The purpose of this Chapter is to assure that subdivision and site development projects constructed within the City of Liberty Hill and its extraterritorial jurisdiction (ETJ), are adequately furnished with necessary public infrastructure. These include water, wastewater, stormwater drainage, roads, and open space resources.
Design and construction of infrastructure in the City and ETJ shall be consistent with the policies and guidelines established in the most recent versions of the Liberty Hill Comprehensive Plan. Any interpretation of the requirements of this Section shall be made in a manner consistent with the Comprehensive Plan.
(Ordinance 09-O-02 adopted 1/28/2009)
This chapter addresses policies contained in the Comprehensive Plan and legal requirements for the adequate provision of infrastructure for the health, safety, and welfare of the residents of the City of Liberty Hill and its surroundings.
(Ordinance 09-O-02 adopted 1/28/2009)
5.03.01 
Unapproved Final Plat or Site Development.
City approvals, including but not limited to building, repair, plumbing, or electrical permits, shall not be issued by the City for any structure on a lot in a subdivision or on a parcel for which a final plat or site development permit has not been approved and filed for record.
5.03.02 
Compliance with Standards.
Full compliance with the standards contained within this Code must be obtained before the issuance of a building repair, plumbing or electrical permit for any structure on a lot within a subdivision within the jurisdiction of the City.
5.03.03 
Review, Permit and Enforcement Authority.
In fulfilling any responsibilities in this Section that require technical or other expertise, the City Manager or designee of the Council shall rely on the assistance of City Engineer or another designee for such expertise.
5.03.04 
No City Maintenance.
The City shall not repair, maintain, install or provide any streets or public utilities or services in any subdivision for which a final plat has not been approved and filed for record, nor any parcel or lot for which a site development permit has not been issued, nor in which the standards contained herein or referred to herein have not been complied with in full.
5.03.05 
No Utility Service.
The City shall not sell or supply water, gas, electricity or sewerage within a subdivision for which a final plat has not been approved and filed for record, or parcel or lot for which a site development permit has not been issued, nor in which the standards contained herein have not been complied with in full.
5.03.06 
Grandfather Provisions.
The provisions of this Section shall not be construed to prohibit the issuance of permits for any lot or undivided tract or parcel of land upon which a structure exists that was in existence prior to the passage of this Code.
5.03.07 
Required Improvements.
In the absence of any provision to the contrary, the subdivider, developer or applicant shall provide the following improvements, as approved in the construction plans, in conformance with the standards, specifications and requirements of this Unified Development Code:
A. 
Streets including rights-of-way, alleys, sidewalks, bridges, signalization, and street lighting;
B. 
Water system including utility easements, water distribution lines, fire hydrants, valves, pumps, and water towers in conformance with the terms and regulations of the provider of said utility;
C. 
Sanitary sewer system including utility easements, sanitary sewer lines, manholes, and lift stations in conformance with the terms and regulations of the provider of said utility;
D. 
Drainage system including drainage easements, channels, storm sewer lines and inlets, basins, control structures, and landscaping;
E. 
Park land;
F. 
Permanent monument markers;
G. 
Utilities for electric and telephone service and associated utility easements installed in conformance with the terms and regulations of the provider of said utility;
H. 
Gas, cable television and other telecommunications service and associated utility easements, when provided, installed in conformance with the terms and regulations of the provider of said utility.
5.03.08 
Improvement Continuity and Integration.
All improvements must be designed and installed so as to provide for a logical system of utilities, drainage and streets and to create continuity of improvements for the development of adjacent properties. Pedestrian, vehicle, water, wastewater and drainage improvements must be extended to the perimeter of a subdivision.
5.03.09 
Improvement Plans.
Plans for the improvements required by this Chapter shall be prepared and approved in accordance with the provisions contained herein and certified for accuracy and completeness by a registered professional engineer licensed by the State of Texas.
After completion of construction, the developer shall deliver to the City as-built construction documents indicating all improvements, new construction, and upgrades. These documents shall clearly indicate the location of all improvements including the location of above- and below-ground utilities. The documents shall include a certification from a licensed Professional Engineer that all construction required by this code was performed in compliance with the standards and specifications required of this code.
5.03.10 
Acceptance of Improvements.
During the course of installation and construction of the required improvements, the City Engineer or another designee of the City Manager shall make periodic inspections of the work to insure that all improvements comply with this Code and other municipal, county and State requirements. Upon completion of installation and construction of all required improvements, the developer may seek acceptance of all public improvements by the City by submitting the required number of copies of as-built plans and a one-year maintenance bond in an amount as specified at the time of final plat submittal. In addition, the developer shall provide a statement signed by a registered professional engineer that all improvements have been installed and constructed in accordance with the submitted as-built plans.
