The following words and terms, when used in this division, have
the following meanings, unless the context clearly indicates otherwise.
Air gap.
A complete physical separation between the free flowing discharge
end of a potable water supply pipeline and an open or nonpressure-receiving
vessel.
Atmospheric vacuum breaker.
A testable assembly containing an air inlet valve, a check
seat, and an air inlet port. The flow of water into the body causes
the air inlet valve to close the air inlet port. When the flow of
water stops the air inlet valve falls and forms a check against backsiphonage.
At the same time it opens the air inlet port allowing air to enter
and satisfy the vacuum. Also known as an atmospheric vacuum breaker
backsiphonage prevention assembly.
Backflow prevention.
The mechanical prevention of reverse flow, or backsiphonage,
of nonpotable water from an irrigation system into the potable water
source.
Backflow prevention assembly.
Any testable assembly used to prevent backflow into a potable
water system. The type of assembly used is based on the existing or
potential degree of health hazard and backflow condition.
Consulting.
The act of providing advice, guidance, review or recommendations
related to landscape irrigation systems.
Cross-connection.
An actual or potential connection between a potable water
source and an irrigation system that may contain contaminates or pollutants
or any source of water that has been treated to a lesser degree in
the treatment process.
Design.
The act of determining the various elements of a landscape
irrigation system that will include, but not be limited to, elements
such as collecting site specific information, defining the scope of
the project, defining plant watering needs, selecting and laying out
emission devices, locating system components, conducting hydraulics
calculations, identifying any local regulatory requirements, or scheduling
irrigation work at a site. Completion of the various components will
result in an irrigation plan.
Design pressure.
The pressure that is required for an emission device to operate
properly. Design pressure is calculated by adding the operating pressure
necessary at an emission device to the total of all pressure losses
accumulated from an emission device to the water source.
Double check valve.
A testable assembly that is composed of two independently
acting, approved check valves, including tightly closed resilient
seated shutoff valves attached at each end of the assembly and fitted
with properly located resilient seated test cocks. Also known as a
double check valve backflow prevention assembly.
Emission device.
Any device that is contained within an irrigation system
and that is used to apply water. Common emission devices in an irrigation
system include, but are not limited to, spray and rotary sprinkler
heads, and drip irrigation emitters.
Employed.
Engaged or hired to provide consulting services or perform
any activity relating to the sale, design, installation, maintenance,
alteration, repair, or service to irrigation systems. A person is
employed if that person is in an employer-employee relationship as
defined by Internal Revenue Code, 26 United States Code Service, §3212(d)
based on the behavioral control, financial control, and the type of
relationship involved in performing employment related tasks.
Head-to-head spacing.
The spacing of spray or rotary heads equal to the manufacturer’s
published radius of the head.
Health hazard.
A cross-connection or potential cross-connection with an
irrigation system that involves any substance that may, if introduced
into the potable water supply, cause death or illness, spread disease,
or have a high probability of causing such effects. May also be referred
to as a high health hazard.
Hydraulics.
The science of dynamic and static water; the mathematical
computation of determining pressure losses and pressure requirements
of an irrigation system.
Inspector.
A licensed plumbing inspector, water district operator, other
governmental entity, or irrigation inspector who inspects irrigation
systems and performs other enforcement duties for a municipality or
water district as an employee or as a contractor.
Installer.
A person who actually connects an irrigation system to a
private or public raw or potable water supply system or any water
supply, who is licensed according to title 30, Texas Administrative
Code, chapter 30 (relating to occupational licenses and registrations).
Irrigation inspector.
A person who inspects irrigation systems and performs other
enforcement duties for a municipality or water district as an employee
or as a contractor and is required to be licensed under title 30,
Texas Administrative Code, chapter 30 (relating to occupational licenses
and registrations).
Irrigation plan.
A scaled drawing of a landscape irrigation system which lists
required information, the scope of the project, and represents the
changes made in the installation of the irrigation system.
Irrigation services.
Selling, designing, installing, maintaining, altering, repairing,
servicing, permitting, providing consulting services regarding, or
connecting an irrigation system to a water supply.
Irrigation system.
An assembly of component parts that is permanently installed
for the controlled distribution and conservation of water to irrigate
any type of landscape vegetation in any location, and/or to reduce
dust or control erosion. This term does not include a system that
is used on or by an agricultural operation as defined by Texas Agricultural
Code, §251.002.
