A. 
Applicability. Any application for a small wireless facility both inside and outside of the right-of-way shall comply with the application requirements for a small wireless facility permit described in this chapter. For small wireless facilities inside the right-of-way, the applicant must also comply with the requirements pursuant to Chapter 12.16 MCMC. The small wireless permits are issued by the director.
B. 
Consolidated Permits. All permits, leases, and franchises necessary for the deployment of small wireless facilities shall be consolidated for review and a decision rendered to the full extent feasible within the presumptively reasonable time periods established by federal law. Applicants are allowed to apply for franchises or leases independently of an application for a small wireless permit.
C. 
Pre-Application Meeting. A pre-application meeting is encouraged prior to submitting an application for a wireless communications facility permit.
D. 
Application Process. The director is authorized to establish franchise and other application forms to gather the information required by these ordinances from applicants and to determine the completeness of the application process as provided herein.
1. 
Franchise. The process typically begins with and depends upon approval of a franchise for the use of the public right-of-way to deploy small wireless facilities if any portion of the applicant’s facilities are to be located in the right-of-way, consistent with the requirements in Chapter 12.14 MCMC. An applicant with a franchise for the deployment of small wireless facilities in the city may proceed to directly apply for a small wireless facility permit and related approvals. An applicant may utilize phased development.
2. 
Small Wireless Facility Permits. The application requires specification of the small wireless facility components and locations as further required in the small wireless permit application described in subsection E of this section. Prior to the issuance of a small wireless facility permit, the applicant shall pay a permit fee as set forth in MCMC § 17.42.010.
3. 
Associated Permit(s). The applicant shall attach all associated permits such as applications or checklists required under the critical areas or SEPA ordinances. Applications for deployment of small wireless facilities on decorative poles or for new poles shall comply with the requirements in MCMC § 17.29.250.
4. 
Leases. An applicant who desires to attach a small wireless facility on any utility pole or light pole owned by the city shall include an application for a lease as a component of its application. Leases for the use of utility poles, light poles, or other public property, structures or facilities shall be submitted to the city council for approval.
E. 
Small Wireless Permit Application. The following information shall be provided by all applicants for a small wireless permit.
1. 
The application shall provide specific locational information including GIS coordinates of all proposed small wireless facilities and specify where the small wireless facilities will utilize existing, replacement or new poles, towers, existing buildings and/or other structures. Ground-mounted equipment, conduit, junction boxes and fiber and power connections necessary for and intended for use in the deployment shall also be specified regardless of whether the additional facilities are to be constructed by the applicant or leased from a third party. Detailed schematics and visual renderings of the small wireless facilities, including engineering and design standards, shall be provided by the applicant. The application shall have sufficient detail to identify:
a. 
The location of overhead and underground public utilities, telecommunication, cable, water, adjacent lighting, sewer drainage and other lines and equipment within 50 feet of the proposed project area (which the project area shall include the location of the signal source and power source). Further, the applicant shall include all existing and proposed improvements related to the proposed location, including but not limited to poles, driveways, ADA ramps, equipment cabinets, street trees and structures within 50 feet of the proposed project area.
b. 
The specific trees, structures, improvements, facilities, lines and equipment, and obstructions, if any, that applicant proposes to temporarily or permanently remove or relocate and a landscape plan for protecting, trimming, removing, replacing, and restoring any trees or areas to be disturbed during construction. The applicant is discouraged from trimming, removing or replacing trees, and if any such tree modifications are proposed the applicant must comply with MCMC § 12.16.1500.
c. 
The construction drawings shall also include the applicant’s plan for signal and power service, all conduits, cables, wires, handholes, junctions, meters, disconnect switches and any other ancillary equipment or construction necessary to construct the small cell facility, to the extent to which the applicant is responsible for installing such signal and power service, conduits, cables, and related improvements. Where another party is responsible for installing such signal and power service, conduits, cables, and related improvements, applicant’s construction drawings will include such utilities to the extent known at the time of application, but at a minimum applicant must indicate how it expects to obtain power and signal service to the small cell facility.
d. 
If the site location includes a new replacement light pole, then the applicant must submit a photometric analysis of the roadway and sidewalk within 150 feet of the existing light.
e. 
Compliance with the aesthetic requirements of MCMC § 17.29.260.
