SECTION 7.1.1 EXTERIOR CONSTRUCTION STANDARDS,
GENERALLY
The following design standards shall apply
generally and by use type within the zoning district in which the
development is proposed.
A.
Masonry Construction.
This term shall be construed
to mean that form of construction composed of brick, stone, decorative
concrete block or tile, or other similar building units or materials
(or combination of these materials) laid up unit by unit and set in
mortar, unless otherwise permitted under this section, and shall exclude
wall area devoted to doors and windows. As applicable to meeting minimum
requirements for the exterior construction of buildings within each
zoning district, this term shall include the following materials:
1.
Hard Fired Brick.
Kiln fired clay or slate material.
Brick may include concrete brick if it is to the same ASTM standard
for construction as typical hard fired clay brick. Brick shall be
severe weather grades; minimum thickness of three (3") inches when
applied as a veneer; and shall not include unfired or under-fired
clay, sand, or shale brick.
2.
Stone.
Stone shall include naturally occurring
granite, marble, limestone, slate, river rock, and other similar hard
and durable all-weather stone that is customarily used in exterior
building construction. Stone may also include cast-or manufactured-stone
product, provided that such product yields a highly textured, stone-like
appearance; its coloration is integral to the masonry materials and
shall not be painted or sprayed on; and it is demonstrated to be highly
durable and maintenance-free. Natural or manmade stone shall have
a minimum thickness that meets industry standards.
3.
Decorative Concrete Block.
Decorative Concrete
Block shall include highly textured finish, such as split-face, indented,
hammered, fluted, ribbed or similar architectural finish. Coloration
shall be integral to the masonry material and shall not be painted
or sprayed on. Decorative Concrete Block shall have a minimum thickness
that meets industry standards when applied as a veneer and shall not
include lightweight or featherweight concrete block or cinderblock
units. Decorative Concrete Block shall not be used as a material in
single-family, duplex, multifamily, or single-family attached structures.
4.
Concrete Pre-Cast or Tilt-Wall Panels.
This material
shall only be allowed if a highly textured architectural finish which
appears texturally as face brick or stone. Concrete pre-cast or tilt-wall
panels may be brick-like or stone-like in appearance. Coloration of
the material shall be integral to the masonry material and shall not
be painted on or sprayed on. This material shall not include smooth,
untextured or inadequately textured finishes. Concrete pre-cast or
tilt-wall panels shall not be used as a material in single-family,
duplex, multifamily, or single-family attached structures.
5.
Glass Blocks or Tiles.
This material shall be
of the type customarily used in exterior building construction. It
shall not comprise more than thirty (30%) percent of any exterior
wall surface, nor more than twenty (20%) of the building’s total
exterior on all wall surfaces combined. It shall not be highly reflective
or contain a mirror-like finish.
6.
Stucco.
Stucco or plaster shall only be allowed
as a masonry material when applied using a 3-step process over diamond
metal lath mesh to a 7/8th inch thickness or by other processes producing
comparable stucco finish with equal or greater strength and durability
specifications.
B.
Prohibited Materials and colors.
Unless specifically
approved by the City Council on an approved site plan for single-family,
single-family attached, attached multifamily, institutional, office,
retail, commercial, industrial, or other nonresidential structures,
the following materials shall not qualify or be defined as “masonry
construction” in meeting the minimum requirements for the exterior
construction of buildings:
1.
Exterior plaster, adobe or mortar wash, surface materials unless
otherwise permitted in this section;
2.
Exterior insulation and finish systems (EIFS), acrylic matrix,
synthetic plaster, or other similar synthetic material;
3.
Cementitious fiber board siding (such as “Hardy Plank,
Hardy Board, etc.), unless otherwise provided herein;
4.
PVC or other plastic-based siding materials;
5.
Lightweight or featherweight concrete blocks, cinderblocks or
other lightweight based masonry unit;
6.
Any other cementitious product not listed above.
7.
Any pastel or bright colors painted directly to the surface
of the exterior structure. All structures shall have an exterior color
of muted earth tones such as, but not limited to, reds, browns, tans,
grays, and greens.
SECTION 7.1.2 MINIMUM DESIGN STANDARDS
The standards and criteria contained within this subsection
are deemed to be the minimum standards and shall apply to all new
building construction or redevelopment occurring within the City unless
otherwise stated in this Ordinance.
A.
Single-Family and Two-Family Residential Zoning Districts
1.
