The following principles of subdivision and land development,
general requirements, and minimum standards of design shall be observed
by the applicant in all instances.
A. All portions of a tract being subdivided shall be taken up in lots,
streets, public lands or other proposed uses so that remnants and
landlocked areas shall not be created.
B. When only a portion of a tract is being reviewed relative to subdivision
and land development, but where future subdivision or development
is imminent, the applicant shall demonstrate that the remainder of
the tract or parcel may be subdivided or developed in conformance
with the existing zoning classification of land use in a logical and
satisfactory manner as a condition of approval of his plan.
C. Whenever possible, applicants shall preserve trees, groves, waterways,
scenic points, historic spots and other community assets and landmarks.
D. Subdivisions and land developments should be laid out so as to avoid
the necessity for excessive cut or fill unless specifically warranted
by terrain or location.
E. Floodplain areas shall not be subdivided or developed except in strict compliance with the standards and requirements of Chapter
156, §
156-2, of this Code.
F. The standards included in this chapter are minimum design requirements.
However, the Board of Commissioners reserves the right in any case
to increase the same if conditions so warrant.
G. Modifications.
(1) The Board of Commissioners may grant a modification of the requirements
of one or more provisions of this chapter if the literal enforcement
will exact undue hardship because of peculiar conditions pertaining
to the land in question, provided that such modification will not
be contrary to the public interest and that the purpose and intent
of this chapter is observed or when the applicant demonstrates that
proposed alternative standard to a requirement that is set forth in
this chapter would provide equal or better results in furtherance
of the purpose and intent of this chapter.
(2) All requests for a modification shall be in writing and shall accompany
and be a part of the application for development. The request shall
state in full the grounds and facts of unreasonableness or hardship
on which the request is based, the provision or provisions of the
ordinance involved and the minimum modification necessary. In the
case of a proposed alternative standard, the applicant shall submit
sufficient data, as required by the Township Engineer, to demonstrate
that the alternative standard would provide equal or better results
to that of the required standard under this chapter.
(3) The request for modification may be referred to the Advisory Planning
Agency for advisory comments.
(4) The Board of Commissioners shall keep a written record of all action
on all requests for modifications.
H. Where no public water supply is available to the subdivision or land
development, the Board of Commissioners shall require the subdivider,
developer or builder to obtain from the district sanitarian of the
Department of Environmental Protection certificates of approval as
to the quality and adequacy of the water supply proposed to be utilized
by the subdivider, developer or builder and approval of the type and
construction methods to be employed in the installation of the individual
water supply system, in accordance with current state regulations.
I. Where the subdivision or land development is inaccessible to sanitary
sewers, the Board of Commissioners shall require the subdivider, developer
or builder to obtain from the district sanitarian of the Department
of Environmental Protection certificates of approval of the sewage
disposal facilities to be provided by the subdivider, developer or
builder, in accordance with current state regulations.
J. Applicants shall observe the ultimate rights-of-way for contiguous
existing streets as prescribed by the Comprehensive Plan for the Township.
Additional portions of the corridors for such streets shall be offered
to the government agency having jurisdiction at the time the subdivision
or land development is consummated. Applicable building setback lines,
as defined by the Township Zoning Ordinance of current adoption, shall
be delineated as measured from the ultimate right-of-way.
K. Proposed subdivision and land development shall be coordinated with
the existing nearby neighborhood so that the community as a whole
may develop harmoniously.
L. Areas provided or reserved for such community facilities shall be
adequate to provide for building sites, landscaping and off-street
parking as appropriate to the use proposed. The Board of Commissioners
reserves the right to accept or refuse offers of dedication for public
use.
M. Improvement construction requirements shall be completed under the
Engineering and Construction Standards of Upper Moreland Township,
the specifications of the Pennsylvania Department of Transportation,
Department of Environmental Protection, the Montgomery County Conservation
District or other appropriate agencies, or the specifications included
herein, whichever specifications shall result in the more favorable
interpretation of this provision.
N. Construction of facilities. The subdivider, developer or builder
shall, where specified by the Board of Commissioners, construct and
install with no expense to the Township the streets, curbs, sidewalks,
water mains, sanitary and storm sewers, streetlights, fire hydrants,
street signs, shade trees, monuments, and other facilities and utilities
specified in this article. Construction and installation of such facilities
and utilities shall be subject to inspection by appropriate Township
officials during the progress of the work, and the subdivider shall
pay for inspection.
All new streets and widened portions of all existing rights-of-way,
intended for public use shall be dedicated to the Township, subject
to final acceptance based on compliance with the following requirements.