2. 
The applicant must show written approval from the owner of any pole or structure for the installation of its small wireless facilities on such pole or structure. Such written approval shall include approval of the specific pole, engineering and design standards, as well as assurances that the specific pole can withstand wind and seismic loads, from the pole owner, unless the pole owner is the city. Submission of the lease agreement between the owner and the applicant is not required. For city-owned poles or structures, the applicant must obtain a lease from the city prior to or concurrent with the small wireless permit application and must submit as part of the application the information required in the lease for the city to evaluate the usage of a specific pole.
3. 
The applicant is encouraged to batch the small wireless facility sites within an application in a contiguous service area.
4. 
Any application for a small wireless facility located in the right-of-way adjacent to a parcel zoned for residential use shall demonstrate that the applicant has evaluated the following:
a. 
Whether a small wireless facility is currently installed on an existing pole in front of the same residential parcel. If a small wireless facility exists, then the applicant must demonstrate that no technically feasible alternative location exists which is not in front of the same residential parcel.
b. 
Whether the proposed small wireless facility can be screened from residential view by choosing a pole location that is not directly in front of a window or views. The applicant must demonstrate that no technically feasible alternative location exists which is not directly in front of a window or views.
5. 
Any application for a small wireless permit which contains an element which is not exempt from SEPA review shall simultaneously apply under Chapter 43.21C RCW and Chapter 18.04 MCMC. Further, any application proposing small wireless facilities in critical areas (pursuant to Chapter 18.06 MCMC) must indicate that the application is exempt or comply with the review processes in such codes.
6. 
The applicant shall submit a sworn affidavit signed by an RF engineer with knowledge of the proposed project affirming that the small wireless facilities will be compliant with all FCC and other governmental regulations in connection with human exposure to radio frequency emissions for every frequency at which the small wireless facility will operate. If facilities which generate RF radiation necessary to the small wireless facility are to be provided by a third party, then the small wireless permit shall be conditioned on an RF certification showing the cumulative impact of the RF emissions on the entire installation. The applicant may provide one emissions report for the entire small wireless deployment if the applicant is using the same small wireless facility configuration for all installations within that batch or may submit one emissions report for each subgroup installation identified in the batch.
7. 
The applicant shall provide proof of FCC or other regulatory approvals required to provide the service(s) or utilize the technologies sought to be installed.
8. 
A professional engineer licensed by the state of Washington shall certify in writing, over his or her seal, that construction plans of the small wireless facilities and structure or pole and foundation are designed to reasonably withstand wind and seismic loads as required by applicable codes.
9. 
A traffic control plan as required by MCMC § 12.16.1400 and right-of-way work permit as required by MCMC § 12.16.1370.
10. 
Proof of a valid Mill Creek business license.
11. 
Recognizing that small wireless facility technology is rapidly evolving, the director is authorized to adopt and publish standards for the technological and structural safety of city-owned structures and to formulate and publish application questions for use when an applicant seeks to attach to city-owned structures.
12. 
Map showing all existing property lines within and adjacent to the proposed project and the names and mailing addresses in written and electronic format of the owners and residents of adjacent property.
13. 
Such other information as the director, in his/her discretion, shall deem appropriate to effectively evaluate the application based on technical, engineering and aesthetic considerations.
(Ord. 2019-850 § 4; Ord. 2025-943 § 2 (Exh. B))
A. 
Review. The following provisions relate to review of applications for a small wireless facility permit:
1. 
In any zone, upon application for a small wireless permit, the city will permit small wireless deployment on existing or replacement utility poles conforming to the city’s generally applicable development and design and concealment standards.
2. 
Vertical clearance shall be reviewed by the director to ensure that the small wireless facilities will not pose a hazard to other users of the right-of-way.
3. 
Replacement poles and new poles shall comply with the Americans with Disabilities Act (ADA), city construction and sidewalk clearance standards, traffic warrants, city ordinances, and state and federal statutes and regulations in order to provide a clear and safe passage within the right-of-way. Further, the location of any replacement pole or new pole must: be physically possible, cannot obstruct vehicular or pedestrian traffic or the clear zone, not interfere with utility or safety fixtures (e.g., fire hydrants, traffic control devices), and not adversely affect the public welfare, health, or safety.
4. 
