[HISTORY: Adopted by the Town Board of the
Town of Cornwall 2-12-1990 by L.L. No. 3-1990. Amendments noted where
applicable.]
GENERAL REFERENCES
Streets and sidewalks — See Ch.
122.
Subdivision of land — See Ch.
125.
Vehicles and traffic — See Ch.
143.
A. The Town Board of the Town of Cornwall has determined
that the existing street specifications are outdated in light of the
current accepted construction standards and the need to provide better
roads for the Cornwall community. To that end, the Town Board has
caused this local law to be prepared in an effort to upgrade the requirements
for the construction of roads within the Town of Cornwall. The local
law recognizes the need for greater engineering involvement in the
design and construction of roads, the need for flexibility in performance
and maintenance security and the importance of clear and updated cross
section details, catch basin details and sidewalk and curb details.
B. In furtherance of the proposed local law, the Town Board does hereby repeal existing Chapter
A161 of the Code entitled "Street Specifications for Town Roads" and does hereby designate the Chapter
A161 as set forth in this local law to be known as "Road Specifications for Town Roads."
A. It is the purpose of these specifications to establish
minimum acceptable standards for roads and road construction within
the Town of Cornwall to conform to legal requirements in the State
of New York, which requirements and standards must be met and paid
for by the offeror proposing that the Town take over such road as
a Town road. Herein, wherever reference is made to the term "offeror,"
the same shall be understood to mean the person, persons, developer,
firm or other entity proposing that the Town take over such road as
a Town road. These specifications include but are not limited to width,
design, drainage, construction of base and pavement, curbs, sidewalks
and monuments.
B. Dedication of the right-of-way will not be accepted
until the offeror's professional engineer and/or licensed land surveyor
shall have certified to the Town Board, in writing, that the construction
of the road has been completed in accordance with the approved plans
and specifications that follow and that the total right-of-way area
has been cleared of all debris and all construction has been completed
in a workmanlike manner; and the Town Superintendent for Public Works
and the Town Engineer shall have reviewed the completed work and recommended
acceptance of such dedication. When new road rights-of-way are offered
to the Town for dedication, four copies of the final as-built plan
and deed description of the right-of-way shall be submitted to the
Town Superintendent of Public Works for approval.
C. In his written certification as required above, the
offeror's professional engineer or qualified licensed land surveyor
shall state clearly that he or his authorized representative has inspected
all phases of the road construction and that all work has been completed
in accordance with the approved plans and these specifications.
A. A plan of the proposed road shall be prepared by a
qualified professional engineer and/or qualified land surveyor, licensed
by the State of New York for such design functions. The plan shall
clearly define the limits of the proposed right-of-way by metes and
bounds and shall include the location, widths, profiles and grades
of the proposed roadway, storm drainage, including culverts, and other
drainage structures and the location of all easements and utilities.
B. The plan shall also indicate the owner of the property
and the name of the developer, if other than the owner. One copy each
of the plan shall be submitted to the Town Superintendent of Public
Works and the Town Engineer at the time of application to make such
road a Town road and to the County Commissioner of Public Works or
his designated representative when said proposed street drains toward,
intersects with or may otherwise affect a county highway. If applicable,
it will concurrently be submitted to the Town Planning Board for review
and approval under the applicable subdivision regulations of the Town. Such roadway must not be subject to any right or easement
in others which will in any way interfere with its use as a road at
all times. Such road must be conveyed to the Town by a deed in recordable
form acceptable to the Town Attorney, containing a metes and bounds
description, together with recording fees payable to the Orange County
Clerk accompanied by such evidence of title indicating that title
is vested in the Town free and clear of any liens and encumbrances,
including, where required, a policy of title insurance.
C. Permanent and temporary easements must be furnished
in said deed granting to the Town the right to maintain all outlets
for surface water or natural stream drainage which will run from such
roadway over private property to a point where a natural watercourse
exists and to which such outlet and easement will carry such water.
A minimum width of 20 feet of easement shall be required for the maintenance
of said easements.
D. The proposed roadway must be constructed to conform
to the minimum requirements and standards set forth below. The minimum
width to be cleared shall include all trees, rock formations, buildings,
walls and any such things that would endanger those using such roadway.
The removal of such obstructions shall be borne by the offeror proposing
such road.
E. In general, all materials and methods of construction
required for construction of Town roads shall be in accordance with
the Standard Specifications, Construction and Materials, published
by the New York State Department of Transportation (NYSDOT), Design
and Construction Division, latest revision.
This local law repeals existing Chapter
A161 of the Code of the Town of Cornwall.
Plans submitted shall not be altered or amended
after having been approved by the Town Superintendent of Public Works
and the Town Engineer unless amended plans are resubmitted and approved.
However, the offeror, at his own expense, shall provide additional
storm drainage facilities, utilities and/or other miscellaneous work
as may be ordered by the Town Superintendent of Public Works and the
Town Engineer if, during the course of construction, in the opinion
of the Town Superintendent of Public Works, the Town Engineer and/or
the County Commissioner of Public Works, such additional structures
or facilities are necessary to prevent any need for future installations
of utilities or culverts within the pavement area and to assure the
durability of pavement, future maintenance of the right-of-way or
welfare and safety of the public.
A. Performance security. Unless the offeror shall construct
the entire road and related improvements in accordance with this local
law before offering the same to the Town, prior to the start of construction
of any road or at the time designated in the subdivision regulations,
if applicable, the offeror shall post performance security with the Town
either in the form of a bond of an acceptable surety, an irrevocable
letter of credit, negotiable government bonds, cash or bank or certified
funds drawn on a national or state bank to guarantee construction
of the improvements in compliance with the approved plans and these
specifications. The form of the performance security shall be reviewed
and approved by the Town Attorney. Where such proposed road is subject
to the subdivision regulations of the Town, procedures for posting
the performance security shall also comply with those regulations.
The amount of the performance security shall be based on current municipal
construction costs and shall be reviewed and approved by the Town
Engineer and approved by the Town Board.
B. Maintenance security. The offeror shall post maintenance security
with the Town in the form of either an irrevocable letter of credit,
cash or bank or certified funds drawn on a national or state bank
to guarantee that for a period of one year from the date of acceptance
of the dedication of the road by the Town Board, the developer will
maintain the road to the standard of construction set by these specifications,
normal wear and tear excepted. This shall mean that the offeror will,
at its own expense, repair and make good any defects or damage which
may develop during this maintenance period as a result of faulty construction
within the right-of-way or as a result of other construction, by the
offeror or others, outside the right-of-way. During the maintenance
period, the Town shall be responsible for snow and ice control, street
cleaning, cleaning of culverts and catch basins and other work of
similar routine nature, provided that such work has in no way been
caused by the operations of others. The amount of the maintenance
security shall be determined by the Town Engineer and shall be equal
to 10% of the original amount of the performance security. The provisions
of the local law concerning review and acceptance of the form of the
performance security shall be applicable to the form of the maintenance
security.
[Amended 1-9-2017 by L.L.
No. 1-2017]
C. Inspection fees. Upon the completion of the design
for the Town road and determination of the amount of the performance
security as set forth above, the offeror shall pay to the Town an
inspection fee in the amount of 4% of the performance security. Road
construction shall not commence until the four-percent inspection
fee has been paid. The inspection fee must be paid whether or not
the offeror elects to construct the road without the posting of performance
security; in that event, the inspection fee shall be placed upon 4%
of what the performance security would have been had the offeror availed
itself of the option of posting performance security.
A. Subdivision roads.
(1) For roads in subdivisions, the Town Superintendent
of Public Works and the Town Engineer shall, pursuant to a recommendation
by the Town Planning Board, determine and designate into which of
the three following classifications each proposed road falls on the
basis of one or more of the criteria hereinafter set forth. For all
other roads, the Town Superintendent of Public Works and the Town
Engineer shall make this determination.
