'-0" min.; 6'-0" max.
T
Height
Overall
13'-0" min.
U
Head Height
10'-0" min.
V
Cornice
10" min.
W
Signage Band
1'-6" min.
X
Bulkhead
1'-0" min.; 2'-0" max.
Y
Horizontal Recess
Depth
6" min.; 1'-0" max.13
Z
Bulkhead shall be continuous, unless divided by pilaster, and align with base height of building (if any).
Cornice shall be continuous.
Notes:
12
May be expressed as a pilaster. See Subsection L (Columns/Pilasters).
13
No max. depth for residential entries.
O. 
Awning: All.
Awning Section: Craftsman
Awning Elevation: Craftsman
Awning
Eave Height
6" min.
A
Horizontal Projection14
3'-0" min.
B
Required Support Elements
Brackets
Bracket Width
4" min.
C
Roof Pitch
3:12 min.
D
Note:
14
Horizontal projection includes gutter, where occurs.
P. 
Trellises and Carports: All.
Dimensions
Post
8" x 8" min.
E
Main and Cross Beam
4" x 8" min.15
F
Rafter
2" x 4" min.
G
Purlin or Lattice
2" x 2" min.
H
Overhang
I
Beams
3'-0" max.
Purlin or Lattice
2'-0" max.
Trellis
1'-6" max.
Note:
15
Paired 2" x 8" members are allowed when placed on both sides of the supporting posts.
Q. 
Materials.
1. 
Craftsman.
Element
Allowed Materials
Building Walls
Cladding
Shingle or lap siding (wood, composite wood, fiber cement), stucco
Base or Foundation
Stucco, stone, cast stone, colored or painted concrete
Roof and Roof Elements
Roofing
Shingles (composite wood, slate, dimensional or luxury asphalt shingles to mimic the look of wood or slate); standing seam metal (black, white, or reflective metal finishes are prohibited)
Rake and Eave
Wood, composite wood
Cornice
Wood, composite wood
Brackets
Wood, composite wood, fiberglass
Gutter
Half-round copper, metal
Windows, Bay Windows, and Entry Doors
Trim or Surround
Wood, composite wood, fiber cement
Entry Door
Wood, composite wood, aluminum-clad wood, fiberglass
Window Frames
Wood, aluminum-clad wood
Glazing
Clear glass; shall not be tinted, mirrored, or colored
Garages
Garage Door16
Wood, composite wood, fiberglass
Balconies
Post, Handrail, Fascia, and Support Members
Wood, composite wood, solid metal
Railing
Wood, composite wood, metal
Porches
Columns
Wood, composite wood, sandstone, metal
Railing
Wood, composite wood, solid metal
Storefronts
Storefront Module
Wood, composite wood, metal, fiberglass
Storefront Base (Bulkhead)
Wood, brick, stone, tile, fiber cement
Chimneys
Cap
Copper, steel
Body
Brick, stone, cast stone (including veneers of any of the above)
Exterior Building Lighting
Body and Mount
Wrought iron, metal
Shield
Clear, translucent, punched, louvers
Stairs and Ramps
Treads and Risers
Wood, composite wood, stucco, brick, stone
Handrails
Wood, composite wood, stucco, stone, wrought iron, metal
Trellises and Carports
Spanning Members
Wood, composite wood
Trellis Posts
Wood, composite wood
Carport Support Posts
Wood, composite wood, stucco
Trash Enclosure
Walls
Wood, composite wood, stucco
Fences and Hedges
Walls
Stucco, brick, stone (faux manufactured stone veneer is prohibited), concrete block (coated and painted or pigmented to match the main building)
Fences17
Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)
Notes:
16
Metal roll up doors are allowed only if not publicly visible. Metal security grilles are allowed for parking structures.
17
Publicly visible fences may not be chain link unless screened with vines.
2. 
Cottage.
Element
Allowed Materials
Building Walls
Cladding
Wood, composite wood, stucco, brick, stone, fiber cement
Base or Foundation
Stucco, brick, stone, cast stone, colored or painted concrete
Roof and Roof Elements
Roofing
Shingles (composite wood, slate, dimensional or luxury asphalt shingles to mimic the look of wood or slate)
Rake and Eave
Wood, composite wood
Cornice
Wood, composite wood
Brackets
Wood, composite wood, fiberglass
Gutter
Half-round copper, metal
Windows, Bay Windows, and Entry Doors
Trim or Surround
Wood, composite wood, fiber cement
Entry Door
Wood, composite wood, aluminum-clad wood, fiberglass
Window Frames
Wood, aluminum-clad wood
Glazing
Clear glass; shall not be tinted, mirrored, or colored
Garages
Garage Door18
Wood, composite wood, fiberglass
Balconies
Post, Handrail, Fascia, and Support Members
Wood, composite wood, solid metal
Railing
Wood, composite wood, metal
Porches
Columns
Wood, composite wood, metal, fiberglass
Railing
Composite wood, wood, solid metal
Storefronts
Storefront Module
Wood, composite wood, metal
Storefront Base (Bulkhead)
Wood, stucco, brick, fiber cement
Chimneys
Cap
Copper, steel
Body
Brick, stone, cast stone (including veneers of any of the above)
Exterior Building Lighting
Body and Mount
Wrought iron, metal
Shield
Clear, translucent, punched, louvers
Stairs and Ramps
Treads and Risers
Wood, composite wood, stucco, brick, stone
Handrails
Wood, composite wood, stucco, stone, wrought iron, metal
Trellises and Carports
Spanning Members
Wood, composite wood
Trellis Posts
Wood, composite wood
Carport Support Posts
Wood, composite wood, stucco
Trash Enclosure
Walls
Wood, composite wood, stucco
Fences and Hedges
Walls
Stucco, brick, stone (faux manufactured stone veneer is prohibited), concrete block (coated and painted or pigmented to match the main building)
Fences19
Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)
Notes:
18
Metal roll up doors are allowed only if not publicly visible. Metal security grilles (including roll up function) are allowed for parking structures.