No equipment shall be operated so as to produce noise in violation of Chapter 9.14 MCMC.
5. 
Small wireless facilities may not encroach onto or over private property or property outside of the right-of-way without the property owner’s express written consent.
B. 
Community Development Department. All small wireless facility deployment applications shall be reviewed by the director pursuant to MCMC § 14.09.010. The director’s decision shall be final and is appealable pursuant to Chapter 14.11 MCMC.
C. 
Eligible Facilities Requests. The design approved in a small wireless facility permit shall be considered concealment elements and such facilities may only be expanded upon submittal of an eligible facilities request described in MCMC § 17.29.050 when the modification does not defeat the concealment elements of the small wireless facility.
D. 
Review of Facilities. Review of the site locations proposed by the applicant shall be governed by the provisions of 47 USC 253 and 332 and other applicable statutes, regulations and case law. Applicants for franchises and the small wireless facility permits shall be treated in a competitively neutral and nondiscriminatory manner with other service providers, utilizing supporting infrastructure which is functionally equivalent; that is, service providers whose facilities are similarly situated in terms of structure, placement, or cumulative impacts. Small wireless facility permit review under this chapter shall neither prohibit nor have the effect of prohibiting the ability of an applicant to provide telecommunications services.
E. 
Withdrawal. Any applicant may withdraw an application submitted at any time, provided the withdrawal is in writing and signed by all persons who signed the original application or their successors in interest. When a withdrawal is received, the application shall be deemed null and void. If such withdrawal occurs prior to the director’s decision, then reimbursement of fees submitted in association with said application shall be prorated to with-hold the amount of city costs incurred in processing the application prior to time of withdrawal. If such withdrawal is not accomplished prior to the director’s decision, there shall be no refund of all or any portion of such fee.
F. 
Supplemental Information. Failure of an applicant to provide supplemental information as requested by the director within 60 days of notice by the director shall be deemed a denial of that application, unless an extension period has been approved by the director.
(Ord. 2019-850 § 4; Ord. 2024-928 § 2 (Exh. A))
A. 
The grantee of any permit shall comply with all of the requirements within the small wireless permit.
B. 
Post-Construction As-Builts. Upon request, the grantee shall provide the city with as-builts of the small wireless facilities, within 30 days after construction of the small wireless facility, demonstrating compliance with the permit and site photographs.
C. 
Permit Time Limit. Construction of the small wireless facility must be completed within 12 months after the approval date by the city. The grantee may request one extension to be limited to six months, if the applicant provides an explanation as to why the small wireless facility cannot be constructed within the original 12-month period.
D. 
Site Safety and Maintenance. The grantee must maintain the small wireless facilities in safe and working condition. The grantee shall be responsible for the removal of any graffiti or other vandalism and shall keep the site neat and orderly, including but not limited to following any maintenance or modifications on the site.
E. 
Operational Activity. The grantee shall commence operation of the small wireless facility no later than six months after installation. The applicant may request one extension for an additional six-month period if the applicant can show that such operational activity is delayed due to inability to connect to electrical or backhaul facilities.
(Ord. 2019-850 § 4)
A. 
If a grantee desires to make a modification to an existing small wireless facility, including but not limited to expanding or changing the antenna type, increasing the equipment enclosure, placing additional pole-mounted or ground-mounted equipment, or modifying the concealment elements, then the applicant shall apply for a small wireless facility permit.
B. 
A small wireless facility permit shall not be required for routine maintenance and repair of a small wireless facility within the right-of-way, or the replacement of an antenna or equipment of similar size, weight, and height; provided, that such replacement does not defeat the concealment elements used in the original deployment of the small wireless facility, does not impact the structural integrity of the pole, and does not require pole replacement. Further, a small wireless facility permit shall not be required for replacing equipment within the equipment enclosure or reconfiguration of signal or power to the small wireless facility. Right-of-way use permits may be required for such routine maintenance, repair or replacement consistent with Chapter 12.16 MCMC.
(Ord. 2019-850 § 4)
A. 
