This article lists the land uses that may be allowed within the agriculture and residential zoning districts established by Section
9-3.102 (Zoning Districts), determines the type of planning permit/approval required for each use, and provides basic lot size and development standards for specific zones.
(Ord. 602 § 2, 2016)
The purposes of the individual agriculture and residential zoning
districts and the manner in which they are applied are as follows:
(a) A
(Agriculture) Zoning District. This zone is established to protect,
preserve and encourage agriculture on suitable land. The Agriculture
Zone is intended to support and encourage the continuation of the
Agricultural Preserve Program and the maintenance of productive open
space.
(b) RS
(Residential Suburban) Zoning District. This zone is established to
provide for large lot residential uses in areas outside the urban
services line or in other areas where large lots are desirable to
protect land uses and buildings subject to inundation, steep slopes
or other hazards.
(c) RSF
(Residential Zoning Family) Zoning District. This zone is established
to provide for single-family residential areas within the urban services
line.
(d) LSF
(Limited Single-Family) Zoning District. This zone is established
to provide for single-family residential areas within the urban services
line where the raising of farm animals would not be allowable.
(e) RMF
(Residential Multifamily) Zoning District. This zone is established
to provide for apartment, condominium, townhouse development, and
other small lot residential products, where higher density residential
development is desired within the urban services line.
(Ord. 602 § 2, 2016)
Table 3-1 identifies the uses of land allowed this Zoning Code
in each agriculture and residential district, and the planning permit
required to establish each use, in compliance with Section 9-1 and
Section 9-2 of this code. Where the last column in the tables ("Specific
Use Regulations") includes a section number, the regulations in the
referenced section apply to the use. Provisions in other sections
of this article may also apply.
(Ord. 602 § 2, 2016; Ord. 614 § 4, 2017; Ord. 646 § 11, 2021)
New subdivisions and the densities of agriculture and residential development shall comply with the requirement for lot sizes in Sections
9-3.241 through
9-3.245.
(Ord. 602 § 2, 2016)
The minimum lot size in the Agriculture Zone shall be established
by the minimum area needed to maintain productive agricultural use
of the property.
(Ord. 602 § 2, 2016)
The minimum lot size in the Residential Suburban Zone shall
be two and one-half (2 1/2) acres and may range up to 10 acres depending
upon conformance with performance standards established in this section.
(a) Performance
Standards. The following performance standards shall be evaluated
for each lot in determining its minimum lot size:
(1) Distance from the Center of the Community. Using the Atascadero Administration
Building as the center of the community, the lot size factor based
on this performance standard shall be:
Distance*
|
Lot Size Factor
|
---|
0 — 8,000′
|
0.20
|
8,000′ — 10,000′
|
0.25
|
10,000′ — 12,000′
|
0.30
|
12,000′ — 14,000′
|
0.40
|
14,000′ — 16,000′
|
0.50
|
16,000′ — 18,000′
|
0.60
|
18,000′ — 20,000′
|
0.75
|
20,000′ +
|
0.90
|
*
|
To be measured as radial distance using map maintained in Planning
Department.
|
(2) Septic Suitability. Using generalized soils data from the Natural
Resources Conservation Service Reports, the lot size factor based
on this performance standard shall be:
NRCS Rating*
|
Lot Size Factor
|
---|
Well suited
|
0.50
|
Moderate
|
0.75
|
Slow
|
1.00
|
Severe
|
1.50
|
*
|
Refer to map maintained in Community Development Department.
