A. 
General design guidelines.
(1) 
Stormwater shall not be transferred from one watershed to another, unless:
(a) 
The watersheds are subwatersheds of a common watershed which join together within the perimeter of the property;
(b) 
The effect of the transfer does not alter the peak rate discharge onto adjacent lands; or
(c) 
Easements from the affected landowner(s) are provided.
(2) 
Consideration shall be given to the relationship of the subject property to the drainage pattern of the watershed. A concentrated discharge of stormwater to an adjacent property shall be within an existing watercourse or confined in an easement or returned to a predevelopment-flow-type condition.
(3) 
Low-impact development BMPs and recharge facilities are encouraged (e.g., rooftop storage, drywells, cisterns, recreation area ponding, diversion structures, porous pavements, holding tanks, infiltration systems, in-line storage in storm sewers, and grading patterns). They shall be located, designed, and constructed in accordance with the latest technical guidance published by PADEP, provided they are accompanied by detailed engineering plans and performance capabilities and supporting site-specific soils, geology, runoff and groundwater and infiltration rate data to verify proposed designs. Additional guidance from other sources may be accepted at the discretion of the Municipal Engineer (a preapplication meeting is suggested).
(4) 
All existing and natural watercourses, channels, drainage systems and areas of surface water concentration shall be maintained in their existing condition unless an alteration is approved by the appropriate regulatory agency.
(5) 
The design of all stormwater management facilities shall incorporate sound engineering principles and practices. Mahoning Township shall reserve the right to disapprove any design that would result in the continuation or exacerbation of a documented adverse hydrologic or hydraulic condition within the watershed, as identified in the plan.
(6) 
The design and construction of multiple-use stormwater detention facilities are strongly encouraged. In addition to stormwater management, facilities should, where appropriate, allow for recreational uses including ball fields, play areas, picnic grounds, etc. Consultation with Mahoning Township and prior approval are required before design. Provision for permanent wet ponds with stormwater management capabilities may also be appropriate.
(a) 
Multiple-use basins should be constructed so that potentially dangerous conditions are not created.
(b) 
Water quality basins or recharge basins that are designed for a slow release of water or other extended detention ponds are not permitted for recreational uses, unless the ponded areas are clearly separated and secure.
(7) 
Should any stormwater management facility require a dam safety permit under PADEP Chapter 105, the facility shall be designed in accordance with Chapter 105 and meet the regulations of Chapter 105 concerning dam safety.
B. 
Stormwater management facility design considerations. All stormwater management facilities shall meet the following design requirements:
(1) 
For stormwater management facilities and BMPs that retain or detain water and are of a relatively small scale (less than or equal to three feet of depth from the bottom of the basin to the top of embankment and less than one acre-foot of storage), exceptions to the requirements in this section may be allowed at the sole discretion of Mahoning Township.
(2) 
No outlet structure from a stormwater management facility, or swale, shall discharge directly onto a municipal or state roadway.
(3) 
The top, or toe, of any slope shall be located a minimum of 10 feet from any property line.
(4) 
The minimum horizontal distance between any structure and any stormwater facility shall be 25 feet. The lowest floor elevation of any structure constructed immediately adjacent to a detention basin or other stormwater facility shall be a minimum of two feet above the one-hundred-year water surface elevation.
(5) 
Stormwater management facility bottom (or surface of permanent pool) elevations must be greater than adjacent floodplain elevations (FEMA or HEC-RAS analysis). If no floodplain is defined, bottom elevations must be greater than existing ground elevations 50 feet horizontally from top of stream bank in the facilities' vicinity.
(6) 
Basin outflow culverts discharging into floodplains must account for tailwater. Tailwater corresponding to the one-hundred-year floodplain elevation must be used for all twenty-four-hour design storms, or the applicant may elect to determine flood elevations of the adjacent watercourse for each twenty-four-hour design storm. The floodplain is assumed to be 50 feet from top of stream bank in areas where a floodplain is not designated, or no other evidence is provided.
(7) 
The invert of all stormwater management facilities and underground infiltration/storage facilities shall be located a minimum of two feet above the seasonal high groundwater table. The invert of stormwater facilities may be lowered if adequate subsurface drainage is provided.