Irrigation technician.
A person who works under the supervision of a licensed irrigator
to install, maintain, alter, repair, service or supervise installation
of an irrigation system, including the connection of such system in
or to a private or public, raw or potable water supply system or any
water supply, and who is required to be licensed under title 30, Texas
Administrative Code, chapter 30 (relating to occupational licenses
and registrations).
Irrigation zone.
A subdivision of an irrigation system with a matched precipitation
rate based on plant material type (such as turf, shrubs, or trees),
microclimate factors (such as sun/shade ratio), topographic features
(such as slope) and soil conditions (such as sand, loam, clay, or
combination) or for hydrological control.
Irrigator.
A person who sells, designs, offers consultations regarding,
installs, maintains, alters, repairs, services or supervises the installation
of an irrigation system, including the connection of such system to
a private or public, raw or potable water supply system or any water
supply, and who is required to be licensed under title 30, Texas Administrative
Code, chapter 30.
Irrigator-in-charge.
The irrigator responsible for all irrigation work performed
by an exempt business owner, including, but not limited to obtaining
permits, developing design plans, supervising the work of other irrigators
or irrigation technicians, and installing, selling, maintaining, altering,
repairing, or servicing a landscape irrigation system.
Landscape irrigation.
The science of applying the necessary amount of water to
promote or sustain healthy growth of plant material or turf.
License.
An occupational license that is issued by the Texas Commission
on Environmental Quality under title 30, Texas Administrative Code,
chapter 30 to an individual that authorizes the individual to engage
in an activity that is covered by title 30, Texas Administrative Code,
chapter 30.
Mainline.
A pipe within an irrigation system that delivers water from
the water source to the individual zone valves.
Maintenance checklist.
A document made available to the irrigation system’s
owner or owner’s representative that contains information regarding
the operation and maintenance of the irrigation system, including,
but not limited to: checking and repairing the irrigation system,
setting the automatic controller, checking the rain or moisture sensor,
cleaning filters, pruning grass and plants away from irrigation emitters,
using and operating the irrigation system, the precipitation rates
of each irrigation zone within the system, any water conservation
measures currently in effect from the water purveyor, the name of
the water purveyor, a suggested seasonal or monthly watering schedule
based on current evapotranspiration data for the geographic region,
and the minimum water requirements for the plant material in each
zone based on the soil type and plant material where the system is
installed.
Major maintenance, alteration, repair, or service.
Any activity that involves opening to the atmosphere the
irrigation mainline at any point prior to the discharge side of any
irrigation zone control valve. This includes, but is not limited to,
repairing or connecting into a main supply pipe, replacing a zone
control valve, or repairing a zone control valve in a manner that
opens the system to the atmosphere.
Master valve.
A remote control valve located after the backflow prevention
device that controls the flow of water to the irrigation system mainline.
New installation.
An irrigation system installed at a location where one did
not previously exist.
Pass-through contract.
A written contract between a contractor or builder and a
licensed irrigator or exempt business owner to perform part or all
of the irrigation services relating to an irrigation system.
Pressure vacuum breaker.
An assembly containing an independently operating internally
loaded check valve and an independently operating loaded air inlet
valve located on the discharge side of the check valve. Also known
as a pressure vacuum breaker backsiphonage prevention assembly.
Reclaimed water.
Domestic or municipal wastewater which has been treated to
a quality suitable for beneficial use, such as landscape irrigation.
Records of landscape irrigation activities.
The irrigation plans, contracts, warranty information, invoices,
copies of permits, and other documents that relate to the installation,
maintenance, alteration, repair, or service of a landscape irrigation
system.
Reduced pressure principle backflow prevention assembly.
An assembly containing two independently acting approved
check valves together with a hydraulically operating mechanically
independent pressure differential relief valve located between the
two check valves and below the first check valve.
Supervision.
The on-the-job oversight and direction by a licensed irrigator
who is fulfilling his or her professional responsibility to the client
and/or employer in compliance with local or state requirements. Also
a licensed installer working under the direction of a licensed irrigator
or beginning January 1, 2009, an irrigation technician who is working
under the direction of a licensed irrigator to install, maintain,
alter, repair or service an irrigation system.
Water conservation.
