The final plat of the subdivision shall comply with the following requirements and contain the following information.
A. 
Drawing. The final plat shall be legibly and accurately drawn on tracing linen or Mylar sheets 18 inches by 24 inches in size, and at a scale of one inch to 50 feet, or one inch to 100 feet, depending upon the size and nature of the subdivision. If more space is needed, additional sheets may be used. Drawings must have a three-and-one-half-inch margin on the left side and a one-half-inch margin on the other sides. Each additional sheet on a final plat shall contain all of the necessary information so as to stand on its own.
B. 
Meet platting requirements. The final plat shall conform in all respects to the requirements of Real Property Article, § 3-108, Annotated Code of Maryland, as amended, which relates to the making, filing, and recording of plats. Among other things, the article above requires that plats for recording must be surveyed and certified by a registered-surveyor.
[Amended 10-9-2018 by Ord. No. 2018-08]
C. 
Title information.
(1) 
Subdivision name.
(2) 
Location by election district, town or county and state.
(3) 
Names and addresses of the owners of record, the subdivider, and the engineer or surveyor.
(4) 
Scale.
[Amended 10-9-2018 by Ord. No. 2018-08]
(5) 
North point.
[Amended 10-9-2018 by Ord. No. 2018-08]
(6) 
Date.
[Amended 10-9-2018 by Ord. No. 2018-08]
(7) 
A map showing location in county (one inch = 1,200 feet).
The following graphic information shall be provided:
A. 
Boundaries: exact boundaries of the area included within the subdivision, with dimensions to hundredths of a foot and bearing to half minutes. These boundaries shall be determined by an accurate survey in the field in accordance with minimum standards for practice for boundary surveys as defined in 09.13.03.00, Title 9 Department of Labor, Licensing, and Regulation Subtitle 13 Board for Professional Land Surveyors Chapter 3 Survey Markers Authority: Business Occupations and Professions Article, § 15-208, Annotated Code of Maryland. Coordinates must be shown at all boundary break points.
[Amended 10-9-2018 by Ord. No. 2018-08]
B. 
Bearings and distances: bearings and distances to the nearest recorded property corners or other monuments, which shall be located or accurately described on the plat.
C. 
Monuments: the accurate location and descriptions of all permanent monuments. Where applicable and feasible the coordinates of all permanent markers or monuments should be based on the Maryland Coordinate System.
[Amended 10-9-2018 by Ord. No. 2018-08]
D. 
Adjoining owners: names and locations of adjoining subdivisions and the locations and ownership of adjoining unsubdivided property.
E. 
Adjoining roads: exact locations, width, and name of each existing or recorded road or street adjoining or intersecting the boundaries of the tract.
F. 
Engineering data: the exact location and width of every road, street, alley, easement, or other public or private way within the tract, with the length and bearing of every tangent, length of arcs, radii, delta angle, tangent, chord length, chord bearings and any other necessary engineering data; with the names of such ways, and the purpose of easements or other ways; accurate location of every lot line, with its dimension to hundredths of a foot and bearings to half-minutes, except that this data need not be repeated on a series of parallel lines or lines of the same length.
G. 
Setback lines: minimum building setback lines (front, side, rear) on all lots and other sites.
H. 
Numbering: blocks lettered in alphabetical order, and lots numbered in numerical order.
I. 
Public lands: accurate outlines or any areas dedicated or reserved for public use, or for any other purpose except sale, with the purpose indicated.
J. 
Lot area: accurate area of each lot or parcel, other than public ways.
K. 
Municipal lines: accurate location of any municipal or district line traversing or closely related to the tract.
L. 
Drainage lines: existing and relocated courses of any watercourses or storm drainage facilities traversing the tract, with the right-of-way or easement lines provided therefor.
M. 
Water and sewer lines: the location and size of all existing and proposed water and sewer lines.
The following certificates and other information shall be provided:
A. 
Owner's certificate: owner's certificate, signed and notarized, acknowledging ownership of the property and agreeing to the subdividing thereof as shown on the plat; also offering for dedication all streets and other ways and places intended for public use.
B. 
Surveyor's certificate: certificate of the surveyor to the effect that the plat represents a survey made by him, that it is accurate to the best of his knowledge, and that all survey markers indicated thereon actually exist and their locations and descriptions are correctly shown, and that all requirements of this chapter and of other applicable laws have been fully complied with.
[Amended 10-9-2018 by Ord. No. 2018-08]
C. 
Agency approvals. A space shall be provided for a certificate of approval by Myersville Planning Commission. The plat must also contain a space for approval of the Frederick County Health Department with the required Health Department statement on conformance with the County Master Water and Sewer Plan and a statement signed by the owner that all lots offered for sale will be serviced by public water and public sewerage.
[Amended 10-9-2018 by Ord. No. 2018-08]
D. 
Protective covenants. Protective covenants which apply to all the area as shown by the recorded plat shall be part of the recorded plat.