The provisions contained herein shall be applied
to applications for site plan and/or major subdivision approval to
the extent applicable.
The governing body hereby finds that uniformity
in the exterior design and appearance of dwellings erected in the
same residential neighborhood tends to adversely affect the desirability
of the immediate and neighboring areas for residential purposes and
impairs existing residential property in such areas; tends to impair
the value of both improved and unimproved real property in such areas;
and tends to deprive the municipality of tax revenue and destroys
a proper balance between the taxable value of real property in such
areas and the cost of municipal services provided therefor. It is
the purpose of this article to prevent these and other harmful effects
of uniformity in design and appearance of dwellings erected in any
housing development in the same residential neighborhood and thus
to promote and protect the general welfare of the community.
A. Not more than one construction permit shall be issued
for any particular single-family detached dwelling unit design in
any housing development consisting of two or more detached dwellings
when the houses are substantially alike in exterior design and appearance
unless such similar houses either are separated by a distance of at
least 300 feet along the street on which the house fronts or are situated
on individual lots which are themselves separated at all points along
the side of the street on which the house fronts by a distance of
at least 150 feet, and are separated at all points along the opposite
side of the street on which the house fronts by a distance of a least
75 feet, whichever distance will provide the least separation between
similar houses.
B. Houses within such specified distance from each other
shall be considered uniform if the same basic dimensions and the same
floor plans are used without substantial differentiations to the front
exterior elevation. Acceptable ways of differentiating between differences
of houses are siding, doors, roofline, setbacks, front design.
C. To insure conformity with the provisions of this chapter,
no construction permit shall hereafter be issued for more than one
dwelling in any housing development until the builder shall post or
cause to be posted on each specific lot on the map of the subdivision
on file with the Construction Official the type and model of each
house for which a construction permit has been or is being issued.
D. The provisions, requirements and standards heretofore
set forth shall not be considered met where there is an attempt to
make minor changes or deviations from building plans and location
surveys, which changes show an obvious intent to circumvent the purpose
of this section.
[Amended by Ord. No. 2002-13]
All streets and off-street parking areas shall
be provided with catch basins and pipes where the same may be necessary
for proper surface drainage. The requirements of this section shall
not be satisfied by the construction of dry wells or other on-site
facilities unless permitted by the Township Engineer.
A. The system shall be adequate to carry off or store
the stormwater and natural drainage water which originates not only
within the lot or tract boundaries, but also that which originates
beyond the lot or tract boundaries. No stormwater runoff or natural
drainage water shall be so diverted as to overload existing drainage
systems or create flooding or the need for additional drainage structures
on other private properties or public lands without proper and approved
provisions being made for taking care of these conditions.
B. Techniques for computing stormwater runoff shall be
as approved by the Township Engineer. The Rational Method of surface
water runoff computation may be used for storm sewers and open channels
with drainage basins up to 25 acres in area. The Soil Conservation
Method (Urban Hydrology For Small Watersheds, Manual No. 55), or other
methods approved by the Township Engineer, shall be used for drainage
basins larger than 25 acres in area.
C. Flow capacity.
(1) Storm sewers, open channels, bridges and culverts,
unless otherwise directed by the Township Engineer, shall be designed
for minimum flow capacities as follows:
|
|
Design Capacity
|
---|
|
Drainage systemsa
|
25 years
|
|
Drainage structuresb
|
100 years
|
|
Open channels
|
As determined by Township Engineer
|
|
NOTES:
|
|
aThe term "drainage
systems" refers to the composite of all drainage infrastructure improvements.
|
|
bThe term "drainage
structures" refers to particular drainage infrastructure improvements
such as bridges and culverts.
|
(2) For retention or detention basins, soil borings shall
be provided at the rate of one boring per 5,000 square feet of basin
surface area. For all linear trenches such as perforated pipe trenches,
borings shall be required at a rate of one boring per 100 linear feet
of trench. Boring depth shall extend as a minimum to the seasonal
high water and to the water table if possible. Boring logs shall be
shown on the site plan and shall include:
(a)
Soil texture as described in the USDA Soil Texture
classification;
(b)
Soil color as described in the Munsell Color
Chart; and
(c)
Estimated depth to seasonal high water.
(3) The location of any system that incorporates infiltration
shall have a minimum two-foot clearance between the invert of the
system and the seasonal high water table.
D. The materials used in the construction of storm sewers,
bridges and other drainage structures shall be in accordance with
specifications of the Standard Specifications for Road and Bridge
Construction of the New Jersey State Highway Department, current edition,
and any supplements, addenda and modifications thereof. Modification
or change of these specifications may be affected only with the knowledge
and written consent of the Township Engineer and Planning Board.