19
Publicly visible fences may not be chain link unless screened with vines.
(Ord. 6170, 2/25/2025)
A. 
General Description.
1. 
Spanish Colonial Revival Sub-Style. The Spanish Colonial Revival style is a reflection of Santa Barbara's Spanish architectural tradition. The sub-style adheres to simple building massing, the impression of traditional masonry construction, prominence of clay tile roof forms, and craftsmanship with an emphasis on raw materials.
2. 
Italian Mediterranean Sub-Style. While similar to the Spanish Colonial Revival style in terms of cladding and materials, the Italian Mediterranean style is expressed through the symmetrical and formal composition of openings, the cornice detailing at rakes and eaves, and the types of columns and pilasters used.
B. 
Character Description.
1. 
Spanish Colonial Revival
Flat roofs or low-pitched gabled and/or hipped roofs, often stepped and with simple eave and cornice details
Red cap-and-pan, terra-cotta clay roof tile installed with a scattered field pattern, random mortar lifts, and selectively placed booster tile
Flat, rectilinear wall plane with symmetrical or asymmetrical compositions of vertically proportioned punched openings without trim
Stucco as primary façade material with stucco or wood attached elements, and decorative tile at surrounds/stairs
Architectural details and materials display influence of Spanish and Moorish architecture
Ornamental elements, such as chimneys, vents, and gutters
2. 
Italian Mediterranean
Low-pitched hipped roofs clad in red tile with boxed eaves, often bracketed
Flat, rectilinear wall plane with vertically proportioned punched openings without trim
Stucco as primary façade material with stucco, wood, or metal attached elements
Formal and/or symmetrical composition of doors and windows
Use of classical orders, including columns and pilasters, to accentuate entrances and openings
Elements of Spanish Colonial Revival
C. 
Wall: All.
Base
Base is not required for this style group.
Wall Projections
Wall projections are allowed, but not required.
Depth
1'-0" min.
A
Provide lintel for full width of projection.
B
Elements of Italian Mediterranean Style
D. 
Building Roof: All.
Gable End Elevation
Standards
Sloped Roof
Flat Roof
Roof Form
Type
Gable, Hip, Shed1
Flat2,3
Pitch
3:12 min.; 6:12 max.
N/A
C
Applicable Subsections
E. Rake
Applies
N/A
F. Eave
Applies
N/A
G. Parapet
N/A
Applies
Roof Tile Installation Standards
Starter course shall be double tiled, min.
Unpigmented mortar required at birdstops, hips, and ridges.
Attic Vents
Placement
Centered within gable
D
Notes:
1
High side of shed roof must terminate into wall.
2
Flat roof parapets that are publicly visible cannot exceed 25% of the building length, or 25' max., whichever is greater.
3
In the El Pueblo Viejo Landmark District, flat roof parapets cannot be publicly visible.
Rake Elevation (with Ornamental Scored Scallop Pattern)
Rake Section (with Ornamental Scored Scallop Pattern)
E. 
Rake: All
Allowed Ornament4
Height
1'-0" min.
E
Projection to Rake Tile
3" min.
F
Note:
4
Scored scallop pattern shall align with tile breaks, where occurs.
F. 
Eave.
Returned Eave Section: Italian Mediterranean
Open Eave Section: Italian Mediterranean
Closed Eave Section: Spanish Colonial Revival
1. 
Spanish Colonial Revival.
Standards
Closed
Open
Returned
Horizontal Projection5
Overall
3" min.
N/A
N/A
G
Note:
5
Horizontal projection includes gutter.
Returned Eave Elevation: Italian Mediterranean
Open Eave Elevation: Italian Mediterranean
Closed Eave Elevation: Italian Mediterranean
2. 
Italian Mediterranean.
Standards
Closed
Open
Returned
Horizontal Projection6
Overall
1'-0" min.
3'-0" min.
2'-6" min.
H
Fascia/Cornice Molding
Height
1'-0" min.
N/A
6" min.
I
Allowed Rafter Tails and Supports
Type
N/A
Shaped, Plumb Cut
Shaped
Height
N/A
8" min.
1'-0" min.
J
Width
N/A
3" min.
3" min.
K
Spacing
N/A
2'-0" max. on center
2'-0" max. on center
L
Placement
N/A
Below decking
Below fascia
Note:
6
Horizontal projection includes gutter.
G. 
Parapet.
Parapet Section: Spanish Colonial Revival
Parapet Elevation: Spanish Colonial Revival
1. 
All.
Allowed Ornament
Type
Wall Moulding at Top of Parapet
Height
2'-0" max.
