A. 
Applicability. Unless otherwise stated, parking and loading shall be provided as is outlined in this article.
B. 
General provisions.
(1) 
Accessible parking. Parking facilities accessible for persons with disabilities shall be in compliance with or better than the standards detailed in the state and federal building or accessibility requirements, including quantity, size, location, and accessibility.
(2) 
Maximum vehicle parking. This article establishes the maximum number of vehicular parking spaces that can be provided for each use; there is no minimum number of parking spaces, except as noted.
(3) 
Minimum bicycle parking. This article establishes minimum requirements for bicycle parking.
(4) 
Parking design. This article details the parking design and location for vehicle and bicycle parking spaces.
(5) 
Requirements for unlisted uses. Parking spaces will be provided as detailed in Table 7.2-1. If a use is not listed, the City Planner is authorized to apply standards for a use deemed as similar. In the instance where an equivalent may not be clearly determined, the City Planner may require a parking study, transportation management plan, or other evidence that will help determine the appropriate requirements.
A. 
Parking Table.
(1) 
Table 7.2-1 outlines the maximum off-street parking spaces per use unless otherwise noted.
Table 7.2-1
Parking Table
Use
Parking Spaces
Residential/Lodging
Hotel/motel
1 per 1 guest room plus 1 per employee on largest shift
Bed-and-breakfast
1 per guest room; 1 for innkeeper/home occupant
Dormitory
1 per 3 beds or per City-approved institutional campus master plan
Nursing home/assisted living/rehabilitation center/adult foster care
1 per employee on largest shift; 1 per facility vehicle; 1 per 5 beds
Residential
1 per dwelling unit; detached and attached units may permit 2 per dwelling unit
Residential: senior housing
0.75 per dwelling unit, plus 1 per employee on largest shift
Residential: off-campus student housing
2 per dwelling unit; minimum 1 per dwelling unit
Rooming house
1 per unit or bedroom
Transitional residence
1 per employee on largest shift
Civic/Institutional Uses
Assembly/theater
1 per 3 persons permitted at maximum occupancy
Assembly, religious
1 per 6 seats in worship area or 1 per 40 square feet without seats
College and university
Based on similar use or per City-approved institutional campus master plan
Hospital
1 per 3 beds or per City-approved institutional campus master plan
Library and museum
1 per 3 persons permitted at maximum occupancy
Police and fire station/utilities and public services
1 per employee on largest shift; 0.75 per fleet vehicle
School
2 per 3 employees at largest shift, plus 1 per 10 students enrolled in grades 10 to 12
Commercial
Agriculture
1 per employee on largest shift; 1 per 330 square feet of retail
Day care
1 per employee on largest shift, in addition commercial facilities: 1 per 4 children
Eating and drinking establishments
1 per 4 persons at maximum occupancy; 1 per 2 employees at largest shift
Entertainment sports
Participant
1 per 5 persons at maximum occupancy; 1 per 2 employees at largest shift
Spectator
1 per 6 fixed seats or 1 per 40 square feet without seats
Retail/services
1 per 330 square feet
Services: medical services/offices
1 per employee on largest shift; 1 per patient at maximum patient capacity
Kennels
1 per employee on largest shift; 1 per 3 animals permitted
Office
1 per 300 square feet
Outdoor sales and storage
1 per employee at largest shift; 1 per 2,500 square feet outdoor sales area
Self-storage/mini-storage
1 per employee on largest shift; 1 per 75 storage units
Vehicle service
1 per 200 square feet floor area; in addition, vehicle repair: 2 per repair bay or area
Vehicle service: car wash
1 per employee on largest shift
Industrial
Craftsman industrial
1 per employees on largest production shift; 1 per 500 square feet retail
Industrial
1 per 1 employee on largest shift (includes shift, office, and maintenance staff)
(2) 
Total required vehicular parking spaces should be determined using the following parameters in addition to Table 7.2-1.
(a) 
Fractions. In determining the number of spaces required, any fraction of spaces required under 1/2 shall be disregarded; a fraction equal to or greater than 1/2 shall be rounded up to count as one space.
(b) 
Maximum occupancy. Maximum occupancy of the usable areas is determined by the Building Official or their designee.
(c) 
Exceeding the maximum parking spaces provided. Off-street parking may exceed the amounts in Table 7.2-1 by up to 10% except as follows:
[1] 
Up to 25% over the amounts in Table 7.2-1 permitted by-right when the property is located on a City Connector street type or in the Community Commercial (CC) District.
[2] 
Consideration of relief in the maximum overage allowances will take the following into account in addition to the variance review criteria outlined by the state.
