A. 
Alterations or relocations of watercourses.
(1) 
No encroachment, alteration or improvement of any kind shall be made to any watercourse until all adjacent municipalities which may be affected by such action have been notified by Lower Makefield Township, and until all required permits or approvals have been first obtained from the Department of Environmental Protection (PADEP) Regional Office.
(2) 
In addition, the Federal Emergency Management Agency (FEMA) and Pennsylvania Department of Community and Economic Development shall be notified by Lower Makefield Township prior to any alteration or relocation of any watercourse.
(3) 
No encroachment, alteration, or improvement of any kind shall be made to any watercourse unless it can be shown that the activity will not reduce or impede the flood-carrying capacity of the watercourse in any way.
B. 
Technical or scientific data shall be submitted by the applicant to FEMA for a letter of map revision (LOMR) as soon as practicable but within six months of any new construction, development, or other activity resulting in changes in the BFE. The situations when a LOMR or a conditional letter of map revision (CLOMR) are required are:
(1) 
Any development that causes a rise in the base flood elevations within the floodway; or
(2) 
Any development occurring in Zones A1-30 and Zone AE without a designated floodway, which will cause any rise in the base flood elevation; or
(3) 
Alteration or relocation of a stream (including but not limited to installing culverts and bridges).
C. 
The applicant shall (as per 44 CFR 65.12):
(1) 
Apply to FEMA for conditional approval of such action prior to permitting the encroachment to occur.
(2) 
Upon receipt of the Administrator's conditional approval of map change and prior to approving the proposed encroachments, Lower Makefield shall provide evidence to FEMA of the adoption of floodplain management ordinances incorporating the increased base flood elevations and/or revised floodway reflecting the post-project condition.
(3) 
Upon completion of the proposed encroachments, the applicant shall provide as-built certifications. FEMA will initiate a final map revision upon receipt of such certifications in accordance with 44 CFR Part 67.
D. 
Any new construction, development, uses or activities allowed within any Identified Floodplain Area shall be undertaken in strict compliance with the provisions contained in this chapter and any other applicable codes, ordinances and regulations.
E. 
Within any Identified Floodplain Area (see § 114-20), no new construction or development shall be located within the area measured 50 feet landward from the top-of-bank of any watercourse, unless a permit is obtained from the Department of Environmental Protection Regional Office.
Within any Identified Floodplain Area, any new construction or substantial improvements shall be prohibited. If a variance is obtained for new construction or substantial improvements in the Identified Floodplain Area in accordance with the criteria of in §§ 114-34 and 114-35, then the following provisions apply:
A. 
Residential structures.
(1) 
In AE, A1-30, and AH Zones, any new construction or substantial improvement shall have the lowest floor (including basement) elevated up to, or above, the regulatory flood elevation (the base flood elevation plus two feet of freeboard).
(2) 
In A Zones, where there are no base flood elevations specified on the FIRM, any new construction or substantial improvement shall have the lowest floor (including basement) elevated up to, or above, the regulatory flood elevation (the base flood elevation plus two feet of freeboard) determined in accordance with § 114-20C of this chapter.
(3) 
In AO Zones, any new construction or substantial improvement shall have the lowest floor (including basement) at or above the highest adjacent grade and at least two feet higher than the depth number specified on the FIRM.
(4) 
The design and construction standards and specifications contained in the 2021 International Building Code (IBC) and the 2021 International Residential Code (IRC) or the most recent revisions thereof and ASCE 24 and 34 Pa. Code (Chapters 401-405, as amended) shall be utilized, where they are more restrictive.
B. 
Nonresidential structures.
(1) 
In AE, A1-30 and AH Zones, any new construction or substantial improvement of a nonresidential structure shall have the lowest floor (including basement) elevated up to, or above, the regulatory flood elevation (the base flood elevation plus two feet of freeboard), or be designed and constructed so that the space enclosed below the regulatory flood elevation:
(a) 
Is floodproofed so that the structure is watertight with walls substantially impermeable to the passage of water; and
(b) 
Has structural components with the capability of resisting hydrostatic and hydrodynamic loads and the effects of buoyancy.
(2) 
In A Zones, where no base flood elevations are specified on the FIRM, any new construction or substantial improvement shall have the lowest floor (including basement) elevated or completely floodproofed up to, or above, the regulatory flood elevation (the base flood elevation plus two feet of freeboard) determined in accordance with § 114-20C of this chapter.
