[Ord. 1631, 8/14/2000, Section I]
To establish lighting standards for public safety and welfare
while minimizing the adverse effects of outdoor lighting, such as
glare.
To protect the privacy of residents and prevent the creation
of nuisances caused by unnecessary intensity and glare of outdoor
lighting onto neighboring properties, public streets, and into the
night sky;
To promote lighting practices and systems that will enhance
the safety and enjoyment of pedestrians, bicyclists, motorists, and
neighboring properties, and which conserve energy without decreasing
safety;
To encourage the selection of lighting fixtures to be complementary
and sensitive to historic structures; and
To prohibit outdoor lighting installations which are of excessive
intensity and/or are deficient of photometric control such that the
resulting glare and light trespass create a nuisance to pedestrians,
cyclists, or motorists on neighboring properties and roadways.
[Ord. 1631, 8/14/2000, Section II]
The requirements of this chapter apply to the design, installation,
and continued operation of outdoor luminaires and lighting systems
as specified herein that are newly designed, constructed, erected,
installed, or placed into operation after the effective date of this
ordinance.
[Ord. 1631, 8/14/2000, Section III]
Outdoor luminaires and lighting systems existing prior to the
effective date of this ordinance are protected and may continue as
nonconforming structures or uses. When nonconforming luminaires are
replaced with new luminaires or when nonconforming lighting systems
are expanded or extended, such replacement, expansion or extension
shall be done in accordance with all applicable provisions of this
chapter. Nonconforming luminaires and lighting systems may be maintained
and repaired. Maintenance and repair means:
[Ord. 1631, 8/14/2000, Section IV]
Zoning permits are required prior to the installation of new outdoor luminaires or lighting systems only when prescribed under Section 2706 of this chapter Part. When a zoning permit is not required prior to the installation of an outdoor luminaire or lighting system, all other applicable provisions of this ordinance remain in force.
[Ord. 1631, 8/14/2000, Section V]
a.
The regulations of this ordinance apply only to those lighting installations as specified in Section 2706.
b.
Federal- and state-required security lighting and air travel safety
lighting are exempted from the provisions of this ordinance.
c.
Temporary holiday and special event lighting is exempted from the
provisions of this ordinance. However, non-cutoff luminares shall
not exceed 2,300 lumens and shall be situated to prevent glare and
light trespass. All flood or spotlights shall be directed away from
adjacent properties and roadways.
d.
Luminaires in place prior to the adoption of this ordinance that
pose a safety hazard to pedestrian or vehicular traffic shall be shielded
or redirected to eliminate the hazard.
[Ord. 1631, 8/14/2000, Section VI.a-h.; amended by Ord. 1682,
10/15/2001, Section 1; Ord. 1709, 10/15/2002, Section 11; Ord. 1781,
5/24/2004, Sections 1 and 2.; Ord. 1823, 11/9/2005, Section 1]
These regulations apply to the following specific outdoor lighting
installations:
a.
Outdoor Area Lighting Requirements.
(1)
Applicability. The requirements specified in this chapter Part apply
to outdoor lighting installations used for nighttime area illumination
of car sale areas, convenience store parking areas, gasoline service
station parking areas, and pump islands not under canopy and to parking
areas, driveways, yards, and other similar areas illuminated on any
property including parks except for those installations made at one-
and two-family dwellings.
(2)
Cutoff Luminaires Required. All luminaires used in outdoor area lighting
installations shall be a cutoff luminaire type that complies with
the following standards:
(a)
The candlepower distribution classification of the luminaire
as a cutoff type shall be in accordance with the ANSI/IES lighting
definitions and the IES Lighting Handbook. The manufacturer of the
luminaire shall provide certification of the cutoff classification
based on photometric testing performed in accordance with the IES
Lighting Handbook and the applicable testing procedures referenced
therein. The requirement for the use of cutoff luminaire types shall
include, but not be limited to, the following outdoor area lighting
configurations: (1) Pole-mounted luminaires, (2) luminaires mounted
on the exterior of buildings and structures, (3) luminaires mounted
on or within exterior canopies of buildings or in free standing canopies,
and (4) pedestal or bollard-mounted luminaires.