(2) Final plans shall be drawn to show and the offeror
shall construct each road in accordance with the particular specifications
for its designated classification as hereinafter set forth, as well
as in accordance with the specifications common to all classifications.
(3) Determining criteria.
(a)
Major road: a road which serves or is designed
to be used primarily as a route for traffic between communities or
large areas.
(b)
Secondary road: a road which serves or is designed
to carry traffic from local residential roads to the system of major
roads.
(c)
Minor road: a road intended to serve primarily
as access to abutting residential properties.
B. Construction specifications.
(1) Figures 1, 2, 3 and 4 annexed to this local law show
the cross sections of each of the classifications for Town roads.
Figures 5, 6 and 7 annexed to this local law show typical details
for construction of Town roads. These give the minimum required design, dimensions and
construction details which are applicable to each classification.
(2) The general and more detailed specifications follow
for design, construction, materials and other requirements which are
applicable to all classifications of roads.
(3) The offeror shall design and construct roads which
shall conform to both the general and specific specifications.
|
NOTE: The subbase and foundation course shall
lay a minimum of three months to allow complete settlement before
pavement is laid.
|
C. Alternate minor road.
(1) Where approved by resolution of the Town Board, subsequent
to the recommendations of the Town Planning Board, the Superintendent
of Public Works and the Town Engineer, construction of a Town road
without curbs, in accordance with the Alternate Minor Street Detail
(Figure 4), will be permitted. Where required by the Town Board, such
alternate minor road shall be provided with concrete sidewalks.
(2) Requests for construction of alternate minor roads
shall be made in writing to the Town Board.
A. The offeror shall establish and clearly mark on site
the limits of road rights-of-way and easements with permanent monuments
on the center line and grades of the finished road pavement and the
location and elevations of drainage structures as shown on the approved
plans with construction stakes. Such construction stakes shall be
maintained at the offeror's expense until the construction of road
pavement, drainage structures, underground utilities, curbs, sidewalks
and shoulders has been completed, inspected and approved by the Town
Superintendent of Public Works and the Town Engineer.
B. During the course of construction, the developer shall
provide the Town Engineer with stakeout information, cut sheets or
any other pertinent information requested with respect to the proposed
construction.
C. Permanent monuments shall be set on right-of-way lines
of roads at all intersections, angle points, point of curvature and
the beginnings and ends of streets. There shall be a clear view of
adjacent monuments on the right-of-way line. All monuments shall exist
on completion of the construction of the roads.
D. The permanent markers shall be made of concrete or
granite with minimum dimensions of 30 inches long, a four-inch square
top and a six-inch square bottom with a one-half-inch drilled hole
in the top. As an alternate, 3/4 inches in diameter steel rods, with
a welded copper coating and bronze tops, 30 inches long, may be used
as monuments. If a monument should be located in a rock ledge, the
surface shall be stripped and a one-half-inch steel rod drilled into
the ledge to a depth of six inches. Monuments shall protrude a maximum
of two inches above the final graded surface. The offeror's licensed
surveyor shall certify that the location of all monuments is accurate
before acceptance of the road by the Town Board. A certified reproducible
map showing the locations and reference ties to each monument shall
be provided. Reference ties shall be permanent items, such as building
foundations, and a minimum of three shall be provided for each monument.
Where surface water from roads must lead through
other than gutters and storm drains or existing stream channels outside
the right-of-way, permanent drainage easements having a minimum width
of 20 feet shall be provided to a point where a natural watercourse
exists. In some cases this may include easements over property outside
the boundaries of the subdivision involved. Natural stream or ditch
channels shall have a minimum of twenty-foot-wide permanent easements
and be shown on the proposed plans of the subdivision. All permanent
easement lines shall be monumented as a right-of-way.
A. The offeror shall clear and grub the entire area within
the limits of the road right-of-way, drainage channels and easement
areas where required by the Town Superintendent of Public Works and
the Town Engineer. The offeror shall properly dispose of all waste
materials (stumps, roots, etc.) off site.
B. The offeror shall complete the shaping of the road
right-of-way, streams and ditches and easement areas to the line and
grade as shown on the approved plans and as otherwise may be required
by the Town Superintendent of Public Works and the Town Engineer.
In the construction of the roadway, all topsoil, loam, rocks and organic
material shall be removed until a satisfactory subbase is established.
In fills of less than three feet, all topsoil shall be excavated and
removed. All fills under roadways shall be made with foundation course
material meeting or exceeding the requirements of Gradation Type No.
3 subbase material as specified under Section 3 of the New York State
Department of Transportation Standard Specifications-Construction
and Materials (latest revision), or other acceptable material as approved
by the Town Superintendent of Public Works and the Town Engineer.
Such fills shall be made in layers of not more than 12 inches each
and properly compacted with a ten-ton roller or equivalent.
C. All hollows and depressions which develop under rolling
shall be filled with acceptable granular material and again rolled,
this process to be continued until no depressions develop. The subgrade
shall not be muddy or otherwise unsatisfactory when the foundation
course is laid upon it. Any soft spot or unstable portion of the subgrade
which develops under the roller shall be completely excavated and
removed from the right-of-way and shall be replaced with acceptable
granular material and the area regraded and compacted as above.
D. If, in the opinion of the Town Superintendent of Public Works and the Town Engineer, it is prudent that stabilization fabrics be installed under the Town road in those areas observed as unstable or soft or in other areas deemed appropriate by the Superintendent and the Engineer, the offeror, at his own expense, shall provide such fabric for those areas and for the length of roadway as determined by the Town Superintendent of Public Works and the Town Engineer. Stabilization fabric shall meet the requirements as called for under §
A161-17 of these specifications.
E. The subgrade shall be shaped to line and grade with
no depressions. The subgrade shall be stable in all respects to the
satisfaction of the Town Superintendent of Public Works and the Town
Engineer before the foundation course is laid. No large stones or
rock ledges shall protrude into the foundation course.
F. Should it become necessary, as part of the construction
work, to perform blasting, the same shall only be done following notification
to the Town Superintendent of Public Works and the Town Engineer.
The Town shall assume no responsibility or liability pertaining to
any blasting work. Prior to any blasting, the contractor shall submit
an insurance certificate for the type work, in an amount no less than
$1,000,000, for the work to be performed. All work shall be done taking
all possible precautions and shall, at minimum, comply with all applicable
federal, state and local regulations. Blasts shall be covered with
suitable mats or heavy timber, at minimum, to prevent damage. Blasting
shall only be performed between 8:00 a.m. and 5:00 p.m. on weekdays
unless otherwise approved. Blasting shall not be performed on legal
holidays.
G. Also, before the foundation course is laid, all storm
and sanitary sewers and all utilities, including house connections
for existing and future homes, and hydrants shall have been installed
to the satisfaction of the Town Superintendent of Public Works, the
Town Engineer and the Water Superintendent. All slopes and sidewalk
areas shall be graded before the foundation course is made, and all
loose and exposed stones will be removed. Fine grade shall conform
to the prescribed width of pavement and shall extend equidistant from
the center line of the road right-of-way and shall conform to the
typical cross section of the road pavement and to the approved line
and grade.
A. General requirements.
(1)
The drainage system and/or culverts shall be
designed in accordance with established engineering principles and
approved by the Town Superintendent of Public Works and the Town Engineer.
Standards for design of the system shall be based on the drainage
area tributary to the proposed system and structures, as follows:
|
Drainage Area
(acres)
|
Design Occurrence
|
---|
|
Less than 320
|
25-year storm
|
|
320 to 640
|
50-year storm
|
|
Greater than 640
|
100-year storm
|
(2)
Plans for any drainage structure, including
pipe culverts, when existing or proposed, shall be submitted in detail
by the offeror's professional engineer to the Town Superintendent
of Public Works and the Town Engineer for approval. The submittal
shall include calculations and a drainage area evaluation map, bearing
the seal and signature of the offeror's professional engineer.