The design, installation, service, and operation of an irrigation
system in a manner that prevents the waste of water, promotes the
most efficient use of water, and applies the least amount of water
that is required to maintain healthy individual plant material or
turf, reduce dust, and control erosion.
Zone flow.
A measurement, in gallons per minute or gallons per hour,
of the actual flow of water through a zone valve, calculated by individually
opening each zone valve and obtaining a valid reading after the pressure
has stabilized. For design purposes, the zone flow is the total flow
of all nozzles in the zone at a specific pressure.
Zone valve.
An automatic valve that controls a single zone of a landscape
irrigation system.
(Ordinance 2008-59 adopted 12/9/08)
(a) Any
person who connects an irrigation system to the water supply within
the city or the city’s extraterritorial jurisdiction, commonly
referred to as the ETJ, must hold a valid license, as defined by title
30, Texas Administrative Code, chapter 30 and required by chapter
1903 of the Texas Occupations Code, or as defined by chapter 365,
title 22 of the Texas Administrative Code and required by chapter
1301 of the Texas Occupations Code.
(b) Exemptions.
A property owner is not required to be licensed in accordance
with Texas Occupations Code, title 12, §1903.002(c)(1) if he
or she is performing irrigation work in a building or on a premises
owned or occupied by the person as the person’s home. A home
or property owner who installs an irrigation system must meet the
standards contained in title 30, Texas Administrative Code, chapter
344 regarding spacing, water pressure, spraying water over impervious
materials, rain or moisture shutoff devices or other technology, backflow
prevention and isolation valves. The city may, at any point, adopt
more stringent requirements for a home or property owner who installs
an irrigation system. See Texas Occupations Code §1903.002 for
other exemptions to the licensing requirement.
(Ordinance 2008-59 adopted 12/9/08)
(a) Any
person installing an irrigation system within the territorial limits
or extraterritorial jurisdiction of the city is required to obtain
a permit from the city. Any plan approved for a permit must be in
compliance with the requirements of this article. (Each city should
include provisions regarding the appropriate department and process
for obtaining a permit.)
(b) Exemptions.
(1) An irrigation system that is an on-site sewage disposal system, as
defined by section 355.002, Health and Safety Code; or
(2) An irrigation system used on or by an agricultural operation as defined
by section 251.002, Agriculture Code; or
(3) An irrigation system connected to a groundwater well used by the
property owner for domestic use.
(Ordinance 2008-59 adopted 12/9/08)
(a) Any
irrigation system that is connected to the potable water supply must
be connected through a backflow prevention method approved by the
Texas Commission on Environmental Quality (TCEQ) and in compliance
with the city’s cross-connection control ordinance to the extent
those provisions do not conflict with TCEQ standards. The backflow
prevention device must be approved by the American Society of Sanitary
Engineers; or the Foundation for Cross-Connection Control and Hydraulic
Research, University of Southern California; or the Uniform Plumbing
Code; or any other laboratory that has equivalent capabilities for
both the laboratory and field evaluation of backflow prevention assemblies.
The backflow prevention device must be installed in accordance with
the laboratory approval standards or if the approval does not include
specific installation information, the manufacturer’s current
published recommendations.
(b) If
conditions that present a high health hazard exist, one of the following
methods must be used to prevent backflow:
(1) An air gap may be used if:
(A) There is an unobstructed physical separation; and
(B) The distance from the lowest point of the water supply outlet to
the flood rim of the fixture or assembly into which the outlet discharges
is at least one inch or twice the diameter of the water supply outlet,
whichever is greater.
(2) Reduced pressure principle backflow prevention assemblies may be
used if:
(A) The device is installed at a minimum of 12 inches above ground in
a location that will ensure that the assembly will not be submerged;
and
(B) Drainage is provided for any water that may be discharged through
the assembly relief valve.
(3) Pressure vacuum breakers may be used if:
(A) No back-pressure condition will occur; and
(B) The device is installed at a minimum of 12 inches above any downstream
piping and the highest downstream opening. Pop-up sprinklers are measured
from the retracted position from the top of the sprinkler.
(4) Atmospheric vacuum breakers may be used if:
(A) No back-pressure will be present;
(B) There are no shutoff valves downstream from the atmospheric vacuum
breaker;
(C) The device is installed at a minimum of six inches above any downstream
piping and the highest downstream opening. Pop-up sprinklers are measured
from the retracted position from the top of the sprinkler;
(D) There is no continuous pressure on the supply side of the atmospheric
vacuum breaker for more than 12 hours in any 24-hour period; and
(E) A separate atmospheric vacuum breaker is installed on the discharge
side of each irrigation control valve, between the valve and all the
emission devices that the valve controls.