[a] 
Availability of on-street and shared parking opportunities within walking distance.
[b] 
Location in or adjacent to walkable, mixed use areas of Downtown and Node Districts.
[c] 
Impact on the ability of the property to meet the maximum impervious coverage requirements as detailed in Article 5.
[d] 
Existing funding from the state or other federal source tied to design standards with a minimum parking requirement.
[e] 
Presence of the Natural Features Protection (NFP) Overlay, as detailed Article 6, on the property in question.
B. 
Vehicular parking design and location. Vehicular parking facilities shall be provided using the following standards.
(1) 
Design. Vehicular parking shall be designed as follows:
(a) 
Space dimension. Parking space design shall follow the dimensions in Table 7.2-3, Parking Space and Aisle Dimensions, and Figure 7.2-1, Parking Space and Drive Aisle Dimensions.
Table 7.2-3
Parking Space and Aisle Dimensions
Angle of Parking
(degrees)
Stall Dimensions
Drive Aisle Width
Curb Length
(feet)
Stall Width
(feet)
Stall Depth
(feet)
One-Way
(feet)
Two-Way1
(feet)
0° (Parallel)
18
8
18
12
20
45°
12
8.5
18
12
20
60°
10
8.5
18
18
20
90°
8.5
8.5
18
20
20
NOTE:
1 One twenty-six-foot aisle width is permitted when designated as the site's fire lane through site plan review.
050 Fig 7.2-1 Parking Space Dimens.tif
Figure 7.2-1 Parking Space and Drive Aisle Dimensions
(b) 
Wheel stops. Wheel stops or bumper guards are required for spaces adjacent to property lines, landscape buffers, and pedestrian pathways, internal to site or in public right-of-way.
(c) 
Tandem spaces. Tandem spaces are permitted as follows:
[1] 
Two spaces may be placed in tandem, provided that one space is accessible by an aisle, driveway, or alley.
[2] 
Tandem spaces are permitted for use by residential units only and must be utilized by the occupants of the same dwelling unit.
(d) 
Slope. All parking areas, driveways, and sidewalk access to parking areas shall meet the requirements of the American Disabilities Act.
(e) 
Materials. Parking areas may be designed with impervious or semipervious materials, such as concrete, asphalt, macadam, brick, and stone.
[1] 
Gravel and crushed stone are permitted for parking lots for residential parking areas up to 10 spaces and for all parks and open space uses. Additional application of these types of material may be permitted with approval of the City Planner.
(f) 
Landscape areas.
[1] 
Areas not used for sidewalks, parking spaces, drive aisles, loading, or refuse shall be constructed and maintained as landscaped areas.
[2] 
The perimeter of a parking lot shall be treated with fencing and/or landscaping along all property lines following Article 8, Landscape and Screening.
(g) 
Lighting. Parking areas with 50 or more spaces must be lit per Article 10, Lighting.
(h) 
Pedestrian access. Parking lots with more than two double-loaded aisles will provide internal pedestrian access both through the lot and, if directly adjacent to right-of-way, from the adjacent right-of-way to the structure(s) entrance.
[1] 
Dimension. The pedestrian access pathway shall be at least six feet in width.
[2] 
Location. The pathway(s) shall be centrally located and lead directly to a building entrance.
[3] 
Buffer. The pathway shall be buffered from drive aisles with landscaping or designated parking stalls and delineated with paint where it crosses drive aisles.
(2) 
Vehicular parking location. If located in a district with lot type standards, refer to those standards for parking lot location. In addition, the following applies:
(a) 
Access. All spaces, unless otherwise noted, shall front on a drive aisle, driveway, or right-of-way providing direct access the parking space.
(b) 
Parking in yards. Motorcycles and vehicles must be parked on driveways, permitted parking areas, or within a structure.
(c) 
Recreational vehicles. Trailers, motor homes, recreational vehicles, boats, or other similar vehicles may be parked as follows:
[1] 
Recreational vehicles may be stored on a driveway in the front or corner yard between May 1 and October 15 and in the side and rear yards without restrictions.
[2] 
Recreational vehicles must be kept in good repair and carry a current license and registration.
[3] 
A maximum of two recreational vehicles can be stored out of doors on a lot at a time; there is no limit as it relates to vehicles within fully enclosed structures.
A. 
Required Bicycle Parking Table.
(1) 
Table 7.3-1 outlines the required minimum number of spaces for bicycle parking.
