In expansion of the declaration of legislative intent and statement of community development objectives found in §§
500-101 and
500-102 of Article
I of this chapter, it is the intent of this article to provide regulations for agricultural and low-density residential uses in conformance with the goals of the Comprehensive Plan, Open Space and Environmental Resource Protection Plan, and the following objectives:
A. Establish reasonable standards that permit the continued
operation of agricultural uses while allowing limited development
of single-family detached dwelling units.
B. Direct lower-density residential development to areas
of the Township that are more rural in character and less likely to
be served by the extension of centralized sewer and water system networks.
C. Provide minimum lot dimensions which are compatible
with the need to provide on-site water supply and sewage disposal.
D. Provide standards and criteria for R-1 development
in appropriate areas of the Township in accordance with the Upper
Perkiomen Valley Regional Comprehensive Plan.
[Amended 12-9-2003 by Ord. No. 03-12]
[Added 1-8-2019 by Ord.
No. 2019-01]
Group homes. Group homes, as defined in §
500-201, are permitted by conditional use in the R-1 zoning district. In addition to any general criteria for conditional uses set forth elsewhere in the zoning ordinance, the conditional use applicant shall satisfy the following criteria at the time of hearing:
A. The
proposed use shall be consistent with the character of the zoning
district and neighborhood;
B. The
residents must live together in what is functionally a household,
eating together, socializing together, and integrating into the community;
C. The proposed use satisfies the definition set forth in §
500-201 and it is demonstrated that the proposed use is not a medical facility.
[Amended 8-14-2001 by Ord. No. 01-08; 12-13-2005 by Ord. No.
2005-13]
A. Criteria for single-family detached dwellings:
(1)
Maximum allowed density.
[Amended 6-10-2008 by Ord. No. 2008-04]
(a)
The maximum allowed number of lots to be subdivided
for single-family detached dwelling units shall be determined at a
rate of one dwelling unit per two acres of developable lot area of
the tract (any remainder less than a full two acres shall be disregarded
in the density calculation).
(b)
Potential inability to develop the maximum numbers
of dwelling units. The applicant's choice of dwelling style, physical
constraints of the development site, or other factors may limit the
applicant's ability to develop the maximum number of dwelling units
permitted by the calculations herein. The applicant's plans shall
still be required to comply with all applicable requirements of the
R-1 District, including the minimum open space. In short, the maximum
allowed density is not guaranteed.
(2)
Minimum lot area, width and yards.
(a)
Lot area: 50,000 square feet, subject to maximum
allowed density determined per above criteria.
[Amended 6-10-2008 by Ord. No. 2008-04]
(c)
Minimum road frontage: 50 feet; see §
500-813 herein.
(e)
Side yards: 40 feet minimum, 100 feet aggregate.
(3)
Maximum height.
[Amended 8-8-2023 by Ord. No. 2023-02]
(a)
The height of a structure shall be determined in accordance with §
500-832.
(b)
The maximum height of a residence is 35 feet, excluding mechanical
penthouses the height of which are determined with reference to the
International Building Code. Accessory buildings may be 25 feet in
height. Any nonresidential building height in excess of 35 feet requires
conditional use approval by the Board of Supervisors. In considering
an application for conditional use related to building height, the
Board of Supervisors shall consider the following factors:
[1] The nature of the building itself and the extent
to which it is consistent or inconsistent with the landscape and structures
in the vicinity of it;
[2] The height of other buildings in the area;
[3] The proximity of residences and the extent to which
the height of the building diminishes the quality of life for those
residing in proximity to the building, also considering topography
and the extent to which the building is visible from nearby residences;
[4] Whether the building will include a mechanical
penthouse that is excluded from the definition of building height;
[5] The extent to which the requirements, standards
or common practices associated with a particular proposed use require
a building that is more than 35 feet tall;
[6] Whether the increased building height will increase
the impact of the use of the building with respect to noise, traffic
volume, light spillover, or similar community impacts.