(b)
Cutoff luminaires shall be mounted and maintained plumb and
level in accordance with the intended application of their design.
For the purposes of this requirement, the photometric nadir of the
luminaire (zero degree vertical angle of the candlepower distribution)
shall be oriented plumb, and the vertical angle of 90° above nadir
(horizontal) shall be oriented level. Cutoff luminaires shall not
be installed or subsequently placed in a canted or titled position
that permits candlepower distribution above the horizontal.
(c)
Exception for Alternative Technology. Luminaires that do not
meet the definition for cutoff luminaire, yet employ alternative technology
that causes the photometric performance to approach that of cutoff
luminaires, may be approved on a case-by-case basis. Such luminaires
include, but are not limited to, period-style luminaires with refractive
globes and internal cutoff reflectors.
(d)
Exception for Period-Style Luminaires in all Outdoor Area Lighting
Applications, Except for Parks. An area that reflects a particular
historical period or architectural style may use non-cutoff luminaire
installations provided that all of the following are met: (1) The
exterior appearance of the fixtures and posts shall reflect the historic
period or architectural style of the area; (2) the maximum initial
illuminance level of any non-cutoff luminaire shall not exceed 2,300
lumens; and (3) no luminaire shall be mounted higher than 15 feet
above grade.
(e)
Exception for Period Style Luminaires in Parks. Non-cutoff luminaire
installations are permitted in park applications provided all of the
following are met: (1) Style of lighting fixtures and posts shall
be vintage or architectural or historic; (2) the maximum initial illuminance
level of any non-cutoff luminaire shall not exceed 9,500 lumens; and
(3) no luminaire shall be mounted higher than 15 feet above grade.
(3)
Maximum Illuminance Levels at Property Lines. The maximum maintained
illuminance levels permitted at the property line(s) during the nighttime
produced by the sum of all outdoor lighting installations on said
property shall be measured at grade in Horizontal Footcandles and
in accordance with the requirements in Table 1 for the zoning district
in which the property is located.
(4)
Luminaire Height. The maximum height of luminaires in outdoor area
installations shall be in accordance with the requirements in Table
1 for the zoning district in which the property is located. [Table
1 is at the end of this chapter Part.]
(5)
Lighting Plan and Zoning Permit Required. An approved lighting plan and zoning permit are required prior to the installation of any outdoor area lighting application as described in this chapter Part. All lighting plans shall be prepared and submitted to the municipality in accordance with the provisions of Section 2709 of this chapter. The zoning permit shall not be issued until the lighting plan is approved by the municipality.
b.
Outdoor Canopy Lighting Requirements:
(1)
Applicability. The requirements specified in this chapter Part applies to outdoor lighting installations that illuminate the area under outdoor canopies except for those installations made at one- and two-family dwellings. Lighting levels under canopies should be adequate to facilitate the activities taking place, but lighting itself should not be used to attract attention to a business. Signs as allowed under the Sign Ordinance shall be used for that purpose. (Note: Illuminated transparent and translucent surfaces of back-lit canopies constitute signs and the area thereon is regulated by the Sign Ordinance, Chapter XV, Section 111).
(2)
Canopies. Outdoor canopies include, but are not limited to, the following
applications: (1) all canopies associated with service stations and
convenience stores, (2) canopies over store and office fronts, (3)
all marquees and projecting overhangs, (4) exterior canopies over
driveways and building entrances, and (5) pavilions and gazebos.
(3)
Cutoff Luminaires Required. All luminaires used to illuminate canopies
and the area below shall be cutoff luminaires that comply with Section
2706.a(2) of this chapter.
(4)
Maintained Average Illuminance. The maintained average illuminance
on grade level surfaces below canopies shall not exceed 30 footcandles
for applications in nonresidential zoning districts and shall not
exceed 10 footcandles in residential zoning districts.