(3)
The minimum grade of any drainage pipe or culvert
shall not be less than 1%. The approved plans shall show invert elevations
of all inlets and outlets for all drainage structures. All pipes shall
be provided with a minimum eighteen-inch cover unless otherwise approved.
Any deviation from the approved plans shall be on approval of the
Town Superintendent of Public Works and the Town Engineer, in writing.
No culvert pipe shall be less than 18 inches in diameter unless by
approval of the Town Superintendent of Public Works and the Town Engineer.
Pipe for culverts may be reinforced concrete or corrugated metal pipe,
both of which shall conform to the following specifications for materials.
(4)
Prior to the delivery of any materials or the
construction of any work, the offeror shall submit to the Town Engineer
four copies of manufacturer's detailed literature for all materials
proposed to be used. No materials shall be delivered or placed until
the proposed materials have been accepted.
B. Reinforced concrete pipe. All concrete pipe utilized
in the work shall be reinforced and shall conform to the requirements
referenced in the New York State Department of Transportation Standard
Specifications - Construction and Materials (latest edition), as stated
in Section 706, except that the tongue and groove pipe is preferred
for all sizes. Each piece of pipe shall be stamped as such and the
conditions of pipe shall be approved by the Town Superintendent of
Public Works and the Town Engineer. Rejected specimens will be immediately
removed from the site.
C. Corrugated metal pipe.
(1)
All corrugated metal pipe shall conform to the
requirements referenced in the New York State Department of Transportation
Standard Specifications - Construction and Materials (latest edition),
as stated in Section 707.
(2)
Corrugated metal pipe shall conform to the requirements
of AASHO Designations M190 and M36. All pipe shall be fully bituminous
coated with paved invert. The gauge of the pipe shall be in accordance
with the New York State Standard Specifications for Corrugated Metal
Pipe for the intended use, and in all cases shall be a minimum of
16-gauge.
D. Alternate materials. Where approved by the Superintendent
of Public Works and the Town Engineer, in writing, use of alternate
materials will be considered. Decision for the use of such alternate
materials shall be based on the specific cases of the installation,
as interpreted by the Superintendent and the Town Engineer.
E. Installation.
(1)
The width of the trench in which the pipe is
laid shall be sufficient to permit thorough tamping of the backfill
around the pipe. A cushion of at least six inches of run-of-bank (ROB)
gravel shall be laid in line with grade prior to laying the pipe.
No stones over three inches maximum dimension shall protrude or lay
in this cushion. The soil below the cushion shall be stable enough
that there will be no settlement of pipe after backfilling the trench.
(2)
The pipe shall be laid to true line and grade
on the prepared bed of the trench. All connections for corrugated
metal pipe shall consist of twelve-inch corrugated metal bands lapping
on equal portions of the sections to be connected. Backfilling of
the trench shall be done with run-of-bank gravel or other suitable
material approved by the Town Superintendent of Public Works and the
Town Engineer. The backfill shall be made in layers of no more than
12 inches, which shall be tamped or watered.
(3)
All drainage pipes and structures shall be of a size sufficient to carry natural water runoff and stormwater and also which, in the opinion of the Town Superintendent of Public Works and the Town Engineer, are acceptable based on the design criteria in Subsection
A of this section and which may be reasonably anticipated from future construction, both from within the development and from adjoining properties which normally drain across the area of the proposed development. Additional or larger culvert pipes and drainage structures shall be installed and paid for by the offeror, if in the opinion of the Town Superintendent of Public Works and Town Engineer, the same is deemed appropriate and in the best interest of the Town.
F. Groundwater. If, in the opinion of the Town Superintendent
of Public Works and the Town Engineer, it is necessary to intercept
and carry away groundwater within the limits of the right-of-way to
protect the stability of the road bed, curb or sidewalk areas, such
subdrainage shall be required and shall be installed by the offeror.
Porous wall concrete pipe or perforated PVC pipe having a minimum
diameter of four inches, encased in 12 inches of three-fourths-inch
clean crushed stone or crushed gravel, shall be used for such purpose
for a length as deemed necessary by the Town Superintendent of Public
Works and the Town Engineer.
G. Catch basins and curb inlets.
(1)
Catch basins and curb inlets shall be constructed in order that surface water be intercepted. All catch basins shall be precast reinforced concrete, spaced as noted hereinbelow, unless otherwise approved by the Superintendent of Public Works and the Town Engineer. Concrete shall meet the requirements as called for in §
A161-19 of this specification. Such structures shall be placed at 400 feet or less. On grades in excess of 6%, the distance apart shall not exceed 250 feet. Figures 5 and 6 outline the minimum details of construction for catch basins and curb inlets. Whenever, in the opinion of the Town Superintendent of
Public Works and the Town Engineer, ground conditions or other circumstances
require it, larger or heavier materials, additional materials, reinforcing
or other modifications and improvements in design and construction
shall be made as required by the Town Superintendent and the Town
Engineer at any time prior to construction of pavement.
(2)
For purposes of standardization and proper,
timely and safe replacement, the following curb inlet casting shall
be considered standard for supply on Cornwall Town roads:
(a)
Curbed roadways: Campbell No. 2633.
(b)
Noncurbed roadways:
[1]
Campbell No. 3490 (gutter type).
[2]
Campbell No. 3087 (straight type).
(3)
Substitution of or-equal castings shall be only
when approved, in writing, by the Town Superintendent of Public Works.
H. Headwalls.
(1)
Headwalls of reinforced concrete shall be constructed at the outlet and inlet ends of culvert pipes. Culverts shall extend to the toe of embankment. Concrete shall conform to the minimum requirements noted in §
A161-19 of this specification. The bearing of all headwalls shall have a solid base. If soft material is encountered, it shall be removed and backfilled with acceptable fill material as specified under §
A161-10 of this specification. It shall be the responsibility of the offeror that no headwalls shall crack or become tipped from settlement.
(2)
Prior to construction, the offeror's professional
engineer shall submit to the Town Engineer details of construction
for the proposed headwall specific for the proposed installation.
I. House drains. Roof and cellar drains shall in no case
be allowed to flow into the road right-of-way. With the approval of
the Town Superintendent of Public Works and the Town Engineer, in
writing, these drains may be piped to existing stormwater pipe drains,
if any, to which they will be connected on top only. Such drains must
be installed prior to the start of the application of the foundation
course. Drains from sanitary sewers or septic tanks will not be permitted
to flow into road ditches or storm drains under any circumstances.
A. Grades and vertical curves. The grade of major and secondary roads shall not be in excess of 12% nor less than 1%. The grade of minor roads shall not be in excess of 14% nor less than 1%. Only by permission of the Town Superintendent of Public Works, pursuant to the recommendation of the Town Engineer and the Planning Board, if applicable, shall a grade of more than 10% be allowed on any road, due to topographic conditions. Differences in grade will be effected with a vertical curve of sufficient length to allow a vertical sight distance in compliance with Subsection
B of this section, but in no case less than 250 feet. The maximum grade of intersecting roads shall not exceed 2% for a distance of 50 feet from the intersection.
B. Sight distance.
(1)
In all cases, design of intersections shall
always maximize sight distance and comply with the minimum recommended
safe sight distances as referenced in the Institute of Traffic Engineers
(ITE) Guidelines for Driveway Design and Location (latest revision),
and as referenced in the New York State Department of Transportation
Policies and Standards. When such minimum recommended safe sight distances
cannot be obtained due to specific site conditions, the offeror's
professional engineer shall submit sufficient documentation to show
the maximum available and the specific reasons why the recommended
values cannot be obtained. For roads proposed in subdivisions, such
information shall also be submitted to the Planning Board, and the
road location shall be subject to its approval.