|
Percolation tests may be substituted for the Natural
Resources Conservation Service Reports. These shall be prepared by
a registered civil engineer or licensed sanitarian. The following
conversion chart shall be used to determine the appropriate lot size
factor:
Percolation Rating
|
Minutes Per Inch
|
---|
Well suited
|
Less than 20
|
Moderate or slow
|
20 to 39
|
Slow
|
40 to 59
|
Severe
|
Greater than 60
|
(3) Average Slope. Using the Basic, Sectional or Contour Measurement
Method, the lot size factor based on this performance standard shall
be:
Slope
|
Lot Size Factor
|
---|
0 — 10%
|
0.50
|
11 — 20%
|
0.75
|
21 — 25%
|
1.00
|
26 — 30%
|
1.25
|
31 — 35%
|
1.75
|
36 — 40%
|
2.00
|
40% +
|
2.25
|
(4) Condition of Access. Using the road right-of-way with the shortest
accessible distance between a lot and an improved collector road,
the lot size factor based on this performance standard shall be:
Condition
|
Lot Size Factor
|
---|
City accepted road
|
0.40
|
Paved road, less than 15% slope
|
0.40
|
Paved road, greater than 15% slope
|
0.50
|
All-weather road, less than 15% slope
|
0.75
|
All-weather road, greater than 15% slope
|
1.00
|
Unimproved road, less than 15% slope
|
1.25
|
Unimproved road, greater than 15% slope
|
1.50
|
(5) General Neighborhood Character. Using the average lot size of existing
lots which are zoned for single-family residential use (except that
lots larger than 15 acres shall be excluded unless they constitute
more than 25% of the total number of lots) within a 1,500 foot radius,
the minimum lot size factor based on this performance standard shall
be determined by multiplying the average lot size by 0.2.
(b) Determination of Minimum Lot Size. The minimum lot size shall be determined by the sum of each of the lot size factors for the performance standards set forth in subsection
(a) of this section, however in no case shall the minimum lot size be less than two and one-half (2-1/2) acres in size.
(1) The most current information shall be used to determine the lot size
factor. Where information is not available, the Planning Director
shall determine which lot size factor shall apply.
(2) If more than one lot size factor can be applied to a lot, the less
restrictive factor shall be used.
(3) Lot size factors shall be based on conditions in existence at the
time of filing an application unless information is included with
the application which will alter a lot size factor.
(Ord. 602 § 2, 2016; Ord. 614 § 4, 2017)
The minimum lot size in the Residential Single-Family Zone shall be 1/2 acre and may range up to two and one-half (2-1/2) acres. The size of a lot shall be consistent with the land use designation set forth in the General Plan and shall be indicated by the symbols set forth in the following chart, which shall be shown on the official zoning maps as provided by Section
9-3.104(d).
Symbol
|
Minimum Lot Size
|
---|
X
|
1/2 acre net area (excluding land needed for street rights-of-way
whether publicly or privately owned).
|
Y
|
1 acre gross area.
|
Z
|
1-1/2 to 2-1/2 acres gross based on performance standards set
forth in this section.
|
(a) Performance
Standards. The following performance standards shall be evaluated
for each lot which is appended with the "Z" symbol in determining
its minimum lot size:
(1) Distance from the Center of the Community. Using the Atascadero Administration
Building as the center of the community, the lot size factor based
on this performance standard shall be:
Distance*
|
Lot Size Factor
|
---|
0—4,000′
|
0.08
|
4,000′—6,000′
|
0.10
|
6,000′—8,000′
|
0.12
|
*
|
To be measured as radial distance using map maintained in the
Planning Department.
|
(2) Septic Suitability. Using generalized soils data from the Natural
Resources Conservation Service Reports, the lot size factor based
on this performance standard shall be:
NRCS Rating*
|
Lot Size Factor
|
---|
Well suited
|
0.30
|
Moderate or slow
|
0.50
|
Severe
|
0.70
|
*
|
Refer to map maintained in Community Development Department.