(5)
Maximum Illuminance Level at Property Lines. The maximum maintained illuminance levels permitted at the property line(s) during the nighttime produced by the sum of all outdoor lighting installations on said property shall be measured at grade in Horizontal Footcandles according to Table 1 for the zoning district in which the property is located. [Table 1 is at the end of this chapter Part.] Exception: The maximum illuminance level measured at the property line is not applicable to canopys built over the property line pursuant to the Section 205 of Chapter XV. However, all other requirements pertaining to cutoff luminaires as specified in this chapter Part apply.
(6)
Lighting Plan and Zoning Permit Required. An approved lighting plan and zoning permit are required prior to the installation of any outdoor area lighting application as described in this chapter Part. All lighting plans shall be prepared and submitted to the municipality in accordance with the provisions of Section 2709 of this chapter. The zoning permit shall not be issued until the lighting plan is approved by the municipality.
c.
Exterior Display and Sales Area Lighting Requirements.
(1)
Applicability. The requirements of this chapter Part apply to commercial
and industrial uses where exterior display or sales areas are located
on portions of the property beyond parking areas, canopies, or pump
islands.
(2)
Maintained Average Illuminance. The maintained average illumination
on grade level surfaces where exterior display and sales areas are
located on portions of the property beyond parking areas, canopies,
or pump islands shall not exceed 5.0 footcandles.
(3)
Cutoff Luminaires Required. All luminaires used to illuminate exterior
display and sales areas shall be cut-off luminaires that comply with
Section 2706.a(2) of this chapter. Luminaire height and the maximum
permitted illumance at the property line shall not exceed that permitted
in the zoning district as specified in Table 1. [Table 1 is at the
end of this chapter Part.]
(4)
Lighting Plan and Zoning Permit Required. An approved lighting plan and zoning permit are required prior to the installation of any outdoor area lighting application as described in this chapter Part. All lighting plans shall be prepared and submitted to the municipality in accordance with the provisions of Section 2709 of this chapter. The zoning permit shall not be issued until the lighting plan is approved by the municipality.
d.
Outdoor Facility and Event Lighting Requirements.
(1)
Applicability. The requirements specified in this chapter Part apply
to all outdoor lighting installations, including those at one- and
two-family dwellings, used for nighttime area illumination of sports,
cultural, and recreational facilities, or events. Outdoor facility
lighting includes, but is not limited to the following installations:
ball fields, ballparks, stadiums, tennis courts, soccer fields, golf
courses, driving ranges, recreational fields, amphitheaters, etc.
(2)
Cutoff Luminaires. Only cutoff luminaires shall be used to illuminate
areas beyond the play field, stage, or other surface upon which the
event actually occurs.
(3)
Non-Cutoff Luminaires. Outdoor facilities for sports, cultural, and
recreational events have unique lighting needs that vary depending
on the nature of the activity and size of the facility. Because of
their uniqueness, the actual playing or performance areas cannot be
illuminated appropriately using cutoff luminaires. Accordingly, non-cutoff
luminaires such as floodlights and other applications, are permitted
to meet the lighting design objectives for outdoor facility and event
lighting provided such luminaires are equipped with glare shields,
visors, barn doors, or other shielding to meet the following criteria:
(a)
The candlepower distribution from all lighting installations
shall be cut off at and above the horizontal level.
(b)
To the extent practicable, the candlepower distribution from
all lighting installations shall be farther cut off at angles below
the horizontal level to restrict illumination to within the functional
area being illuminated for sports, cultural, or recreational purposes.
(4)
Lights Out. The primary light source (e.g., spotlights or floodlights)
for all activities shall be turned off within 60 minutes following
the end of the event. Exception: The track
facility at the State College Area High School, South Campus shall
be regulated as follows:
[Amended by Ord. No. 2129, 5/13/2019; and by Ord. No. 2184, 7/11/2022]
(a)
The State College Area School District (SCASD) may not permit non-SCASD
organizations to use the South Track Field when lighted.
(b)
For all events except band practice, the lights may be operated until
9:00 p.m. but shall be turned off within 15 minutes after the conclusion
of any event.
(c)
Band practice may be conducted with the use of the lights two nights
a week with practice concluded by 8:30 p.m.