(8) 
Whenever possible the side slopes and basin shape shall be amenable to the natural topography. Vertical side slopes and rectangular basins shall be avoided whenever possible.
(9) 
Exterior slopes of compacted soil shall not exceed 3:1, and may be further reduced if the soil has unstable characteristics.
(10) 
Interior slopes of the basin shall not exceed 3:1.
(11) 
Unless specifically designed as a volume control facility, all stormwater management facilities shall have a minimum slope of 1% extending radially out from the principal outlet structure. Facilities designed as water quality/infiltration BMPs may have a bottom slope of zero.
(12) 
Impervious low-flow channels are not permitted within stormwater management facilities.
(13) 
Unless specifically designed as a volume control or water quality facility, all stormwater management facilities must empty over a period of time not less than 24 hours and not more than 72 hours from the end of the facility's inflow hydrograph. Infiltration tests performed at the facility locations and proposed basin bottom depths, in accordance with the BMP Manual, must support time-to-empty calculations if infiltration is a factor.
(14) 
Energy dissipators and/or level spreaders shall be installed at points where pipes or drainageways discharge to or from basins. Discharges to drainage swales shall be dissipated, or piped, to an acceptable point.
(15) 
Landscaping and planting specifications must be provided for all stormwater management basins and be specific for each type of basin.
(a) 
Minimal-maintenance, saturation-tolerant vegetation must be provided in facilities designed as water quality/infiltration BMPs.
(16) 
A safety fence may be required, at the discretion of Mahoning Township, for any stormwater management facility. The fence shall be a minimum of four feet high, and of a material acceptable to Mahoning Township. A gate with a minimum opening of 10 feet shall be provided for maintenance access.
(17) 
Principal outlet structures. All principal outlet structures shall:
(a) 
Be constructed of reinforced concrete or an alternative material approved by the Municipal Engineer. When approved for use, all metal risers shall:
[1] 
Be suitably coated to prevent corrosion.
[2] 
Have a concrete base attached with a watertight connection. The base shall be sufficient weight to prevent flotation of the riser.
[3] 
Provide a trash rack or similar appurtenance to prevent debris from entering the riser.
[4] 
Provide an antivortex device, consisting of a thin vertical plate normal to the basin berm.
(b) 
Provide trash racks to prevent clogging of primary outflow structure stages for all orifices equivalent to 12 inches or smaller in diameter.
(c) 
Provide outlet aprons which shall, at a minimum, extend to the toe of the basin slope.
(d) 
Where spillways will be used to control peak discharges in excess of the ten-year storm, the control weirs shall be constructed to withstand the pressures of impounded waters and convey flows at computed outlet velocities without erosion.
(18) 
Emergency spillways. Any stormwater management facility designed to store runoff shall provide an emergency spillway designed to convey the one-hundred-year postdevelopment peak rate flow with a blocked primary outlet structure. The emergency spillway shall be designed per the following requirements:
(a) 
The top of embankment elevation shall provide a minimum one foot of freeboard above the maximum water surface elevation. This is to be calculated when the spillway functions for the one-hundred-year postdevelopment inflow, with a blocked outlet structure.
(b) 
Avoid locating on fill areas, whenever possible.
(c) 
The spillway shall be armored to prevent erosion during the one-hundred-year postdevelopment flow, with a blocked primary outlet structure.
[1] 
Synthetic liners or riprap may be used, and calculations sufficient to support proposed armor must be provided. An earthen plug must be used to accurately control the spillway invert if riprap is the proposed armoring material. Emergency spillway armor must extend up the sides of the spillway, and continue at full width to a minimum of 10 feet past the toe of slope.
(d) 
The Municipal Engineer may require the use of additional protection when slopes exceed 4:1 and spillway velocities might exceed NRCS standards for the particular soils involved.
(e) 
Any underground stormwater management facility (pipe storage systems) must have a method to bypass flows higher than the required design (up to a one-hundred-year postdevelopment inflow) without structural failure, or causing downstream harm or safety risks.
