If an applicant submits a conservation subdivision application, the preliminary plat approval requirement is waived and the applicant shall proceed directly to final approval process described in Article
VII, Final Plat Review, of this chapter.
A preliminary plat shall be prepared by a licensed
land surveyor or engineer, at a scale of one inch equals 100 feet
and shall include information shown on the approved sketch plat including:
C. Name of the property owner.
D. Name, address and telephone number of the New York
State licensed engineer or surveyor preparing the preliminary plat.
E. Description.
(1) North arrow showing true north.
(2) Tax map section, block and lot numbers.
(3) Distance to the nearest existing or platted streets,
street intersections, or other public ways within or immediately adjacent
to the tract.
(4) All utilities, available and/or proposed, including
easements therefor, and all streets which are either existing, proposed,
or shown on the Official Map, if any.
(5) Zoning district, including exact boundary lines of the district, if more than one district, and any proposed changes in the zoning district lines and/or the requirements of Chapter
280, Zoning, applicable to the subdivision.
(6) Name of any subdivisions immediately adjacent to the
parcel and the name of the owners of record of all adjacent property.
(7) Land areas proposed to be dedicated to public use
and the conditions of such dedication.
F. Existing easements, covenants and/or restrictions,
including liber and page number.
G. Existing and proposed improvements.
(1) Location of any existing sewers, water mains, culverts
and drains on the property, with pipe sizes, grades and direction
of flow.
(2) Width and location of any streets or public ways or
places shown on the Official Map or Master Plan, if such exists, within
the area to be subdivided, and the width, location, grades and street
profiles of all streets or public ways proposed by the applicant.
(3) Approximate location and size of any proposed water
lines, valves, hydrants and sewer lines, and fire alarm boxes; connection
to existing lines or alternate means of water supply or sewage disposal
and treatment as provided in the Public Health Law or Environmental
Conservation Law; profiles of all proposed water and sewer lines.
(4) Storm drainage plan showing the approximate location
and size of proposed lines and their profiles; connection to existing
lines or alternate means of disposal.
(5) Plans and cross sections showing the proposed location
and type of any sidewalks, streetlighting standards, street trees,
curbs, water mains, sanitary sewers and storm drains, and the size
and type thereof; the character, width and depth of pavements and
subbase, the location of manholes, basins and underground conduits.
(6) Preliminary designs of any bridges or culverts which
may be required.
H. Preliminary road and drainage plan. The developer
shall submit six copies of the road and drainage plans showing all
typical plans, sections, profiles, details and design calculations
as needed or required to indicate the proposed construction and/or
development.
(1) Road and drainage plans shall show all metes and bounds descriptions indicating street and drainage areas as well as the size and type of road systems pursuant to Chapter
161, Highway Specifications, of the Code.
(2) Where indicated or required, road and drainage plans
shall include but not be limited to the following:
(a)
Metes and bounds descriptions of all building
lots indicating lot areas, proposed building envelopes and scenic
buffer areas.
(b)
Utilities: indicate size and location of all
below-grade utilities, including proposed water mains, electrical
conduit and transformer pads.
(c)
Fire wells or fire hydrants.
(d)
The limits of all tidal and freshwater wetlands
within 100 feet of the proposed development.
(e)
Topographical contours at an interval that will
accurately depict the slope and contour of the site.
(f)
Road profiles and typical cross-sections.
(g)
Drainage calculations and design indicating
all drainage structures and piping.
(h)
Test hole and boring data.
(i)
All existing and proposed easements indicating
width, area and purpose.
(j)
Concrete survey monuments.
(n)
Street trees, including size, type and specifications
for placement.
(o)
Street signs, indicating type and location.
(3) A stormwater management control plan consistent with the requirements of Chapter
236, Stormwater Management, of this Code. The stormwater management control plan shall meet the performance and design criteria and standards in Chapter
236, Stormwater Management.
[Added 2-14-2012 by L.L. No. 3-2012]
The Planning Board shall comply with the provisions
of the State Environmental Quality Review Act (SEQRA) and its implementing
regulations. A preliminary plat application shall not be considered
complete until a negative declaration has been filed or until a notice
of completion of the draft environmental impact statement has been
filed in accordance with the provisions of SEQRA. The time periods
for review of a preliminary plat shall begin upon filing of such negative
declaration or such notice of completion.