(5)
Maximum Illuminance Levels at Property Lines. The maximum illumination
levels permitted at the property line(s) during nighttime produced
by the sum of all outdoor lighting installations on said property
shall be measured at grade in Horizontal Footcandles and shall be
in accordance with the requirements in Table I for the zoning district
in which the property is located, except for Memorial Field, located
in the RO-A zoning district, which shall be permitted at a maximum
average-maintained luminance of 2.5 footcandles measured at a distance
of 50 feet beyond the property line. [Table 1 is at the end of this
chapter Part.]
(6)
Luminaire Height. In nonresidential zones, the maximum height of
luminaires for outdoor facility lighting and event lighting shall
not exceed 70 feet. In residential zones, the maximum height of luminaires
shall not exceed the requirements in Table 1. Exceptions: The maximum
height of luminaries for outdoor facility and event lighting at Memorial
Field, located in the R-OA Zoning District, and the South Track facility
at the State College Area High School, South Campus, located in the
R-3B Zoning District, shall not exceed 70 feet.
[Amended by Ord. No. 2129, 5/13/2019]
(7)
Zoning Permit and Lighting Plan Required. An approved zoning permit and lighting plan are required prior to the installation of any outdoor facility or event lighting application as described in this chapter Part including all one- and two-family applications. All lighting plans shall be prepared and submitted to the municipality in accordance with the provisions of Section 2709. The zoning permit shall not be issued until the lighting plan is approved by the municipality.
e.
Security Lighting Requirements.
(1)
Applicability. The requirements specified in this chapter Part apply
to all outdoor security lighting installations except for those installations
at one- and two-family dwellings.
(2)
Use of Non-cutoff Luminaires. Security lighting presents unique lighting
situations that often require the use of non-cutoff luminaires. Non-cutoff
luminaires shall be permitted provided that the luminaires used meet
the following requirements:
(a)
All luminaires shall be shielded and aimed so that the candlepower
distribution is directed toward the functional area being secured
or protected. Luminaires shall not be directed toward property lines
if such direction causes light trespass.
(b)
Security lighting shall not be used to illuminate vertical surfaces
(e.g., building facades, walls, doors, and windows) that are higher
than eight feet above grade.
(c)
Security lighting shall not be mounted on poles that are located
farther than 10 feet from the perimeter of the designated secured
area.
(d)
Security lighting used to illuminate a perimeter such as a fence
line shall have motion sensors that will keep lights off until activated
by motion.
f.
Building Facade and Landscape Lighting Requirements.
(1)
Applicability. The requirements specified in this chapter Part applies
to all outdoor lighting installations employed for nighttime illumination
of building facades, structures, and exterior landscaping except for
those installations at one- and two-family dwellings.
(2)
Nonresidential Zones. In nonresidential zoning districts the exterior
surfaces of all buildings and structures may be illuminated as follows:
(a)
The luminaire height shall not exceed the requirements in Table
1 for the zoning district in which the installation is located. [Table
1 is at the end of this chapter Part.]
(b)
Cutoff luminaires may be mounted on walls or under roof overhangs
to illuminate facades. The maximum initial illuminance level produced
by any cutoff luminaire shall not exceed 4,000 lumens.
(c)
Spotlights or floodlights may be used to illuminate building
facades provided they are shielded and aimed so that the candlepower
distribution is directed toward the functional area being illuminated
on the facade. They shall not be directed toward property lines when
such direction causes light trespass. And, the maximum initial illuminance
level produced by any spotlight or floodlight shall not exceed 4,000
lumens.
(d)
Non-cutoff luminaires using globes or architectural-styled fixtures
may be installed on walls or otherwise situated to illuminate first
level facades provided that the maximum initial illuminance level
produced by such non-cutoff luminaire shall not exceed 2,300 lumens
and the mounting height does not exceed 10 feet above grade.
(e)
Neon lighting used to decorate or highlight a building shall be permitted to the following extent: (1) the cumulative length of neon light tubing that shall be permitted on the exterior of the building shall be limited to the amount determined by multiplying the lineal length of all sides of the building facing a street or alley by 2 and in no case shall the cumulative length of such neon lighting exceed 200 lineal feet of light tubing per building. Irregular building sides with indentations, etc., shall be measured by lineal footage as the side faces the street or alley. Front shall mean any side facing a street or alley. All fronts shall be summed together. (2) neon lighting shall not be located higher than 25 feet above grade. (3) the maximum diameter of neon tubing shall not exceed one inch. (4) neon used in signs shall be regulated pursuant to Chapter XV of this Codification.