M
Projection
1'-0" max.
N
Placement
Continuous with Parapet Cap
Sloped Roof Parapet Section: Spanish Colonial Revival
Sloped Roof Parapet Elevation: Spanish Colonial Revival
2. 
Spanish Colonial Revival.
Sloped Roof with Parapet
Eave Projection
See Subsection F.1 (Eave) for eave standards.
O
Parapet Height
2'-6" min.
P
Sloped roof shall extend to reach full height of parapet.
Sloped roof portion shall comply with all standards applicable to sloped roofs in Subsection D (Building Roof).
Sloped Roof Parapet Section: Italian Mediterranean
Sloped Roof Parapet Elevation: Italian Mediterranean
3. 
Italian Mediterranean.
Sloped Roof with Parapet
Eave Projection, Profile, and Supports
See Subsection F.2 (Eave) for eave standards.
Q
Parapet Height
2'-6" min.
R
Sloped roof shall extend to reach full height of parapet.
Sloped roof portion shall comply with all standards applicable to sloped roofs in Subsection D (Building Roof).
H. 
Windows: All.
Typical Window Elevation with 8 Parts Glazing Divisions: Spanish Colonial Revival
Ganged Window Elevation with 6 Parts Glazing Divisions: Italian Mediterranean
Opening Proportion, Height
S
to Width
T
Typical Window
Ground Floor
2:1 min.
Typical Upper Floor
7:4 min.
Accent Window
Rectangle
3:2 min. (2'-6" max. width)
Square
1:1 min. (3'-0" max. width)
Ganged Window
3:5 min.
Picture Window
6:5 min.
Dormer Window
7:4 min.
Opening
Shape
Rectangular, Arched
Window
Operation
Casement, Fixed
Glazing Divisions7
6 or 8 parts
Width of lites shall be no greater than their height.
Sash Widths
Rail
2" min.
U
Stile
2" min.
V
Moulding Widths
Head
2" min.
W
Jamb
2" min.
X
Apron
None
Window Frame Recess
Depth
2" min. from face of surround to face of sash.
Sill Projection
Depth
2" min. from face of surround.
Pediment
Allowed
Italian Mediterranean only
Mullions
Mullions required between ganged windows.
Placement
No portion of window shall be allowed within 1'-6" of outside corners of building.
Note:
7
Glazing divisions for picture and accent windows may be one part. Italian Mediterranean may also have 10, 12, or 15 equal parts.
I. 
Bay Windows: All.
Bay Window Plan
Bay Window Elevation
Form
Type
Square
Continuous horizontal articulation on building shall wrap bay window form.
Dimensions
Width
6'-0" min.; 12'-0" max.
Y
Depth
1'-0" min.; 4'-0" max.
Z
Height
Bay window may extend from second story to top story.
Bay window may occupy first story on buildings less than 3 stories tall.
Bay window that does not extend to grade shall be supported on brackets.
Bay window form shall be vertically continuous from lowest bay window to highest bay window.
Allowed Cornice Treatments
Building parapet wraps bay window.
Bay window stops below building eave (provide roof or cornice for bay window).
Bay window terminates into building eave (bay window shall not project vertically or horizontally beyond building eave).
J. 
Dormers: All.
Dormer Elevation with Gable Roof
Roof Form
Type
Gable
Pitch
3:12 min.; 6:12 max.
A
Horizontal Projection
Rake
See Subsection E (Rake) for rake standards.
Eave
See Subsection F (Eave) for eave standards.
Placement
Setback from Side Façade
3'-0" min.
Setback from Façade to Face of Dormer
1'-0" min.
Dormers shall not interrupt continuity of main building roof eave.
Window
See Subsection H (Windows) for window standards.
K. 
Entry Doors: All.
Vision Glass Door Elevation with Two Panels and Arched Span
Half Glass Door Elevation with Two Panels and Sidelights
Full Glass Door Elevation with Transom and Entablature: Italian Mediterranean
Door
Number of Panels
2 min.8
Frame Recess
4" min. from face of door to face of surround.
Lite Types/Glazing Divisions
Vision Glass
0 parts min.; 4 parts max.
Half Glass
6 parts
Full Glass
8 parts min.; 15 parts max.
Surround
Span Type
Square, Arch
Glazed Openings
Transom
Allowed
Sidelights
Allowed
Entablature
Italian Mediterranean only
Pediment
Italian Mediterranean only
Placement
No portion of door shall be allowed within 1'-6" of outside corners of building.
Doors shall be centered along width of balconies and arches, where occurs.
Note:
8
Panels not required for full glass lite type.
L. 
Columns/Pilasters.
One-Story Porch with Square Column and Capital Connection: Spanish Colonial Revival
1. 
Spanish Colonial Revival
Columns + Pilasters
Shape
Square, Round
Width/Diameter
8" min. each
Spacing
9'-0" max. on center
B
Pedestal Height9
3'-0" min.
C
Entablature/Beam Connection
Capital, Bracket, Corbel
Columns must not span multiple stories.
Additional Features
Paneling
Allowed
Fluting
Not Allowed
Entablature Height
Topmost Floor
1'-6" min.
D
Intermediate Floor
10" min.
Guard/Railing
Allowed Types
Square, Turned (includes balustrade), Wall
Width Between Posts
3'-0" min. on center
Note:
9
Pedestal may be omitted.