The issuance of a small wireless permit grants authority to construct small wireless facilities in the right-of-way in a consolidated manner to allow the applicant, in most situations, to avoid the need to seek duplicative approval by both the public works and the community development departments. If the applicant requires a new franchise to utilize the right-of-way, the franchise approval may be consolidated with the small wireless facility permit review if requested by the applicant. As an exercise of police powers pursuant to RCW 35.99.040(2), the small wireless facility permit is not a right-of-way use permit, but instead a consolidated public works and land use permit and the issuance of a small wireless facility permit shall be governed by the time limits established by federal law for small wireless facilities.
B. 
To the extent they do not conflict with the requirements of this chapter, the general standards applicable to the use of the right-of-way described in Chapter 12.16 MCMC shall apply to all small wireless facility permits.
(Ord. 2019-850 § 4; Ord. 2024-928 § 2 (Exh. A))
The city’s preference is for applicants to attach small wireless facilities to replacement light poles. If a light pole exists within 150 feet of a wooden pole, the applicant shall utilize the light pole unless the applicant can demonstrate, to the satisfaction of the director, that the light pole has been evaluated and is not possible for either technical feasibility or aesthetic reasons. However, this requirement shall not apply if the light pole is a decorative pole, as designated in MCMC § 17.29.250.
(Ord. 2019-850 § 4)
A. 
The city discourages the use of certain decorative poles for small wireless facilities due to the aesthetic impact to the city’s streetscape. Accordingly, the following types of poles (herein referred to as “decorative poles”) as designated in the standard specifications and details are discouraged from use for small wireless facilities: (1) architectural lighting commercial street light (LGT-4), (2) architectural lighting residential street light (LGT-5), and (3) candela commercial housing street light (LGT-6).
B. 
Applications for small wireless facilities attached to decorative poles must comply with MCMC § 17.29.270.
(Ord. 2019-850 § 4)
Small wireless facility deployments permitted in accordance with this chapter shall conform to the following design standards:
A. 
Small wireless facilities attached to existing or replacement non-wooden light poles and other non-wooden poles in the right-of-way or non-wooden poles outside of the right-of-way shall conform to the following design criteria:
1. 
Upon adoption of a city standard small wireless facility pole design(s) within the standard specifications and details, an applicant shall first consider using or modifying the standard pole design to accommodate its small wireless facility without substantially changing the outward visual and aesthetic character of the design. The applicant, upon a showing that use or modification of the standard pole design is either technically or physically infeasible, or that the modified pole design will not comply with the city’s ADA, sidewalk clearance requirements and/or would violate electrical or other safety standards, may deviate from the adopted standard pole design and use the design standards as further described in this subsection A.
2. 
The applicant shall minimize to the extent possible the antenna and equipment space and shall use the smallest amount of enclosure technically necessary to fit the equipment and antennas. The antennas and equipment shall be located using the following methods:
a. 
Concealed Completely within the Pole or Pole Base. Antennas and the associated equipment enclosures (including disconnect switches and other appurtenant devices) shall be fully concealed within the pole, unless such concealment is otherwise technically infeasible, or is incompatible with the pole design. If within the pole base, the base shall meet the ADA requirements and not impact the pedestrian access route.
b. 
Located on a Pole. If located on a pole, antennas and the associated equipment enclosures (including disconnect switches and other appurtenant devices) must be camouflaged to appear as an integral part of the pole.
i. 
The antenna(s) shall be placed as close to the surface of the pole as possible, but may not be more than 12 inches off the surface of the pole, and only if such distance is necessary for antenna tilt and technical need. Each antenna may not exceed three cubic feet in volume.
ii. 
The equipment shall be placed as close to the surface of the pole as possible, but may not be more than six inches off the surface of the pole. The equipment must be placed in the smallest enclosure possible for the technical need of the small wireless facility. The equipment enclosure and all other wireless equipment associated with the utility pole, including wireless equipment associated with the antenna (including conduit) and any pre-existing associated equipment on the pole, may not exceed 28 cubic feet. Multiple equipment enclosures may be acceptable if designed to more closely integrate with the pole design and do not cumulatively exceed 28 cubic feet. The applicant is encouraged to place the equipment enclosure behind any banners or road signs that may be on the pole; provided, that such location does not interfere with the operation of the banners or signs, or the operation of the small wireless facility.
iii. 
A unified antenna and equipment enclosure shall be placed as close to the surface of the pole as possible, but not more than 12 inches off the pole if necessary for antenna tilt and technical need. The unified equipment enclosure shall be the smallest size technically necessary, but shall not exceed the dimensional requirements of subsection (A)(2)(b)(ii) of this section.
iv. 