(19) 
Stormwater management basins. Design of stormwater management facilities having three feet or more of water depth (measured vertically from the lowest elevation in the facility to the crest of the emergency spillway) shall meet the following additional requirements:
(a) 
The maximum water depth within any stormwater management facility shall be no greater than eight feet when functioning through the primary outlet structure.
(b) 
The top of embankment width shall be at least 10 feet.
(c) 
A ten-foot-wide access to the basin bottom must be provided with a maximum longitudinal slope of 10%.
(d) 
Berms shall be constructed using soils that conform to the unified soil classification of CH, MH, CL or ML. The embankments shall be constructed in a maximum of six-inch lifts. The lifts will each be compacted to a density of 98% of a standard proctor analysis as per each layer of compacted fill shall be tested to determine its density analysis per ASTM 698. Each layer of compacted fill shall be tested to determine its density per ASTM 2922 or ASTM 3017.
(e) 
A cutoff and key trench of impervious material shall be provided under all embankments four feet or greater in height. The cutoff trench shall run the entire length of the embankment and tie into undisturbed natural ground.
(f) 
Antiseep collars, or a PADEP-approved alternative, must be provided on all outflow culverts in accordance with the methodology contained in the latest edition of the PADEP E&S Manual. An increase in seepage length of 15% must be used in accordance with the requirements for permanent antiseep collars.
(20) 
Construction of stormwater management facilities.
(a) 
Basins used for rate control only shall be installed prior to or concurrent with any earthmoving or land disturbances which they will serve. The phasing of their construction shall be noted in the narrative and on the plan.
(b) 
Basins that include water quality or recharge components shall have those components installed in such a manner as to not disturb or diminish their effectiveness.
(c) 
Compaction test reports shall be kept on file at the site and be subject to review at all times with copies being forwarded to the Municipal Engineer upon request.
(d) 
Temporary and permanent grasses or stabilization measures shall be established on the sides and base of all earthen basins within 15 days of construction.
C. 
Stormwater-carrying facilities.
(1) 
All storm sewer pipes, grass waterways, open channels, swales and other stormwater-carrying facilities that service drainage areas within the site must be able to convey postdevelopment runoff from the ten-year design storm.
(2) 
Stormwater management facilities that convey off-site water through the site shall be designed to convey the twenty-five-year storm event (or larger events, as determined by the Municipal Engineer).
(3) 
All developments shall include provisions that allow for the overland conveyance and flow of the postdevelopment one-hundred-year storm event without damage to public or private property.
(4) 
Storm sewers.
(a) 
New storm sewers shall be designed to convey postdevelopment runoff without surcharging inlets for the ten-year storm event.
(b) 
When proposing to connect to an existing storm sewer system, the applicant must demonstrate that the proposed system will not exacerbate any existing stormwater problems and will not exceed downstream capacity.
(c) 
Inlets, manholes, pipes, and culverts shall be designed in accordance with PennDOT Publication 13M, and constructed in accordance PennDOT Publication 40, and PennDOT Publication 72M — Standards for Roadway Construction (RC). Other construction details may be approved at the sole discretion of Mahoning Township. All material and construction details (inlets, manholes, pipe trenches, etc.), must be shown on the SWM site plan. A note should be added to the construction plans stating that all inlet and junction box frames, concrete top units, and grade adjustment rings shall be set in a bed of mortar.
(d) 
A minimum pipe size of 18 inches in diameter shall be used in all roadway systems (public or private) proposed for construction in Mahoning Township. Pipes should be designed to provide a minimum velocity of 2 1/2 feet per second when flowing full. Arch pipes of equivalent cross-sectional area may be substituted in lieu of circular pipe where the depth of cover is shallow or where conflicts with utilities exist.
(e) 
All storm sewer pipes shall be laid to a minimum depth of one foot from the bottom of foundations or pavement to the crown of pipe.
(f) 
In curbed roadway sections, the maximum encroachment of water on the roadway travel lanes should not exceed 1/2 of a lane or one inch less than the depth of curb during the roadway design storm of five minutes' duration. Gutter depth shall be verified by inlet capture/capacity calculations that account for road slope and opening area. Design of roadway drainage should be consistent with the guidance in PennDOT Publication 13M.