The design standards for all single-family and duplex residential
structures within the SF-10, SF-6, SF-5 and D (Duplex) District shall
be as follows:
2.
All single-family and two-family (duplex) structures shall be
of exterior fire-resistant construction, and shall have a minimum
of eighty (80%) percent masonry construction, more or less equally
distributed around all sides of the structure, for the first story
of the structure, and a minimum of fifty (50%) percent masonry construction,
more or less equally distributed around all sides, for any additional
story above the first floor.
3.
Areas of a single-family or duplex structure’s facade
that are devoted to windows, doors, covered porches or patios that
have a minimum size of four feet (4') deep and eight (8') feet wide
(thirty-two (32) square feet), chimneys, breezeways, or courtyards
shall not be counted as “wall surface” when calculating
the masonry requirement.
4.
Prohibited materials.
Concrete, concrete block,
vinyl, plastic, or metal exterior construction is not permitted on
any single-family or duplex residential structure.
5.
Roof materials
for a single-family or two-family
(duplex) structure shall be comprised of an architectural, laminated,
dimensional composition shingle (thirty (30) year minimum); Metal
roofing with enamel baked finish or architectural grade metal roofing
products which are stamped to appear as wood shakes, dimensional shingles,
wood shingles, slate or tile; or terra-cotta or slate tile. All unfinished
metal roofing is prohibited. Acceptable colors are: Earth tones are
defined as a color scheme that draws from a color palette of browns,
tans, warm grays, and greens. The colors in an earth tone scheme are
muted and flat in an emulation of the natural colors found in dirt,
moss, trees and rocks, and the color pallet [palette] found in the
manufacture’s metal roofing with enamel baked finish. If roof
is not visible to the public, there is no pitch requirement (i.e.
parapet roof); if roof is visible to the public a minimum 6:12 pitch
is required.
6.
Chimney Stacks.
All chimney stacks for single-family
or duplex structures shall be of one hundred (100%) percent masonry
construction or may be constructed of cementitious fiber board.
7.
Elevation articulation.
The elevation of a single-family
or duplex structure, including garages facing the street shall contain
at least one section of at least twenty (20%) percent of the total
street elevation that is offset at least two (2') feet from the remainder
of the street elevation.
8.
Nonresidential buildings.
Any nonresidential building
constructed within any residential zoning districts shall conform
to the design standards of Section 7.1.4 below.
9.
Newly Constructed Single-Family Dwelling Required Architectural
Features.
All newly constructed single-family dwellings
are required to comply with the following architectural features:
a) Garage spaces for a minimum of two (2) vehicles
shall be attached to the primary structure and shall be located behind
the required building setback lines;
b) Wood or stained fiberglass or metal simulated wood
grain front door;
c) No Facade may be repeated within any adjacent lots
or across the street from those lots within groupings of five (5)
homes;
d) Concealed HVAC units, trash storage and utility
meters;
e) If brick is used, brick shall be properly detailed.
Brick shall be coursed exactly to the top and bottom of all wall openings;
f) Windows shall be single hung, double hung, triple
hung, or casement;
g) Flush mounted windows are prohibited;
h) Windows are to be placed on each wall elevation
with a wall-to-window ratio that meets the light and air requirements
of the building code;
i) If shutters are used, shutters shall be one-half
the width of, and the same height of the associated opening. All shutters
shall be louvered, paneled, or constructed of boards as appropriate
to the style of the building. Shutters do not need to be operable;
j) Gutters shall be copper, galvanized steel, aluminum
or painted if exposed;
k) Dormers shall not use siding as window jamb material;
l) The body of a single-window dormer shall be vertically
proportioned or square;
m) If chimneys are visible, they shall have a projecting
cap;
n) If chimneys are located on a street facing wall,
they shall extend to the ground;
o) If a porch is used, the porch column base shall
not protrude beyond the bottom edge of the porch flooring.
B.
Additional Newly Constructed Single-Family Dwelling Architectural
Features.
All newly constructed single-family dwellings
shall contain at least four (4) of the following architectural features:
1.
Stoop and portico at the front door
3.
Front porch or front stoop steps and railing
5.
Decorative or architectural porch railing
7.
If brick or stucco is used, a stone base below first floor window
shall be installed
9.
Decorative roof finials or ornamentation
10.
Decorative attic or gable feature greater than 3 SF in size
11.
Trim at windows and doors of the street facade
12.
Arched window head or heads (depending on architectural style)
on street facade
14.
Window shutters on street facade
16.