One-Story Porch with Square Column and Capital Connection: Italian Mediterranean
2. 
Italian Mediterranean
Columns + Pilasters
Shape
Square, Round, Tuscan (Tapered)
Width/Diameter
8" min. each
Spacing
9'-0" max. on center
E
Pedestal Height10
3'-0" min.
Entablature/Beam Connection
Capital
Columns must not span multiple stories.
Additional Features
Paneling
Allowed
Fluting
Not Allowed
Entablature Height
Topmost Floor
1'-6" min.
F
Intermediate Floor
10" min.
Guard/Railing
Allowed Types
Square, Turned (includes balustrade), Wall
Width Between Posts
3'-0" min. on center
Note:
10
Pedestal may be omitted.
M. 
Balconies: All.
Juliet Balcony with Decorative Metal Railing, Front Elevation
Recessed Balcony with Stucco Wall, Front Elevation
Balcony with Square Railing, Front Elevation
Balcony with Turned Railing, Front Elevation
Allowed Types
Type 1 - Juliet Balcony
Inward-swinging door with full glazing required
G
Base Height
3" min.
H
Base Projection
4" min.; 2'-0" max.
Type 2 - Occupiable Balcony
Clear Depth
6'-0" min.
Area
48 sq. ft. min.
Recess into Façade
6'-8" max.
Overall Width
10'-0" max.
Guard/Railing
Allowed Types
Square, Turned (includes balustrade), Wall11
Height
Per Building Code
I
Width Between Posts
3'-0" min. on center
J
Brackets/Supports
Allowed Types
Brackets, Cantilevered Beams
Depth
80% of projection depth at bracket, min.
Height
50% of bracket depth, min.
K
Spacing
4'-0" on center, max.
L
Note:
11
Wall is allowed only for recessed balconies and shall not be used for Juliet Balcony.
N. 
Store fronts: All.
Storefront Section
Storefront Elevation
Width
Storefront Module12
10'-0" min.; 25'-0" max.
M
Display Window
3'-0" min.; 6'-0" max.
N
Distance Between Storefront Modules
1'-6" min.; 6'-0" max.
O
Height
Overall
None
Head Height
10'-0" min.
P
Cornice
None
Signage Band
None
Bulkhead
1'-0" min.; 2'-0" max.
Q
Horizontal Recess
Depth
1'-0" min.; 2'-0" max13
R
Bulkhead shall be continuous, unless divided by pilaster, and align with base height of building (if any).
For arched storefronts, see Section 25.05.130 (Arcades).
Notes:
12
May be expressed with pilasters. See Subsection L (Columns/Pilasters).
13
No max. depth for residential entries.
O. 
Awnings: All.
Awning Section
Awning Elevation with Straight Valance
Awning Design
Horizontal Projection
3'-0" min.
S
Offset from Opening
6" max.
T
Surface Shape14
Angled Surface with Open Sides
Valance Shape
Straight
Required Support Elements
Finials15
The bottom edge of the valance shall fall below the window or door head height, unless this conflicts with minimum clear height standards.
Supports shall not be installed horizontally, and shall angle up from the point of wall attachment at an angle equal to the slope of the awning surface.
Notes:
14
Horizontally segmented, curved, and domed awnings are prohibited, except that curved awnings are allowed for an arched opening if placed within the arch such that the form and depth of the arch are still visible.
15
Finials must be spear points in the Spanish Colonial Revival sub-style.
P. 
Trellises and Carports: All.
Trellis Diagram
Dimensions
Post
8" x 8" min.
U
Main and Cross Beam
4" x 8" min.16
V
Rafter
2" x 4" min.
W
Purlin or Lattice
2" x 2" min.
X
Overhang
Y
Beams
3'-0" max.
Purlin or Lattice
2'-0" max.
Trellis
1'-6" max.
Note:
16
Paired 2" x 8" members are allowed when placed on both sides of the supporting posts.
Q. 
Materials.
1. 
Spanish Colonial Revival.