(4)
Minimum setbacks for accessory buildings.
[Amended 9-13-2016 by Ord. No. 2016-04]
(a)
Private garages and other storage buildings with a building footprint of 400 square feet or greater shall comply with §
500-808B of this chapter.
(b)
Buildings up to and including 15 feet in height:
[1]
Front yard: Not permitted.
(c)
Buildings over 15 feet in height:
[1]
Front yard: Not permitted.
[2]
Side yard: 15 feet plus two feet for every one foot or part
thereof in building height over 15 feet.
[3]
Rear yard: 15 feet plus two feet for every one foot or part
thereof in building height over 15 feet.
(5)
Maximum building coverage. The maximum building
coverage is 10%.
(6)
Minimum open space. When a subdivision involves
more than four lots (including lots which will contain existing dwellings),
a minimum acreage equal to 15% of the gross lot area of the tract
shall be set aside as open space.
B. Criteria for agriculture.
(1)
Minimum lot area, width and yards.
(c)
Minimum road frontage: 50 feet; see §
500-813 herein.
(d)
Yards. Minimum setbacks for agricultural buildings shall comply with §
500-808 of this chapter.
(2)
Maximum height. The maximum height shall comply with §
500-831 of this chapter.
(3)
Maximum building coverage. The maximum building
coverage is 20%.
[Amended 3-9-2004 by Ord. No. 2004-01]
Open space/cluster development shall be permitted as a design alternative in this district. Where there are differences in permitted uses and dimensional standards between this section and §§
500-1201 and
500-1202, the provisions of this section shall apply.
A. Application.
[Amended 3-10-2015 by Ord. No. 2015-04]
(1) Purposes.
The primary purpose of these standards is to preserve the Hosensack
Creek Greenway as identified in Figure 12-1 of the 1995 Joint Open
Space and Environmental Resource Protection Plan and to facilitate
acquisition of properties listed as first and second priorities in
said plan, while permitting limited levels of subdivision and/or land
development that are compatible with those purposes. A secondary purpose
is to encourage preservation of properties listed in the Open Space
Plan as "historic farmstead or houses restored or with restoration
potential."
(2) Identification
of applicable properties: parcels of land in the R-1 Agricultural
- Low Density Residential District north of Route 29, that are identified
as "acquisition and linkage top priorities" in Figure 12-3 or "overall,
general priorities for acquisition of lands, easements, rights-of-way"
in Figure 12-1 of the 1995 Joint Open Space and Environmental Resource
Protection Plan.
B. Qualifying tract.
(1)
Minimum tract size: five acres.
(2)
Centralized sewer and water shall be provided.
(3)
A minimum of 50% of the gross area of the development
shall be set aside as common open space.
[Amended 10-11-2005; by Ord. No. 2005-13]
C. Density standards.
[Amended 10-11-2005; by Ord. No. 2005-13]
(1)
The overall gross residential density of the
open space/cluster development shall be based on:
(a)
One unit per two acres of developable area for
developments providing the minimum fifty-percent open space requirement
(see Figure 12.1).
(b)
One unit per two acres of developable area multiplied
by the following bonus multiplier — for each percent
of open space provided between 50% and 60%, a bonus multiplier of
0.025 for each percent up to a bonus multiplier of 1.25% — for
developments providing 60% open space (see Figure 12.1).
(2)
The area that is not used for development shall
be set aside as common open space.
(3)
The permitted number of lots shall be calculated
using the Permitted Lots Worksheet, Figure 12.1. A copy of the completed
worksheet shall be placed on the subdivision plan as evidence of the
calculations.