5.03.11 
Maintenance and Supervision.
Where a subdivision contains sewers, sewage treatment facilities, water supply systems, parks and grounds held in common, drainage facilities, or other physical facilities necessary or desirable for the welfare of the area, or that are of common use or benefit which are not or cannot be satisfactorily maintained by an existing public agency, provision shall be made which is acceptable to the City for the proper and continuous operation, maintenance, and supervision of such facilities. A copy of the agreements providing for the proper and continuous operation, maintenance and supervision of such facilities shall be presented to the City Manager and approved as to form by the City Attorney at the time of final plat approval or site development permit issuance and shall be filed of record with the plat or permit thereof.
(Ordinance 09-O-02 adopted 1/28/2009)
A. 
A final plat or replat or site development permit will not be approved unless the land proposed for subdivision or site development is adequately served by essential public facilities and services. These services include:
1. 
Streets including alleys, bridges and street lighting, rights-of-way, sidewalks, signalization.
2. 
Water system including wells (where used), utility easements, water distribution lines, fire hydrants, valves, pumps, pressure tanks, water towers and other water facilities.
3. 
Sanitary sewer system including utility easements, sanitary sewer lines, manholes, and lift stations.
4. 
Drainage system including drainage easements, culverts, channels, storm sewer lines and inlets, basins, control structures, and landscaping.
5. 
Park land in accordance with parkland dedication requirements.
6. 
Utilities for electric and telephone service and associated utility easements shall be installed in conformance with the terms and regulations of the provider of said utility[.]
7. 
Gas and cable television service and other telecommunications service and associated utility easements, when provided, shall be installed in conformance with the terms and regulations of the provider of said utility.
B. 
The City of Round Rock’s Design and Construction Standards shall apply for all public facilities within the City limits and ETJ of Liberty Hill. This policy may be further defined and supplemented by other codes adopted by the City.
C. 
Where appropriate, a letter from each respective utility service provider (when such utility is not provided by the City of Liberty Hill) which states that all requirements have been met, is sufficient in meeting the intent of this section.
(Ordinance 09-O-02 adopted 1/28/2009)
5.05.01 
Purpose and Intent.
A. 
All streets shall be planned to properly integrate with the existing and proposed system of local, collector and arterial streets.
B. 
Local streets shall be designed to conform to existing topography, to discourage use by through traffic, to permit efficient drainage and utility installation, and provide safe access to property.
C. 
Streets shall be provided to the boundary lines of the tract being subdivided, unless the City Manager or designee determines that such an extension is neither necessary, nor desirable.
D. 
All plats shall provide for the appropriate extension and connection of existing and proposed streets in accordance with the City Thoroughfare Plan and any other extensions and connections deemed necessary by the City Manager or designee.
E. 
Intersections shall be designed to accommodate anticipated traffic generators such as schools, businesses, shopping centers, and population densities. Streets should be designed with safety for all modes of travel as the primary priority.
F. 
The location of arterial streets shall conform to the City Thoroughfare Plan.
G. 
Curbing shall be required for the purpose of drainage, safety, delineation, and protection of the pavement edge. Curbing shall be designed so as not to interfere with the movement of pedestrian traffic.
H. 
Except where indicated sidewalks shall be required on both sides of all streets.
I. 
Streets and improvements associated with streets shall be in accordance with the City of Round Rock’s Design and Construction Standards.
J. 
Streets shall provide adequate access for emergency and service vehicles, enhance walkability by ensuring connected transportation routes, and provide continuous and comprehensible traffic routes.
5.05.02 
Street Design Standards.
A. 
Street Classification and Characteristics.
1. 
Local Streets.
The purpose of a local street is to provide lot street frontage and carry traffic to a higher classification street. Local streets are divided into three subcategories: Local-residential, local-nonresidential or local-rural. Unless approved by the City Manager or designee, a local street shall not connect to two separate higher classification streets or connect directly to arterial streets. Local streets may be designated as private streets.
2. 
Collector Streets.
Collector streets are divided into two subcategories: Local and major. The purpose of collector streets is to convey traffic from intersecting local streets and to expedite the movement of traffic to an arterial street or other collector street. No collector street in a residential development shall be designated as a private street. Collector streets in nonresidential private street developments may be designated as private streets.
3. 