Element
Allowed Materials
Building Walls
Cladding
Stucco
Accent Materials
Stone, tile
Projection Materials
Wood, cast-stone
Roof and Roof Elements
Roofing17
Two-piece (cap-and-pan)terra-cotta clay barrel tiles
Rake and Eave
Wood, composite wood, stucco
Cornice
Wood, composite wood, stucco
Brackets and Corbels
Wood, composite wood, stucco, fiberglass
Parapet Cap
Stucco, two-piece (cap-and-pan) terra-cotta clay barrel tiles
Finials
Metal (copper, cast iron, steel)
Attic and Mechanical Vents
Vent
Masonry, terra-cotta clay barrel tiles, wood louvers, wrought iron grill
Gutters, Downspouts, and Leaderheads
Gutter Profile
Half-round
Downspout Profile
Round
Materials
Copper18, metal
Windows, Bay Windows, and Entry Doors
Entry Door
Wood, composite wood, aluminum-clad wood, fiberglass
Window Frames
Wood, aluminum-clad wood, steel
Door/Window Surrounds
Stucco, stone, cast stone, tile
Sill
Stucco, stone, cast stone
Glazing
Clear glass; shall not be tinted, mirrored, or colored
Garages
Garage Door19
Wood, composite wood, fiberglass
Balconies
Post, Handrail, Fascia, Railing, and Brackets
Wood, composite wood, wrought iron, metal20
Deck Soffit
Wood, composite wood, stucco, wrought iron, tile (glazed, terra-cotta), metal
Porches
Columns
Wood, composite wood, stucco fiberglass, metal
Railing
Wood, composite wood, wrought iron
Storefronts
Storefront Module
Wood, composite wood, metal
Storefront Base (Bulkhead)
Stucco, tile
Chimneys
Cap
Stucco, terra-cotta clay barrel tiles, copper, steel
Body
Stucco, brick, stone, cast stone (including veneers of any of the above)
Exterior Building Lighting
Body and Mount
Wrought iron, metal
Shield
Clear, translucent, punched, louvers
Stairs and Ramps
Treads and Risers
Wood, composite wood, stucco, brick, stone, tile, concrete20
Handrails
Wood, composite wood, stucco stone, wrought iron, metal
Trellises and Carports
Spanning Members
Wood
Trellis Posts
Wood
Carport Support Posts
Wood, composite wood, stucco,
Connections
Steel, iron
Trash Enclosure
Walls
Wood, composite wood, stucco
Fences and Hedges
Walls
Stucco, stone (faux manufactured stone veneer is prohibited)
Fences21
Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)
Stucco wall finish shall be smooth trowel, with 1/2" to 3/4" bull-nosed corners.
Accent tile shall be 6" x 6" minimum.
Where used, "metal" and "wrought iron" shall be solid metal (not hollow tube).
Notes:
17
Applies to pitched roof forms; visible birdstops not allowed.
18
Required on façades facing rights-of-way and community open spaces.
19
Metal roll up doors are allowed only if not publicly visible. Metal security grilles are allowed for parking structures.
20
Allowed on façades not facing streets and community open spaces.
21
Chain link fences are prohibited within the EI Pueblo Viejo Landmark District. In other locations, publicly visible chain link fences are prohibited unless screened with vines.
2. 
Italian Mediterranean.
Element
Allowed Materials
Wall
Cladding
Stucco
Accent Materials
Tile, stone
Roof and Roof Elements
Roofing22
Two-piece (cap-and-pan) terra-cotta clay barrel tiles
Rake and Eave
Wood, composite wood, stucco
Cornice
Wood, composite wood, stucco, cast stone, fiberglass
Brackets and Corbels
Wood, composite wood, stucco, fiberglass
Parapet Cap
Stucco, two-piece (cap-and-pan) terra-cotta clay barrel tiles
Finials
Metal (copper, cast iron, steel)
Attic and Mechanical Vents
Vent
Masonry, terra-cotta clay barrel tiles, wood louvers, wrought iron grill
Gutters, Downspouts, and Leaderheads
Gutter Profile
Half-round
Downspout Profile
Round
Materials
Copper23, metal
Windows, Bay Windows, and Entry Doors
Entry Door
Wood, composite wood aluminum-clad wood, steel, fiberglass
Window Frames
Wood, aluminum-clad wood, steel
Door/Window Surrounds
Stucco, stone, cast stone, tile
Sill
Stucco, stone, cast stone
Glazing
Clear glass; shall not be tinted, mirrored, or colored
Garages
Garage Door24
Wood, composite wood, fiberglass
Balconies
Post, Handrail, Fascia, Railing, and Brackets
Wood, composite wood, cast stone, wrought iron, metal, fiberglass
Deck Soffit
Wood, composite wood, stucco, tile (glazed, terra-cotta), wrought iron, metal
Porches
Columns
Wood, composite wood, stucco, cast stone, metal, fiberglass
Railing
Wood, composite wood, cast stone, wrought iron, fiberglass
Storefronts
Storefront Module
Wood, composite wood, metal
Storefront Base (Bulkhead)
Stucco, tile
Chimneys
Cap
Stucco, terra-cotta clay barrel tiles, copper, steel
Body
Stucco, brick, stone, cast stone (including veneers of any of the above)
Exterior Building Lighting
Body and Mount
Wrought iron, metal
Shield
Clear, translucent, punched, louvers
Stairs and Ramps
Treads and Risers
Stucco, brick, stone, tile, concrete25
Handrails
Wood, composite wood, stucco, stone, wrought iron, metal
Trellises and Carports
Spanning Members
Wood
Trellis Posts
Wood
Carport Support Posts
Wood, composite wood, stucco,
Connections
Steel, iron
Trash Enclosure
Walls
Wood, composite wood, stucco
Fences and Hedges
Walls
Stucco, stone (faux manufactured stone veneer is prohibited)
Fences26
Wood, composite wood, wrought iron, metal, chain link (vinylcoated black or green)
Stucco wall finish shall be smooth trowel, with 1/2" to 3/4" bull-nosed corners.
Accent tile shall be 6" x 6" minimum.
Where used, "metal" and "wrought iron" shall be solid metal (not hollow tube).
Notes:
22
Applies to pitched roof forms; visible birdstops not allowed.
23
Required on façades facing streets and community open spaces.
24
Metal roll up doors are allowed only if not publicly visible. Metal security grilles (including roll up function) are allowed for parking structures.
25
Allowed on façades not facing streets and community open spaces.