(c) Backflow
prevention devices used in applications designated as health hazards
must be tested upon installation and annually thereafter.
(d) If
there are no conditions that present a high health hazard, double
check valve backflow prevention assemblies may be used to prevent
backflow if the device is tested upon installation and test cocks
are used for testing only.
(e) If
a double check valve is installed below ground:
(1) Test cocks must be plugged, except when the double check valve is
being tested;
(2) Test cock plugs must be threaded, water-tight, and made of non-ferrous
material;
(3) A y-type strainer is installed on the inlet side of the double check
valve;
(4) There must be a clearance between any fill material and the bottom
of the double check valve to allow space for testing and repair; and
(5) There must be space on the side of the double check valve to test
and repair the double check valve.
(f) If
an existing irrigation system without a backflow-prevention assembly
requires major maintenance, alteration, repair, or service, the system
must be connected to the potable water supply through an approved,
properly installed backflow prevention method before any major maintenance,
alteration, repair, or service is performed.
(g) If
an irrigation system is connected to a potable water supply through
a double check valve, pressure vacuum breaker, or reduced pressure
principle backflow assembly and includes an automatic master valve
on the system, the automatic master valve must be installed on the
discharge side of the backflow prevention assembly.
(h) The
irrigator shall ensure the backflow prevention device is tested by
a licensed backflow prevention assembly tester approved by the city
prior to being placed in service and the test results provided to
the utilities department and the irrigation system’s owner or
owner’s representative within ten (10) business days of testing
of the backflow prevention device. The test results must be recorded
on a form provided by the city utilities department.
(Ordinance 2008-59 adopted 12/9/08)
(a) Before
any chemical is added to an irrigation system connected to the potable
water supply, the irrigation system must be connected through a reduced
pressure principle backflow prevention assembly or air gap.
(b) Connection
of any additional water source to an irrigation system that is connected
to the potable water supply is not allowed.
(c) Irrigation
system components with chemical additives induced by aspiration, injection,
or emission system connected to any potable water supply must be connected
through a reduced pressure principle backflow device.
(d) If
an irrigation system is designed or installed on a property that is
served by an on-site sewage facility, as defined in Title 30, Texas
Administrative Code, Chapter 285, then:
(1) All irrigation piping and valves must meet the separation distances
from the on-site sewage facilities system as required for a private
water line in title 30, Texas Administrative Code, section 285.91(10);
(2) Any connections using a private or public potable water source that
is not the city’s potable water system is prohibited; and
(3) Any water from the irrigation system that is applied to the surface
of the area utilized by the on-site sewage facility system must be
controlled on a separate irrigation zone or zones so as to allow complete
control of any irrigation to that area so that there will not be excess
water that would prevent the on-site sewage facilities system from
operating effectively.
(Ordinance 2008-59 adopted 12/9/08)
All irrigation systems shall be designed, installed, maintained, altered, repaired, serviced, and operated in a manner that will promote water conservation as defined in section
3-3-61 of this division.
(Ordinance 2008-59 adopted 12/9/08)
(a) An
irrigator shall prepare and submit an irrigation plan for each site
where a new irrigation system will be installed prior to installation
of the new system. A paper or electronic copy of the irrigation plan
must be on the job site at all times during the installation of the
irrigation system. A drawing showing the actual installation of the
system is due to each irrigation system owner after all new irrigation
system installations. During the installation of the irrigation system,
variances from the original plan may be authorized by the licensed
irrigator, after providing amended plan to city, if the variance from
the plan does not:
(1) Diminish the operational integrity of the irrigation system;
(2) Violate any requirements of this division; and
(3) Go unnoted in red on the irrigation plan.
(b) The
irrigation plan must include complete coverage of the area to be irrigated.
If a system does not provide complete coverage of the area to be irrigated,
it must be noted on the irrigation plan.