(3)
Residential Zones. In all residential zoning districts, the exterior
surfaces of all building and structures are prohibited from being
illuminated except for buildings or structures with symbolic or historical
significance like churches, schools, or public buildings. Illumination
of these exempted structures shall be in accordance with the requirements
in Section 2706.f(2) of this chapter, as stated above.
(4)
Landscape Lighting. In all zoning districts non-cutoff luminaires
such as floodlights are permitted to be used to illuminate landscaping.
All non-cutoff luminaires shall be shielded and aimed so that the
candlepower distribution is directed toward the functional landscape
area being illuminated. Luminaires shall not be directed toward property
lines if such direction causes light trespass. The maximum initial
illuminance level produced by any luminaire shall not exceed 4,000
lumens.
g.
Outdoor Sign Lighting Requirements.
(1)
Applicability. The requirements specified in this chapter Part apply to outdoor lighting installations employed for nighttime illumination of signs. Chapter XV of this Codification provides restrictions on the location and types of signs that are permitted to be illuminated.
(2)
Non-Cutoff Luminaire Requirements. When illumination is permitted
pursuant to the Sign Ordinance and non-cutoff luminaires such as floodlights
are used, all non-cutoff luminaires shall be shielded and aimed so
that the candlepower distribution is directed toward the sign being
illuminated. Luminaires shall not be directed toward property lines
if such direction causes light trespass. The maximum initial illuminance
level produced by any luminaire shall not exceed 4,000 lumens.
(3)
Backlit Awnings, Canopies, and Marquees. The maximum illuminance
level permitted on the outside surface of a backlit awning, canopy,
or marquee shall not exceed 10 footcandles, as measured with a light
meter one inch or less off of the outside surface of the awning, canopy,
or marquee. Transparent materials are not permitted.
Backlit awnings, canopies, and marquees and the internal illumination
of signs are not permitted in the UV zoning district.
h.
Residential Outdoor Lighting Requirements.
(1)
Applicability. The requirements specified in this chapter Part applies
to outdoor lighting installations at one- and two-family dwellings.
(Note: Also, see Section 2706.d of this chapter for specific requirements
pertaining to illumination of tennis courts or other recreational
facilities at one- and two-family homes.)
(2)
Floodlight and Spotlight Requirements. All floodlights and spotlights
used for any purpose whatsoever shall be aimed and equipped with glare
shields, visors, barn doors, or shielding to prevent glare and light
trespass across property lines.
(3)
Other Non-Cutoff Luminaires. Unshielded luminaires other than floodlights
and spotlights such as lamppost lights, porch lights, garage lights,
driveway lights, etc. are permitted provided that the maximum initial
illuminance level shall not exceed 1,750 lumens. All installations
that exceed 1,750 lumens (approximate brightness of a one-hundred-watt
incandescent light bulb) shall be equipped with glare shields, visors,
barn doors, or other shielding to prevent glare and light trespass
across property lines.
|
(e)
|
Exception for Period Style Luminaires in Parks. Non-cutoff luminaire
installations are permitted in park applications provided all of the
following are met: (1) Style of lighting fixtures and posts shall
be vintage or architectural or historic; (2) the maximum initial illuminance
level of any non-cutoff luminaire shall not exceed 9,500 lumens; and
(3) no luminaire shall be mounted higher than 15 feet above grade.
|
[Ord. 1631, 8/14/2000, Section VII]
The light meter used for verification of illuminance levels
shall be certified by the manufacturer as meeting N.I.S.T. (National
Institute of Standards and Technology) standards for light meters.
The accuracy of the light meter shall be certified yearly by an approved
facility for testing light meters.
[Ord. 1631, 8/14/2000, Section VIII]
The provisions of this ordinance, to be known as the Lighting
Ordinance, shall be administered and enforced as part of the Zoning
Ordinance.