D. Minimum lot area, lot width, and yards for residential
buildings:
|
|
Single-Family Detached
|
Lot Line or Village
|
---|
|
Lot area, per dwelling unit (DU)
|
10,000 square feet
|
6,000 square feet
|
|
Lot width at building line, per DU
|
100 feet
|
60 feet
|
|
Front yard (from ultimate right-of-way)
|
35 feet
|
20 feet
|
|
Rear yard
|
35 feet
|
20 feet
|
|
Side yard
|
15 feet, one side
30 feet, aggregate
|
15 feet, one side
30 feet, aggregate
|
|
Setback from each street that lot abuts (from
ultimate right-of-way)
|
35 feet
|
20 feet
|
|
Building coverage
|
18%
|
25%
|
|
Impervious coverage
|
30%
|
40%
|
E. Density and dimensional standards for development.
The outer boundaries of all developments shall meet the following
setbacks:
(1)
From external arterial road ultimate right-of-way
or from scenic roads: 200 feet.
(2)
From all other external road ultimate right-of-way:
100 feet.
(3)
From all tract boundaries: 100 feet.
(4)
From cropland or pasture land: 100 feet.
(5)
From buildings or barnyards housing livestock:
300 feet.
(6)
From other residential neighborhoods: 100 feet.
(7)
From wetlands, floodplains, or watercourses:
as per chapter.
(8)
From active recreation areas such as courts
or playing fields: 150 feet.
(9)
All setback areas along roads shall be landscaped according to the standards of Chapter
425, Subdivision and Land Development, in order to preserve scenic views and integrate the neighborhood into the surrounding landscape.
(10)
Setback standards may be reduced by the Board
of Supervisors under the following circumstances:
(a)
Setbacks from roads may be reduced to a minimum
of 50 feet if the applicant can demonstrate that existing vegetation
and/or topography form an effective visual buffer along these roads.
(b)
All other setbacks may be reduced to 1/2 of
the requirement specified above if the applicant can demonstrate that
reduced setbacks improve the plan's compliance with the intent of
this chapter.
F. Setbacks for agricultural buildings and structures and private garages shall comply with §
500-808 of this chapter.
G. Minimum setbacks for buildings and structures (except
private garages) that are accessory to a residential use:
(1)
Buildings and structures up to 15 feet in height:
10 feet from side and rear property lines; not permitted in the front
yard setback.
(2)
Buildings and structures over 15 feet in height:
10 feet from side and rear property lines plus two additional feet
for each one foot or part thereof in excess of 15 feet. Maximum required
setback: 25 feet; not permitted in the front yard setback.
H. Maximum permitted height for buildings and structures.
[Amended 8-8-2023 by Ord. No. 2023-02]
(1)
The height of a structure shall be determined in accordance with §
500-832.
(2)
The maximum height of a residence is 35 feet, excluding mechanical
penthouses the height of which are determined with reference to the
International Building Code. Accessory buildings may be 25 feet in
height. Any nonresidential building height in excess of 35 feet requires
conditional use approval by the Board of Supervisors. In considering
an application for conditional use related to building height, the
Board of Supervisors shall consider the following factors:
(a)
The nature of the building itself and the extent to which it
is consistent or inconsistent with the landscape and structures in
the vicinity of it;
(b)
The height of other buildings in the area;
(c)
The proximity of residences and the extent to which the height
of the building diminishes the quality of life for those residing
in proximity to the building, also considering topography and the
extent to which the building is visible from nearby residences;
(d)
Whether the building will include a mechanical penthouse that
is excluded from the definition of building height;
(e)
The extent to which the requirements, standards or common practices
associated with a particular proposed use require a building that
is more than 35 feet tall;
(f)
Whether the increased building height will increase the impact
of the use of the building with respect to noise, traffic volume,
light spillover, or similar community impacts.
I. Permitted uses.
(1)
All uses permitted by §
500-1201, except:
(b)
Accessory uses in conformance with this chapter,
with the following limitations:
[1]
Private garages shall be permitted, subject to §
500-808B(2). R-2 and R-3 District gross area requirements shall apply to development under this section.
[2]
One storage shed shall be permitted for garden
equipment, household goods, and/or sporting goods owned and used by
the residents of the dwelling, with a total floor area of 150 square
feet or less.