(2)
"Sight distance" shall be defined as the distance
where an object remains visible to an observer, said observer (driver)
waiting to enter from an intersecting road or driveway at a point
12 feet in advance of the nearest travel lane, which measurement shall
be taken from a level of 44 inches above the road/driveway pavement,
observing a vehicle at a point 24 inches above the pavement at the
point being observed. A similar method shall be utilized in the determination
of stopping sight distance and turning right distance.
C. Entrances onto Town roads. All entrances onto Town
roads shall be subject to the review and approval of the Town Superintendent
of Public Works. Such entrances include but are not limited to private
residential driveways, commercial or business entrances, private roads
and the like. The offeror shall design and construct all entrances
within the limits of the right-of-way with sufficient sight distance
and with a grade no more than one inch per foot from the curb to the
right-of-way line.
(1)
Driveways. The minimum width of the driveway
pavement at the curb or road pavement line shall be 15 feet, tapering
to a minimum of 10 feet at the right-of-way line. All driveways shall
have a minimum six-inch run-of-bank gravel foundation course from
the curb to the right-of-way line and no less than a two-inch hot
mix asphalt concrete wearing course from the curb or street pavement
line to the right-of-way line, which shall be applied during or after
the laying of the road pavement. All driveways shall be graded to
the satisfaction of the Town Superintendent of Public Works and the
Town Engineer prior to the surfacing of such driveways.
(2)
Private roads.
(a)
The width of private road accesses onto Town
roads shall be 18 feet and shall have, in addition, three-foot swales
on both sides of the road, drained to a location so as not to have
a deleterious effect on drainage within the Town right-of-way, as
acceptable to the Town Superintendent of Public Works and the Town
Engineer.
(b)
Within the Town right-of-way, said private road
shall have a foundation course which shall consist of a minimum of
eight inches of crushed shale or graded gravel base, with a two-inch
choker course of tailings or fine dust-free material placed on top
of said base course, all of which will be compacted to maximum density.
A final surface treatment finish of double application oil emulsion
and stone shall be applied to result in a dust-free surface. Each
oil application shall be 0.5 gallon per square yard, and the stone
utilized shall be 3/8 inch.
(c)
The slope of private roads at their intersection
with Town roads shall be -2% grade from the edge of existing Town
road pavement for a minimum of 30 feet, unless otherwise approved.
The intersection angle of the proposed private road with respect to
the Town road shall be as close to 90° as possible.
(3)
Other entrances. Commercial, business and other
entrances shall be a maximum of 30 feet in width, unless otherwise
approved by the Town Superintendent of Public Works and the Town Engineer.
Construction details of the pavement for the entrance roadway/drive
within the Town right-of-way shall, at minimum, meet the minimum requirements
for the type road being intersected with. All intersections shall
be provided with drainage facilities acceptable to the Town Superintendent
of Public Works and the Town Engineer. Roadway/drives shall be -2%
grade from the edge of existing Town road pavement for a minimum of
30 feet, unless otherwise approved. The intersection angle of the
roadway/drive shall be as close to 90° as possible.
D. Curbs. On all roads, unless otherwise approved as noted in §
A161-7C of these specifications, portland cement concrete curbs shall be constructed on both sides of the street, as shown in Figures 1, 2 and 3, prior to laying road pavement to the dimensions and specification shown in Figure 7. A base course of four inches of run-of-bank gravel, tamped and free of stone over two inches in thickness, shall be laid under all curbing. Concrete shall be used and shall be finished and cured to the satisfaction of the Town Superintendent of Public Works and the Town Engineer. Concrete shall conform to §
A161-19 of these specifications. The offeror, at his own expense, shall replace any curbing that has settled, cracked, scaled or become damaged in any way by the offeror before and within the one-year maintenance period after dedication. Curbs shall be depressed five inches at all driveways. Stone curbs or precast curbs may be substituted only upon the written approval of the Superintendent of Public Works.
E. Sidewalks. On all streets, unless otherwise approved
by the Town Board, portland cement concrete sidewalks shall be constructed
on one side of the street (or both, if so required by the Town Board),
as shown in Figure 7. Concrete shall conform to §
A161-19 of these specifications and shall be finished and cured to the satisfaction of the Town Superintendent of Public Works and the Town Engineer. The offeror, at his own expense, shall replace any sidewalks that have settled, cracked, scaled or become damaged in any way by the offeror before and within the one-year maintenance period after dedication. Sidewalks shall be depressed at all driveways.
F. Intersections.
(1)
All intersections with existing Town roads shall be constructed with the edge of pavement having a radius of 25 feet. Intersections within a development shall be constructed with the edge of pavement having a radius of 25 feet. All intersecting roads shall have a horizontal sight distance of no less than 250 feet in each direction and shall comply with §
A161-12B of this specification.
(2)
All intersections with existing county roads
shall conform to the Policy and Standards - Permit Work within County
Right-of-Way (latest edition), and shall be subject to the approval
of the County Commissioner of Public Works and the review of the County
Department of Public Works, in accordance with Article V, § 102,
and Article VI, § 136, of the Consolidated Laws of New York.
(3)
Where a proposed road intersects a Town or county
road, the approved plans will show the proposed type, length and diameter
of pipe and drainage flow along said road. The pipe will be installed
and paid for by the offeror under the review of the Town Superintendent
of Public Works, the Town Engineer and the County Commissioner of
Public Works or his representative, as applicable. The County Commissioner
of Public Works shall be notified of all intersections with county
roads for approval of location, grade and drainage structures prior
to any construction of the proposed street.
All materials used as part of the road structure
are subject to the approval of the Town Superintendent of Public Works
and the Town Engineer. Prior to the delivery of any materials or the
construction of any work, the offeror shall submit to the Town Engineer
data and testing results, and samples if requested, for all materials
proposed to be used. No material shall be delivered or placed until
the proposed materials have been accepted.
A. Foundation course (subbase), select granular material.
(1)
Description. As part of the construction of
all Town roads or in the preparation of a road for offering to the
Town, the offeror shall furnish and place a select granular material
foundation course of gravel, blast furnace slag, broken stone or other
acceptable granular material in the places designated on the plans
and in such other locations as field conditions require. The thickness
and locations of the foundation course will be as shown on the typical
cross sections, as shown in the figures attached to these specifications.
(2)
Materials.
(a)
All granular material acceptable for this item
shall be of sound, hard, durable stone, gravel or blast furnace slag,
well graded from coarse to fine, and shall meet the approval of the
Town Superintendent of Public Works and the Town Engineer. The particles
shall not exceed such size as will pass through a two-inch square
hole; 30% to 65%, by weight, shall pass the one-fourth-inch square
sieve; 5% to 40%, by weight, shall pass the No. 40 mesh sieve; and
not more than 10%, by weight, shall pass the No. 200 mesh sieve, as
determined by washing through the sieve in accordance with ASTM Designation
D422 (latest revision). The particles passing the No. 40 mesh sieve
shall have a maximum Plasticity Index of 5. Of the particles retained
on the one-half-inch square sieve, not more than 30%, by weight, shall
consist of flat or elongated pieces. A "flat or elongated piece" is
defined herein as one the greatest dimension of which is more than
three times the least dimension.
(b)
The quality of the gravel, stone or slag particles
shall be determined by the magnesium sulphate soundness test. The
maximum percent loss at four cycles, by weight, shall be 20.
(c)
The source of the material shall be stripped
of all sod, topsoil, overburden and other objectionable material before
the excavation operations for the material are started and shall be
kept stripped at a minimum of 30 feet from the top of the working
face of the source at all times.
(d)
The material shall be stockpiled on site or
otherwise be made available for inspection by the Town Superintendent
of Public Works and/or the Town Engineer prior to placement. Prior
to material being delivered to the site, the developer/offeror shall
furnish the Town with certified laboratory test results for the material
to be utilized.