To the extent possible, the equipment enclosures shall be placed so as to appear as an integrated part of the pole or behind banners or signs; provided, that such location does not interfere with the operation of the banners or signs, or the operation of the small wireless facility.
v. 
The applicant may propose a side-mounted canister antenna, so long as the inside edge of the antenna is no more than six inches from the surface of the pole.
c. 
Underground in a Utility Vault. If located underground, the access lid to the equipment enclosure shall be located outside the footprint of any pedestrian curb ramp and shall have a nonskid surface meeting ADA requirement if located within an existing pedestrian access route.
d. 
On Private Property. If located on private property, the applicant shall provide documentation establishing the lease or easement right and permission of the property owner to locate the small wireless facility on the private property.
3. 
The furthest point of any equipment enclosure may not extend more than 28 inches from the face of the pole. Any equipment or antenna enclosures must meet WSDOT height clearance requirements. Applicants are encouraged to place the equipment enclosure as close to the antennas as physically and technically possible, unless such placement would cause a greater aesthetic impact.
4. 
All conduit, cables, wires and fiber must be routed internally in the non-wooden pole. Full concealment of all conduit, cables, wires and fiber is required within mounting brackets, shrouds, canisters or sleeves if attaching to exterior antennas or equipment.
5. 
An antenna on top of an existing pole may not extend more than six feet above the height of the existing pole and the diameter may not exceed 16 inches, measured at the top of the pole, unless the applicant can demonstrate that more space is technically necessary. The antennas shall be integrated into the pole design so that it appears as a continuation of the original pole, including colored or painted to match the pole, and shall be shrouded or screened to blend with the pole. All cabling and mounting hardware/brackets from the bottom of the antenna to the top of the pole shall be fully concealed and integrated with the pole.
6. 
Any replacement pole shall substantially conform to the design of the pole it is replacing or the neighboring pole design standards utilized within the contiguous right-of-way.
7. 
The height of any replacement pole may not extend more than 10 feet above the height of the existing pole or the minimum additional height necessary; provided, that the height of the replacement pole cannot be extended further by additional antenna height.
8. 
The diameter of a replacement pole shall comply with the city’s setback and sidewalk clearance requirements and shall, to the extent technically feasible, not be more than a 25 percent increase of the existing non-wooden pole measured at the base of the pole, unless additional diameter is needed in order to conceal equipment within the base of the pole, and shall comply with the requirements in subsection (E)(4) of this section.
9. 
The use of the pole for the siting of a small wireless facility shall be considered secondary to the primary function of the pole. If the primary function of a pole serving as the host site for a small wireless facility becomes unnecessary, the pole shall not be retained for the sole purpose of accommodating the small wireless facility and the small wireless facility and all associated equipment shall be removed.
B. 
Wooden Pole Design Standards. Small wireless facilities located on wooden poles shall conform to the following design criteria:
1. 
The wooden pole at the proposed location may be replaced with a taller pole for the purpose of accommodating a small wireless facility; provided, that the replacement pole shall not exceed a height that is a maximum of 10 feet taller than the existing pole, unless a further height increase is required and confirmed in writing by the pole owner and that such height extension is the minimum extension possible to provide sufficient separation and/or clearance from electrical and wireline facilities.
2. 
A pole extender may be used instead of replacing an existing pole but may not increase the height of the existing pole by more than 10 feet, unless a further height increase is required and confirmed in writing by the pole owner and that such height increase is the minimum extension possible to provide sufficient separation and/or clearance from electrical and wireline facilities. A “pole extender” as used herein is an object affixed between the pole and the antenna for the purpose of increasing the height of the antenna above the pole. The pole extender shall be painted to approximately match the color of the pole and shall substantially match the diameter of the pole measured at the top of the pole.
3. 
Replacement wooden poles must either match the approximate color and materials of the replaced pole or shall be the standard new wooden pole used by the pole owner in the city. Alternatively, the applicant may replace the wooden pole with a non-wooden pole upon the determination of the pole owner; provided, that the new pole is hollow and incorporates internal power and signal conduit for the small wireless facility.
4. 
