[Ord. No. 1251 §1(701), 10-15-2002]
Applications and materials submitted under the provisions of
this Chapter shall conform to the specifications contained in this
Article. The preliminary plat and final plat shall be prepared by
qualified personnel in accordance with the requirements of this Article.
[Ord. No. 1251 §1(702), 10-15-2002]
A. A development
site plan is to be submitted for all developments except for the following,
unless otherwise required by other provisions of this Chapter:
1. Construction of or additions to a single-family detached dwelling
or duplex dwelling on a lot of record.
2. Construction of or addition to any permitted accessory use to a single-family
detached dwelling or duplex dwelling on a lot of record.
3. Any temporary use permitted by this Chapter.
4. Remodeling of a building or structure if no enlargement or expansion
is involved.
B. The
development site plan shall be drawn to an approximate scale (one
(1) inch equals one hundred (100) feet). Eight (8) copies of the plan
shall be submitted.
C. The
materials submitted should provide sufficient information to determine
whether the proposed development is in compliance with these regulations.
The site plan shall contain the following information:
1. Name and address of the developer.
2. Tract boundary and principal features within one thousand (1,000)
feet.
3. Approximate north point and scale.
4. Total acreage of the proposed development.
5. Existing streets on and adjacent to the tract, including rights-of-way
widths.
6. The location of any proposed streets.
7. Location of any existing or proposed public sewer and water lines.
8. Existing drainage ways and any proposed modifications to drainage
ways.
10. Unique topographical and physical features.
11. Location of proposed buildings, parking or other improvements.
[Ord. No. 1251 §1(703), 10-15-2002]
A. A sketch
plan shall be submitted for all minor or major subdivisions. The sketch
plan is intended to be conceptual in nature and, while accuracy and
legibility are essential, the submission of detailed plans at the
sketch plan stage is discouraged. The material submitted should provide
sufficient information to determine general compliance with these
regulations.
B. The
sketch plan shall be drawn to an approximate scale (one (1) inch equals
one hundred (100) feet). Eight (8) copies of the sketch plan shall
be submitted.
C. The
sketch plan shall show:
1. Name and address of the subdivider and owner.
2. General dimensions and configuration of the tract, including property
line, cemeteries and other principal features on the tract and on
immediately adjacent property.
3. Proposed subdivision name and location by lot, section, township,
range or other appropriate description. A metes and bounds description
is not required.
4. Approximate north point, scale, and date of preparation.
5. The approximate total acreage of the proposed subdivision.
6. The classification, location, dimensions and name of all existing
or recorded streets on and immediately adjacent to the tract, including
the width of rights-of-way.
7. The tentative location, width and classification of all proposed
streets.
8. The approximate location and nature of all utility rights-of-way,
easements, facilities and structures on or immediately adjacent to
the tract.
9. The approximate location and size of culverts, storm sewers, impoundments
or other storm water management facilities on or immediately adjacent
to the tract.
10. The approximate location, dimensions and configuration of all proposed
or existing lots.
11. Unique topographical and physical features. Contour intervals may
be based on U.S.G.S data at the ten (10) foot interval level.
12. The approximate location and general layout of proposed water, sewer
and storm water management systems designed to serve the subdivision.
[Ord. No. 1251 §1(704), 10-15-2002]
A. The
preliminary plat application shall be accompanied by ten (10) black
line or blue line print paper copies of the preliminary plat. The
preliminary plat sheet size shall be twenty-four (24) inches by thirty-six
(36) inches. The plat shall be drawn at a scale no greater than one
hundred (100) feet to the inch and which is in increments of ten (10)
feet.
B. The
preliminary plat shall show the following information:
1. The name of the subdivision, which name shall not duplicate the name
of any existing subdivision as recorded in the Stone County Registry.
2. The name(s) and address(es) of the subdivision owner or owners.
3. Date of preliminary plat submittal.
4. Property description of the subdivision.
5. Approximate north arrow and the scale in which the plat is drawn.
6. A listing of the following information:
a. Total acreage of the subdivision;
c. Current zoning of the tract;
e. Smallest lot with lot number and area; and
f. Largest lot with lot number and area.
7. Vicinity map showing the location of the proposed subdivision and
all streets, roads, and municipal boundaries existing within one thousand
(1,000) feet of any part of the property to be subdivided.
8. Contours at vertical intervals of ten (10) feet. Datum shall be referenced
to the appropriate U.S.G.S. Topographic Maps.
9. Approximate tract boundaries.
10. The names and locations of immediately adjoining subdivisions and
the names of immediately adjoining property owners.
11. The general location and approximate dimensions of any existing street
right-of-way intersecting or paralleling the boundaries of the tract,
as well as the distance from the centerline of adjacent streets to
the tract boundaries.