(3) 
In AO Zones, any new construction or substantial improvement shall have its lowest floor elevated or completely floodproofed above the highest adjacent grade and at least two feet higher than the depth number specified on the FIRM.
(4) 
Any nonresidential structure, or part thereof, made watertight below the regulatory flood elevation shall be floodproofed in accordance with the W1 or W2 space classification standards contained in the publication entitled "Flood-Proofing Regulations" published by the U.S. Army Corps of Engineers (June 1972, as amended in EP 1165-2-314, December 1995) or the flood load, and flood resistant construction requirements of ASCE. All plans and specifications for such floodproofing shall be accompanied by a statement certified by a registered professional engineer or architect which states that the proposed design and methods of construction are in conformance with the above-referenced standards. There should be a statement submitted with the permit application and a statement submitted with the as-built Floodproofing Certificate prior to the issuance of the Certificate of Occupancy.
(5) 
Prior to the issuance of the Certificate of Occupancy and in conjunction with the submission of the non-residential Floodproofing Certificate to the Floodplain Administrator, all non-residential structures that will be floodproofed must submit the following:
(a) 
An Inspection and Maintenance Plan detailing the annual maintenance of floodproofed components ensuring that all components will operate properly under flood conditions. Components that must be inspected include at a minimum:
[1] 
Mechanical equipment such as sump pumps and generators;
[2] 
Flood shields and closures;
[3] 
Walls and wall penetrations; and
[4] 
Levees and berms (as applicable).
(b) 
A Flood Emergency Operation Plan produced by the design professional detailing the procedures to be followed during a flooding event, which must include information pertaining to how all components will operate properly under all conditions, including power failures. An adequate plan shall include the following:
[1] 
An established chain of command and responsibility with leadership responsibilities clearly defined for all aspects of the plan.
[2] 
A procedure for notification of necessary parties there is a threat of flooding and/or flood warnings are issued. Personnel required to be at the building should have a planned and safe means of ingress and should have no other emergency response duties during a flood event. Alternates should be assigned if the primary persons responsible are unable to complete their assigned duties under the plan.
[3] 
A list of specific duties assigned to ensure that all responsibilities are addressed expeditiously. The locations of materials necessary to properly install all floodproofing components must be included in the list.
[4] 
An evacuation plan for all personnel or occupants; those without duties for the flood emergency as well as those with duties for implementing the plan. All possible ingress and egress routes must be identified.
(6) 
The design and construction standards and specifications contained in the 2021 International Building Code (IBC) and in the 2021 International Residential Code (IRC) or the most recent revisions thereof and ASCE 24 and 34 Pa. Code (Chapters 401-405, as amended) shall be utilized, where they are more restrictive.
C. 
Space below the lowest floor.
(1) 
Basements are prohibited.
(2) 
Fully enclosed space below the lowest floor (excluding basements) which will be used solely for the parking of a vehicle, building access, or incidental storage in an area other than a basement, shall be designed and constructed to allow for the automatic entry and exit of floodwaters for the purpose of equalizing hydrostatic forces on exterior walls. The term "fully enclosed space" also includes crawl spaces.
(3) 
Designs for meeting this requirement must either be certified by a registered professional engineer or architect, or meet or exceed the following minimum criteria:
(a) 
A minimum of two openings having a net total area of not less than one square inch for every square foot of enclosed space installed on two separate walls.
(b) 
The bottom of all openings shall be no higher than one foot above grade.
(c) 
Openings may be equipped with screens, louvers, or other coverings or devices, provided that they permit the automatic entry and exit of floodwaters.
(4) 
A nonconversion agreement is required to be recorded prior to issuance of the Certificate of Occupancy.
D. 
Historic structures. Historic structures undergoing repair or rehabilitation that would constitute a substantial improvement, as defined in this chapter, must comply with all ordinance requirements that do not preclude the structure's continued designation as a historic structure. Documentation that a specific ordinance requirement will cause removal of the structure from the National Register of Historic Places or the State Inventory of Historic Places must be obtained from the Secretary of the Interior or the State Historic Preservation Officer. Any exemption from ordinance requirements will be the minimum necessary to preserve the historic character and design of the structure.
E. 