Decorative concrete driveway
SECTION 7.1.3 MULTIFAMILY RESIDENTIAL ZONING
DISTRICT STANDARDS
A.
The design standards for all multifamily and single-family attached
structures within the Multifamily (MF) zoning district shall be as
follows:
B.
All multifamily and single-family attached residential structures
shall be of exterior fire-resistant construction and shall have a
minimum of eighty (80%) percent masonry construction, more or less
equally distributed around all sides of the structure, for the first
story of the structure, and a minimum of fifty (50%) percent masonry
construction, more or less equally distributed around all sides, for
any additional story above the first floor.
C.
Areas of a multifamily and single-family attached residential
structure’s facade that are devoted to windows, doors, covered
porches or patios that have a minimum size of (4') feet deep and eight
(8') feet wide (thirty [thirty-two] (32) square feet), chimneys, breezeways,
or courtyards shall not be counted as “wall surface” when
calculating the masonry requirement.
D.
Prohibited materials.
Concrete, concrete block,
vinyl, plastic or metal exterior construction is not permitted on
any multifamily or single-family attached structure.
E.
Roof materials.
Roof materials for a multifamily
and single-family attached residential structures shall be comprised
of an architectural, laminated, dimensional composition shingle (thirty
(30) year minimum); flat pan standing seam metal roofing, or architectural
grade metal roofing products which are stamped to appear as wood shakes,
dimensional shingles, wood shingles, slate or tile; or terra-cotta
or slate tile. Sheetmetal or corrugated metal roofing materials is
prohibited. Roofs shall be earth tones. Earth tones are defined as
a color scheme that draws from a color palette of browns, tans, warm
grays, and greens. The colors in an earth tone scheme are muted and
flat in an emulation of the natural colors found in dirt, moss, trees
and rocks. If roof is not visible to the public, there is no pitch
requirement (i.e. parapet roof); if roof is visible to the public
a minimum 6:12 pitch is required.
F.
Accessory structures.
Accessory structures, regardless
of size, within the multifamily (MF) zoning district shall conform
to the minimum exterior construction standards for the main building
on the lot, tract, [or] site, and shall be architecturally compatible
with the main building.
G.
Separation of Multifamily Buildings:
1.
Buildings two stories or less in height with opposite walls
that:
a) Contain openings for windows, light and air ventilation
shall be separated by fifteen (15) feet between building walls;
b) Contain no openings shall be separated by ten (10)
feet between buildings walls.
2.
Buildings more than two stories in height with opposite walls
that:
a) Contain openings for windows, light and air ventilation
shall be separated by (20) feet between building walls;
b) Contain no openings shall be separated by fifteen
(15) feet between building walls.
SECTION 7.1.4 NONRESIDENTIAL ZONING DISTRICT
STANDARDS
The design standards for all nonresidential
and institutional structures within the Office Neighborhood Service
(O), Commercial (C), and Industrial (I) zoning districts, and for
nonresidential structures located within all other districts shall
be as follows:
A.
All nonresidential and institutional structures in any zoning
district, shall have a minimum of seventy-five (75%) percent masonry
construction, more or less equally distributed around all sides of
the building, for the first story defined as below the first floor
ceiling plate, and a minimum of fifty (50%) for any story above. Any
facade that faces, or is visible from a public street, shall have
a minimum of seventy-five (75%) percent masonry construction, and
all other facades shall be comprised of not less than fifty (50%)
percent masonry construction.
B.
Areas of a nonresidential or institutional structure’s
facade that are devoted to windows, doors, covered porches or stoops,
breezeways or courtyards shall not be counted as “wall surface”
when calculating the masonry requirement.
C.
Metal exterior material use.
Metal exterior construction
is prohibited on any nonresidential or institutional structure which
is located within any zoning district, save and except the following:
1.
Structures located on a through lot that both fronts and backs
onto a public street. The rear facade, which must be located equal
to or more than one thousand (1,000') feet from the public street,
may use metal exterior construction upon approval of the Site Plan
by the City Council, and;
2.
Upon approval of the Site Plan by the City Council, nonresidential
and institutional structures within any of the nonresidential zoning
districts may use metal as an exterior material on up to twenty (20%)
percent of the facade as an architectural accent.
a) The use of any type of metal for exterior building
construction shall be clearly shown on the Site Plan and shall only
be allowed with the Site Plan approval. The exterior finish of metal
used in exterior construction shall be permanent, maintenance-free
nature such as a baked-on finish unless approved otherwise on the
Site Plan. The use of corrugated, galvanized, aluminum-coated, zinc-coated
unfinished, or similar metal surfaces shall be prohibited unless approved
otherwise on the Site Plan.