(c) All
irrigation plans used for construction must be drawn to scale. The
plan must include, at a minimum, the following information:
(1) The irrigator’s seal, signature, and date of signing;
(2) All major physical features and the boundaries of the areas to be
watered;
(5) The zone flow measurement for each zone;
(6) Location and type of each:
(B) Sensor (for example, but not limited to, rain, moisture, wind, flow,
or freeze);
(7) Location, type, and size of each:
(A) Water source, such as, but not limited to a water meter and point(s)
of connection;
(B) Backflow prevention device;
(C) Water emission device, including, but not limited to, spray heads,
rotary sprinkler heads, quick-couplers, bubblers, drip, or micro-sprays;
(D) Valve, including but not limited to, zone valves, master valves,
and isolation valves;
(E) Pressure regulation component; and
(F) Mainline and lateral piping.
(Ordinance 2008-59 adopted 12/9/08)
(a) No
irrigation design or installation shall require the use of any component,
including the water meter, in a way which exceeds the manufacturer’s
published performance limitations for the component.
(b) Spacing.
(1) The maximum spacing between emission devices must not exceed the
manufacturer’s published radius or spacing of the device(s).
The radius or spacing is determined by referring to the manufacturer’s
published specifications for a specific emission device at a specific
operating pressure.
(2) New irrigation systems shall not utilize aboveground spray emission
devices in landscapes that are less than 48 inches not including the
impervious surfaces in either length or width and which contain impervious
pedestrian or vehicular traffic surfaces along two or more perimeters.
If pop-up sprays or rotary sprinkler heads are used in a new irrigation
system, the sprinkler heads must direct flow away from any adjacent
surface and shall not be installed closer than four inches from a
hardscape, such as, but not limited to, a building foundation, fence,
concrete, asphalt, pavers, or stones set with mortar.
(3) Narrow paved walkways, jogging paths, golf cart paths or other small
areas located in cemeteries, parks, golf courses or other public areas
may be exempted from this requirement if the runoff drains into a
landscaped area.
(c) Water
pressure.
Emission devices must be installed to operate
at the minimum and not above the maximum sprinkler head pressure as
published by the manufacturer for the nozzle and head spacing that
is used. The emission devices must also be designed to accommodate
the city’s distribution system pressures. Methods to achieve
the water pressure requirements include, but are not limited to, flow
control valves, a pressure regulator, or pressure compensating spray
heads.
(d) Piping.
Piping in irrigation systems must be designed and installed
so that the flow of water in the pipe will not exceed a velocity of
five feet per second for polyvinyl chloride (PVC) pipe.
(e) Irrigation
zones.
Irrigation systems shall have separate zones based
on plant material type, microclimate factors, topographic features,
soil conditions, and hydrological requirements.
(f) Matched
precipitation rate.
Zones must be designed and installed
so that all of the emission devices in that zone irrigate at the same
precipitation rate.
(g) Irrigation
systems shall not spray water over surfaces made of concrete, asphalt,
brick, wood, stones set with mortar, or any other impervious material,
such as, but not limited to, walls, fences, sidewalks, streets, etc.
(h) Master
valve.
When provided, a master valve shall be installed
on the discharge side of the backflow prevention device on all new
installations.
(i) PVC
pipe primer solvent.
All new irrigation systems that
are installed using PVC pipe and fittings shall be primed with a colored
primer prior to applying the PVC cement in accordance with the Uniform
Plumbing Code (section 316) or the International Plumbing Code (section
605).
(j) Rain
or moisture shutoff devices or other technology.
All
new automatically controlled irrigation systems must include sensors
or other technology designed to inhibit or interrupt operation of
the irrigation system during periods of moisture or rainfall. Rain
or moisture shutoff technology must be installed according to the
manufacturer’s published recommendations. Repairs to existing
automatic irrigation systems that require replacement of an existing
controller must include a sensor or other technology designed to inhibit
or interrupt operation of the irrigation system during periods of
moisture or rainfall. [Cities in El Paso, Hudspeth, Culberson, Jeff
Davis, Presidio, Brewster, Terrell, Loving, Winkler, Ward, Reeves,
Ector, Crane and Pecos Counties are excluded from this requirement.]
(k) Isolation
valve.
All new irrigation systems must include an isolation
valve between the water meter and the backflow prevention device.
(l) Depth
coverage of piping.
Piping in all irrigation systems
must be installed according to the manufacturer’s published
specifications for depth coverage of piping.