Accessory structures. Structures accessory to a principal building need not be elevated or floodproofed to remain dry, but shall comply, at a minimum, with the following requirements:
(1) 
The structure shall not be designed or used for human habitation and shall be limited to the parking of vehicles, or to the storage of tools, material, and equipment related to the principal use or activity;
(2) 
The floor area shall not exceed 200 square feet;
(3) 
The structure will have a low damage potential;
(4) 
The structure will be located on the site so as to cause the least obstruction to the flow of floodwaters;
(5) 
Power lines, wiring, and outlets will be elevated to the Regulatory Flood Elevation;
(6) 
Permanently affixed utility equipment and appliances such as furnaces, heaters, washers, dryers, etc., are prohibited;
(7) 
Sanitary facilities are prohibited;
(8) 
The structure shall be adequately anchored to prevent flotation, collapse, and lateral movement and shall be designed to automatically provide for the entry and exit of floodwater for the purpose of equalizing hydrostatic forces on the walls. Designs for meeting this requirement must either be certified by a registered professional engineer or architect, or meet or exceed the following minimum criteria:
(a) 
A minimum of two openings having a net total area of not less than one square inch for every square foot of enclosed space;
(b) 
The bottom of all openings shall be no higher than one foot above grade; and
(c) 
Openings may be equipped with screens, louvers, etc., or other coverings or devices, provided that they permit the automatic entry and exit of floodwaters.
(9) 
For accessory structures that are 200 square feet or larger in area (footprint) and that are below the base flood elevation, a variance is required as set forth in §§ 114-34 and 114-35. If a variance is granted, a signed Declaration of Land Restriction (Non-conversion Agreement) shall be recorded on the property deed prior to issuance of the Certificate of Occupancy.
(10) 
The storage of hazardous materials in accessory structures within any Identified Floodplain Areas is prohibited.
The following minimum standards shall apply for all construction and development proposed within any Identified Floodplain Area:
A. 
Fill. Within any Identified Floodplain Area, the use of fill shall be prohibited. If a variance is obtained in accordance with the criteria in §§ 114-34 and 114-35, then the following provisions apply:
(1) 
Such fill shall not increase the base flood elevation.
(2) 
Fill shall extend laterally at least 15 feet beyond the building line from all points.
(3) 
Fill shall consist of soil or small rock materials only; sanitary landfills shall not be permitted.
(4) 
Fill shall be compacted to provide the necessary permeability and resistance to erosion, scouring, or settling.
(5) 
Fill shall be no steeper than one vertical to three horizontal, unless substantiated data justifying steeper slopes are submitted to, and approved by, the Zoning Officer, Floodplain Administrator and the Township Engineer.
(6) 
Fill shall be used to the extent to which it does not adversely affect adjacent properties.
(7) 
Under no circumstances shall fill be permitted in the floodway.
B. 
Drainage facilities. Storm drainage facilities shall be designed to convey the flow of stormwater runoff in a safe and efficient manner. The system shall ensure proper drainage along streets, and provide positive drainage away from buildings. The system shall also be designed to prevent the discharge of excess runoff onto adjacent properties.
C. 
Water and sanitary sewer facilities and systems.
(1) 
All new or replacement water and sanitary sewer facilities and systems shall be located, designed and constructed to minimize or eliminate flood damages and the infiltration of floodwaters.
(2) 
Sanitary sewer facilities and systems shall be designed to prevent the discharge of untreated sewage into floodwaters.
(3) 
No part of any on-site waste disposal system shall be located within any Identified Floodplain Area except in strict compliance with all state and local regulations for such systems. If any such system is permitted, it shall be located so as to avoid impairment to it, or contamination from it, during a flood.
(4) 
The design and construction provisions of the UCC and FEMA No. 348, "Protecting Building Utility Systems From Flood Damage," and the International Private Sewage Disposal Code shall be utilized.
(5) 
No expansion of any on-site sewage system now located either wholly or partially in the floodplain shall be permitted.
D. 
Other utilities. All other utilities such as gas lines, electrical and telephone systems shall be located, elevated (where possible) and constructed to minimize the chance of impairment during a flood.
E. 
Streets. The finished elevation of all new streets shall be no more than one foot below the regulatory flood elevation.
F. 
Storage. All materials that are buoyant, flammable, explosive or, in times of flooding, could be injurious to human, animal, or plant life, and not listed in § 114-27, Development which may endanger human life, shall be stored at or above the regulatory flood elevation or floodproofed to the maximum extent possible.
G. 
Placement of buildings and structures. All buildings and structures shall be designed, located, and constructed so as to not obstruct the flow of water and shall be designed to have no effect upon the flow and height of water.
H. 
Anchoring.