J. Design criteria.
(1)
Lots shall be laid out and designed, to the
greatest extent feasible, to preserve and protect historic and archaeological
sites, farmland, stream corridors, forested areas and large trees,
scenic views (particularly as seen from public roads), ridgelines
and hilltops.
(2)
The design of the development shall minimize
earthmoving and follow the natural topography to the greatest extent
feasible.
(3)
The development shall provide a landscaped buffer or screen along the property lines at the periphery of the development to protect the privacy of adjacent residents, consistent with §
500-2705, Landscaped buffers and screens, of this chapter.
(4)
To the extent feasible, all buildings shall
be located out of view from any Township road, and protected open
space shall be located adjacent to public ways.
(5)
Residential dwelling units located within the development shall not be located along existing roads within the Township and/or along any proposed interior collector street. Building lots that front on existing Township roads shall be permitted by conditional use and shall meet all dimensional standards of §
500-1202 and not the dimensional standards of this section. Under no circumstances shall lots front on arterial or collector streets.
K. Open space design criteria. Open space areas shall be located and designed in compliance with the Upper Hanover Township Open Space and Environmental Resource Protection Plan Update (2006), or any successor plan thereto, and with the requirements set forth in Chapter
425, Subdivision and Land Development.
[Amended 12-13-2005 by Ord. No. 2005-13; 2-13-2007 by Ord. No. 2007-01]
L. Management, maintenance and ownership of open space. The management, maintenance and ownership of open space shall be subject to provisions established in written agreements, satisfactory to the Board of Supervisors, upon recommendation of the Township Solicitor. Such private management, maintenance and ownership shall be governed by the requirements set forth in Chapter
425, Subdivision and Land Development.
[Amended 12-13-2005 by Ord. No. 2005-13]
|
Figure 12.1: Permitted Lots Worksheet [Amended 3-9-2004 by Ord. No. 2004-01 ; 9-13-2005 by Ord. No. 2005-10]
|
|
Gross Tract Area
|
(1) _____ acres
|
|
Nondevelopable Area Calculation1
|
|
|
a.
|
Areas in the Floodplain Conservation Overlay District (Article XX)
|
_____ acres
|
|
|
b.
|
Areas in the Riparian Corridor Conservation Overlay District (Article XXIX)
|
_____ acres
|
|
|
c.
|
Areas identified on the Steep Slope Map in the Steep Slope Conservation Overlay District (Article XXV)
|
|
|
|
|
Slopes 25% or greater
|
_____ acres
|
|
|
|
Slopes greater than or equal to 15% less than
25% (acres ÷ 2)
|
_____ acres
|
|
|
d.
|
Wetlands
|
_____ acres
|
|
|
e.
|
Legal rights-of-way of existing streets
|
_____ acres
|
|
|
f.
|
Utility easements and rights-of-way
|
_____ acres
|
|
|
g.
|
Areas used for other purposes
|
_____ acres
|
|
|
h.
|
Areas legally restricted from development
|
_____ acres
|
|
Total nondevelopable area: (Add Lines a-h)
|
(2) _____ acres
|
|
Developable Area: Line (1) - Line (2)
|
(3) _____ acres
|
|
Lots Permitted (maximum): Divide Line (3) by
1.837 acres/lot
|
(4) _____ lots
|
|
Density Bonus Multiplier:
|
|
For open space percentage of 50%, multiplier
is 1.00
|
|
For open space percentage of 60%, multiplier
is 1.25 (maximum)
|
|
Calculate intermediate values by adding 0.025
for each % between 50% and 60%
|
(5) _____
|
|
Maximum Number of Lots Permitted: Multiply Line
(4) x Line (5)
|
(6) _____ lots
|
|
(If fraction of lot: round up, if greater than
0.5 lot; otherwise, round down.)
|
|
NOTE:
|
---|
|
1
|
Nondevelopable areas shall not be double-counted
(i.e., wetlands and water bodies located entirely within the floodplain).
|
[Added 10-11-2005 by Ord. No. 2005-12]
As a conditional use, a tract of land meeting the requirements of §
500-1204B that is either an existing institutional use or adjacent to an existing institutional use, that was owned by that institution prior to July of 2005, may be developed or redeveloped with those uses listed in §
500-1204G. Where there are differences in permitted uses and dimensional standards between this section and other sections of this chapter, the provisions of this section shall apply.