Antennas, equipment enclosures, and all ancillary equipment, boxes and conduit shall be colored or painted to match the approximate color of the surface of the wooden pole on which they are attached.
5. 
Antennas shall not be mounted more than 12 inches from the surface of the wooden pole.
6. 
Antennas should be placed in an effort to minimize visual clutter and obtrusiveness. Multiple antennas are permitted on a wooden pole; provided, that each antenna enclosure shall not be more than three cubic feet in volume.
7. 
A canister antenna may be mounted on top of an existing wooden pole, which may not exceed the height requirements described in subsection (B)(1) of this section. A canister antenna mounted on the top of a wooden pole shall not exceed 16 inches in diameter, measured at the top of the pole, and shall be colored or painted to match the pole. The canister antenna must be placed to look as if it is an extension of the pole. In the alternative, the applicant may propose a sidemounted canister antenna, so long as the inside edge of the antenna is no more than 12 inches from the surface of the wooden pole. All cables shall be concealed either within the canister antenna or within a sleeve between the antenna and the wooden pole.
8. 
The furthest point of any antenna or equipment enclosure may not extend more than 28 inches from the face of the pole. Any equipment or antenna enclosures must meet WSDOT height clearance requirements.
9. 
An omni-directional antenna may be mounted on the top of an existing wooden pole, provided such antenna is no more than four feet in height and is mounted directly on the top of a pole or attached to a sleeve made to look like the exterior of the pole as close to the top of the pole as technically feasible. All cables shall be concealed within the sleeve between the bottom of the antenna and the mounting bracket.
10. 
All related equipment, including but not limited to ancillary equipment, radios, cables, associated shrouding, microwaves, and conduit which are mounted on wooden poles, shall not be mounted more than six inches from the surface of the pole, unless a further distance is technically required, and is confirmed in writing by the pole owner.
11. 
Equipment for small wireless facilities must be attached to the wooden pole, unless otherwise permitted to be ground-mounted pursuant to subsection (E)(1) of this section. The equipment must be placed in the smallest enclosure possible for the intended purpose. The equipment enclosure and all other wireless equipment associated with the utility pole, including wireless equipment associated with the antenna and any pre-existing associated equipment on the pole, may not exceed 28 cubic feet. Multiple equipment enclosures may be acceptable if designed to more closely integrate with the pole design and do not cumulatively exceed 28 cubic feet. The applicant is encouraged to place the equipment enclosure behind any banners or road signs that may be on the pole; provided, that such location does not interfere with the operation of the banners or signs.
12. 
An applicant who desires to enclose both its antennas and equipment within one unified enclosure may do so; provided, that such enclosure is the minimum size necessary for its intended purpose and the enclosure and all other wireless equipment associated with the pole, including wireless equipment associated with the antenna and any pre-existing associated equipment on the pole, does not exceed 28 cubic feet. The unified enclosure may not be placed more than six inches from the surface of the pole, unless a further distance is required and confirmed in writing by the pole owner. To the extent possible, the unified enclosure shall be placed so as to appear as an integrated part of the pole or behind banners or signs; provided, that such location does not interfere with the operation of the banners or signs.
13. 
The visual effect of the small wireless facility on all other aspects of the appearance of the wooden pole shall be minimized to the greatest extent possible.
14. 
The use of the wooden pole for the siting of a small wireless facility shall be considered secondary to the primary function of the pole. If the primary function of a pole serving as the host site for a small wireless facility becomes unnecessary, the pole shall not be retained for the sole purpose of accommodating the small wireless facility and the small wireless facility and all associated equipment shall be removed.
15. 
The diameter of a replacement pole shall comply with the city’s setback and sidewalk clearance requirements.
16. 
All cables and wires shall be routed through conduit along the outside of the pole. The outside conduit shall be colored or painted to match the pole. The number of conduits shall be minimized to the number technically necessary to accommodate the small wireless facility.
C. 
Small wireless facilities attached to existing buildings shall conform to the following design criteria:
1. 
Small wireless facilities may be mounted to the sides of a building if the antennas do not interrupt the building’s architectural theme.
2. 
The interruption of architectural lines or horizontal or vertical reveals is discouraged.
3. 
New architectural features such as columns, pilasters, corbels, or other ornamentation that conceal antennas may be used if they complement the architecture of the existing building.
4. 