[1] 
Inlets should be placed at a maximum of 600 feet apart.
[2] 
Inlets should be placed so drainage cannot cross intersections or street center lines.
(g) 
Standard Type "C" inlets with eight-inch hoods should be used along curbed roadway networks. Type "C" inlets with ten-inch hoods that provide a two-inch sump condition may be used with approval of Mahoning Township when roadway longitudinal slopes are 1.0% or less.
(h) 
For inlets containing a change in pipe size, the elevation of the crown of the smaller pipes should be higher than the crown of the largest pipe.
(i) 
All inlets should provide a minimum two-inch drop between the lowest inlet pipe invert elevation and the outlet pipe invert elevation.
(j) 
On curbed sections, a double inlet should be placed at the low point of sag vertical curves, or a flanking inlet should be placed within 100 feet on each side of the inlet at the low point.
(k) 
At all roadway low points, swales and easements should be provided behind the curb or swale and through adjacent properties to channelize and direct any overflow of stormwater runoff away from dwellings and structures.
(l) 
All inlets in paved areas shall have heavy-duty bicycle-safe grating. A note to this effect shall be added to the SWM site plan and inlet details therein.
(m) 
Inlets must be sized to accept the specified pipe sizes without knocking out any of the inlet corners. All pipes entering or exiting inlets shall be cut flush with the inside wall of the inlet. A note to this effect shall be added to the SWM site plan and inlet details therein.
(n) 
Inlets should have weep holes covered with geotextile fabric placed at appropriate elevations to completely drain the subgrade prior to placing the base and surface course on roadways.
(o) 
Inlets, junction boxes, or access holes greater than five feet in depth should be equipped with ladder rungs placed 15 inches on center and shall be detailed on the SWM site plan.
(p) 
Inlets should not have a sump condition in the bottom (unless designed as a water quality BMP). Pipes shall be flush with the bottom inside surface of the box or concrete channels should be poured.
(q) 
Accessible drainage structures should be located on a continuous storm sewer system at all invert changes, at all locations where a transition in storm sewer pipe sizing is required, at all vertical and horizontal angle points exceeding 5°, and at all points of convergence of two or more storm sewer pipes.
(r) 
All storm drainage piping should be provided with either reinforced concrete headwalls at inlets or end sections at outlets compatible with the pipe material and size.
(s) 
Outlet protection and energy dissipaters shall be provided at all surface discharge points in order to minimize erosion consistent with PennDOT Publication 13M, or FHWA Publication HEC-14.
[1] 
Flow velocities and volumes from any storm sewer shall not cause a degradation of the receiving water body.
(t) 
Stormwater roof drains and pipes should not be directly connected to storm sewers or discharge onto impervious areas without prior approval by Mahoning Township.
(5) 
Swale conveyance facilities.
(a) 
Swales must be able to convey postdevelopment runoff from a ten-year design storm with six inches of freeboard to top of the swale.
(b) 
Swales shall have side slopes no steeper than 3:1 unless approved by Mahoning Township.
(c) 
All swales shall be designed, labeled on the SWM site plan, and details provided to adequately construct and maintain the design dimension of the swales.
(d) 
Swales shall be designed for stability using velocity or shear criteria. Velocity criteria may be used for channels with less than 10% slope. Shear criteria may be used for all swales. Documentation must be provided to support velocity and/or shear limitations used in calculations.
(e) 
Where swale bends occur, the computed velocities or shear stresses shall be multiplied by the following factor for the purpose of designing swale erosion protection:
[1] 
When swale bend is 30° to 60°: 1.75.
[2] 
When swale bend is 60° to 90°: 2.00.
[3] 
When swale bend is 90° or greater: 2.50.
(f) 
Manning's "n" values used for swale capacity design must reflect the permanent condition.
A. 
All calculations shall be consistent with the guidelines set forth in the BMP Manual, as amended herein.
B. 
Stormwater runoff from all development sites shall be calculated using either the Rational Method or the NRCS Rainfall-Runoff Methodology. Methods shall be selected by the design professional based on the individual limitations and suitability of each method for a particular site.