26
Chain link fences are prohibited within the El Pueblo Viejo Landmark District. In other locations, publicly visible chain link fences are prohibited unless screened with vines.
(Ord. 6170, 2/25/2025)
A. 
General Description.
1. 
Contemporary Sub-Style. Contemporary style buildings have a sleek aesthetic and minimal ornamentation. This style focuses on combining simple rectilinear massing forms with changes in material and color. The use of glass and cantilevered elements imbues buildings with a sense of lightness and simplicity.
2. 
Industrial Sub-Style. The Industrial style similarly uses simple building forms, but utilizes gabled roof forms as well as flat roofs. Openings are simple and laid out in a rational manner. Thoughtful aging of industrial material, often metal, is allowed.
B. 
Character Description.
1. 
Contemporary.
Simple rectilinear massing volumes
Limited pushing and pulling of massing forms, delineated by changes in materials, colors, and finishes
Limited ornamentation and simple punched openings
Bay windows, awnings, balconies, and trellises used to break down façade and volume
2. 
Industrial.
Low- and medium-pitched or flat roofs with shallow eave or parapet
Simple gable roof forms
Horizontally proportioned opening made from ganged vertical windows
Elements of Contemporary Style
Example Building Elevation: Contemporary
C. 
Wall.
1. 
Contemporary.
Base
Base is not required for this sub-style.
Middle and Top
Cantilever without visually supportive column
6'-0" max. projection
Material changes may only occur at convex corners both vertical and horizontal.
Elements of Industrial Style
Example Building Elevation: Industrial
2. 
Industrial.
Trim1
Width
3" min.
A
Base
Height
1'-0" min.; 1/2 story max.
B
Required Articulation
Change in finish material
C
Base is required for this sub-style.
Middle and Top
Cantilever without visually supportive column
6'-0" max. projection
Material changes may only occur at convex corners both vertical and horizontal.
Note:
1
Trim not required on buildings or portions of buildings where stucco or stone is the primary wall material.
D. 
Building Roof: All.
Shed Roof Elevation
Building Roof Standards
Sloped Roof
Flat Roof
Roof Form
Type
Shed, Gable
Flat
Pitch
2:12 min.
8:12 max.
N/A
D
Applicable Subsections
E. Rake
Applies
N/A
F. Eave
Applies
N/A
G. Parapet
N/A
Applies
E. 
Rake.
Flush Rake Section
Projecting Rake Section
1. 
Contemporary.
Standards
Flush Profile
Projecting Profile
Horizontal Projection
No min.;
2'-6" min.;
2" max.
6'-0" max.
E
See Subsection F (Eave) for height standards.
2. 
Industrial.
Standards
Flush Profile
Projecting Profile
Horizontal Projection
No min.;
6" min.;
2" max.
1'-6" max.
E
See Subsection F (Eave) for height standards.
F. 
Eave: All.
Closed Eave Section
Open Eave Section
Standards
Open Eave
Closed Eave
Height
Fascia
6" min.
6" min.
F
Horizontal Projection2
Overall
1'-6" min.
N/A
G
Note:
2
Horizontal projection includes gutter.
G. 
Parapet.
Parapet Section
1. 
Contemporary.
Parapet Cap/Molding
Height
0" min.; 1'-0" max.
H
Horizontal Projection
0" min.; 3" max.
I
2. 
Industrial.
Parapet Cap/Molding
Height
0" min.; 6" max.
H
Horizontal Projection
0" min.; 3" max.
I
H. 
Windows.
Typical Window Elevation: Contemporary
Ganged Window Elevation: Contemporary
1. 
Contemporary.
Opening Proportion, Height
J
to Width
K
Typical Window
Ground Floor
11:5 min.
Typical Upper Floor
2:1 min.
Accent Window
Rectangle
3:2 min. (2'-6" max. width)
Square
1:1 min. (3'-0" max. width)
Ganged Window
3:5 min.
Picture Window
11:10 min.
Dormer Window
2:1 min.
Opening
Shape
Rectangular
Window
Operation
Double-Hung, Single-Hung, Awning, Casement, Fixed
Glazing Divisions
None required
Sash Widths
Rail
2" min.
L
Stile
2" min.
M
Trim Widths3
Head
2" min.
Jamb
2" min.
Apron
2" min.
Window Frame Recess
Depth
2" min. from face of sash
Sill Projection
Depth
2" min. from face of trim or surround
Pediment
Allowed
No
Mullions
Mullions required between ganged windows.
Note:
3
Trim required for windows only on buildings or parts of buildings with lap siding.
Typical Window Elevation with 12 Parts Glazing Division: Industrial
Ganged Window Elevation with 8 Parts and 12 Parts Glazing Divisions: Industrial
2. 
Industrial.
Opening Proportion, Height
N
to Width
O
Typical Window
Ground Floor
11:5 min.
Typical Upper Floor
2:1 min.
Accent Window
Rectangle
3:2 min. (2'-6" max. width)
Square
1:1 min. (3'-0" max. width)
Ganged Window
3:5 min.
Picture Window
11:10 min.
Dormer Window
2:1 min.
Opening
Shape
Rectangular
Window
Operation
Double-Hung, Single-Hung, Awning, Casement, Fixed
Glazing Divisions4
6 equal parts min.;
12 equal parts max.
Sash Widths
Rail
2" min.
P
Stile
2" min.