|
Percolation tests may be substituted for the Natural
Resources Conservation Service reports. These shall be prepared by
a registered civil engineer or licensed sanitarian. The following
conversion chart shall be used to determine the appropriate lot size
factor:
Percolation Rating
|
Minutes Per Inch
|
---|
Well suited
|
Less than 20
|
Moderate
|
20 to 39
|
Slow
|
40 to 59
|
Severe
|
Greater than 60
|
(3) Average Slope. Using the basic, sectional or contour measurement
method, the lot size factor based on this performance standard shall
be:
Slope
|
Lot Size Factor
|
---|
0—20%
|
0.30
|
21—30%
|
0.50
|
31%+
|
0.70
|
(4) Condition of Access. Using the road right-of-way with the shortest
accessible distance between a lot and an improved collector road,
the lot size factor based on this performance standard shall be:
Condition
|
Lot Size Factor
|
---|
Paved with slope of less than 15% or City-accepted
|
0.15
|
Paved with slope of greater than 15%
|
0.20
|
All-weather surface with slope of less than 15%
|
0.25
|
All-weather surface with slope of greater than 15%
|
0.30
|
Unimproved surface
|
0.40
|
(5) General Neighborhood Character. Using the average lot size of existing
lots (except that lots larger than five acres shall be excluded unless
they constitute more than 25% of the total number of lots) within
a 1,000 foot radius, the minimum lot size factor based on this performance
standard shall be determined by multiplying the average lot size by
0.2.
(b) Determination of Minimum Lot Size. The minimum lot size shall be determined by the sum of each of the lot size factors for the performance standards set forth in subsection
(a) of this section.
(1) The most current information shall be used to determine the lot size
factor. Where information is not available, the Planning Director
shall determine which lot size factor shall apply.
(2) If more than one lot size factor can be applied to a lot, the less
restrictive factor shall be used.
(3) Lot size factors shall be based on conditions in existence at the
time of filing an application unless information is included with
the application which will alter a lot size factor.
(Ord. 602 § 2, 2016; Ord. 614 § 4, 2017)
The minimum lot size in the Limited Residential Single-Family Zone shall be 20,000 square feet with sewer, 1/2 acre where sewer is not available and may range up to two and one-half (2-1/2) acres. The size of a lot shall be consistent with the land use designation set forth in the General Plan and shall be indicated by the symbols set forth in the following chart, which shall be shown on the official zoning maps as provided by Section
9-3.104(d).
Symbol
|
Minimum Lot Size
|
---|
X
|
1/2 acre net area (excluding land needed for street rights-of-way
whether publicly or privately owned).
|
Y
|
1 acre, when sewers are available. 1-1/2 acres, when sewers
are not available.
|
Z
|
1-1/2 to 2-1/2 acres based on performance standards set forth
in this section.
|
(a) Performance
Standards. The following performance standards shall be evaluated
for each lot which is appended with the "Z" symbol in determining
its minimum lot size:
(1) Distance from the Center of the Community. Using the Atascadero Administration
Building as the center of the community, the lot size factor based
on this performance standard shall be:
Distance*
|
Lot Size Factor
|
---|
0—4,000′
|
0.08
|
4,000′—6,000′
|
0.10
|
6,000′—8,000′
|
0.12
|
*
|
To be measured as radial distance using map maintained in the
Planning Department.
|
(2) Septic Suitability. Using generalized soils data from the Natural
Resources Conservation Service Reports, the lot size factor based
on this performance standard shall be:
NRCS Rating*
|
Lot Size Factor
|
---|
Well suited
|
0.30
|
Moderate or slow
|
0.50
|
Severe
|
0.70
|
*
|
Refer to map maintained in Community Development Department.