Arterial Streets.
The purpose of an arterial street is to carry high volumes of through traffic. Arterial streets serve as a link between major activity centers within the urban area. Access is usually limited to intersections, multifamily developments and commercial driveways. All arterial streets are designated in the City Thoroughfare Plan. An arterial street shall not end as a cul-de-sac. Generally, arterial streets shall not permit on-street parking. No arterial street shall be designated as a private street.
B. 
New Streets.
1. 
Right-of-Way.
A developer shall dedicate or convey at the city’s option the amount of right-of-way for each type of street as stated in the City of Round Rock’s City of Round Rock’s [sic] Design and Construction Standards. Except as provided below, the developer must dedicate or convey the required right-of-way for all streets within the subdivision as shown on the plat. The city may reduce the amount of right-of-way dedication for an arterial street based on the design consideration, existing land uses, existing development of adjoining properties, and dimensions of the proposed addition or subdivision. In all cases, the amount of right-of-way dedicated for any one street within the addition or subdivision shall not exceed one hundred and twenty (120) feet wide or fifteen percent (15%) of the total acreage on the plat submitted.
2. 
Street Improvements.
All public and private streets shall be designed and built in accordance with the City of Round Rock’s Design and Construction Standards. The developer must construct the full cross-section of the arterial streets designated on the City Thoroughfare Plan which are located within the subdivision unless approval [is obtained] from the City Manager or designee depicting alternative standards per the TIA criteria in section 6.11.06 Traffic Impact Analysis.
3. 
Private Streets.
Private streets are discouraged and may only be permitted, with approval of the Planning & Zoning Commission and the City Council.
4. 
Substandard Existing Street Right-Of-Way.
Whenever a proposed subdivision abuts an existing street that has a substandard right-of-way width for either the existing street or for a future street, the developer shall dedicate the additional right-of-way for the existing street or future street. The developer shall dedicate one-half of the amount required for the type of street to be upgraded measured from the existing centerline of the right-of-way or up to fifteen percent (15%) of the total acreage of the addition or subdivision, whichever is less. The city may reduce the amount of right-of-way dedication requirement based on design consideration, existing land uses, existing development of adjacent properties, and dimensions of the proposed addition or subdivision.
C. 
Stub Streets.
Except for gated communities, a proposed subdivision or addition must provide access to adjacent land subdivided by stubbing appropriate streets to the boundaries of the proposed addition or subdivision. When the abutting land is platted, the developer shall integrate the stubbed streets into the existing traffic system of streets in a logical manner as well as continue the same street classification of the stub street. The developer shall present a schematic plan to demonstrate how the stub street will eventually extend through the adjacent property and connect with a collector or arterial street. Temporary paved turnarounds shall be provided at the end of stubbed streets which are more than two hundred and fifty (250) feet long.
D. 
Cu-de-sacs.
1. 
Cul-de-sacs are discouraged and shall only be allowed if no secondary access can be reasonably provided to the portion of the subdivision which is to be served by the cul-de-sac or if there is limited access to the subdivision is due to a topographical condition on the property or a particular physical condition.
2. 
Only local streets may terminate in a cul-de-sac. Collectors and arterial streets may not terminate in a cul-de-sac.
3. 
The maximum length of a cul-de-sac street shall be six hundred (600) feet.
E. 
Curbing.
All streets shall have standard curbing and gutter except for the local-rural street classification where ribbon curb is allowed. All raised medians and islands located within the street pavement shall be bordered by standard curb and gutter, unless otherwise approved by the City Engineer. All concrete curb and gutter shall be installed and constructed according to the City of Round Rock’s Design and Construction Standards.
F. 
Curb ramps.
1. 
Curb ramps are required within a street wherever a sidewalk or pedestrian route intersects with a curb. The design and construction of curb ramps shall be in accordance with the City of Round Rock’s Design and Construction Standards, and shall meet the Texas Accessibility Standards, administered by the state department of licensing and regulation and the Americans with Disabilities Act of 1990, as amended.
2. 
Whenever a sidewalk or pedestrian route crosses a raised median, the raised median shall be cut through level with the street or shall have curb ramps at both median curbs plus a level area at least four (4) feet long between the curb ramps in the median.
G. 
Access.
All lots shall be provided with frontage on an existing or proposed public or private street.
5.05.03 
Connectivity.
Subdivisions shall have a minimum number of connections to public roads and a minimum number of stub streets where necessary to connect to future subdivisions on adjacent tracts of land as follows:
A. 