(1) 
All buildings and structures shall be firmly anchored in accordance with accepted engineering practices to prevent flotation, collapse or lateral movement. The Zoning Officer shall require the applicant to submit the signed and sealed certification by a registered professional engineer that the proposed structural design meets these criteria.
(2) 
All air ducts, large pipes, storage tanks, and other similar objects or components located below the regulatory flood elevation shall be securely anchored or affixed to prevent flotation.
I. 
Floors, walls and ceilings.
(1) 
Wood flooring used at or below the regulatory flood elevation shall be installed to accommodate a lateral expansion of the flooring, perpendicular to the flooring grain, without causing structural damage to the building.
(2) 
Plywood used at or below the regulatory flood elevation shall be of a marine or water-resistant variety.
(3) 
Walls and ceilings at or below the regulatory flood elevation shall be designed and constructed of materials that are water-resistant and will withstand inundation.
(4) 
Windows, doors, and other components at or below the regulatory flood elevation shall be made of metal or other water-resistant material.
J. 
Paints and adhesives.
(1) 
Paints or other finishes used at or below the regulatory flood elevation shall be of marine or water-resistant quality.
(2) 
Adhesives used at or below the regulatory flood elevation shall be of a marine or water-resistant variety.
(3) 
All wooden components (doors, trim, cabinets, etc.) used at or below the regulatory flood elevation shall be finished with marine or water-resistant paint or other finishing materials.
K. 
Electrical components.
(1) 
Electrical distribution panels shall be at least three feet above the base flood elevation.
(2) 
Separate electrical circuits shall serve lower levels and shall be dropped from above.
L. 
Equipment.
(1) 
Water heaters, furnaces, air conditioning and ventilating units, and other electrical, mechanical or utility equipment or apparatus shall not be located below the regulatory flood elevation.
(2) 
Ductwork shall be elevated to be at or above the regulatory flood elevation or floodproofed to remain water resistant.
M. 
Fuel supply systems. All gas and oil supply systems shall be designed to prevent the infiltration of floodwaters into the system and discharges from the system into floodwaters. Additional provisions shall be made for the drainage of these systems in the event that floodwater infiltration occurs.
N. 
Uniform construction code coordination. The standards and specifications contained 34 Pa. Code (Chapters 401-405), as amended, and not limited to the following provisions, shall apply to the above and other sections and subsections of this chapter, to the extent that they are more restrictive and supplement the requirements of this chapter:
(1) 
International Building Code (IBC) 2018 or the latest edition thereof: Sections 801, 1202, 1403, 1603, 1605, 1612, 3402, and Appendix G.
(2) 
International Residential Building Code (IRC) 2018 or the latest edition thereof: Sections R104, R105, R109, R322, Appendix E and Appendix J.
A. 
In accordance with the Pennsylvania Flood Plain Management Act,[1] and the regulations adopted by the Department of Community and Economic Development as required by the Act, any new or substantially improved structure which: will be used for the production or storage of any of the following dangerous materials or substances; or will be used for any activity requiring the maintenance of a supply of more than 550 gallons, or other comparable volume, of any of the following dangerous materials or substances on the premises; or will involve the production, storage, or use of any amount of radioactive substances, shall be prohibited. If a variance is obtained, the development shall be subject to the provisions of this chapter, in addition to all other applicable provisions. The following list of materials and substances are considered dangerous to human life:
(1) 
Acetone;
(2) 
Ammonia;
(3) 
Benzene;
(4) 
Calcium carbide;
(5) 
Carbon disulfide;
(6) 
Celluloid;
(7) 
Chlorine;
(8) 
Hydrochloric acid;
(9) 
Hydrocyanic acid;
(10) 
Magnesium;
(11) 
Nitric acid and oxides of nitrogen;
(12) 
Petroleum products (gasoline, fuel oil, etc.);
(13) 
Phosphorus;
(14) 
Potassium;
(15) 
Sodium;
(16) 
Sulphur and sulphur products;
(17) 
Pesticides (including insecticides, fungicides, and rodenticides);
(18) 
Radioactive substances, insofar as such substances are not otherwise regulated.
[1]
Editor's Note: See 32 P.S. § 679.101 et seq.
B. 
Within any Identified Floodplain Area, any new or substantially improved structure of the kind described in Subsection A, above, shall be prohibited within the area measured 50 feet landward from the top-of-bank of any watercourse.
C. 
Within any identified floodway area, any structure of the kind described in Subsection A, above, shall be prohibited.
D. 