12. The general location and approximate dimensions of any easements
existing within or adjacent to the tract boundaries.
13. The location and dimension of all existing streets, roads, railroads,
public sewers, aqueducts, water mains and feeder lines, gas, electric
and oil transmission lines, watercourses, detention areas, drainage
easements, and other significant features within five hundred (500)
feet of any part of the property to be subdivided.
14. The approximate location and extent of all existing structures and
tree masses within the tract.
15. The full plan of development detailing the following information
on a single sheet:
a. The location of all proposed and existing streets, roads, easements,
parks, playgrounds and other public areas and facilities, sewer and
water facilities and storm sewers or other drainage facilities.
b. Lot lines and the approximate dimensions of all lots and lot numbers
in consecutive order.
c. All street and other areas designated for pertinent facilities, public
use or proposed to be dedicated or reserved for future public use,
including the conditions of such dedications.
d. Where applicable, the location of all State or Federal fly zones.
16. A draft of any proposed private restrictions, including boundaries
of each type of restriction. Where applicable, a draft of restrictive
covenants governing the use and maintenance of all common areas, improvements
and facilities.
17. All storm sewers or other drainage facilities with the size and material
of each indicated and any proposed connection to existing facilities.
18. The location, size and material of any capped sewers, house connections,
mains, and laterals, and proposed connection with existing facilities.
19. Records of a title search, indicating any existing covenants on the
land to be subdivided. This may be provided as a separate statement.
[Ord. No. 1251 §1(705), 10-15-2002]
A. The
final plat sheet size shall be twenty-four (24) inches by thirty-six
(36) inches. When more that one (1) sheet is used for any plat, each
sheet shall be numbered consecutively and shall contain a notation
giving the total number of sheets. The plat shall be drawn at a scale
of one hundred (100) feet or less to the inch. The applicant shall
submit nine (9) paper copies and one (1) digital copy of the final
plat of the subdivision. The digital copy shall be to standards acceptable
to the City. The requirement for digital copy may be waived by the
City when deemed appropriate.
B. The
final plat shall show the following information:
1. Name of the subdivision, which name shall not duplicate the name
of any existing subdivision as recorded in the Stone County Registry.
If the name of the final plat is different from the approved preliminary
plat, the preliminary plat name shall be noted on the final plat.
2. Name(s) and addresses(s) of the subdivision owner(s).
3. Surveyor's name, registration number and survey date.
4. Location by section, township, range, City, County and State where
the subdivision is located. If a resubdivision of an existing or approved
subdivision, then by lot or block numbers and name of original subdivision.
5. Date of final plat submittal.
6. True north arrow and scale in which the plat is drawn in feet per
inch or scale ratio, and bar graph.
7. All boundary lines with lengths and courses to hundredths of a foot
and bearings to half minutes (to be determined by survey with an error
of not less than 1:5000).
8. The exact location and the width along the property line of all existing
recorded streets intersecting or paralleling the boundaries of the
tract.
9. The true bearings and distances to nearest established street boundaries,
patent or other established survey lines, or other official monuments,
which shall be located or accurately described on the plat. Any patent
or other established survey or corporation lines shall be accurately
monument-marked and located on the plat, including their names.
10. Accurate location and material of all permanent reference monuments,
complying with the latest Missouri Minimum Standards for Property
Boundary Surveys.
11. Dimensions and location of all arcs, radii, internal angles, points
of curvature and tangent bearings.
12. Street and alley lines (their names, bearings, angles of intersection
and widths, including the widths along the line of any obliquely intersecting
street).
13. All lot lines with dimensions in feet and hundredths, and with bearings
and angles to minutes if other than right angles to the street and
alley lines.
14. All easements and rights-of-way, with the limitations of the easement
rights stated on the plat.
15. For any required off-site easements, evidence of signed and recorded
easement and signed verification from the property owner from whom
the off-site easement was obtained that all conditions of installation
of improvements have been met.
16. Lots numbered in consecutive order. Plats with more than one (1)
block shall also be numbered in consecutive order. In the case of
resubdivision of lots in any block, the resubdivided lots shall be
designated by their original number prefixed with the term most accurately
describing such division or they shall be designated numerically,
beginning with the number following the highest lot numbered in the
block.
18. Sight triangles for intersections, building setback lines with dimensions
as fixed by the Zoning Map or major street plan and any other setback
lines established by public authority.
19. Accurate dimensions of existing public land and of all property to
be dedicated or reserved for public use, with the purpose indicated
thereon.
20. Private covenants, if any, including boundaries of each type of restriction.
Where applicable, restrictive covenants are required governing the
use and maintenance of all common areas, improvements and facilities.
21. Names and locations of adjoining subdivisions and owners of unsubdivided
land.
22. Names, locations and dimensions of adjacent street rights-of-way
within any adjoining subdivision.