A. Street system.
(1) Conformance with adopted plans. The proposed street pattern shall
be properly related to existing streets, to the Township Plan of Streets,
and to such county and state road and highway plans as have been duly
adopted by the respective agency.
(2) Arrangement. Streets shall be arranged in a manner to meet with the
approval of the Board of Commissioners, considered in relation to
both existing and planned streets, and located so as to allow proper
development of surrounding properties. Secondary and through highways
shall be connected with such existing streets and highways so as to
form continuations thereof. Residential streets shall be laid out
to discourage their use as secondary streets or through highways.
(3) Conformity with topography. Streets shall be adjusted to the contour
of the land so as to produce usable lots and streets of reasonable
grade, alignment and drainage.
(4) Grading. The street shall be graded to the full width of the right-of-way
and provision made for slopes beyond the right-of-way in conformance
with the applicable standards.
(5) Provisions of streets for future development. Access shall be given
to all lots and portions of the tract in the subdivision and to adjacent
unsubdivided territory. Streets giving such access shall be improved
to the limits of the subdivision. Remnants, reserve strips and landlocked
areas shall not be created.
(6) New streets. New streets shall be laid out to continue existing streets
at equal or greater right-of-way and cartway width, where practical.
(7) Dead-end streets. Dead-end streets are prohibited, unless designed
as culs-de-sac or designed for access exclusively to neighboring tracts.
(8) Street names and signs. No street names shall be used which will
duplicate or be confused with the name of an existing street. All
street names are subject to the approval of the Board of Commissioners.
Existing street names shall be projected whenever possible. Signposts
and nameplates, approved by the Township, shall be placed at street
intersections at the cost of the developer.
(9) Obstructions. No fences, trees, hedges, walls, plantings or other
obstructions shall be located within, or be permitted to grow into,
the right-of-way.
(10)
Half street. The dedication of half streets at the edges of
a new subdivision is prohibited. If circumstances render this impracticable,
adequate provision for the concurrent dedication of the remaining
half of the street must be furnished by the subdivider, developer
or builder. When there exists a half street in an adjoining subdivision,
the remaining half shall be provided by the proposed development.
B. Right-of-way width, paving width and curbing.
(1) Classification.
[Amended 9-12-2011 by Ord. No. 1602]
(a)
All streets shall be classified as primary, secondary or residential.
The following list identifies all primary and secondary streets within
the Township:
[1]
Primary streets: County Line Road (S.R. 2038), Easton Road (S.R.
0611), Moreland Road (S.R. 0063) and York Road (S.R. 0263).
[2]
Secondary streets: Blair Mill Road, Byberry Road, Commerce Avenue,
Computer Avenue, Davisville Road, Edge Hill Road, Fitzwatertown Road,
Horsham Road, Huntingdon Road, Maryland Road, Masons Mill Road, Mill
Road, Pioneer Road, Terwood Road, Turnpike Drive, Warminster Road,
West Moreland Avenue, Wyandotte Road and any other nonresidential
street.
[3]
Residential streets: all streets not listed above within a residential
zoning district.
(b)
All streets shall be governed as follows:
[1]
Residential streets shall be those which are used strictly to
serve residential areas and do not serve as through streets in a development.
They shall have a minimum right-of-way width of 50 feet and shall
have a minimum paved width of 30 feet. Construction of the street,
curbing and sidewalk shall be in accordance with the Standards.
[2]
Secondary streets shall have a minimum right-of-way of 60 feet
and shall have a minimum paved width of 40 feet. Curbing and/or sidewalks
shall be provided as required. Construction shall be in accordance
with the Standards.
[3]
Primary streets shall have a minimum right-of-way of 100 feet
and shall have a minimum paved width of 52 feet, shoulders or curbing
and/or sidewalk, appropriate median, widening at intersections for
turning lanes, channelization, etc., in accordance with the Standards.
Construction shall be in accordance with the Standards.
[4]
Cul-de-sac streets.
[a] The length shall not be more than 500 feet, unless
special conditions submitted by the applicant warrant approval by
the Board of Commissioners.
[b] For residential streets, the minimum right-of-way
shall be 50 feet, a paved width of 30 feet, a circular turnaround
with a minimum right-of-way radius of 60 feet and an outer paved radius
of 50 feet.
[c] For streets other than residential, the minimum
right-of-way shall be 60 feet, a paved width of 40 feet, a circular
turnaround with a minimum right-of-way radius of 60 feet and an outer
paved radius of 50 feet.
[d] Construction shall be in accordance with the Standards.
[e] Temporary culs-de-sac are those culs-de-sac constructed
to an abutting property line with the intention that such road will
be extended onto the adjoining property at a future date as a logical
step in the circulation network of neighborhood, superblock or area.