C. 
Rainfall values.
(1) 
Rational Method: The Pennsylvania Department of Transportation Drainage Manual, Intensity-Duration-Frequency Curves, Publication 584, Chapter 7A, latest edition, shall be used in conjunction with the appropriate time of concentration and return period.
(2) 
NRCS Rainfall-Runoff Method: The Soil Conservation Service Type II, twenty-four-hour rainfall distribution shall be used in conjunction with rainfall depths from NOAA Atlas 14 or be consistent with the following table:
Return Interval
(Year)
24-hour Rainfall Total
(Inches)
1
2.35
2
2.82
10
4.09
25
5.05
50
5.94
100
6.99
D. 
Runoff volume.
(1) 
Rational Method: not to be used to calculate runoff volume.
(2) 
NRCS Rainfall-Runoff Method: This method shall be used to estimate the change in volume due to regulated activities. Combining curve numbers for land areas proposed for development with curve numbers for areas unaffected by the proposed development into a single weighted curve number is not acceptable.
E. 
Peak flow rates.
(1) 
Rational Method: This method may be used for design of conveyance facilities only. Extreme caution should be used by the design professional if the watershed has more than one main drainage channel, if the watershed is divided so that hydrologic properties are significantly different in one versus the other, if the time of concentration exceeds 60 minutes, or if stormwater runoff volume is an important factor. The combination of Rational Method hydrographs based on timing shall be prohibited.
(2) 
NRCS Rainfall-Runoff Method:
(a) 
This method is recommended for design of stormwater management facilities and where stormwater runoff volume must be taken into consideration. The following provides guidance on the model applicability:
[1] 
NRCS's TR-55: limited to 100 acres in size.
[2] 
NRCS's TR-20 or HEC-HMS: no size limitations.
[3] 
Other models as preapproved by the Municipal Engineer.
(b) 
The NRCS antecedent runoff condition II (ARC II, previously AMC II) must be used for all simulations. The use of continuous simulation models that vary the ARC are not permitted for stormwater management purposes.
(3) 
For comparison of peak flow rates, flows shall be rounded to a tenth of a cubic foot per second (cfs).
F. 
Runoff coefficients.
(1) 
Rational Method: use Table C-1 (Appendix C[1]).
[1]
Editor's Note: Said Appendix is included at the end of this chapter.
(2) 
NRCS Rainfall-Runoff Method: use Table C-2 (Appendix C). Curve numbers (CN) should be rounded to tenths for use in hydrologic models as they are a design tool with statistical variability. For large sites, CN's should realistically be rounded to the nearest whole number.
(3) 
For the purposes of predevelopment peak flow rate and volume determination, existing nonforested pervious area conditions shall be considered as meadow (good condition).
(4) 
For the purposes of predevelopment peak flow rate and volume determination, 20% of existing impervious area, when present, shall be considered meadow (good condition).
G. 
Design storm.
(1) 
All stormwater management facilities shall be verified by routing the proposed one-year, two-year, ten-year, twenty-five-year, fifty-year, and one-hundred-year hydrographs through the facility using the storage indication method or modified puls method. The twenty-four-hour design storm hydrograph shall be computed using a calculation method that produces a full hydrograph.
(2) 
The stormwater management and drainage system shall be designed to safely convey the postdevelopment one-hundred-year storm event to stormwater detention facilities, for the purpose of meeting peak rate control.
(3) 
All structures (culvert or bridges) proposed to convey runoff under a municipal roadway shall be designed to pass the fifty-year design storm with a minimum of one foot of freeboard measured below the lowest point along the inside surface of the crown for culverts or the low chord for bridges. For detailed guidance for design of culverts and bridges, refer to PennDOT Publications 13M and 15M.
H. 
Time of concentration.
(1) 
The time of concentration is a parameter that represents the average condition that best reflects the hydrologic response of the area. The following time of concentration (Tc) computational methodologies shall be used unless another method is preapproved by the Municipal Engineer:
(a) 
Predevelopment: NRCS's Lag Equation.