(e)
Should, at any time during work and for any
reason, in the opinion of the Town Superintendent of Public Works
or the Town Engineer, the material fail to conform to the specified
quality and gradation requirements, the offeror shall, by the addition
of selected acceptable material and/or satisfactory manipulation,
produce a material meeting the above requirements, and he shall retest
the material to demonstrate compliance to the satisfaction of the
Town Superintendent of Public Works and the Town Engineer.
(f)
It is the intent of this specification to provide
a foundation course material meeting or exceeding the requirements
of Gradation Type No. 4 subbase material, as specified under Section
304 of the New York State Department of Transportation Standard Specifications
- Construction and Materials (latest revision).
(3)
Construction details.
(a)
After excavation from the source and processing
and blending, if necessary, the material shall be stockpiled. Stockpiles
shall be located at a distance of not less than 50 feet from the outside
bottom edge of the conical stockpile built up under the processing
plant conveyor or not less than 50 feet from the toe of the working
face of the source. Unless otherwise approved, in writing, these stockpiles
shall be formed in layers having a maximum thickness of two feet and
to a height not exceeding 12 feet and shall contain not less than
1,000 cubic yards or the amount needed for the job, whichever is smaller.
Removal of material from stockpiles for placement on the grade shall
be by side excavation along nearly vertical faces for the full depth
of the stockpile. The use of a clamshell-type bucket for loading the
removal trucks or the use of pan-type scrapers for moving the stockpile
material to its final position as subbase course will not be permitted.
(b)
No material shall be added to a stockpile after
the stockpile has been sampled for approval. Only material from approved
stockpiles shall be placed on the grade for this item. The presence
of any oversize particles in the stockpile will be cause for rejection
of the entire stockpile.
(c)
No material shall be removed for use from any
stockpile until the stockpile has been sampled, tested and approved
by the Town Superintendent of Public Works and the Town Engineer for
placement on the grade. Approval of a stockpile for placement on the
grade shall not relieve, in any degree, the full responsibility of
the offeror to furnish, in its compacted position, a subbase course
of select granular materials, the final condition of which conforms
to all requirements of the specifications for this item.
(d)
The spreading of any layer of this material
shall be done with spreader equipment acceptable to the Town Superintendent
of Public Works and shall be spread to such thickness that the maximum
depth of the layer, after compaction, will be six inches. Spreading
from piles dumped on the roadway will not be permitted. No segregation
of large or fine particles will be allowed, but the material, as spread,
shall be well graded, with no pockets of fine material. Water shall
only be added and in such amounts as acceptable to the Town Superintendent
of Public Works and the Town Engineer and only as necessary to obtain
satisfactory compaction.
(e)
When the moisture content of the layer is within
the limits for proper compaction, the entire surface shall be rolled
with a pneumatic-tired roller having an operating weight of between
1,000 and 2,500 pounds per tire or a smooth-steel-wheel roller having
a minimum weight of 10 tons. Each portion of the layer shall be covered
by a minimum of eight passes of the roller.
(f)
For heavier, vibratory or more efficient types
of approved compaction equipment, the minimum number of passes required
on all portions of each layer shall be acceptable to the Town Superintendent
of Public Works. In limited areas, where the use of a roller is impractical,
approved vibrating plate compactors or impact rammers shall be used
to compact the material.
(g)
After compaction, the top surface of this course
shall not extend above nor more than 1/2 inch below true grade and
surface at any location. The foundation course, at any location, shall
be compacted, finished and completed to the above tolerance and approved
by the Town Superintendent of Public Works before any succeeding course
is placed at that location. Any depressions or holes shall be filled
with approved coarse sand or screenings conforming to specifications
and the surface rerolled.
(h)
In all cases, this subbase course must be so
thoroughly compacted that it will not weave under the roller.
(i)
The width of the layer of this subbase course
shall be restricted to that required for placement of the lane being
paved and shall not be laid in excess of 500 linear feet without being
compacted. No traffic or hauling other than that necessary for bringing
material for the next course shall be permitted over this course.
Should the subgrade or any other material become churned up into or
mixed with this foundation course through any reason whatsoever, the
offeror shall, at his own expense, remove such mixtures and repave
with select granular material acceptable for this item.
B. The offeror shall assume full responsibility for any
contamination and/or degradation of any part of this course during
construction and shall, at his own expense, remove any and all portions
of this course which do not conform to the requirements of these specifications
and replace these portions with specified material.
Pavement; base course. After the foundation
course has been inspected and accepted by the Town Superintendent
of Public Works and the Town Engineer, with the three-month minimum
settlement period elapsed, and found to be at a grade allowing the
proper depth of finished pavement, one of the following two base courses
shall be laid (selection in accordance with road classification):
A. Cold mix bituminous pavement.
(1)
Material.
(a)
The base course shall consist of constructing
a course of cold mix bituminous pavement on a prepared base in accordance
with these specifications and in conformance with the lines, grades,
thicknesses and detail shown on the typical cross sections for the
type of road involved, as shown on the figures provided with this
specification.
(b)
A cold mix base course shall consist of a mixture
of aggregate and bituminous material proportioned in accordance with
Table 405-1 of the New York State Department of Transportation Standard
Specifications, for a Type 1 open coarse mix.
(c)
Aggregate particles shall not exceed such size
as will pass through a one-inch square hole; 90% to 100%, by weight,
shall pass a one-half-inch square hole; 15% to 45%, by weight, shall
pass a one-fourth-inch square hole; 0% to 10%, by weight, shall pass
a one-eighth-inch square hole; and 0% to 1% shall pass the No. 200
mesh sieve, as determined by washing through the sieve with ASTM Designation
D422 (latest revision).
(d)
The asphalt bituminous material content shall
be between 4.7% and 7.0% total emulsion percentage based on total
mix weight. When crushed air-cooled blast furnace slag aggregate is
selected, the bituminous material content shall be increased by 25%
of the values stated.
(e)
Aggregates shall meet the requirements of Section
703-02, Coarse Aggregates, for the sizes specified; bituminous material
shall meet the requirements of Section 702, Bituminous Material, and
be of an appropriate grade for the conditions, both sections as referenced
herein from the New York State Department of Transportation Standard
Specifications. Aggregates and bituminous material shall be as acceptable
to the Town Superintendent of Public Works and the Town Engineer.
Hydrated lime, if required, shall meet the requirements of Section
712.04, Hydrated Lime, of said state specifications.
(2)
Placement.
(a)
Bituminous material or mixture shall not be
applied on any soft surfaces, when the surface is wet, when the temperature
of the surface on which the mixture is to be placed is below 45°
F. or when other weather conditions would prevent proper construction
of the pavement. The following equipment shall be required:
[2]
Roller (eight- to twelve-ton).
[6]
Motor grader, if required.
(b)
The travel plant mixer shall be capable of continuously
mixing aggregates with bituminous material in the specified proportions
in a mixer unit and then depositing the mixture on the prepared base.
(c)
All equipment and the condition of the equipment
shall meet the approval of the Town Superintendent of Public Works.
(d)
The roadway surface to be covered shall be free
from holes, depressions, bumps, waves and corrugations. Any unsuitable
surface areas shall be repaired by replacement of the unstable materials
or by patching with a material to produce a tight surface having the
same elevation as the surrounding surface. The roadway surface shall
be broomed, to the satisfaction of the Town Superintendent of Public
Works, to remove loose material.
(e)
The aggregate and asphalt shall be thoroughly
mixed so that the bituminous material is uniformly distributed throughout
and all aggregate particles are completely coated. If hydrated lime
is used to hasten the breakdown of emulsion, the lime may be added
to the mix just prior to the discharge of the material from the mixer.
(f)
The mixture shall be deposited on the prepared
base either in a windrow at the back of the travel mixer or mechanically
spread in a uniform layer so as to produce the specified thickness
after compaction. If deposited in a windrow, it shall be spread over
the entire roadway surface by motor grader or other approved spreader
to produce the specified thickness after compaction.