Less than 75 lots: one (1) connection to a public road and one (1) stub street;
B. 
For 75 lots up to 150 lots: two (2) connections to a public road and one (1) stub street;
C. 
For 151 lots up to 300 lots: three (3) connections to a public road and two (2) stub streets;
D. 
For 301 lots up to 400 lots: four (4) connections to a public road and three (3) stub streets;
E. 
For 401 lots up to 500 lots: five (5) connections to a public road and four (4) stub streets;
F. 
For 501 lots up to 800 lots: six (6) connections to a public road and five (5) stub streets;
G. 
For 801 lots and more: one (1) additional connection to a public road and one (1) additional stub street for each additional 200 lots;
H. 
One (1) additional stub street may substitute for one (1) public road connection requirement if a minimum of two (2) connections are provided.
5.05.04 
Medians and Islands.
A. 
Standards.
Medians and islands shall be landscaped with landscape materials from the Austin Grow Green Guide, the preferred plant list in Section 6.06.18, or constructed of stamped pattern concrete, brick, stone or concrete pavers. Grass turf areas shall not be less than six (6) feet in width. All medians and islands shall be bordered by standard curb and gutter.
B. 
Median openings.
Median openings on arterial streets shall be in accordance with the City of Round Rock’s Design and Construction Standards.
5.05.05 
Intersections.
A. 
Proposed intersections shall be designed to meet the minimum spacing requirements, curb radii, and corner sight distances required in the City of Round Rock’s Design and Construction Standards, and based on the following design specifications:
B. 
Streets shall intersect at right angles or up to twenty (20) degrees from a right angle to accommodate sign design or constraints.
C. 
The right-of-way line at street intersections shall be in accordance with the City of Round Rock’s Design and Construction Standards.
D. 
The centerline of intersecting streets shall be a minimum of two hundred (200) feet from other street intersections. This offset shall not apply to streets intersecting a street if a raised median is provided and no median opening is aligned with either of the offset streets. Future median openings are prohibited where two streets offset and intersect an arterial street at a distance of less than two hundred (200) feet; provided, however, median openings may be allowed for one-way traffic circulation subject to the approval of the City Manager or designee.
5.05.06 
Acceleration/Deceleration Lanes.
A. 
Acceleration/deceleration lanes shall be provided along existing and proposed arterial streets when required by the findings of a city-approved TIA.
B. 
Additional right-of-way shall be dedicated by plat if required to accommodate acceleration/deceleration lanes or turning lanes.
5.05.07 
Street Names and Addresses.
A. 
Street names.
Each preliminary plat shall indicate proposed street names for streets within the addition or subdivision. The City Manager or designee and County 911 addressing authorities shall review and approve the proposed street names according to the following standards:
1. 
Street names shall not conflict with or duplicate any existing street names within Williamson County. The disapproval of a proposed street name may be based on but is not limited to the following: close pronunciation to another street name, street name is too difficult to pronounce, street names with undesirable meanings or connotations, street names with language translation problems or street names that may cause the theft of a street sign.
2. 
New streets which are extensions or in alignment with existing streets shall bear the name of the existing street.
3. 
Street suffix terms shall be assigned in accordance with the policy of the County 911 addressing authorities.
B. 
Final plat.
Approved street names shall be shown on the final plat.
C. 
Street addresses.
Street addresses shall be assigned by Williamson County Addressing.
(Ordinance 09-O-02 adopted 1/28/2009; Ordinance 2022-O-12.14-02 adopted 12/14/2022)
A plat or replat or site development permit will not be approved unless lighting requirements as defined in this Code are met.
(Ordinance 09-O-02 adopted 1/28/2009)
A plat or replat or site development permit will not be approved unless the proposed lot(s) or development is connected to a water supply system which is capable of providing adequate water for health and emergency purposes. Except for lots along an approved cul-de-sac or where it is impracticable, all lots must be provided service connections from a looped water main providing water flow from two directions or sources. New developments or improvements of existing developments should consult the City of Liberty Hill or appropriate utility provider for compliance.
(Ordinance 09-O-02 adopted 1/28/2009)
A plat or replat or site development permit will not be approved unless the proposed lot(s) or site developments are served by an approved means of wastewater collection and treatment. The projected wastewater discharge of a proposed development shall not exceed the proposed capacity of the proposed development’s wastewater system. The City may require the phasing of development and/or improvements to the systems so as to maintain adequate wastewater capacity. New developments or improvements of existing developments should consult the City of Liberty Hill or appropriate wastewater utility service provider for compliance.