Small wireless facilities shall utilize the smallest mounting brackets necessary in order to provide the smallest offset from the building.
5. 
Skirts or shrouds shall be utilized on the sides and bottoms of antennas in order to conceal mounting hardware, create a cleaner appearance, and minimize the visual impact of the antennas. Exposed cabling/wiring is prohibited.
6. 
Small wireless facilities shall be colored, painted and textured to match the adjacent building surfaces, to the extent technically feasible.
D. 
Small wireless facilities mounted on cables strung between existing utility poles shall conform to the following standards:
1. 
Each strand-mounted facility shall not exceed three cubic feet in volume, unless the applicant can demonstrate, to the satisfaction of the director, that the three cubic feet maximum is technically infeasible;
2. 
Only one strand-mounted facility is permitted per cable between any two existing poles;
3. 
The strand-mounted devices shall be placed as close as possible to the nearest utility pole, in no event more than five feet from the pole unless a greater distance is technically necessary or is required by the pole owner for safety clearance;
4. 
No strand-mounted device shall be located in or above the portion of the roadway open to vehicular traffic;
5. 
Ground-mounted equipment to accommodate a shared mounted facility is not permitted except when placed in pre-existing equipment cabinets;
6. 
Pole-mounted equipment shall comply with the requirements of subsections A and B of this section;
7. 
Such strand-mounted devices must be installed to cause the least visual impact and without excess exterior cabling or wires (other than the original strand); and
8. 
Strand-mounted facilities are prohibited on non-wooden poles, unless the existing pole has pre-existing communication wirelines.
E. 
General Requirements.
1. 
Ground-mounted equipment in the right-of-way is prohibited, unless the applicant can demonstrate that pole-mounted or undergrounded equipment is technically infeasible. If ground-mounted equipment is necessary, then the applicant shall submit a concealment element plan. Generators located in the right-of-way are prohibited.
2. 
No equipment shall be operated so as to produce noise in violation of Chapter 9.14 MCMC.
3. 
Small wireless facilities are not permitted on traffic signal poles unless denial of the siting could be a prohibition or effective prohibition of the applicant’s ability to provide telecommunications service in violation of 47 USC 253 and 332.
4. 
Small wireless facilities are not permitted on bollard or pedestrian path lighting.
5. 
Replacement poles and new poles shall comply with the Americans with Disabilities Act (ADA), city construction and sidewalk clearance standards, city ordinance, and state and federal laws and regulations in order to provide a clear and safe passage within the right-of-way. Further, the location of any replacement or new pole must: be physically possible, comply with applicable traffic warrants, not interfere with utility or safety fixtures (e.g., fire hydrants, traffic control devices), and not adversely affect the public welfare, health or safety.
6. 
Replacement poles shall be located as near as possible to the existing pole with the requirement to remove the abandoned pole.
7. 
No signage, message or identification other than the manufacturer’s identification or identification required by governing law is allowed to be portrayed on any antenna or equipment enclosure. Any permitted signage shall be located on the equipment enclosures and be of the minimum amount possible to achieve the intended purpose (no larger than four by six inches); provided, that signs are permitted as concealment element techniques where appropriate.
8. 
Antennas and related equipment shall not be illuminated except for security reasons, required by a federal or state authority, or unless approved as part of a concealment element plan.
9. 
Side arm mounts for antennas or equipment must be the minimum extension necessary and the inside edge of the antenna may be no more than 12 inches from the surface of the pole.
10. 
The preferred location of a small wireless facility on a pole is the location with the least visual impact.
11. 
Antennas, equipment enclosures, and ancillary equipment, conduit and cable shall not dominate the structure or pole upon which they are attached.
12. 
Except for locations in the right-of-way, small wireless facilities are not permitted on any property containing a residential use in the residential zones.
13. 
The city may consider the cumulative visual effects of small wireless facilities mounted on poles within the right-of-way when assessing proposed siting locations so as to not adversely affect the visual character of the city. This provision shall not be applied to limit the number of permits issued when no alternative sites are reasonably available nor to impose a technological requirement on the applicant.
14. 
These design standards are intended to be used solely for the purpose of concealment and siting. Nothing herein shall be interpreted or applied in a manner which dictates the use of a particular technology. When strict application of these requirements would unreasonably impair the function of the technology chosen by the applicant, alternative forms of concealment or deployment may be permitted which provide similar or greater protections from negative visual impacts to the streetscape.