(1) If the manufacturer has not published specifications for depth coverage
of piping, the piping must be installed to provide minimum depth coverage
of six inches of select backfill, between the top of the pipe and
the natural grade of the topsoil. All portions of the irrigation system
that fail to meet this standard must be noted on the irrigation plan.
If the area being irrigated has rock at a depth of six inches or less,
select backfill may be mounded over the pipe. Mounding must be noted
on the irrigation plan and discussed with the irrigation system owner
or owner’s representative to address any safety issues.
(2) If a utility, manmade structure, or roots create an unavoidable obstacle,
which makes the six-inch depth coverage requirement impractical, the
piping shall be installed to provide a minimum of two inches of select
backfill between the top of the pipe and the natural grade of the
topsoil.
(3) All trenches and holes created during installation of an irrigation
system must be backfilled and compacted to the original grade.
(m) Wiring
irrigation systems.
(1) Underground electrical wiring used to connect an automatic controller
to any electrical component of the irrigation system must be listed
by Underwriters Laboratories as acceptable for burial underground.
(2) Electrical wiring that connects any electrical components of an irrigation
system must be sized according to the manufacturer’s recommendation.
(3) Electrical wire splices which may be exposed to moisture must be
waterproof as certified by the wire splice manufacturer.
(4) Underground electrical wiring that connects an automatic controller
to any electrical component of the irrigation system must be buried
with a minimum of six inches of select backfill.
(n) Water
contained within the piping of an irrigation system is deemed to be
nonpotable. No drinking or domestic water usage, such as, but not
limited to, filling swimming pools or decorative fountains, shall
be connected to an irrigation system. If a hose bib (an outdoor water
faucet that has hose threads on the spout) is connected to an irrigation
system for the purpose of providing supplemental water to an area,
the hose bib must be installed using a quick coupler key on a quick
coupler installed in a covered purple valve box and the hose bib and
any hoses connected to the bib must be labeled “nonpotable,
not safe for drinking.” An isolation valve must be installed
upstream of a quick coupler connecting a hose bib to an irrigation
system.
(o) Beginning
January 1, 2010, either a licensed irrigator or a licensed irrigation
technician shall be on-site at all times while the landscape irrigation
system is being installed. When an irrigator is not onsite, the irrigator
shall be responsible for ensuring that a licensed irrigation technician
is on-site to supervise the installation of the irrigation system.
(Ordinance 2008-59 adopted 12/9/08)
Upon completion of the irrigation system, the irrigator or irrigation
technician who provided supervision for the on-site installation shall
be required to:
(1) Complete
a final “walk through” with the irrigation system’s
owner or the owner’s representative to explain the operation
of the system;
(2) Complete
the maintenance checklist on which the irrigator or irrigation technician
shall obtain the signature of the irrigation system’s owner
or owner’s representative and shall sign, date, and seal the
checklist. If the irrigation system’s owner or owner’s
representative is unwilling or unable to sign the maintenance checklist,
the irrigator shall note the time and date of the refusal on the irrigation
system’s owner or owner’s representative’s signature
line. The irrigation system owner or owner’s representative
will be given the original maintenance checklist and a duplicate copy
of the maintenance checklist shall be maintained by the irrigator.
The items on the maintenance checklist shall include but are not limited
to:
(A) The manufacturer’s manual for the automatic controller, if
the system is automatic;
(B) A seasonal (spring, summer, fall, winter) watering schedule based
on either current/real time evapotranspiration or monthly historical
reference evapotranspiration (historical ET) data, monthly effective
rainfall estimates, plant landscape coefficient factors, and site
factors;
(C) A list of components, such as the nozzle, or pump filters, and other
such components; that require maintenance and the recommended frequency
for the service; and
(D) The statement, “This irrigation system has been installed in
accordance with all applicable state and local laws, ordinances, rules,
regulations or orders. I have tested the system and determined that
it has been installed according to the irrigation plan and is properly
adjusted for the most efficient application of water at this time.”
(3) Affix
to each automatic controller installed by the irrigator or irrigation
technician, a permanent sticker which contains the irrigator’s
name, license number, company name, telephone number and the dates
of the warranty period. If the irrigation system is manual, the sticker
shall be affixed to the original maintenance checklist. The information
contained on the sticker must be printed with waterproof ink.
(4) The
irrigation plan indicating the actual installation of the system must
be provided to the irrigation system’s owner or owner representative.