(g)
After spreading, the mixture shall be thoroughly
and uniformly compacted with either a self-propelled steel-wheeled
roller or smooth-tread pneumatic-tired roller, or both, to obtain
a thoroughly compacted pavement. The number of roller passes to achieve
the desired compaction shall be as acceptable to the Town Superintendent
of Public Works and the Town Engineer.
(h)
The finished surface of the pavement shall be
tested with a sixteen-foot straight edge laid parallel with the center
line of the pavement. Any area exceeding a one-fourth-inch variation
from the surrounding area shall be satisfactorily corrected or removed
and replaced.
(i)
Immediately after compacting the road mix, No.
1 size key stone meeting the requirements of Section 703-02, Coarse
Aggregates, shall be uniformly spread upon the surface at the rate
of 10 to 20 pounds per square yard and the course rolled thoroughly.
The pavement shall not be opened to traffic for a minimum of three
days after placing the key stone and before placing the seal coat.
B. Hot mix asphalt concrete pavement.
(1)
Material.
(a)
The base course shall consist of a hot mix asphalt
concrete, conforming in all respects to the requirements for Base
Course, Type 1, as stated in the New York State Department of Transportation
Standard Specifications - Construction and Materials, Section 401
(latest edition). A hot mix base course shall be constructed on a
prepared base in accordance with these specifications and in conformance
with the lines, grades, thicknesses and detail shown on the typical
cross sections for the type of road involved, as shown on the figures
provided with this specification.
(b)
A hot mix base course shall consist of aggregates,
filler, if required, and bituminous material proportioned in accordance
with Table 401-1 of the New York State Department of Transportation
Standard Specification for a Type 1 dense base course.
(2)
Placement.
(a)
Pavement shall not be placed on any wet surface,
any soft surfaces or when the surface temperature is less than 45°
F. Temperature shall be measured on the surface where the paving is
to be placed and the controlling temperature shall be the average
of three temperature readings taken at locations 25 feet, plus or
minus, apart.
(b)
The roadway surface to be covered shall be free
from holes, depressions, bumps, waves and corrugations. Any unsuitable
surface areas shall be repaired by replacement of the unstable materials
or by patching with a material to produce a tight surface having the
same elevation as the surrounding surface.
(c)
All equipment and the condition of the equipment
shall meet the approval of the Town Superintendent of Public Works.
Pavement; finish course. After the base course
has been placed, inspected and approved by the Town Superintendent
of Public Works, one of the following two top courses shall be laid
(selection in accordance with road classification):
A. Hot mix asphalt concrete pavement.
(1)
Material.
(a)
The finish course shall consist of a hot mix
asphalt concrete, conforming in all respects to the requirements for
Top Course, Type 6F, as stated in the New York Department of Transportation
Standard Specification - Construction and Materials (latest edition).
(b)
A hot mix finish course shall be constructed
in accordance with these specifications and in conformance with the
lines, grades, thicknesses and detail shown on the typical cross sections
for the type road involved, as shown on the figures provided with
this specification.
(c)
A hot mix finish course shall consist of aggregate,
filler, if required, and bituminous material proportioned in accordance
with Table 401-1 of the State Specification for a Type 6F dense granular
top course.
(2)
Placement. Pavement shall not be placed on any wet surface or when the surface temperature is less than 45° F. Temperature shall be measured as noted in §
A161-15B(2) of this specification.
B. Double bituminous surface treatment (alternate finish
course).
(1)
Material.
(a)
Only when approved by the Town Superintendent
of Public Works and the Town Engineer and only for minor roads an
alternate finish course consisting of a double bituminous surface
treatment wearing course shall be permitted. Such alternate finish
course will only be permitted when the base course has been constructed
at the thickness associated with this alternate pavement structure.
All work shall be performed per the detail shown on the typical cross
sections, as shown on the figures provided with this specification.
(b)
The bituminous material required for the surface
treatment shall meet the requirements of New York State Department
of Transportation Section 702, Bituminous Materials, and shall be
an asphalt emulsion.
(c)
The aggregate for surface treatments shall be
crushed stone, meeting the requirements of New York State Department
of Transportation Section 703-02, Coarse Aggregates. In addition,
any aggregate used for surface treatments on pavement shall not contain
more than 5% chert. The aggregate size for the first course shall
be No. 1 and the second course shall contain aggregate size No. 1A.
(2)
Placement.
(a)
Bituminous material shall not be applied on
a wet surface, when the air temperature is below 50° F. or greater
than 95° F., unless otherwise permitted, or when weather conditions
would prevent the proper construction of the surface treatment. The
following equipment shall be required:
[1]
Bituminous material distributor.
[2]
Pneumatic rubber tire roller.
(b)
The bituminous material distributor shall be
so designed, equipped, maintained and operated that the bituminous
material at even heat can be applied uniformly on variable widths
of surface up to 15 feet at readily determined and controlled rates
from 0.05 to 2.0 gallons per square yard, with uniform pressure, and
with an allowable variation from any specified rate not to exceed
0.02 gallon per square yard. Distributor equipment shall include a
tachometer, accurate volume measuring devices or a calibrated tank
and a thermometer for measuring temperatures of tank contents. Distributors
shall be equipped with a power unit for the pump and full circulation
spray bars adjustable laterally and vertically.
(c)
The distributor and/or transport shall be equipped
with a sampling valve so designed and installed as to be nonclogging
and safe. When samples are taken through such valves, they shall be
considered representative of all material in the tank.
(d)
The pneumatic rubber tire roller shall be self-propelled
and have oscillating wheels with smooth-tread tires. The tire or contact
pressure shall be as acceptable to the Town Superintendent of Public
Works. The roller shall be operated at a maximum speed of five miles
per hour.
(e)
The aggregate spreader shall produce a uniform
spread of aggregate between the range of 10 to 50 pounds per square
yard.
(f)
The bituminous material distributor and aggregate
spreader shall be subject to the acceptance of the Town Superintendent
of Public Works.
(g)
The surface shall be free from irregularities
to provide a reasonably smooth and uniform surface to receive the
treatment. Areas which are stable and firm and require one inch or
less in thickness to patch or shape the surface may be patched with
surface treatment materials. Unstable and/or corrugated areas shall
be removed and replaced. Areas requiring replacing, patching or shaping
in excess of one inch in thickness shall be constructed with materials
acceptable to the Town Superintendent of Public Works and the Town
Engineer.
(h)
A power broom shall be used to clean any loose
material from the pavement surface before the bituminous material
is applied. Manhole covers, drop inlets, catch basins and any other
structures within the roadway area shall be protected against the
application of the surface treatment materials.
(i)
Bituminous material shall be applied by means
of a pressure distributor in a uniform, continuous spread over the
section to be treated and within the temperature range specified.
The quantity of bituminous material to be used shall be 0.5 gallon
per square yard for the first course and 0.4 gallon per square yard
for the second course for the indicated aggregate gradation, unless
otherwise approved. A strip of building paper at least three feet
in width and with a length equal to that of the spray bar of the distributor,
plus one foot, shall be used at the beginning of each spread. If the
cutoff is not positive, the use of paper may be required at the end
of each spread. The paper shall be removed and disposed of in a satisfactory
manner. The distributor shall be moving forward at proper application
speed at the time the spray bar is opened. Any skipped areas or deficiencies
shall be corrected. Junctions of spreads shall be carefully made to
assure a smooth riding surface.
(j)
The length of spread of bituminous material
shall not be in excess of that which trucks loaded with cover coat
material can immediately cover.
(k)
The spread of bituminous material shall not
be more than six inches wider than the width covered by the cover
coat material from the spreading device. Under no circumstances shall
operations proceed in such a manner that bituminous material will
be allowed to chill, set up, dry or otherwise impair retention of
the cover aggregate.