(Ord. 2019-850 § 4)
A. 
New poles within the right-of-way or for installations on a decorative pole are only permitted if the applicant can establish that:
1. 
The proposed small wireless facility cannot be located on an existing utility pole or light pole, electrical transmission tower or on a site outside of the public right-of-way such as a public park, public property, building, transmission tower or in or on a nonresidential use in a residential zone whether by roof or panel-mount or separate structure;
2. 
The proposed small wireless facility complies with the applicable requirements of MCMC § 17.29.260(E);
3. 
The proposed small wireless facility receives approval for a concealment element design, as described in subsection C of this section;
4. 
The proposed small wireless facility complies with SEPA, if applicable; and
5. 
No new poles shall be located in a critical area or associated buffer required by the city’s critical areas management ordinance (Chapter 18.06 MCMC), except when determined to be exempt pursuant to said ordinance.
B. 
An application for a new pole or installation on a decorative pole is subject to review and approval or denial by the director.
C. 
The concealment element design shall include the design of the screening, fencing or other concealment technology for a tower, pole, or equipment structure, and all related transmission equipment or facilities associated with the proposed small wireless facility, including but not limited to signal and power connections.
1. 
If the applicant desires to place the small wireless facility on a decorative pole, and the city has created a small wireless facility standard for such type of decorative pole in the standard specification and details, then the applicant is encouraged to first consider using the decorative pole design adopted for small wireless facilities from the standard specification and details. The applicant, upon a showing that using the standard decorative pole design is either technically or physically infeasible, or that a modified pole design will not comply with the city’s ADA or sidewalk clearance requirements and/or would violate electrical or other safety standards, may deviate from the adopted standard decorative pole design and propose a concealment element design consistent with subsection (C)(2) of this section.
2. 
If the director has already approved a concealment element design either for the applicant or another small wireless facility along the same public right-of-way or for the same pole type, then the applicant shall utilize a substantially similar concealment element design, unless it can show that such concealment element design is not physically or technically feasible, or that such deployment would undermine the generally applicable design standards; in such case, the applicant shall propose a concealment element design consistent with subsection (C)(3) of this section.
3. 
The concealment element design should seek to minimize the visual obtrusiveness of the small wireless facility. The proposed pole or structure should have similar designs to existing neighboring poles in the right-of-way, including similar height to the extent technically feasible. If the proposed small wireless facility is placed on a replacement pole, then the replacement pole shall be of the same general design as the pole it is replacing (for example if a candela commercial housing street light, then the replacement pole should match that pole design), unless the community development department otherwise approves a variation due to aesthetic or safety concerns. Any concealment element design for a small wireless facility should attempt to mimic the design of such pole and integrate the small wireless facility into the design of the pole. Other concealment methods include, but are not limited to, integrating the installation with architectural features or building design components, utilization of coverings or concealment devices of similar material, color, and texture – or the appearance thereof – as the surface against which the installation will be seen or on which it will be installed, landscape design, or other camouflage strategies appropriate for the type of installation. Applicants are required to utilize designs in which all conduit and wirelines are installed internally in the structure.
D. 
Even if an alternative location is established pursuant to subsection (A)(1) of this section, the director may determine that a new pole in the right-of-way is in fact a superior alternative based on the impact to the city, the concealment element design, the city’s comprehensive plan and the added benefits to the community.
E. 
Prior to the issuance of a permit to construct a new pole or ground-mounted equipment in the right-of-way, the applicant must obtain a site-specific agreement from the city to locate such new pole or ground-mounted equipment. This requirement also applies to replacement poles when the replacement is necessary for the installation or attachment of small cell facilities, the replacement structure is higher than the replaced structure, and the overall height of the replacement structure and the small cell facility is more than 60 feet.
F. 
These design standards are intended to be used solely for the purpose of concealment and siting. Nothing herein shall be interpreted or applied in a manner which dictates the use of a particular technology. When strict application of these requirements would unreasonably impair the function of the technology chosen by the applicant, alternative forms of concealment or deployment may be permitted which provide similar or greater protections of the streetscape.
(Ord. 2019-850 § 4; Ord. 2024-928 § 2 (Exh. A))