(5) Confirmation
of backflow testing must be submitted to the irrigation system’s
owner or owner representative.
(Ordinance 2008-59 adopted 12/9/08)
(a) The
licensed irrigator is responsible for all work that the irrigator
performed during the maintenance, alteration, repair, or service of
an irrigation system during the warranty period. The irrigator or
business owner is not responsible for the professional negligence
of any other irrigator who subsequently conducts any irrigation service
on the same irrigation system.
(b) All
trenches and holes created during the maintenance, alteration, repair,
or service of an irrigation system must be returned to the original
grade with compacted select backfill.
(c) Colored
PVC pipe primer solvent must be used on all pipes and fittings used
in the maintenance, alteration, repair, or service of an irrigation
system in accordance with the Uniform Plumbing Code (section 316)
or the International Plumbing Code (section 605).
(d) When
maintenance, alteration, repair or service of an irrigation system
involves excavation work at the water meter or backflow prevention
device, an isolation valve shall be installed, if an isolation valve
is not present.
(Ordinance 2008-59 adopted 12/9/08)
Reclaimed water may be utilized in landscape irrigation systems
if:
(1) There
is no direct contact with edible crops, unless the crop is pasteurized
before consumption;
(2) The
irrigation system does not spray water across property lines that
do not belong to the irrigation system’s owner;
(3) The
irrigation system is installed using purple components;
(4) The
domestic potable water line is connected using an air gap or a reduced
pressure principle backflow prevention device, in accordance with
title 30, Texas Administrative Code, section 290.47(i) (relating to
appendices);
(5) A minimum
of an eight inch by eight inch sign, in English and Spanish, is prominently
posted on/in the area that is being irrigated, that reads, “RECLAIMED
WATER – DO NOT DRINK” and “AGUA DE RECUPERACIÓN
– NO BEBER”; and
(6) Backflow
prevention on the reclaimed water supply line shall be in accordance
with the regulations of the city’s water provider and must be
completely separate from the domestic potable water line.
(Ordinance 2008-59 adopted 12/9/08)
(a) All
vehicles used in the performance of irrigation installation, maintenance,
alteration, repair, or service must display the irrigator’s
license number in the form of “LI__________” in a contrasting
color of block letters at least two inches high, on both sides of
the vehicle.
(b) All
forms of written and electronic advertisements for irrigation services
must display the irrigator’s license number in the form of “LI__________.”
Any form of advertisement, including business cards, and estimates
which displays an entity’s or individual’s name other
than that of the licensed irrigator must also display the name of
the licensed irrigator and the licensed irrigator’s license
number. Trailers that advertise irrigation services must display the
irrigator’s license number.
(c) The
name, mailing address, and telephone number of the commission must
be prominently displayed on a legible sign and displayed in plain
view for the purpose of addressing complaints at the permanent structure
where irrigation business is primarily conducted and irrigation records
are kept.
(Ordinance 2008-59 adopted 12/9/08)
(a) All
contracts to install an irrigation system must be in writing and signed
by each party and must specify the irrigator’s name, license
number, business address, current business telephone numbers, the
date that each party signed the agreement, the total agreed price,
and must contain the statement, “Irrigation in Texas is regulated
by the Texas Commission on Environmental Quality (TCEQ), MC-178, P.O.
Box 13087, Austin, Texas 78711-3087. TCEQ’s website is:
www.tceq.state.tx.us.”
All contracts must include the irrigator’s seal, signature,
and date.
(b) All
written estimates, proposals, bids, and invoices relating to the installation
or repair of an irrigation system(s) must include the irrigator’s
name, license number, business address, current business telephone
number(s), and the statement: “Irrigation in Texas is regulated
by the Texas Commission On Environmental Quality (TCEQ) (MC-178),
P.O. Box 13087, Austin, Texas 78711-3087. TCEQ’s web site is:
www.tceq.state.tx.us.”
(c) An
individual who agrees by contract to provide irrigation services as
defined in title 30, Texas Administrative Code, section 344.30 (relating
to license required) shall hold an irrigator license issued under
title 30, Texas Administrative Code, chapter 30 (relating to occupational
licenses and registrations) unless the contract is a pass-through
contract as defined in title 30, Texas Administrative Code, section
344.1(36) (relating to definitions). If a pass-through contract includes
irrigation services, then the irrigation portion of the contract can
only be performed by a licensed irrigator. If an irrigator installs
a system pursuant to a pass-through contract, the irrigator shall
still be responsible for providing the irrigation system’s owner
or through contract, the irrigator shall still be responsible for
providing the irrigation system’s owner or owner’s representative
a copy of the warranty and all other documents required under this
article. A pass-through contract must identify by name and license
number the irrigator that will perform the work and must provide a
mechanism for contacting the irrigator for irrigation system warranty
work.