A. Application.
(1)
Purposes. The primary purpose of these standards is to provide for the development of existing tracts of institutional land and/or the land adjacent to and owned by institutional uses. As a conditional use, it allows for the development or redevelopment of the tract into single-family detached houses, age-qualified detached or attached single-family houses, or other uses as listed in §
500-1204G in accordance with the conditional use procedures in §
500-818. In recognition that the institutional use would likely be more intensive than the underlying R-1 Agricultural-Low Density Residential District, a higher density is permitted for the area.
B. Qualifying tract.
(1)
Minimum tract size: 50 acres gross. The tract
shall include only that land which will be developed as permitted
by this section. Any additional present or previous holdings of the
institutional entity shall not be included in the tract size.
(2)
Public sewer and water shall be provided.
(3)
A minimum of 50% of the gross area of the development
shall be set aside as common open space.
[Amended 12-13-2005 by Ord. No. 2005-13]
C. Dimensional standards.
(1)
The overall gross residential density of the
tract shall not exceed 1.25 dwelling units per developable acre.
(2)
In the case of an age-qualified community, overall
gross residential density shall not exceed 2.3 dwelling units per
developable acre. For the purposes of computing density in a retirement
complex, two beds in skilled care facilities or personal care congregate
facilities shall be considered the equivalent of one dwelling unit.
(3)
The area that is not used for development shall
be set aside as common open space.
(4)
Minimum lot area, lot width and yards for single-family non-age-qualified detached houses shall be in accordance with §
500-1203D.
(5)
Minimum lot area, lot width and yards for single-family detached and attached age-qualified houses shall be in accordance with §
500-1304D(1) and
(2), respectively.
(6)
Additional setbacks for all single-family development pursuant to this section shall be in accordance with §
500-1203E.
(7)
No more than 50% of the units in a retirement complex are permitted to be any combination of skilled care facilities or personal care congregate facilities. Additional development regulations for a retirement complex shall be in accordance with §
500-837B and
C.
[Amended 6-10-2008 by Ord. No. 2008-04]
D. Accessory uses shall be in accordance with §
500-808B.
E. Minimum setbacks for buildings and structures (except private garages) that are accessory to a residential use shall be in accordance with §
500-1203G.
F. Maximum permitted height for buildings and structures:
(1)
Residential buildings: 35 feet.
(2)
Buildings and structures accessory to a residential
use: 25 feet.
G. Permitted uses.
(1)
Single-family detached dwelling.
(2)
Age-qualified single-family detached dwelling.
(3)
Age-qualified single-family attached dwelling.
(4)
Retirement complex as provided for in §
500-837.
[Amended 6-10-2008 by Ord. No. 2008-04]
(5)
Open space and outdoor recreational uses, in compliance with Article
XXVII, Open Space and Outdoor Recreation Regulations, of this chapter.
(6)
Accessory uses to a residential use in conformance
with this chapter, with the following limitations:
(a)
Private garages shall be permitted, subject to §
500-808B(2)(a). R-2 and R-3 District gross area requirements shall apply to development under this section.
(b)
One storage shed shall be permitted for garden
equipment, household goods, and/or sporting goods owned and used by
the residents of the dwelling, with a total floor area of 150 square
feet or less.
H. Design criteria shall be in accordance with §
500-1203J.
I. Open space design criteria shall be in accordance with §
500-1203K.
J. For age-qualified units, the requirements of §
500-1304E shall be applicable, except where they conflict with this section.