[Ord. 1631, 8/14/2000, Section IX.a., IX.b., IX.c.]
Whenever a Lighting Plan is required pursuant to Section 2706 of this chapter, the plan shall provide a site plan and other information as listed in this chapter Part. The site plan for a lighting installation may be included as a part of the site plan submitted for land development when a lighting installation is proposed incidental to land development. The following drawings and information shall be provided as part of the lighting plan:
a.
Site Plan. Drawn to scale with the following information identified
on the plan:
(1)
Zoning district and use of the property.
(2)
Property boundary lines.
(3)
Zoning districts and uses of adjoining properties.
(4)
Public roadways and rights-of-way on or adjoining the property.
(5)
Principal buildings and structures on the property.
(6)
Areas or elements to be illuminated on the property.
(7)
Proposed layout of the outdoor lighting installation on the property
including, but not limited to, all pole-mounted luminaires, bollard
or pedestal-mounted luminaires, canopy-mounted luminaires, and luminaires
mounted on the exterior of buildings and structures. Each luminaire
must be identified by a type designation.
(8)
Results of the lighting design superimposed on the site plan. This
may be in the form of isofootcandle diagrams or isoflux diagrams,
drawn to scale with the value contours labeled; or indicated with
a point-by-point value. In either case, the information presented
shall be of sufficient quantity and detail to determine compliance
with the requirements of this ordinance.
(9)
The lighting design information required in "b" below.
b.
Required Lighting Design Information.
(1)
The total light loss factor(s) used in the calculations to determine
maintained illuminance values.
(2)
The maximum maintained illuminance value at grade within the functional
area being illuminated (in horizontal footcandles or horizontal lux).
(3)
The average maintained illuminance value at grade of the functional
area being illuminated (in horizontal footcandles or horizontal lux).
(4)
The maximum maintained illuminance values at grade along all property
lines (in horizontal footcandles or horizontal lux).
c.
Required Luminaire Information.
(1)
A luminaire (light fixture) schedule of all luminaires used for the
outdoor lighting installation. Each luminaire type shall be indicated
by a type designation that correlates with those indicated on the
site plan. The luminaire schedule may be indicated on the site plan
or submitted separately. The luminaire schedule shall include the
following information for each luminaire type: description of luminaire,
mounting configuration and height, IES candlepower distribution classification
(cutoff, semi-cutoff, or non-cutoff), IES lateral light distribution
if applicable (Type I, Type II, Type III, Type IV, or Type V), lamp
type, lamp wattage, and lamp initial lumens.
(2)
Manufacturer's product data sheets (catalog cuts) for each luminaire
type.
(3)
Manufacturer's photometric report (certified to IES standards) for
each luminaire type. The photometric report shall clearly indicate
the cutoff classification of the luminaire.
[Ord. 1631, 8/14/2000, Section X; amended by Ord. 1823, 11/9/2005,
Sections II and III]
The lighting design information and luminaire information submitted
for approval shall correlate with the actual lighting equipment installed
in the field. Installation of lighting equipment in the field that
is not the same as the approved equipment in the design submittal
is prohibited, unless otherwise approved by the Zoning Official. If
for any reason the approved design does not produce actual field illuminance
levels that are within the ranges permitted by this ordinance, the
applicant or property owner, as the case may be, shall be required
to modify the lighting installation so as to comply with permitted
illuminance levels. Failure to modify shall constitute a zoning violation.
In addition, upon oral or written request of the Zoning Officer,
the property owner or his agent shall be required to show the zoning
official lamps installed in luminaires by removing same if necessary
for the purpose of ascertaining compliance with lumen levels as provided
for in this ordinance. Failure to show and remove lamps within a reasonable
time upon request shall constitute a zoning violation.
[Ord. 1631, 8/14/2000, Section XI]
For purposes of enforcement, initial illuminance levels produced
by outdoor lighting installations shall be the maintained illuminance
levels allowed by the ordinance for specific applications divided
by the light loss factor (LLF). As measured in the field, a 10% deviation
from the illuminance levels allowed by the ordinance is permissible.