Temporary culs-de-sac shall be required by the Board when conditions
so warrant. Temporary culs-de-sac shall be governed by the same design
standards as permanent culs-de-sac.
C. Street width. The following general standards shall apply to street
width:
(1) The minimum widths of the right-of-way and paving and the requirements
for curbing shall not be less than those of an existing street of
which the new street is to be a continuation, no less than as required
above under classification.
(2) Ultimate rights-of-way and setbacks. Subdivision of lots along residential
streets of insufficient width shall either effect a widening to provide
a width from center line to side line of right-of-way of 25 feet,
or shall establish an ultimate right-of-way line at least 25 feet
from the street center line, or shall correspond with the ultimate
right-of-way for these streets as defined on the Township Comprehensive
Plan.
(3) The area between an existing right-of-way line and the ultimate right-of-way
line shall be offered for dedication to the authority having jurisdiction
over the road when land is subdivided or developed along an existing
right-of-way.
(4) Islands, medial strips, channelization may be required in any area
where traffic volumes warrant their use for safety and efficiency,
and may be permitted in any area at the discretion of the Board of
Commissioners.
(5) Additional width requirements. Additional widths may be required
by the Township.
(a)
Where necessary for public safety and convenience.
(b)
For parking in commercial or industrial areas.
(c)
Where old roads do not provide the proper width and additional
dedication is necessary.
(6) No fences, hedges, trees, shrubbery, walls, plantings or other obstructions
shall be located or be permitted within the right-of-way except for
ground covers such as grass, ivy, crown-vetch, or horizontally spreading
shrubs less than one foot high, or retaining walls necessitated by
road widening and constructed by the authority having jurisdiction
over the road.
(7) Where there are present streets, the Board of Commissioners may grant
such reasonable exceptions to the requirements for grading and width
of cartway provided for in this chapter as will not be contrary to
the public interest, subject to conditions necessary to assure adequate
streets and other public improvements.
(8) The setbacks contemplated in the Zoning Ordinance shall be measured from such ultimate right-of-way line.
In the case of commercial, industrial or secondary streets, the setback
lines shall be measured from a point 30 feet from the center line
of the street or road upon which the lot abuts. Where the subdivision
or land development is along a state or county highway right-of-way,
the setback lines shall be measured from the right-of-way line, provided
it is at a greater distance from the center line than required by
the Township Comprehensive Plan.
D. Alleys. Alleys are prohibited in residential developments. In commercial
or industrial districts without expressly designed loading areas,
alleys with a minimum width of 25 feet may be required. Where such
alleys dead end, they shall be provided with a turnaround having a
radius of not less than 40 feet. The cartway shall be a minimum of
20 feet.
(1) Paving. The paving requirements shall be the same as for street paving.
(2) Intersections of right-of-way lines shall be rounded by a tangential
arc, the minimum radius of which shall be 10 feet, and the edge of
the paving at intersections shall be rounded by a tangential arc,
the minimum radius of which shall be 20 feet.
(3) Obstructions. No fences, hedges, trees, shrubbery, walls, plantings
or other obstructions shall be located within the right-of-way. Reasonable
sight distance shall be provided at intersections with streets.
E. Alignment.
(1) Vertical curves. Vertical curves shall be used at changes in grade
of more than 1%. The length of curve shall be dependent on the sight
distance. The sight distance will be measured along the center line,
and shall be 600 feet for primary roads; 400 feet for secondary roads;
and 200 feet for local residential streets, in accordance with A Policy
of Geometric Design of Rural Highways by the American Association
of State Highway Officials.
(2) Horizontal curves shall be used at all changes in excess of 2°.
Long radius curves shall be used rather than a series of curves connected
by short tangents. Minimum radius curves at the end of long tangents
will not be approved.
(a)
Curvature. The minimum radius at the center line for horizontal
curves on primary streets shall be 300 feet; for secondary streets,
200 feet; and for residential streets, 150 feet.
(b)
Tangents between curves. All streets shall have a tangent of
at least 100 feet, measured at the center line, between reverse curves.
(3) Street grades.
(a)
There shall be a minimum grade of at least 0.75% on all streets.
(b)
Maximum grades. A maximum grade of 7% on primary and secondary
streets and 10% on residential streets for distances of not more than
1,500 feet. However, grades in excess of 5% shall be avoided wherever
possible. The grade shall be measured along the center line.
(c)
Curve-grade combinations. A combination of minimum radius horizontal
curves and maximum grades will not be approved.
(d)
Street intersections. The grade within 100 feet of any side
of an intersection or the outer perimeter of a cul-de-sac shall not
exceed 3%. The grade will be measured along the curbline of the street.