Q
Trim Widths5
Head
2" min.
R
Jamb
2" min.
S
Apron
None
Window Frame Recess
Depth
2" min. from face of sash
Sill Projection
Depth
2" min. from face of trim or surround
Pediment
Allowed
No
Mullions
Mullions required between ganged windows.
Notes:
4
Glazing divisions for picture windows may be one part.
5
Trim required for windows only on buildings or parts of buildings with lap siding.
I. 
Bay Windows: All.
Bay Window Plan
Bay Window Elevation
Form
Type
Square
Dimensions
Width
6'-0" min.; 12'-0" max.
T
Depth
8" min.; 4'-0" max.
U
Height Standards
Bay window may extend from second story to top story.
Bay window may occupy first story on buildings less than 3 stories tall.
Bay window form shall be vertically continuous from lowest bay window to highest bay window.
Allowed Cornice Treatments
Building parapet wraps bay window form.
Bay window stops below building eave (provide roof or cornice for bay window).
Bay window terminates into building eave (bay window form shall not project vertically or horizontally beyond building eave).
J. 
Dormers: All.
Dormer Elevation
Roof Form
Type
Shed
Pitch
2:12 min.; 6:12 max.
Horizontal Projection
Rake
See Subsection E (Rake) for rake standards.
Eave
See Subsection F (Eave) for eave standards.
Placement
Setback from Façade to Face of Dormer
1'-0" min.
Dormers shall not interrupt continuity of main building roof eave.
Window
See Subsection H (Windows) for window standards.
K. 
Entry Doors.
Vision Glass Door Elevation with Square Span
Half Glass Door Elevation with Sidelights
Full Glass Door Elevation with Transom
1. 
Contemporary.
Door
Number of Panels
0 min.
Lite Types/Glazing Divisions
Vision Glass
0 min.
Half Glass
0 min.
Full Glass
0 min.
Surround
Span Type
Square
Glazed Openings
Transom
Allowed
Sidelights
Allowed
2. 
Industrial.
Door
Number of Panels
0 min.
Lite Types/Glazing Divisions
Vision Glass
0 parts min.; 4 parts max.
Half Glass
4 parts min.
Full Glass
8 parts min.
Surround
Span Type
Square
Head Width
2" min.
V
Jamb Width
2" min.
W
Glazed Openings
Transom
Allowed
Sidelights
Allowed
L. 
Columns/Pilasters.
One-Story Porch: Contemporary
1. 
Contemporary
Columns + Pilasters
Shape
Square, Steel Section
Width/Diameter
6" min.; 4" min. for Steel Section
Spacing
8'-0" max. on center
X
Pedestal Height6
3'-0" min.
Columns must not span multiple stories
Additional Features
Paneling
Not Allowed
Fluting
Not Allowed
Note:
6
Pedestal may be omitted.
One-Story Porch with Square Columns on Pedestals: Industrial
2. 
Industrial.
Columns + Pilasters
Shape
Square, Steel Section
Width/Diameter
6" min.; 4" min. for Steel Section
Spacing
9'-6" min., 12'-0" max. on center
Y
Pedestal Height7
3'-0" min.
Z
Columns must not span multiple stories.
Additional Features
Paneling
Not Allowed
Fluting
Not Allowed
Entablature Height
Topmost Floor
1'-6" min.
A
Intermediate Floor
10" min.
Note:
7
Pedestal may be omitted.
M. 
Balconies: All.
Juliet Balcony with Horizontal Railing, Front Elevation
Balcony with Mesh Railing, Front Elevation
Balcony with Horizontal Railing, Front Elevation
Balcony with Panel Railing, Front Elevation
Allowed Types
Type 1 - Juliet Balcony
Inward-swinging door with full glazing required
B
Base Height
3" min.
C
Base Projection
4" min.; 2'-0" max.
Type 2 - Occupiable Balcony
Clear Depth
6'-0" min.
Cantilever without supporting columns
6'-0" max.
Area
48 sq. ft. min.
Recess into Façade
4'-6" max.
Overall Width
10'-0" max.
D
Guard/Railing
Allowed Types
Panel, Mesh, Horizontal
Height
Per Building Code
E
Width Between Posts
3'-0" min. on center
F
N. 
Store fronts: All.
Store Section
Storefront Elevation
Width
Storefront Module
10'-0" min.; 25'-0" max.
G
Display Window
3'-0" min.; 6'-0" max.
H
Glazing Divisions
None required
Distance Between Storefront Modules8
1'-0" min.; 4'-0" max.
I
Height
Overall
N/A
Head Height
10'-0" min.
J
Cornice
None
Signage Band
None
Bulkhead
0" min.; 2'-0" max.
K
Horizontal Recess
Depth
6" min.; 9" max.9
L
Bulkhead shall be continuous, unless divided by pilaster.
Notes:
8
May be expressed with pilasters. See Subsection L (Columns/Pilasters)
9
No max. depth for residential entries.
O. 
Awning.
Awning Section
Awning Elevation
1. 
Contemporary.
Awning Design
Horizontal Projection10
3'-0" min.
M
Offset from Opening
1'-0" max.
N
Required Support Elements
Structural metal, tubing, or cable
Note:
10
Horizontal projection includes gutter, where occurs.
P. 
Trellises and Carports: All.