(Ordinance 09-O-02 adopted 1/28/2009)
Water service must be sufficient to meet the fire flow requirements of the proposed development, except where a suitable alternative means of fire protection is approved by the City Volunteer Fire Department Chief, or his designee, and the City Engineer. The City may require the phasing of development, and/or the construction of improvements to maintain adequate fire protection.
(Ordinance 09-O-02 adopted 1/28/2009)
Increased stormwater runoff attributable to new development must not exceed the capacity of the downstream drainage systems or adversely affect adjoining property. Where the projected runoff would exceed capacity based on the standards specified in this Code, the City may require the phasing of development, the use of control methods such as retention or detention, and/or the construction of off-site drainage improvements as means of mitigation. New developments or improvements of existing developments should consult the City of Liberty Hill for compliance.
(Ordinance 09-O-02 adopted 1/28/2009)
(a) 
The provision of adequate parkland for use as parks is necessary for the protection of public health, safety and general welfare of the community. The City has attempted to provide parks to serve the immediate recreational needs of residents near their homes, but it faces a severe shortage of local recreational space as new subdivisions are approved and the City’s population grows. Accordingly, it appears that the provision of parks can best be accomplished in conjunction with the platting and development of new residential areas, which increase the need for parkland and whose residents will be direct beneficiaries of the provision of such parkland.
(b) 
The subdividers of all residential subdivisions shall be required to provide for the parkland needs of future residents through the clear fee simple dedication of suitable land for park and recreational purposes. This requirement shall include the residential portions of any Planned Unit Development (PUD). Commercial subdivisions and a single-family subdivision of one lot, having met the platting requirements to facilitate construction of a single-family residence, shall not be subject to the parkland dedication requirements of this section.
(c) 
The subdivider shall dedicate parkland to the City as a part of the final plat approval. The area to be dedicated for the purpose of parkland shall be shown on the conceptual plan, the preliminary plat, and the final plat, and shall be included in the dedication statement. The parkland shall be dedicated to the City by general warranty deed, and acceptable evidence of clear title and evidence that all taxes have been paid shall be furnished by the City.
The City Council shall have the discretion to forego the transfer of the general warranty deed to the City of Liberty Hill in favor of transferring the land dedication to the Texas Parks and Recreation Foundation to act as a holding agent for the real property that will eventually become public parks or open space. The transfer of the land dedication to the Texas Parks and Recreation Foundation may be used for in-kind grant matches for park development grants in accordance with State regulations[.]
(d) 
The minimum amount of land required to be dedicated as parkland shall be 8% of the total subdivision acreage proposed for residential use, excluding acreage within the 100-year floodplain.
(e) 
Land dedicated for park and recreational purposes shall be of size, character, and location consistent with the standards outlined below:
(1) 
If necessary for optimum park placement, large dedicatory requirements under this section may be accomplished by dedication of two or more separate park sites as long as the combined area meets the requirements set out in this section.
(2) 
The dedicated parkland shall provide a minimum of 50 feet of frontage on a dedicated public street or of a width acceptable to the parks board and the City.
(3) 
At least 50% of the dedicated parkland shall be level, well-drained, and suitable for use as an open playfield.
(4) 
Water and wastewater connections shall be readily available at the park site with water and wastewater lines located along the street frontage of the park. The subdivider must demonstrate that there is sufficient water and wastewater utility line capacity available to serve the park.
(5) 
The area shall not be subject to any reservation of record, encumbrances of any kind, or easements which will interfere with the use of the land for park or recreational purposes.
(f) 
All land proposed for dedication as parkland that is located in a floodplain area shall:
(1) 
Be easily accessible and have adequate street frontage;
(2) 
Have any alteration of its natural character and that of its waterway approved by the parks board and City;
(3) 
Be at least 100 feet in width, or of a width acceptable to the parks board and the City;
(4) 
Have a configuration and topography suitable for placement of facilities such as playgrounds, picnic facilities, and open playfields.
(g) 
If a subdivider is unable to meet the standards set out in subsections (d) and (e) above, resort may be had to one or more of the following alternatives:
(1) 
Dedication by the subdivider of a unique area of natural beauty or an area possessing unique natural features or biologically valuable qualities;
(2) 
The combination of two or more required dedications to form a single, viable park area;
(3) 
Land dedication that would expand existing parks or recreation facilities; and/or
(4) 
Transfer of required parkland dedication in one subdivision to another location owned by the same subdivider.