|
Percolation tests may be substituted for the Natural
Resources Conservation Service Reports. These shall be prepared by
a registered civil engineer or licensed sanitarian. The following
conversion chart shall be used to determine the appropriate lot size
factor:
Percolation Rating
|
Minutes Per Inch
|
---|
Well suited
|
Less than 20
|
Moderate
|
20 to 39
|
Slow
|
40 to 59
|
Severe
|
Greater than 60
|
(3) Average Slope. Using the Basic, Sectional or Contour Measurement
Method, the lot size factor based on this performance standard shall
be:
Slope
|
Lot Size Factor
|
---|
0—20%
|
0.30
|
21—30%
|
0.50
|
31%+
|
0.70
|
(4) Condition of Access. Using the road right-of-way with the shortest
accessible distance between a lot and an improved collector road,
the lot size factor based on this performance standard shall be:
Condition
|
Lot Size Factor
|
---|
Paved with slope of less than 15% or City-accepted
|
0.15
|
Paved with slope of greater than 15%
|
0.20
|
All-weather surface with slope of less than 15%
|
0.25
|
All-weather surface with slope of greater than 15%
|
0.30
|
Unimproved surface
|
0.40
|
(5) General Neighborhood Character. Using the average lot size of existing
lots (except that lots larger than five acres shall be excluded unless
they constitute more than 25% of the total number of lots) within
a 1,000 foot radius, the minimum lot size factor based on this performance
standard shall be determined by multiplying the average lot size by
0.2.
(b) Determination of Minimum Lot Size. The minimum lot size shall be determined by the sum of each of the lot size factors for the performance standards set forth in subsection
(a) of this section.
(1) The most current information shall be used to determine the lot size
factor. Where information is not available, the Planning Director
shall determine which lot size factor shall apply.
(2) If more than one lot size factor can be applied to a lot, the less
restrictive factor shall be used.
(3) Lot size factors shall be based on conditions in existence at the
time of filing an application unless information is included with
the application which will alter a lot size factor.
(Ord. 602 § 2, 2016; Ord. 614 § 4, 2017)
The minimum lot size in the Residential Multiple-Family Zone shall be 1/2 acre. Smaller lot sizes may be allowed for planned residential developments, including condominiums and mobilehome developments, provided that the overall density within the project conforms with Section
9-3.252.
(Ord. 602 § 2, 2016)
New residential subdivisions and the density of residential development shall comply with the requirements of Sections
9-3.251 through 9-3.259.
(Ord. 602 § 2, 2016)
New residential subdivisions and the density of residential
development shall comply with the following for single-family residential
zones:
(a) A
(Agriculture). A maximum of one single-family residence. Additional
housing for agriculture employees may be permitted, consistent with
this Municipal Code.
(b) RS
(Residential Suburban). A maximum of 0.1 to 0.4 units per gross acre.
A second unit may be permitted consistent with Chapter 9-5 of this
Zoning Ordinance.
(c) RSF-Z/LSF-Z.
A maximum of one unit per gross acre. A second unit may be permitted
consistent with Chapter 9-5 of this Zoning Ordinance.
(d) RSF-Y/LSF-Y.
A maximum of one unit per gross one-half acre. A second unit may be
permitted consistent with Chapter 9-5 of this Zoning Ordinance.
(e) RSF-X/LSF-X.
A maximum of four residential units per net acre, with approval of
a Planned Development. Overlay zones with innovative design concepts,
as approved by the City Council. A second unit may permitted consistent
with Chapter 9-5 of this Zoning Ordinance.
(Ord. 602 § 2, 2016)
The maximum allowable density in the Residential Multiple-Family Zone shall be designated on the official zoning maps as provided by Section
9-3.104(c) and be consistent with the General Plan for new residential subdivisions as follows:
(a) Areas
Designated Low Density Multiple-Family Residential. The minimum number
of dwelling units per net acre is two. The maximum number of dwelling
units per net acre is 10.
(b) Areas
Designated High Density Multiple-Family Residential. The minimum number
of dwelling units per net acre is 20. The maximum number of dwelling
units per net acre is 24.