F. Street intersections.
(1) Number of intersections. No more than two streets shall cross at
the same point. Four-way intersections are to be avoided in the layout
when three-way or T intersections can be utilized. When existing streets
intersect at odd angles or have more than four approaches, the subdivider,
developer or builder shall be required to make corrective changes
to eliminate the odd angle or reduce the number of approaches to the
intersection by curing the lesser street.
(2) Minimum angle of intersection. Right angle of intersections shall
be used whenever practicable, especially when local streets empty
into major or secondary streets; there shall be no intersection angle,
measured at the center line, of less than 60° minimum.
(3) Center line. Where center lines of residential or secondary streets
open into opposite sides of a major street within 100 feet of each
other, they shall be made to coincide by curing the minor street or
streets.
(4) Primary thoroughfare. Wherever practicable, intersections with secondary
or primary highways shall be kept to a minimum and shall be located
at least 800 feet apart.
(5) Sight distance. There shall be measured along the center line a minimum
clear sight triangle of 75 feet from the point of intersection. No
building, trees, hedge, shrubbery or other obstruction whatsoever
will be permitted in this area. Any obstruction to sight shall be
removed at the time a building or structure is erected, whichever
shall first occur.
(6) Approach grades. All approaches to an intersection shall not exceed
3% for a distance of 100 feet measured from the nearest right-of-way
line of the intersecting street. Vertical curves shall be used for
changes of grade of more than 1%.
(7) Radii of pavement and right-of-way at intersections. Street intersections
shall be rounded with tangential arcs at pavement edge (curbline)
and right-of-way lines as listed below. Where two streets of different
right-of-way widths intersect, the radii of curvature for the widest
street shall apply.
|
Type of Street
|
Minimum Radius of Arc at Intersection of Pavement Edge
or Curb Line
(feet)
|
Minimum Radius of Arc at Intersection of Right-of-Way
Line
(feet)
|
---|
|
Primary
|
40 (or more as may be required)
|
20
|
|
Secondary
|
35
|
25
|
|
Residential
|
25
|
15
|
G. Street paving. All street paving must conform to the Standards of
Upper Moreland Township and be approved by the Township Engineer prior to acceptance
by the Board. All grades, horizontal curves, vertical curves, intersections,
sight distances, and tangents shall conform to the requirements established
by this chapter and shall be subject to the approval of the Township
Engineer.
H. Private streets or roadways. When permitted by the Board of Commissioners,
in the R or R-1 Residential Districts, following review by the Township
Engineer and Advisory Planning Agency, roadways serving as private
streets or roadways shall be developed in accordance with the following
standards:
(1) Any plan proposing the use of a private street or roadway shall have
a note placed on the plan stating that such private street or roadway
shall not be dedicated to the Township and the Township will not assume
any responsibility for maintenance or snowplowing of such private
street or roadway.
(2) Roadways serving as private streets shall conform to the minimum
design standards for public streets, including ultimate right-of-way,
with the exception of curbing, sidewalks, shoulder grading and width
of cartway requirements. In no case, however, shall the width of pavement
be less than 20 feet.
(3) Roadways serving as private streets shall make provisions for drainage
and stormwater runoff in accordance with the review and approval of
the Township Engineer.
(4) The Board of Commissioners, with the advice of the Advisory Planning
Agency and the Township Engineer, shall evaluate the location, placement
and alignment of roadways serving as private streets based upon the
ease of accessibility to and efficient maneuverability for protective
fire, police and emergency services.
(5) The owner or owners and all successors of any property or properties
which abut roadways serving as a private street shall be fully responsible,
either singly or jointly, for the permanent improvement of the roadway
and for the maintenance thereof in a good, safe and passable condition.
An agreement, to be approved by the Township Solicitor, to provide
for such maintenance responsibilities shall be recorded with the development
plan.
I. Trench
backfill outside of public right-of-way. Trench backfill outside of
the public right-of-way, including paved and unpaved areas, must utilize
suitable backfill material compacted to 95% in uniform layers not
exceeding 12 inches. Suitable backfill material includes stone, suitable
soils or other materials as approved by the Township Engineer. Backfill
above underground basins and in other areas deemed necessary by the
Township Engineer must be full stone backfill. If on-site soils are
utilized, then compaction test results must be provided during construction.
[Added 9-12-2011 by Ord. No. 1602]
J. Trench
backfill in public streets. Full stone backfill with 2A modified stone,
compacted to 95% in uniform layers not exceeding 12 inches, shall
be required for trench restoration within the public right-of-way.