Table 7.3-1
Required Minimum Bicycle Parking Table
Use
Required Spaces
Residential/Lodging
Bed-and-breakfast/hotel/motel
1 per 7 employees
Dormitory
1 per 5 beds or per City-approved campus master plan
Nursing home/assisted living/rehabilitation center/adult foster care
1 per 7 employees
Residential
1 per 5 dwelling units
Civic/Institutional Uses
Assembly/theater
1 per 50 persons permitted at maximum occupancy
Assembly, religious
1 per 50 seats in worship area or 100 square feet without seats
College and university
Based on similar use or per City-approved campus master plan
Hospital
1 per 15 employees or per City-approved campus master plan
Library and museum
1 per 7 employees
Parks and open space
1 per 5,000 square feet of land area or per City parks and recreation plan
School
2 per classroom
Commercial and Industrial
Agriculture
1 per 5 employees or gardeners
Eating and drinking establishments and entertainment sports (participant)
1 per 15 persons permitted at maximum occupancy
Office/employment uses/other
1 per 7 employees
Parking, stand-alone surface lot or garage/ramp
1 per 15 parking spaces
Retail/services
1 per 7 employees
(2) 
Total required bicycle parking spaces should be determined using the following parameters in addition to Table 7.3-1.
(a) 
Calculation. At least one space is required. Beyond the first space, in determining the number of spaces required, any fraction of spaces required under 1/2 shall be disregarded; a fraction greater than 1/2 shall be rounded up to count as one space.
(b) 
Public bicycle parking spaces. Parking facilities within public spaces, such as street rights-of-way, can count toward the requirement for nonresidential uses. All facilities located within a public right-of-way require review and approval of an encroachment agreement with the City.
B. 
Bicycle parking design and location. Bicycle parking facilities shall be provided using the following standards:
(1) 
Design. Bicycle parking shall be designed as follows:
(a) 
Space size. Each bicycle parking space must be at least six feet long and two feet wide with a five-foot access aisle.
(b) 
Improved surface. Bicycle parking must be located on an improved surface such as asphalt.
(c) 
Bicycle racks. Bicycle racks must be designed as follows:
[1] 
Be a fixed-in-place stand that is securely anchored to the ground and/or wall.
[2] 
Provide at least two points of contact to allow locking of frame and at least one wheel.
[3] 
Be constructed of materials that resist cutting, rusting, bending, or deformation.
(d) 
Lockers. Lockers must be designed as follows.
[1] 
Be a fixed-in-place stand that is securely anchored to the ground and/or wall.
[2] 
Be secured by means of a lockable door or configured internally to allow locking of the frame and at least one wheel.
(2) 
Location. Bicycle parking shall be located as follows.
(a) 
Visible location. If not visible from the street or public entrance, a directional sign must be posted indicating location. Adherence to the Manual On Uniform Traffic Control Devices for signage is recommended.
(b) 
Structured parking. If more than 50% of a site's vehicular parking is in a covered area or structure, the required spaces shall also be located in the covered area or structure or otherwise protected from the weather.
A. 
Off-street loading. Construction of new buildings that are expected to have deliveries by vehicles rated as heavy-duty must provide off-street loading facilities as follows:
(1) 
Design. Each loading space shall be a minimum of 10 feet in width, 25 feet in length, and 14 feet in height.
(2) 
Location. Loading areas shall be located as follows:
(a) 
All off-street loading areas. Regardless of truck type, loading areas shall not be located in the front build-to zone and may not occupy any part of a required front or corner yard.
(b) 
Loading areas shall not be located closer than 50 feet from a residentially zoned lot unless it is wholly enclosed within the building or by walls.
(c) 
Loading areas must be separate from pedestrian facilities and pathways.
A. 
Driveways. Driveways will be designed as follows:
(1) 
Driveway width. Driveway width is measured at the front property line and shall adhere to the following:
(a) 
Single-lane driveways. Single-lane driveways shall be between eight feet and 12 feet.
(b) 
Double-lane driveway. Double-lane driveways shall be between 20 feet and 24 feet, unless the driveway serves the off-street loading area where a larger driveway may be required based on site plan review.
(2) 
Double-track driveways. Double-track, wheel strip, or ribbon driveways are permitted as follows:
(a) 
The first two feet of the entire driveway width, measured from the property line, must paved or covered with a permitted material.
(b) 
The wheel strip shall be at least 18 inches in width.
(c) 
The area between the wheel strips must be landscaped with living ground cover.
(3) 
Materials. Driveways may be designed with impervious or semipervious materials, such as concrete, asphalt, macadam, brick, and stone.
(a) 
Gravel and crushed stone are permitted for residential driveways accessing parking areas up to 10 spaces. Additional application of these types of material may be permitted with approval of the City Planner.
(4) 
Maximum coverage of front yard. Driveways cannot account for more than 30% of the front yard of a lot.