(l)
The distributor, when not spreading, shall be
parked so that the spray bar or mechanism will not drip bituminous
material on the surface of the traveled way.
(m)
Immediately following the application of the
bituminous material, cover aggregate shall be spread in the range
of 15 to 25 pounds per square yard for the indicated aggregate, unless
otherwise approved. Spreading shall be accomplished in such a manner
that the tires of the trucks or aggregate spreader at no time contact
the uncovered and newly applied bituminous material.
(n)
Immediately after the cover aggregate is spread,
any deficient areas shall be covered by additional material. If the
application of the aggregate cover by the spreader is not uniform,
the Town Superintendent of Public Works may require the contractor
to use a drag broom before rolling. Pneumatic tire rolling shall begin
immediately and shall be continued until three complete coverages
are obtained.
(o)
Any free bituminous material on the surface
caused by a deficient amount of cover aggregate shall be covered in
such a manner so as not to displace imbedded material. Excess material
shall be swept from the entire surface by means of brooms. The surface
shall be swept at the time determined by the Town Superintendent of
Public Works.
(p)
Traffic shall be discontinued on the lane being
surface treated; and as soon as the final layer is applied and rolled,
controlled traffic may be permitted thereon. Traffic shall be maintained
at a speed not to exceed 15 miles per hour for two to four hours after
rolling. The time and minimum requirements of traffic control shall
be as acceptable to the Town Superintendent of Public Works.
(q)
Sufficient time shall elapse between the completion
of the first course and the placing of the surface course so that
the bituminous material in the first course has time to set or cure.
A. Stabilization fabric. Where called for in the design
or required by the Town Superintendent of Public Works and/or the
Town Engineer, the offeror shall, at his own expense, provide and
install a high-tensile-strength, high modules (low deformation under
load) woven-type stabilization fabric under the pavement subbase.
B. Fabric shall meet the following minimum properties
in accordance with American Society for Testing and Materials test
methods:
|
Item
|
Value
|
---|
|
Grab tensile strength
|
300 pounds
|
|
Grab tensile elongation
|
35 maximum
|
|
Modulus (at 10% elongation)
|
140 pounds
|
|
Burst strength
|
600 pounds per square inch
|
|
Trapezoid tear strength
|
120 pounds
|
|
Puncture resistance
|
130 pounds
|
All materials used as part of the road shall
be subject to the approval of the Town Superintendent of Public Works
and the Town Engineer. Prior to the delivery of any materials or the
construction of any work, the offeror shall submit to the Town Engineer
data, test results, manufacturer's literature and/or samples for all
materials proposed to be used. No material shall be delivered or placed
until the proposed materials have been accepted.
A. General.
(1)
All concrete used in the construction of concrete
curbs, sidewalks, headwalls, catch basins and other miscellaneous
items shall be plant mix portland cement concrete, complete with reinforcing
as called for in the details provided with this specification. All
concrete provided shall have a minimum compressive strength of 3,500
pounds per square inch at 28 days, with the exception of headwalls
and any other structural elements, which shall have a minimum compressive
strength of 4,000 pounds per square inch at 28 days.
(2)
The quality of all types of finished concrete
surfaces shall be that which can be truly classified as good standard
practice in the trade for each respective type or kind of surface.
(3)
The portland cement concrete shall consist of
a homogeneous mixture of cement, water, fine aggregate, course aggregate
and admixtures proportional and mixed according to the American Concrete
Institute Code of latest edition and these specifications.
B. Reinforcement.
(1)
Reinforcing bars shall conform to the requirements
of ASTM A615 (latest revision), Grade 40.
(2)
Welded plain wire fabric for concrete reinforcement
shall conform to Specifications for Welded Steel Wire Fabric for Concrete
Reinforcement (ASTM A185), except that welded intersections shall
be spaced not farther apart than 12 inches in the direction of the
principal reinforcement.
(3)
All bar accessories for support, holding and
spacing of reinforcement shall be in accordance with the recommendations
of the Manual of Standard Practice for Detailing Reinforced Concrete
Structures of the American Concrete Institute except as specifically
modified by details on the design drawings as approved.
(4)
Welding of reinforcement shall conform to AWS
D12.1. Plastic-tipped chairs are required for all concrete except
for slabs on ground.
C. Concrete mix.
(1)
Cement shall be portland cement, Type 2, conforming
to ASTM C160. Fine aggregate shall meet the following gradation requirements,
unless otherwise approved:
|
Sieve Size
|
Passing by Weight
|
---|
|
3/8-inch
|
100%
|
|
No. 4
|
90% to 100%
|
|
No. 8
|
75% to 100%
|
|
No. 16
|
50% to 85%
|
|
No. 30
|
25% to 60%
|
|
No. 50
|
10% to 30%
|
|
No. 100
|
1% to 10%
|
|
No. 200
|
0% to 3%
|
(2)
Coarse aggregate shall be crushed stone, crushed
gravel or crushed slag. This aggregate shall be clear and uncoated
and meet the following gradation requirements, unless otherwise approved:
|
Sieve Size
(inches)
|
Passing by Weight
(percent)
|
---|
|
21/2
|
—
|
|
2
|
—
|
|
11/2
|
100%
|
|
1
|
93% to 100%
|
|
1/2
|
27% to 58%
|
|
1/4
|
0% to 8%
|
(3)
Air-entraining agents shall conform in all respects
to the requirements of ASTM C260, except that nonliquid agents will
not be permitted. The testing to determine if the agent yields the
required properties shall be performed in accordance with ASTM C233.
(4)
All concrete shall contain an air content between
4% and 8%. The air content shall be determined in accordance with
ASTM C173.
(5)
Admixtures shall be added in the amounts necessary
to achieve the required air content and/or set retardation. These
materials shall not be considered as part of the solid volume. Other
admixtures shall not be used without acceptance by the Town Engineer.
(6)
Water shall be added in the amounts required
to produce a slump between 21/2 inches and 31/2 inches while maintaining
a water/cement ratio of approximately 0.65 by weight.
D. Installation.
(1)
A record of each concrete delivery shall be
produced and provided to the representatives of the Town. This record
shall contain the quantities of each aggregate component, cement,
water and admixture(s) for each batch. Additionally, the batching
record shall show the batch number, day, month, year and time of day.
(2)
The offeror shall, at his own expense, provide
representatives for the taking of concrete cylinders and making slump
tests in the field, as well as retain the services of a concrete testing
laboratory to make all such necessary tests and provide acceptable
written reports to the Town Engineer.
(3)
The personnel taking the concrete cylinders
and making slump tests in the field shall be provided by the offeror
or the testing laboratory and shall be qualified field technicians
completely familiar with the required tests. All personnel are subject
to acceptance of the Town.
(4)
The type and capacity of all equipment used
for mixing, transporting, placing and finishing concrete shall be
subject to the acceptance of the Town Engineer.
(5)
Before depositing concrete, the excavations
shall be free of water, frost or loose or softened earth; the forms
shall be cleaned of all debris, ice or snow.
(6)
No concrete shall be placed when the atmospheric
temperature is below 40° F. unless permission to do so is granted,
in writing, by the Town Superintendent of Public Works and the Town
Engineer. When cold weather concreting is approved, the same shall
conform to ACI 306 (latest revision), Standard Recommended Practice
for Cold Weather Concreting.
(7)
During periods of abnormally hot and dry weather,
the contractor shall take all such appropriate actions and means to
place the concrete immediately upon arrival at the site, finishing
the work as soon as possible and immediately curing so as to retain
moisture in the concrete and reduce temperature buildup. All concreting
in hot weather shall conform to ACI 305 (latest revision), Standard
Recommendation Practice for Hot Weather Conditions.