E. Lots shall be graded to secure proper drainage away
from buildings and to prevent the ponding of stormwater except where
retention or detention basins are provided.
F. Drainage structures which are proposed to be located
on state or county highway rights-of-way shall be approved by the
state or county highway engineer's office, and a letter from that
office indicating such approval shall be directed to the administrative
officer and shall be received prior to the granting of final approval.
Drainage structures proposed on a brook or stream with a drainage
area of 1/2 square mile (320 acres) or greater shall be approved by
the New Jersey Division of Water Policy and Supply, and a letter from
that office shall be directed to the administrative officer.
G. Where a lot or tract is traversed by a watercourse,
surface or underground drainageway or drainage system, channel or
stream, there shall be provided and dedicated a drainage right-of-way
easement to the Township conforming substantially with the lines of
such watercourse, and such further width or construction or both as
will be adequate to accommodate expected stormwater runoff in the
future, based upon reasonable growth potential in the Township and,
in any event, meeting any minimum widths and locations shown on any
adopted Official Map or Master Plan. Such easement dedication shall
be expressed on the plat as follows: "Drainage and utility right-of-way
easement granted for the purposes provided for and expressed in the
development ordinance."
[Amended by Ord. No. 84-4]
A. Natural features such as trees, hilltops and views,
natural terrain, open waters and natural drainage lines shall be preserved
whenever possible in designing and development containing such features.
B. No topsoil shall be removed from areas intended for
lawn or open space. Topsoil moved during the course of construction
shall be redistributed so as to provide at least six inches of cover
to all such areas, which shall be stabilized by the approved seeding
and/or planting.
C. A conscious effort shall be made to preserve all worthwhile
trees and shrubs which exist on the site. Stripping trees from a lot
or filling around trees on a lot shall not be permitted unless it
can be shown that grading or construction requirements necessitate
removal of trees, in which case those lots shall be replanted with
trees to reestablish the tone of the area in conformance with adjacent
lots. All newly planted shade trees shall be of nursery stock. Deciduous
trees shall have at least a one-and-one-half-inch caliper at planting,
evergreen trees shall be at least five feet tall, and shrubs shall
be at least two feet tall. All trees shall be of a species approved
by the Board and shall be balled and burlapped. In all cases, a sufficient
number of shade trees shall be provided and planted to insure a minimum
of eight trees per acre of lot area.
[Amended by Ord. No. 84-4]
A. Streets.
(1) All developments shall be served by paved public streets
with an adequate crown. The arrangement of streets not shown on the
Master Plan or Official Map, as adopted by the Township, shall be
such as to provide for the appropriate extension of existing streets
and should conform to the topography as far as practicable.
(2) When a new development adjoins land susceptible of
being subdivided, suitable provisions shall be made for optimum access
of the remaining and/or adjoining tract to existing or proposed streets.
Any proposed development shall utilize existing access provisions
from adjacent developments wherever possible and feasible.
(3) Local streets shall be so planned and identified with
appropriate signs so as to discourage through traffic.
(4) In the event that a development adjoins or includes
existing streets that do not conform to widths as shown on the adopted
Master Plan and/or Official Map or the street width requirements of
this chapter, additional land along either or both sides of said street,
sufficient to conform to the right-of-way requirements, shall be dedicated
for the location, installation, repair and maintenance of streets,
drainage facilities, utilities and other facilities customarily located
on street rights-of-way. The necessary deeds of ownership shall be
furnished, and the dedication shall be expressed as follows: "Street
right-of-way granted permitting the entrance upon these lands for
the purposes provided for and expressed in the Development Ordinance
of the Township." This statement shall in no way reduce the developer's
responsibility to provide, install, repair or maintain the facilities
in the area dedicated by ordinance and/or as shown on the plan and/or
as provided for by any maintenance or performance guarantees. If the
development is along one side only, 1/2 of the required extra width
shall be dedicated. Additionally, that portion of the existing street
or road adjoining or included within a site plan or major subdivision
shall be improved, including excavation, grading, base courses and
surfacing in accordance with the road improvement standards of this
chapter.
(5) The minimum public street right-of-way for Township
streets shall be as approved by the Planning Board, but in no case
shall any municipal street have less than a fifty-foot right-of-way.