[Added 9-12-2011 by Ord. No. 1602]
No subdivision of land will be approved with the property line
extending through any portions of any existing structure.
A. If structure(s) is to remain.
(1) In residential zoning districts of the Township, the lot size and
the lot dimensions of the newly created lot containing the structure(s)
must be in scale with the height and bulk of the structure even if
this requires a lot area and/or dimensions exceeding the minimum zoning
requirement for that district. Structures proposed on the vacant portions
of lands being subdivided shall conform to the extent possible with
the height, bulk, building materials and architectural character of
the existing structures in the immediate vicinity, and the subdivision
plans shall show building plans at suitable detail.
(2) In other zoning districts of the Township (especially commercial
and industrial districts), the subdivision of the land must provide
adequate service and parking facilities, etc., in keeping with the
minimum requirements of the Zoning Ordinance for each lot and cumulatively
for all lots in the subdivision. No subdivision will be approved in
such instances if the servicing and/or parking facilities, etc., attendant
to the existing structure are deemed inadequate or would be considered
to become inadequate with the development of the now vacant lands.
Any new structures contemplated on the newly subdivided parcels shall
be in conformity with the existing structures in the immediate vicinity
to the extent possible in regards to height, bulk, building material
and architectural character, and the subdivision plans shall show
building plans at suitable detail.
(3) Alterations and replacements will be permitted within the existing
structure, but exterior extensions of the building must conform to
the requirements of the Upper Moreland Township Zoning Ordinance.
(See Ch.
287, Stormwater Management.)
[Amended 11-10-2008 by Ord. No. 1566]
A. Whenever the vegetation and topography are to be disturbed, such activity must be in conformance with Title 25, Rules and Regulations, Part I, Commonwealth of Pennsylvania, Department of Environmental Protection, Subpart C, Protection of Natural Resources, Article
II, Water Resources, Chapter 102, Erosion Control, and in accordance with the Montgomery County Conservation District.
B. Additional erosion and sedimentation control design standards and
criteria that must be applied where infiltration BMPs are proposed
shall include the following:
(1) Areas proposed for infiltration BMPs shall be protected from sedimentation
and compaction during the construction phase, so as to maintain their
maximum infiltration capacity.
(2) Infiltration BMPs shall not be constructed nor receive runoff until
the entire contributory drainage area to the infiltration BMP has
received final stabilization.
Limit of contract. Where the applicant is offering for dedication
or is required by ordinance to establish a reservation of open space
or preserve an area of scenic or historic importance, a "limit of
contract" which will confine excavation, earthmoving procedures and
other changes to the landscape will be required to ensure preservation
and prevent destruction of the character of the area in open space.
[Amended 2-4-2008 by Ord. No. 1555]
A. Reserve strips controlling access to streets, subdivisions or adjacent
areas are prohibited.
B. Right-of-way for streets shall be required as needed, the location
and width in each case to be determined by the Board of Commissioners.
(1) Building setback lines shall be measured from the nearest side of
the ultimate right-of-way of a street to the proposed building.
(2) Nothing shall be permitted to be placed, planted, set or put within
the area of a right-of-way for a street. The area shall be kept as
lawn with the exception of mailboxes.
(3) The owner of any lot, upon written request by the Township, and at
the owner's sole expense, shall remove anything placed, planted,
set or put (with or without knowledge of this regulation) within the
area of any right-of-way of a street.
C. Easements for sanitary utilities, drainage purposes, public utilities,
or for any specific purpose shall be required as needed, the location
and width in each case to be as determined by the Board of Commissioners.
(1) Building setback lines shall be five feet from the nearest side of
the easement to the proposed building.
(2) Nothing shall be permitted to be placed, planted, set or put within
the area of an easement. The area shall be kept as lawn.
(3) The owner of any lot, upon written request by the Township, and at
the owner's sole expense, shall remove anything placed, planted,
set or put (with or without knowledge of this regulation) within the
area of any easement.
(4) To the fullest extent possible easements shall be adjacent to rear
or side lot lines.
D. No right-of-way for a street nor an easement for any purpose whatsoever
shall be recited or described in any deed unless the same has been
shown on an approved plan. Any error found in a deed shall be immediately
corrected and rerecorded in the Office of the Recorder of Deeds for
Montgomery County at Norristown, Pennsylvania, at the sole expense
of the subdivider.
E. Easements. Easements for present or ultimate construction of storm
drains and sanitary sewers having a minimum width of 20 feet shall
be provided where necessitated by topographic conditions. Where a
subdivision or land development is traversed by a natural watercourse,
there shall be provided a drainage easement of right-of-way conforming
substantially with the line of such watercourse and of such widths
as will be adequate to preserve natural drainage.