[Ord. 1631, 8/14/2000, Section XII]
The SI unit of luminous intensity. One candela is one lumen
per steradian (lm/sr).
Luminous intensity expressed in candelas.
The vertical angle measured above nadir at which the light
source from a luminaire is no longer visible.
A luminaire light distribution is designed as cutoff when
the candlepower per 1,000 lamp lumens does not numerically exceed
25 (2.5%) at an angle of 90° above nadir (horizontal) and 100
(10%) at a vertical angle of 80° above nadir.
The assembly that holds the lamp along with any globe, shade,
or other covering surrounding the lamp.
Any lamp or luminaire that by its design concentrates light
output into a directional beam.
A unit of illuminance. One footcandle is one lumen per square
foot (lm/ft2).
A subjective term used to describe any illumination from
a light source that strikes the viewer's eye causing annoyance, discomfort,
or loss in visual performance or visibility.
It is measured as the vertical distance between the top of
the luminaire and the ground directly below the luminaire.
The areal density of the luminous flux incident at a point
on a surface. It is measured in footcandles.
A non-technical term designating the state of emitting visible
light or having visible light reflected off an object.
The component of a luminaire that produces the actual light.
Radiant energy that is capable of exciting the retina and
producing a visual sensation.
The ratio of illuminance for a given area to the value that
would occur if lamps operated at their initial rated lumen output
and if no system variation or depreciation had occurred.
A subjective perception of undesirable illumination including
the following examples:
|
•
|
The classic light shining in a window
|
|
•
|
Unwanted light on an adjacent property
|
|
•
|
Excessive brightness (glare) in the normal field of vision
|
A functionally related group of interacting luminaires used
to illuminate a specific area.
SI unit of luminous flux. Photometrically, it is the luminous
flux emitted within a unit solid angle (one steradian) by a point
source having a uniform luminous intensity of one candela.
A complete lighting unit consisting of a light source(s)
together with all parts designed to control the light distribution,
and any other mechanical, electrical, or decorative parts.
The emitted or reflected light from a surface the amount
of which causes perceived brightness. The unit of luminance is the
candela per square meter (cd/m2).
Radiant flux (radiant power); the time rate of flow of radiant
energy evaluated in terms of a standardized visual response.
The luminous flux per unit sold angle in the direction in
question. Can be expressed in candelas or lumens per steradian (lm/sr).
The average of all points on the surface of the illuminated
area.
A device that switches lighting on and off in response to
the motion.
A tract of land reserved for public use as playgrounds, trails,
paths, natural areas, or recreational areas and other public areas.
Lighting designed for and expressly used to deter criminal
activity by illuminating a specific area at nighttime.
[Ord. 1631, 8/14/2000, Section XII; amended by Ord. 1823,
11/9/2005, Sections 2 and 3]
|
Table 1
Outdoor Area Lighting Standards
| ||
|---|---|---|
|
Zoning District
|
Maximum Maintained Illuminance at the Property Line
|
Maximum Permitted Height of Luminaire
|
|
R-1 and R-2
|
0.2 FC
|
15 feet
|
|
R-3, R-3A, R-3H, R-O, RO-A and R-4, UV
|
0.2 FC
|
20 feet
|
|
R-3B
|
0.2 FC
|
25 feet
|
|
PK and PA
|
0.5 FC
|
25 feet
|
|
CP-1, CP-2, MP, and P-O
|
0.5 FC (0.2 when adjoining residential uses)
|
25 feet (20 feet within 100 feet of residential district or
building)
|
|
C and UPD
|
0.5 FC (0.2 when adjoining residential uses)
|
25 feet (20 feet within 100 feet of residential district or
building)
|
|
Addendum
Typical Lumens per Watt by Lamp Type
| |
|---|---|
|
20 lumens
|
Incandescent
|
|
54 lumen
|
Mercury Vapor
|
|
80 lumens
|
Metal Halide (white light)
|
|
125 lumens
|
High-pressure Sodium (HPS)
|
|
183 lumens
|
Low-pressure Sodium (LPS)
|
|
Source: Light Pollution: Problems and Solutions, Astronomical
Society of the Pacific
|