Concerning streets under Cape May County jurisdiction, the county
recommends the following rights-of-way for certain of its streets:
|
Name of Street
|
Right-of-Way
|
---|
|
Bay Shore Road
|
66 feet right-of-way (33 feet from center line
of road)
|
|
Fishing Creek Road
|
66 feet right-of-way (33 feet from center line
of road)
|
|
Fulling Mill Road
|
50 feet right-of-way (25 feet from center line
of road)
|
|
Jonathan Hoffman Road
|
50 feet right-of-way (25 feet from center line
of road)
|
|
New England Road
|
50 feet right-of-way (25 feet from center line
of road)
|
|
Ocean Drive
|
86 feet right-of-way (43 feet from center line
of road)
|
|
Seashore Road
|
66 feet right-of-way (33 feet from center line
of road)
|
|
Shun Pike Road
|
86 feet right-of-way (43 feet from center line
of road)
|
|
Sunset Boulevard
|
66 feet right-of-way (33 feet from center line
of road)
|
|
Stimpson Lane
|
50 feet right-of-way (25 feet from center line
of road)
|
|
Tabernacle Road
|
50 feet right-of-way (25 feet from center line
of road)
|
|
Town Bank Road
|
66 feet right-of-way (33 feet from center line
of road)
|
(6) Street intersections shall be as nearly at right angles
as is possible and in no case shall be less than 60º, and approaches
to all intersections shall follow a straight line for at least 100
feet. No more than two streets shall meet or intersect at any one
point, and the center lines of both intersecting streets shall pass
through a common point. Measuring from this common point, two intersections
shall be spaced a sufficient distance to permit a minimum of two lots
between the two street right-of-ways. Any development abutting an
existing street classified as an arterial or collector shall be permitted
only one new street connecting with the same side of the existing
street except where the frontage is sufficient, more than one street
may intersect the arterial or collector street, provided the streets
shall not intersect with the same side of the existing street at intervals
of less than 800 feet. The block corners at intersections shall be
rounded at the curbline with the street having the highest radius
requirement as outlined below determining the minimum standard for
all curblines:
(7) A tangent at least 200 feet long shall be introduced
between reverse curves on arterial and collector streets. When connecting
street lines deflect from each other at any one point, they shall
be connected by a curve with a radius conforming to standard engineering
practice so that the minimum sight distance within the right-of-way
shall be 350 feet for a local street, 500 feet for a collector street
and 800 feet for an arterial street.
(8) Culs-de-sac of a permanent nature (where provision
for the future extension of the street to the boundary of the adjoining
property is impractical or impossible) or of a temporary nature (where
provision is made for the future extension of the street to the boundary
line of adjoining property) shall be no more than 750 feet in length
and shall provide a turnaround at the end with a radius of 50 feet
on the curbline plus a utility and planting strip width of 10 feet
around the entire cul-de-sac. The center point for the radius shall
be on the center line of the associated street or, if offset, offset
to a point where the radius becomes tangent to the right curbline
of the associated street. (See Plate 3.)
(9) No street shall have a name which will duplicate or
so nearly duplicate the name of an existing street that confusion
results. The continuation of an existing street shall have the same
name. Curvilinear streets shall change their names only at street
intersections. The Board shall reserve the right to approve or name
streets within a proposed development.
(10)
The pavement width of streets and the quality
of surfacing and base materials shall adhere to the minimum standards
set forth by the Township, county or state engineers when said paving
concerns roads under the jurisdiction and where such standards exist.
Concerning streets under the jurisdiction of the Township, the following
standards shall apply:
(a)
The minimum requirements of any new street shall
be constructed according to the specifications and procedures as set
forth in the New Jersey State Highway Department of Transportation
specifications, as amended.
(b)
Subgrade. Where fill is required, the underlying
ground surface shall be stripped of all brush and trees before filling
is commenced. The material used for fill shall be suitable therefor
and shall be free from any matter that may decay. The fill shall be
formed in successive layers and each layer compacted by operating
the construction equipment over it until it is firm and unyielding
before the next layer is placed. Before construction of the gravel
base is commenced, the subgrade shall be neatly dressed to the proper
lines, grades and cross sections. If, during plan review or construction,
the Township Engineer determines that underdrains or subbase outlet
drains are necessary for subsoil drainage, the developer/subdivider
shall have said systems designed by a professional engineer and installed,
all in accordance with Division 5, Section 1 of the New Jersey State
Highway Department Standard Specifications for Road and Bridge Construction,
latest revision. The plans for these systems and their construction
shall be approved by the Township Engineer.