Time of Concentration = Tc = [(Tlag/.6) * 60] (minutes)
Where:
Tlag
=
Lag time (hours)
L
=
Hydraulic length of watershed (feet)
Y
=
Average overland slope of watershed (percent)
S
=
Maximum retention in watershed as defined by: S = [(1,000/CN) — 10]
CN
=
NRCS curve number for watershed
(b) 
Postdevelopment; commercial, industrial, or other areas with large impervious areas (>20% impervious area): NRCS Segmental Method. The length of sheet flow shall be limited to 100 feet. Tc for channel and pipe flow shall be computed using Manning's equation.
(c) 
Postdevelopment; residential, cluster, or other low-impact designs less than or equal to 20% impervious area: NRCS Lag Equation or NRCS Segmental Method.
(2) 
Additionally, the following provisions shall apply to calculations for time of concentration:
(a) 
The postdevelopment Tc shall never be greater than the predevelopment Tc for any watershed or subwatershed. This includes when the designer has specifically used swales to reduce flow velocities. In the event that the designer believes that the postdevelopment Tc is greater, it shall still be set equal to the predevelopment Tc for modeling purposes.
(b) 
The minimum Tc for any watershed shall be five minutes.
(c) 
The designer may choose to assume a five-minute Tc for any postdevelopment watershed or subwatershed without providing any computations.
(d) 
The designer must provide computations for all predevelopment Tc paths. A five-minute Tc cannot be assumed for predevelopment.
(e) 
Undetained fringe areas (areas that are not tributary to a stormwater facility but where a reasonable effort has been made to convey runoff from all new impervious coverage to best management practices) may be assumed to represent the predevelopment conditions for purpose of Tc calculation.
I. 
Drainage areas tributary to sinkholes or closed depressions in areas underlain by limestone or carbonate geologic features shall be excluded from the modeled point of analysis defining predevelopment flows. If left undisturbed during construction activities, areas draining to closed depressions may also be used to reduce peak runoff rates in the postdevelopment analysis. New, additional contributing runoff should not be directed to existing sinkholes or closed depressions.
J. 
Where uniform flow is anticipated, Manning's equation shall be used for hydraulic computations and to determine the capacity of open channels, pipes, and storm sewers. Manning's equation should not be used for analysis of pipes under pressure flow or for analysis of culverts. Manning's "n" values shall be obtained from PennDOT's Drainage Manual, Publication 584 or PennDOT Publication 13M. Inlet control shall be checked at all inlet boxes to ensure the headwater depth during the ten-year design event is contained below the top of grate for each inlet box.
K. 
Mahoning Township may approve the use of any generally accepted full hydrograph approximation technique that shall use a total runoff volume that is consistent with the volume from a method that produces a full hydrograph.
L. 
Mahoning Township has the authority to require that computed existing runoff rates be reconciled with field observations, conditions and site history. If the designer can substantiate, through actual physical calibration, that more appropriate runoff and time of concentration values should be utilized at a particular site, then appropriate variations may be made upon review and recommendation of Mahoning Township.
Any downstream or off-site hydraulic capacity analysis conducted in accordance with this chapter shall use the following criteria for determining adequacy:
A. 
Natural or man-made channels or swales must be able to convey the postdevelopment runoff associated with a bankfull event (or two-year storm event) at velocities consistent with protection of the channels from erosion. Acceptable velocities shall be based upon criteria included in the PADEP Erosion and Sediment Pollution Control Program Manual.
B. 
Natural or man-made channels or swales must be able to convey the postdevelopment twenty-five-year design storm runoff without creating any hazard to persons or property.
C. 
Culverts, bridges, storm sewers or any other facilities which must pass or convey flows from the tributary area must be designed in accordance with PADEP, Chapter 105, regulations (if applicable) and, at a minimum, pass the postdevelopment twenty-five-year design storm runoff.
D. 
It must be demonstrated that the downstream conveyance channel, other stormwater facilities, roadways, or overland areas are capable of safely conveying the one-hundred-year design storm without causing additional damage to buildings or other infrastructure.
E. 
Proposed projects must be consistent with regulations from the National Flood Insurance Program and all ordinances and sections of the Mahoning Township Code adopted in conformance therewith.