23. Any changes or conditions required by the Board of Aldermen in the
approval of the preliminary plat.
24. Certificates as provided for in Section
405.410.
25. If applicable, a statement indicating that the land lies within an
approved planned development district or cluster development.
C. The
application for final plat shall also be accompanied by a notarized
statement verifying that taxes on the property are not delinquent.
[Ord. No. 1251 §1(706), 10-15-2002]
A. All
final plats shall contain the following endorsed certificates:
1. Certificate of ownership and dedication.
I hereby certify that I am the owner of the property described
hereon, which property is located within the City of Branson West,
Missouri, that I hereby freely adopt this plan of subdivision and
dedicate to public use all areas shown on this plat as streets, alleys,
walks, parks, open space and easements, except those specifically
denoted as private, and that I will maintain all such areas until
the offer of dedication is accepted by the appropriate public authority.
All property shown on this plat as dedicated for public use shall
be deemed to be dedicated for any other public use authorized by law
when such other use is approved by the Branson West Board of Aldermen
in the public interest.
|
Date
|
Owner
|
2. Acknowledgment.
STATE OF MISSOURI )
|
|
SS
|
|
COUNTY OF STONE )
|
|
On this __ day of __________, 20__, before me personally appeared
_____________, to me known, who duly sworn, did say that they are
the persons described herein, and that the same executed the foregoing
instrument as their free act and deed. In witness whereof, I have
hereunto set my hand and affixed my official seal in my office in
____________, Stone County, Missouri.
|
|
My Commission Expires ________________________
|
3. Certificate of survey and accuracy.
I, ___________, do hereby certify that this plat was prepared
and the monuments and pins set under my personal supervision from
an actual survey of the land herein, in accordance with the Missouri
Minimum Standards for Property Boundary Surveys, and the Subdivision
Regulations of Branson West, Stone County, Missouri.
|
Surveyor Name and Registration No
|
Date
|
4. Certificate of approval — Planning and Zoning Commission.
I hereby certify that this plat has been approved by the Branson
West, Missouri Planning and Zoning Commission on the date below.
|
Date
|
Secretary
|
5. Certificate of approval — Board of Aldermen.
I hereby certify that this plat has been approved by the Branson
West Board of Aldermen, subject to its being recorded in the Stone
County Registry within thirty (30) days of the date below.
|
Date
|
City Clerk
|
(SEAL)
|
|
6. Recorder's certificate.
I, ______________, Recorder of Stone County do hereby certify
that the within instrument of writing was on the _____ day of _____________,
20__ AD at ___o'clock ___ Min ___ M duly files for record and is recorded
in the records in this office in Book ____ at page ____. In testimony
whereof, I have hereunto set my hand and affixed my official seal
at my office in Galena, Missouri, this ____ day of __________, 20__.
|
[Ord. No. 1251 §1(707), 10-15-2002]
A. Four
(4) copies of a report signed and sealed by a registered engineer
shall be submitted with the preliminary plat that shall provide a
study of the following items as pertaining to the proposed subdivision:
1. Storm water drainage. The storm water drainage report
shall be conducted in accordance with and shall include all applicable
information, maps, calculations and other materials as specified in
the Branson West Design Standards for Public Improvements.
2. Sanitary sewer and water. A report on water and
sewer capacity and needs to include all applicable information as
specified in the Branson West Design Standards for Public Improvements.
3. Traffic analysis and street capacity.
a. Description of the types of traffic expected and the effects on existing
roads.
b. Traffic counts for each outlet from the proposed subdivision in vehicles
per day. If available, traffic counts from the Missouri Department
of Transportation may be used.
c. The traffic analysis must extend from the proposed subdivision to
the nearest arterial. Existing traffic counts may be estimated from
a study of the area served by the subject road or by counting vehicles
consistent with good engineering practice.
d. Evaluation of the capacity of the existing and proposed road system.
e. A listing of each proposed street by name and functional classification.
Proposed right-of-way and design specifications must be indicated.
f. If the proposed development is within one thousand (1,000) feet of
a school or park, the traffic analysis shall include evaluation of
need for pedestrian ways through the development.
4. General information.
a. Area of development utilized by road right-of-way.
b. Area of development dedicated to open space.
e. Schematic diagram showing significant natural features such as stands
of trees, sinkholes, wetlands, rock outcroppings, etc.
[Ord. No. 1251 §1(708), 10-15-2002]
A. Upon
approval of the preliminary plat by the Board of Aldermen, the applicant
shall prepare the required construction plans. All plans shall meet
the requirements of the Branson West Design Standards for Public Improvements.
B. Three
(3) copies of each of the following plans shall be submitted for Commission
review prior to or concurrent with the final plat application:
3. Sediment and erosion control plan;
5. Storm water drainage plan; and
6. Improvements plans for any common areas.