(8)
All curing shall comply to the requirement of
ACI Standard 308 (latest revision), Standard Recommended Practice
for Curing Concrete.
(9)
Expansion joints for concrete sidewalks and
curbs shall be one-half-inch premolded expansion joint material meeting
the specifications of ASTM D-1751.
(10)
All porous or defective concrete of any kind
occurring prior to final acceptance of the work shall be remedied
by the offeror at his expense and to the satisfaction of the Town
Engineer and the Town Superintendent of Public Works.
For purposes of standardization and proper,
timely and safe replacement, all manhole cover castings shall be Campbell
No. 1007C and shall be considered standard for supply on Cornwall
Town roads. Substitution of or-equal castings shall be only when approved,
in writing, by the Town Superintendent of Public Works.
Where called for in the design or required by
the Town Superintendent of Public Works and/or the Town Engineer,
the offeror shall, at his own expense, provide and install galvanized
steel guide rail. Rail shall be corrugated type, W-beam type, typically
with W 6 x 9 posts, terminal sections, anchors and details of construction
as acceptable to the Town Superintendent of Public Works and the Town
Engineer. Rail shall have a minimum weight per foot of 6.8 pounds.
Rail shall be mounted to the galvanized posts with galvanized bolts
and plate washers. Where the top of rail height is over 27 inches,
a cold-formed channel rub rail shall be provided.
A. Signs shall be double-faced, assembled with engineer
grade reflective sheeting on extruded aluminum blades. Signs shall
be white characters on a green background, six inches in height, by
length as necessary for specific installation. Letters shall be three
inches, upper case, FHWA Series C, of reflective sheeting. All signs
shall be manufactured per United States Bureau of Public Roads standards
and shall be chemically treated to meet ASTM B449 (latest revision)
for pretreatment for paint or reflective sheeting.
B. Sign posts shall be 23/8 inches outside diameter,
sixty-five-hundredths-inch wall thickness, hot-dipped galvanized steel,
ten-foot length, set three feet into solid ground.
C. Identification signs for private roads shall be of
identical configuration, mounted below the private road's street name
identification sign. The sign shall bear the characters "PRIVATE ROAD."
D. All street names, including those for private roads,
are subject to the approval of the Town Board, and no name created
shall be identical or undesireably similar to any existing street
name. Any name created shall be registered with the Town Clerk.
A. Traffic control devices shall only be installed where
approved by the Town Board and, if applicable, the other governmental
agency having jurisdiction for the intersecting roadway involved.
All signs and pavement markings shall be of the type, size, color,
shape and general construction and placement, in accordance with the
criteria called for in the Manual of Uniform Traffic Control Devices
(latest revision), as promulgated by the New York State Department
of Transportation, Traffic and Safety Division.
B. Signs shall be constructed of stock aluminum, manufactured
in accordance with United States Bureau of Public Roads standards
and treated to meet ASTM B449 for pretreatment for paint or reflective
sheeting.
C. Signs shall be mounted to heavy-weight rib-back channel
posts finished with a green baked-enamel coating. Posts shall be three
pounds per foot weight, manufactured from high tensile steel. Posts
shall be set a minimum of three feet into solid ground, of a minimum
ten-foot overall length.
A. Encroachments into Town right-of-way. It shall be
considered unlawful for any person, persons, developer, firm or other
entity to construct or cause to have constructed or place or otherwise
create encroachments which are located within the Town right-of-way
unless the specific item has been submitted to the Town and approved
in accordance with this specification or other applicable laws.
B. Should any signs, landscaping elements, shrubs or
other plants, improperly placed mailbox or any other obstruction or
encroachment so exist and be deemed a hazard or otherwise an unsafe
or unacceptable condition by the Town Superintendent of Public Works,
the person, persons, developer, firm or other entity responsible for
such item shall cause the encroachment to be immediately removed.
Should this fail to occur within a time deemed reasonable by the Superintendent,
the Town reserves the right to correct the encroachment, with the
cost for the same to be borne by the responsible party.
A. No mailbox or newspaper delivery box, hereafter referred
to as "mailbox," will be allowed to exist within a Town right-of-way
if it interferes with the safety of the traveling public or the function,
maintenance or operation of the roadway or pedestrian system. A mailbox
installation that does not conform to the provisions of this regulation
will be considered an unauthorized encroachment.
B. The location and construction of mailboxes shall conform
to the rules and regulations of the United States Postal Service,
as well as to standards established by this specification.
C. No mailbox will be permitted where access is obtained
from the lanes of a major road or where access is otherwise prohibited
by law or regulation.
D. In general, mailboxes shall be located on the right-hand
side of the roadway in the direction of the delivery route except
on one-way streets where they may be placed on the left-hand side.
The bottom of the box shall be set at an elevation established by
the United States Postal Service, usually between three feet six inches
and four feet zero inches above the roadway surface. The roadside
face of the box shall be offset from the edge of the traveled way
a minimum distance of the greater of the following: eight feet, where
no paved shoulder exists; the width of the all-weather shoulder present,
plus eight to 12 inches; or the width of an all-weather turnout, plus
eight to 12 inches.
E. On curbed streets, the roadside face of the mailbox
shall be set back from the face of the curb a distance between six
and 12 inches. On residential streets without curbs or all-weather
shoulders and that carry low traffic volumes operating at low speeds,
the roadside face of a mailbox shall be offset between eight and 12
inches behind the edge of pavement. Mailboxes shall not be placed
so as to obstruct any sidewalk or established pedestrian way.
F. It shall be the responsibility of the owner to coordinate
these requirements with the requirements of the United States Postal
Service.
A. After all construction within the right-of-way has
been completed, all nonpaved areas shall be finish graded and seeded.
Seeding mix shall be as follows:
|
Component
|
Application
(pounds per 1,000 square feet)
|
---|
|
Perennial ryegrass (Lolium perenne)
|
1,000
|
|
Fertilizer (10-20-10)
|
14
|
|
Limestone
|
135
|
|
Mulch (unrotted straw or salt hay)
|
70
|
B. All seeding shall be performed on a ground surface
consisting of a minimum of four inches of topsoil. This work may be
performed at any season of the year when a mulch is used unless otherwise
specified. When conditions of high winds, excessive moisture or ice
are such that satisfactory results are not likely to be obtained,
the work shall be stopped and will be resumed only when the desired
results are likely to be obtained or when acceptable corrective measures
and procedures are adopted.
C. Areas to be seeded shall be maintained at acceptable grades. Irregularities
which will form low places and hold water shall be eliminated. The
offeror shall care for the seeded and mulched areas until the end
of the maintenance security term. Such care shall consist of repairing
any areas damaged following the seeding or mulching operations due
to wind, water, fire or other causes. Such damaged areas shall be
repaired to reestablish the condition and grade of the area prior
to seeding and shall then be refertilized, reseeded and remulched
as specified herein.
[Amended 1-9-2017 by L.L.
No. 1-2017]
No owner or occupant or other person shall place,
keep, permit or suffer to be placed or kept on any sidewalk in front
of, adjoining or adjacent to such premises any goods, wares, merchandise,
boxes, barrels, display signs or material things of any kind or description
nor shall he in any manner obstruct any such sidewalk or in any manner
obstruct or interfere with the use of any such sidewalk. Nothing contained
in this local law shall prevent such persons from placing foods, wares
or merchandise on the sidewalk temporarily while loading or unloading
the same, provided that it be done without unnecessary delay and provided
that such goods, wares or merchandise are not allowed or permitted
to remain on such sidewalks within the prohibited area for a period
longer than one hour.
Final decision as to the interpretation of any
part of these road specifications shall rest with the Town Superintendent
of Public Works. He shall have the authority to modify the requirements
of these specifications when, in his opinion, conditions make it impracticable
to follow the strict letter of these specifications, when conditions
make it unnecessary to do so and when it is in the best interest of
the Town of Cornwall.