(c) Hillside Density Standards. The densities permitted by subsections
(a) and
(b) of this section shall be modified to the following densities based on site topography, as follows:
Average Slope
|
Low Density Multiple-Family (units/acre)
|
High Density Multiple-Family
(units/acre)
|
---|
Minimum
|
Maximum
|
---|
0—10.99%
|
10
|
20
|
24
|
11—15.99%
|
7
|
14
|
17
|
16—20.99%
|
5
|
10
|
12
|
21—25.99%
|
3
|
6
|
7
|
26—30.0%
|
2
|
4
|
5
|
> 30%
|
1
|
2
|
2
|
(d) For
medical extended care services, where residents are primarily nonambulatory,
the following maximum bed/net acre densities may be permitted, where
subject to Planning Commission conditional use permit approval:
RMF-10 District
|
34 beds/net acre
|
RMF-24 District
|
55 beds/net acre
|
Such approval shall require a finding that the average daily traffic generated by the project would not exceed that of a multifamily project. The project would be further subject to the "percentage coverage" constraints of subsection
(a) of the district. Off-street parking requirements would be as established by the Planning Commission.
(e) Sewer
Service. Sewer service and the inclusion of property within the urban
services line (USL) shall be a prerequisite to developing multiple-family
projects to the density standards of the RMF zone.
(f) Density Bonus. A density bonus may be granted, subject to approval by the City Council through a master plan of development (CUP), consistent with Sections
9-3.801 through
9-3.806.
(g) In
lieu of granting a density bonus, the Planning Commission shall consider
other bonus incentives allowable under
Government Code Section 65915.
(Ord. 602 § 2, 2016; Ord. 614 § 4, 2017)
New land uses, structures, and alterations to existing land
uses and structures shall be designed, constructed and established
in compliance with the Sections 9-3.261 through 9-2.269, in addition
to applicable standards (e.g., landscaping, parking, fencing, etc.)
in Chapter 9-4 of this title.
(Ord. 602 § 2, 2016)
In addition to the standards specified in Chapter 4 of this
title, General Site Design and Development Standards, the following
development standards shall apply to mobile home and multiple-family
residential projects:
(a) Percent
Coverage. The maximum percent of a lot that may be covered by structures
(excluding decks less than 30 inches from the ground) shall be 40%
for low density multiple-family projects and 50% for high density
multiple-family projects.
(b) Enclosed
Storage. Each dwelling unit shall be provided a minimum of 100 cubic
feet of enclosed storage space, exclusive of closets, which may be
located in either a principal or accessory building.
(c) Outdoor
Recreation Areas. For developments of four to seven dwelling units,
outdoor recreational open space shall be provided at a ratio of 300
square feet per unit. This open space may be provided either as: (1)
a private amenity designed for exclusive use of a dwelling unit; or
(2) as common open space provided that no individual open space is
less than 1,000 square feet. For developments of eight or more dwelling
units, outdoor recreational open space shall be provided at a ratio
of 300 square feet per unit. This common open space may be provided
in more than one location provided that no individual open space area
is less than 1,000 square feet.
(d) Screening
Wall. A solid wall or fence not less than six feet in height shall
be placed and maintained on interior lot lines abutting property zoned
for single-family residential use.
(e) Laundry
Facilities. Laundry facilities shall be provided in the form of either:
(1) laundry hook-ups within each individual dwelling unit; or (2)
a shared laundry facility equipped with washers and dryers.
(f) Appearance
Review. All projects shall be consistent with the multifamily design
and landscape requirements of the Appearance Review Manual.
(g) Maintenance
Requirement. A maintenance agreement for all landscaping, building
exteriors, accessory structures, parking areas and other common facilities
shall be approved by the Community Development Director and City Attorney
prior to final occupancy.
(h) RMF-24
properties identified in Appendix 1, Table V-45 (Vacant Residential
Parcels RMF-20), of the General Plan Housing Element shall be permitted
"by right" and will not be subject to conditional use permit or specific
plan. Proposed planned development projects or other relief from property
development standards on these parcels shall be subject to discretionary
review per the requirements of the municipal code.
(Ord. 602 § 2, 2016; Ord. 614 § 4, 2017; Ord. 646 § 11, 2021)