Trellis Diagram
Dimensions
Wood
Metal
Post
8" x 8" min.
4" x 4" min.
O
Main and Cross Beam
4" x 8" min.11
2" x 4" min.
P
Rafter
2" x 4" min.
1.5" x 3" min.
Q
Purlin or Lattice
2" x 2" min.
1.5" x 1.5" min.
R
Overhang
S
Beams
3'-0" max.
Purlin or Lattice
2'-0" max.
Trellis
1'-6" max.
At balconies, overhangs may not project beyond balcony wall.
Note:
11
Paired 2" x 8" members are allowed when placed on both sides of the supporting posts.
Q. 
Materials.
1. 
Contemporary.
Element
Allowed Materials
Building Wall
Cladding
Lap siding (wood, composite wood, fiber cement), stucco, concrete, metal panel12
Base or Foundation
Base or Foundation
Wood, composite wood, stucco, brick, stone, concrete, fiber cement
Roof and Roof Elements
Roofing13
Shingles (composite wood, dimensional or luxury asphalt shingles to mimic the look of wood); standing seam metal (black, white, or reflective metal finishes are prohibited)
Rake and Eave
Wood, composite wood, steel
Gutter Profile
Box
Materials
Metal
Windows, Bay Windows, and Entry Doors
Entry Door
Wood, composite wood, metal, fiberglass
Window Frames
Wood, composite wood, aluminum-clad wood steel
Glazing
Clear glass; shall not be tinted, mirrored, or colored
Garages
Garage Door14
Wood, composite wood, metal, opaque glass
Balconies
Posts and Handrail
Metal
Railing
Metal panel, metal mesh, steel section, steel cable
Fascia
Wood, composite wood, metal
Porches
Columns
Wood, composite wood, metal, fiberglass
Railing
Wood, composite wood, metal panel, metal mesh, steel section, steel cable
Storefronts
Storefront Base (Bulkhead)
Wood, composite wood, concrete, metal panel, fiberglass
Exterior Building Lighting
Body and Mount
Wrought iron, metal
Shield
Clear, translucent, punched, louvers
Stairs and Ramps
Treads and Risers
Wood, composite wood, concrete, metal
Handrails
Wood, composite wood, metal
Trellises and Carports
Spanning Members
Wood, steel
Trellis Posts
Wood, steel
Carport Support Posts
Wood, composite wood, stucco, steel
Connections
Steel, iron
Trash Enclosure
Walls
Wood, composite wood, stucco
Fences and Hedges
Walls
Stucco, brick, stone (faux manufactured stone veneer is prohibited), concrete, concrete block (coated and painted or pigmented to match the main building)
Fences15
Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)
All ends of hollow steel members must be capped.
Notes:
12
Metal panel wall cladding is allowed only if used as an accent and not for the entire wall surface.
13
Applies to all pitched roofs and sloped roof parapets.
14
Metal roll up doors are allowed only if not publicly visible. Metal security grilles are allowed for parking structures.
15
Publicly visible fences may not be chain link unless screened with vines.
2. 
Industrial.
Element
Allowed Materials
Building Wall
Cladding
Lap siding (wood, composite wood, fiber cement), stucco, metal panel
Base or Foundation
Base or Foundation
Brick, concrete
Roof and Roof Elements
Roofing
Shingles (composite wood, dimensional or luxury asphalt shingles to mimic the look of wood); standing seam metal (black, white, or reflective metal finishes are prohibited)
Rake and Eave
Wood, composite wood, steel
Gutter Profile
Half-round, box
Materials
Metal
Windows, Bay Windows, and Entry Doors
Entry Door
Wood, composite wood, metal, fiberglass
Window Frames
Wood, aluminum-clad wood, steel
Glazing
Clear glass; shall not be tinted, mirrored, or colored
Garages
Garage Door16
Wood, composite wood, metal, opaque glass
Balconies
Posts
Metal
Railing
Metal panel, metal mesh, steel section, steel cable
Handrail
Wood, composite wood, metal
Fascia
Wood, composite wood, metal
Porches
Columns
Wood, composite wood, metal, fiberglass
Pedestal
Wood, composite wood, concrete, metal, fiberglass
Railing
Wood, composite wood, metal panel, metal mesh, steel section, steel cable
Storefronts
Storefront Base (Bulkhead)
Wood, composite wood, concrete, metal panel, fiberglass
Exterior Building Lighting
Body and Mount
Wrought iron, metal
Shield
Clear, translucent, punched, louvers
Stairs and Ramps
Treads and Risers
Metal, concrete
Handrails
Metal
Trellises and Carports
Spanning Members
Steel
Trellis Posts
Steel
Carport Support Posts
Steel
Connections
Steel
Trash Enclosure
Walls
Wood, composite wood, stucco
Fences and Hedges
Walls
Stucco, brick, stone (faux manufactured stone veneer is prohibited), concrete, concrete block (coated and painted or pigmented to match the main building)
Fences17
Wood, composite wood, wrought iron, metal, chain link (vinyl-coated black or green)
All ends of hollow steel members must be capped.
Notes:
16
Metal roll up doors are allowed only if not publicly visible. Metal security grilles (including roll up function) are allowed for parking structures.
17
Publicly visible fences may not be chain link unless screened with vines.
(Ord. 6170, 2/25/2025)