Where permitted by variance within any other Identified Floodplain Area, any substantially improved residential structure of the kind described in § 114-27A, above, shall be elevated to remain completely dry up to at least two feet above the base flood elevation and built in accordance with §§ 114-24 through 114-26.
E. 
Substantially improved nonresidential structures.
(1) 
Where permitted within any Identified Floodplain Area, any substantially improved nonresidential structure of the kind described in § 114-27A, above, shall be built in accordance with §§ 114-24 through 114-26, including:
(a) 
Elevated or designed and constructed to remain completely dry up to at least two feet above the base flood elevation; and
(b) 
Designed to prevent pollution from the structure or activity during the course of a base flood.
(2) 
Any such structure, or part thereof, that will be built below the regulatory flood elevation shall be designed and constructed in accordance with the standards for completely dry floodproofing contained in the publication "Flood-Proofing Regulations" (U.S. Army Corps of Engineers, June 1972, as amended December 1995), or with some other equivalent watertight standard.
All subdivision proposals and development proposals containing at least 20 lots or at least five acres, whichever is the lesser, in Identified Floodplain Areas where base flood elevation data are not available, shall be supported by hydrologic and hydraulic engineering analyses that determine base flood elevations and floodway information. The analyses shall be prepared by a licensed professional engineer in a format required by FEMA for a Conditional Letter of Map Revision ("CLOMR") or Letter of Map Revision ("LOMR"). Submittal requirements and processing fees shall be the responsibility of the applicant.
Within any Identified Floodplain Area, manufactured homes shall be prohibited. If a variance is obtained in accordance with the criteria in §§ 114-34 and 114-35, then the following provisions apply:
A. 
Within any Floodway Area/District, manufactured homes shall be prohibited.
B. 
Within any Identified Floodplain Area, manufactured homes shall be prohibited within the area measured 50 feet landward from the top-of-bank of any watercourse.
C. 
Where permitted within any Identified Floodplain Area:
(1) 
All manufactured homes, and any improvements thereto, shall:
(a) 
Be placed on a permanent foundation.
(b) 
Be elevated so that the lowest floor of the manufactured home is at least two feet above the base flood elevation.
(c) 
Be anchored to resist flotation, collapse and lateral movement.
(2) 
Water heaters, furnaces, air conditioning and ventilating units, and other electrical, mechanical or utility equipment or apparatuses shall not be located below the Regulatory Flood Elevation and shall be anchored to resist flotation, collapse, and/or lateral movement.
(3) 
Ductwork shall be elevated to be at or above the Regulatory Flood Elevation or floodproofed to remain water resistant.
D. 
Installation of all manufactured homes shall be done in accordance with the manufacturer's installation instructions as provided by the manufacturer. Where the applicant cannot provide the above information, the requirements of Appendix E of the 2018 International Residential Building Code or the "U.S. Department of Housing and Urban Development's Permanent Foundations for Manufactured Housing," 1984 Edition, draft or latest revision thereto, and 34 Pa. Code Chapters 401 through 405 shall apply.
E. 
Consideration shall be given to the installation requirements of the 2021 IBC and the 2021 IRC or the most recent revisions thereto and 34 Pa. Code, as amended, where appropriate and/or applicable to units where the manufacturers' standards for anchoring cannot be provided or were not established for the proposed unit(s) installation.
Within any Identified Floodplain Area, recreational vehicles shall be prohibited. If a variance is obtained in accordance with the criteria in §§ 114-34 and 114-35, then the following provisions apply:
A. 
Recreational vehicles in Zones A, A1-30, AH and AE must either:
(1) 
Be on the site for fewer than 180 consecutive days;
(2) 
Be fully licensed and ready for highway use, which means the recreational vehicle or park model is on wheels or a jacking system, is attached to the site only by quick disconnect type utilities and security devices, and has no permanent attachments such as additions, rooms, stairs, decks, or porches; or
(3) 
Meet the permit requirements for manufactured homes in § 114-29.
In accordance with the administrative regulations promulgated by the Department of Community and Economic Development to implement the Pennsylvania Flood Plain Management Act, the following activities shall be prohibited within any Identified Floodplain Area:
A. 
The commencement of any of the following activities; or the construction, enlargement, or expansion of any structure used, or intended to be used, for any of the following activities:
(1) 
Hospitals.
(2) 
Nursing homes.
(3) 
Jails or prisons.
B. 
The commencement of, or any construction of, a new manufactured home park or manufactured home subdivision, or substantial improvement to an existing manufactured home park or manufactured home subdivision.