(d) The
contract must include the dates that the warranty is valid.
(Ordinance 2008-59 adopted 12/9/08)
(a) On
all installations of new irrigation systems, an irrigator shall present
the irrigation system’s owner or owner’s representative
with a written warranty covering materials and labor furnished in
the new installation of the irrigation system. The irrigator shall
be responsible for adhering to terms of the warranty. If the irrigator’s
warranty is less than the manufacturer’s warranty for the system
components, then the irrigator shall provide the irrigation system’s
owner or the owner’s representative with applicable information
regarding the manufacturer’s warranty period. The warranty must
include the irrigator’s seal, signature, and date. If the warranty
is part of an irrigator’s contract, a separate warranty document
is not required.
(b) An
irrigator’s written warranty on new irrigation systems must
specify the irrigator’s name, business address, and business
telephone number(s), must contain the signature of the irrigation
system’s owner or owner’s representative confirming receipt
of the warranty and must include the statement: “Irrigation
in Texas is regulated by the Texas Commission on Environmental Quality
(TCEQ), MC-178, P.O. Box 130897, Austin, Texas 78711-3087. TCEQ’s
website is:
www.tceq.state.tx.us.”
(c) On
all maintenance, alterations, repairs, or service to existing irrigation
systems, an irrigator shall present the irrigation system’s
owner or owner’s representative a written document that identifies
the materials furnished in the maintenance, alteration, repair, or
service. If a warranty is provided, the irrigator shall abide by the
terms. The warranty document must include the irrigator’s name
and business contact information.
(Ordinance 2008-59 adopted 12/9/08)
A licensed irrigation inspector shall enforce this division,
and shall be responsible for:
(1) Verifying
that the appropriate permits have been obtained for an irrigation
system and that the irrigator and installer or irrigation technician,
if applicable, are licensed;
(2) Inspecting
the irrigation system;
(3) Determining
that the irrigation system complies with the requirements of this
article;
(4) Determining
that the appropriate backflow prevention device was installed, tested,
and test results provided to the city;
(5) Investigating
complaints related to irrigation system installation, maintenance,
alteration, repairs, or service of an irrigation system and advertisement
of irrigation services; and
(6) Maintaining
records according to this article.
(Ordinance 2008-59 adopted 12/9/08)
Any item not covered by this division and required by law shall
be governed by the Texas Occupations Code, the Texas Water Code, title
30 of the Texas Administrative Code, and any other applicable state
statute or Texas Commission on Environmental Quality rule.
(Ordinance 2008-59 adopted 12/9/08)
The city council may create a schedule of fees for obtaining
and renewing an irrigation permit. These fees will be in amounts sufficient
to cover the city’s costs in issuing and renewing the permits,
including, but not limited to, staff time and other overhead costs.
This schedule [will be kept at the city offices/may be found in Appendix
A/etc.] [sic].
(Ordinance 2008-59 adopted 12/9/08)
(a) The
city shall have the power to administer and enforce the provisions
of this article as may be required by governing law. Any person, firm,
corporation or agent who shall violate a provision of this code, or
fails to comply therewith, or with any of the requirements thereof,
is subject to suit for injunctive relief as well as prosecution for
criminal violations. Any violation of this division is declared to
be a nuisance.
(b) Any
person violating any provision of this division shall, upon conviction,
be fined a sum not exceeding $2,000.00. Each day that a provision
of this division is violated shall constitute a separate offense.
An offense under this division is a class C misdemeanor, punishable
by a fine of up to $2,000.00.
(c) Nothing
in this division shall be construed as a waiver of the city’s
right to bring a civil action to enforce the provisions of this division
and to seek remedies as allowed by law, including, but not limited
to the following:
(1) Injunctive relief to prevent specific conduct that violates this
division or to require specific conduct that is necessary for compliance
with this division; and
(Ordinance 2008-59 adopted 12/9/08)