[1]
The pavement foundation shall consist of six
inches of compacted gravel and three inches of bituminous stabilized
base. The gravel base course may require a prime coat of asphaltic
oil, if so directed by the Township Engineer. The bituminous stabilized
base course will require a tack coat of asphaltic oil.
[2]
The gravel base course shall consist of six
inches of compacted road gravel, Type 2, Class A or B (Soil Aggregate
I-5), conforming to the requirements of the New Jersey State Highway
Department Standard Specifications. The finished subbase shall be
thoroughly compacted and bound together, hard, smooth and even, free
from defects and at the proper grade and contour.
[3]
The bituminous stabilized base course shall
comply with the requirements of Division 3, Section 2.A of the New
Jersey State Highway Department Standard Specifications, latest revision.
(c)
On all Township collector and arterial streets,
as defined in the traffic and circulation section of the Land Use
Development plan, the base course shall be eight inches.
(d)
No street shall have a paved cartway of less
than 30 feet, except that in the R-6 and HR Districts, the minimum
paved cartway shall be not less than 36 feet wide.
(e)
Streets shall be permanently paved with two-inch-thick
bituminous concrete pavement, Type FABC-1, Mix I-5. The pavement shall
be constructed in accordance with the requirements of the New Jersey
State Highway Department Standard Specifications, latest revision.
(11)
The approval of any map of land delineating
streets by the governing body of the Township shall in no way be construed
as an acceptance of any street indicated thereon.
B. Curbs. Concrete curbing shall be installed along every
street and at intersections with existing Township, county or state
roads and shall be laid in a manner approved by the Township Engineer.
The curbing shall meet the following specifications:
(1) The concrete to be used for curbs shall be Class B
concrete as specified in the New Jersey Highway Specifications for
Curbs and Gutters.
(2) Expansion joints shall be provided at intervals of
20 feet and shall be sealed as specified by the Township Engineer.
(3) Openings for driveways shall be four feet wider than
the width of the driveway it serves. The curb at such driveway openings
shall be depressed to the extent that 1 1/2 inches extends above
the finished pavement. The rear top corner of this curb shall have
a radius of 1/4 inch and the front top corner shall have a radius
of 1 1/2 inches.
(4) Concrete curbs for secondary and primary local roads
shall be eight inches wide at their base and not less than six inches
wide at their top. Their height shall not be less than 18 inches and
be constructed to show a vertical face above the roadway pavement
of six inches. The rear top corner of this curb shall have a radius
of one-fourth-inch, and the front top corner shall have a radius of
1 1/2 inches. (See Plate 4.)
(5) Rolled curbs may be permitted to service detached
single-family developments if the applicant can show the Planning
Board that there will be no adverse effects from the use of rolled
curbs.
C. Sidewalks.
(1) Sidewalks shall be required on both sides of all streets
serving a collector function as stipulated in the adopted Master Plan
and/or Official Map of the Township and on local residential streets
as required by the Board. Sidewalks in nonresidential developments
shall be required, at the Board's discretion, depending upon the probable
volume of pedestrian traffic, the development's location in relation
to other populated areas, and the general type of improvement intended.
(2) Where required, sidewalks shall be at least four feet
wide and located as approved by the Board. Sidewalks shall be concrete
or an equivalent approved by the Board and shall be constructed in
accordance with Division 5 of the specifications of the New Jersey
State Highway Department.
D. Trees. Street trees should be planted at intervals depending on their types. Along all public rights-of-way, shade trees having a caliper at planting of at least 1 1/2 inches shall be planted 30 feet to 40 feet apart and otherwise conform to §
400-48C.
Street furniture includes the man-made elements
of a municipal landscape such as phone booths, benches, planting boxes,
mail and meter boxes, water towers, lighting standards, directional
signs, fire hydrants, power lines, fences and walls, water fountains
and pools, drinking fountains, trash receptacles, bike racks, sculpture,
paving and steps and bus shelters.
A. Certain street furniture is functional in nature and
should be located where the demand is. Bike racks should be located
near recreational activities and commercial establishments.
B. Bus shelters should be required at least at major
intersections where bus service exists or is anticipated. It is desirable
to provide indentations to accommodate the buses off the main travelled
routes. The shelters should be designed to keep rain off those waiting
for the buses and to break the wind. They should be entirely enclosed
but designed to allow the interiors to be readily observed.
C. Trash receptacles should be located near recreational
activities, at street corners, at entrances and exits to buildings,
and where people naturally congregate. Open-weave receptacles should
be avoided because the wind blows small bits of paper and debris from
them.