(h) 
When an area is required to be dedicated, the City may require a cash payment in lieu of dedication or parkland.
(1) 
Where with respect to a particular subdivision the City council determines that a subdivider is unable to meet the requirements of subsections (e), (f) and (g) above, the subdivider may be required to deposit a cash payment with the City. The amount of such cash payments shall be in accordance with the provisions set out in this section. Alternatively, the City may accept a combination of parkland dedication and a cash payment in lieu of a portion of the parkland dedication.
(2) 
All cash payments shall be used exclusively for the acquisition and/or improvement of parks.
(i) 
The amount of cash payment to be made to the City shall be 8% of the fair market value of the land proposed to be subdivided, as determined by a qualified real estate appraiser employed by the city, less a credit for the value of the land actually dedicated for parkland as determined by such real estate appraiser. A subdivider, at his own expense, may obtain an additional appraisal by a qualified real estate appraiser mutually agreed upon by the city and the subdivider. In such case, the City Council shall determine fair market value upon consideration of both the appraisals.
(j) 
All required cash payments must be submitted prior to final plat approval.
(k) 
Fifty percent of land contained within the 100-year floodplain shall be credited against the parkland dedication requirement; provided that adjoining land within the 25-year floodplain is also dedicated. Land within the 25-year floodplain shall not be credited against the parkland dedication requirement.
(l) 
Unless otherwise specified, the requirements of this section shall apply to all residential subdivisions. Exemptions from the provisions of this section shall be as follows:
(1) 
Any resubdivision of land that does not increase the allowed number of dwelling units;
(2) 
A subdivision for which a preliminary plat was approved on or before the effective date of this article, and which preliminary plat has not expired prior to approval of a final plat; or
(3) 
Where there has been entered into a special agreement with the City including specific provisions for the dedication of parkland or cash payments or in lieu of the requirements of this section.
(m) 
Any land that is dedicated as parkland and is disturbed during construction of the subdivision must be restored by the developer to its original condition or better prior to release of fiscal for the subdivision.
A plat or replat or site development permit will not be approved unless adequate parks and recreational requirements are provided, based on the standards specified in this Code. All residential developments will be required to comply with these standards and requirements. It is the intent of this Code that parks and recreational facilities are located and constructed to provide adequate capacity and functionality to the residents they serve and provide safe, healthy recreational opportunities to the community.
(n) 
City Council shall have the discretion to approve any combination of dedicated parkland or fee in lieu of a land dedication to serve the best interests of the citizens of Liberty Hill.
(Ordinance 09-O-02 adopted 1/28/2009; Ordinance 22-O-04.27-01 adopted 4/27/2022; Ordinance 2022-O-11.09-04 adopted 11/9/2022)
A plat or replat or site development permit will not be approved unless the following monument and ground control requirements of this Code are met:
A. 
All monuments and control points shall be placed by a licensed land surveyor, and must be in place prior to the installation of any roadway improvements.
B. 
To the extent it is practicable, monuments should be installed in locations that will prevent disturbance or destruction of the monument by construction activities. Any monuments disturbed or destroyed during roadway construction shall be reestablished in conformance with the provisions of this Code by a licensed land surveyor.
C. 
All corners of subdivisions and points of curvature (P.C.) and points of tangency (P.T.) along boundary lines of subdivisions shall be marked with a one-half inch iron rod, two feet in length, set in the center of a concrete monument six (6) inches in diameter and thirty (30) inches deep, with the top of the concrete monument set flush with the finished ground surface.
D. 
Where, due to topographic conditions, permanent structures, or other conditions, the view is obstructed between any two adjacent monuments, intermediate monuments shall be set as to assure a clear view between adjacent monuments.
E. 
Corner markers shall be a one-half inch iron rod, or three-fourths inch pipe, two feet in length, and shall be installed flush with the ground. Corners of all lots, block corners, street right-of-way P.C.s and P.T.s shall be marked with corner markers.
F. 
One permanent benchmark must be installed and referenced to the North American Datum 1983 and the State Plane Coordinate System (Texas State Plane grid coordinates, Central Zone, Feet). Surface coordinates may be provided, but should include a scale factor and convergence to reflect grid coordinates. The City Manager may waive the requirement for installations of a benchmark for subdivisions smaller than 50 acres when at least two benchmarks are located within one-half mile of the proposed subdivision boundaries.
The landowner or developer shall be required to comply with all the requirements for Fiscal Surety relating to Construction and Maintenance as detailed in Chapter 7.
(Ordinance 09-O-02 adopted 1/28/2009)