D.
Roof materials.
Any roof materials for a nonresidential
or institutional structure that are visible from a public street shall
be shall be comprised of an architectural, laminated, dimensional
composition shingle (thirty (30) year minimum); flat pan standing
seam metal roofing, or architectural grade metal roofing products
which are stamped to appear as wood shakes, dimensional shingles,
wood shingles, slate or tile; or terra-cotta or slate tile. Sheetmetal
or corrugated metal roofing materials is prohibited. Roofs shall be
earth tones. Earth tones are defined as a color scheme that draws
from a color palette of browns, tans, warm grays, and greens. The
colors in an earth tone scheme are muted and flat in an emulation
of the natural colors found in dirt, moss, trees and rocks. If roof
is not visible to the public, there is no pitch requirement (i.e.
parapet roof); if roof is visible to the public a minimum 6:12 pitch
is required. Nonresidential or institutional structures with a flat
roof shall have highly articulated parapet that conceals the roof
and any roof-mounted mechanical equipment.
E.
Structural exceptions to masonry standards.
The
following structures are exempt from the masonry construction requirements.
1.
Barns located on the lots of four (4) acres or more provided
that such barns are used solely for agricultural purposes (as distinguished
from commercial purposes).
2.
Mobile homes and HUD-Code manufactured homes lawfully existing
are not subject to the masonry requirements.
3.
Temporary construction buildings, field offices, sales offices
and temporary classrooms or storage buildings for the public school.
The exception shall be only provided that such facilities are legally
permitted by the City for a specific period of time, and provided
that they are completely removed from the premises upon expiration
of the permit or upon completion of construction, whichever occurs
first.
4.
Residential and nonresidential structures legally in existence
as of (date of this ordinance), and any additions to such structures
that do not cumulatively exceed twenty (20%) percent of the original
building size (as it existed on date of this ordinance). Such additions
shall be allowed to be constructed of the same exterior materials
as the original building.
F.
Use of Alternative Exterior Materials.
1.
All written requests for the use of alternative exterior building
materials to include alternative roof material and/or roofing color
and alternative roof pitch shall be clearly noted and described in
detail on a color rendering of the structure’s elevation that
is submitted along with the site plan for approval. The use of alternative
exterior building materials, roof pitch and roof materials and/or
color may only be requested for multifamily, single-family attached
and nonresidential structures. The City may require submissions of
an actual sample(s) of the proposed exterior finish material(s) along
with the elevation(s) and the site plan.
2.
The City Council may approve, all alternative exterior construction
material(s), roof pitch and roof materials and/or color if it is determined
to be equivalent or better than the exterior materials, roof pitch,
or roof materials and/or colors otherwise required by this Subsection
and the City’s Building Code as part of the site plan approval
process.
G.
Consideration for exceptions to the above exterior construction
requirements shall be based only upon the following:
1.
Architectural design, creativity and innovation;
2.
Compatibility with surrounding structures;
3.
Relative ease of maintenance of the material(s);
4.
Long-term durability and weather-resistance of the materials(s);
and
5.
Long-term stability in property value due to the high quality
of the material(s).
(Ordinance 480-14 adopted 11/20/14; Ordinance 521-17 adopted 4/20/17; Ordinance
552-19 adopted 4/18/19)
SECTION 7.2.1 SCREENING WALLS AND FENCES
A.
General Requirements
1.
A permit shall be required for any new fence or screening wall
construction or replacement of an existing fence or screening wall
unless otherwise provided in this Ordinance. No permit shall be required
to repair a fence as long as the repair keeps the fence in the same
location and utilizes the same materials.
2.
All fences and screening walls shall be kept in good repair
and shall not create blight. Dilapidated fences or screening walls
shall be repaired or replaced in accordance with provisions of this
section. Wood fences shall be painted or stained with natural wood
colors on both sides.
3.
No fence or screening wall shall exceed eight (8) feet in height,
as measured from the grade of the property, unless otherwise approved
by the City Council during the site plan process or by way of a variance
in accordance with Section 3.2.6.
5.
Chain-link fencing not clad in vinyl may be allowed for fencing
of dog runs, tennis courts, swimming pools and similar purposes if
it is completely contained on the lot, not on the perimeter, and it
is not directly visible from any street or adjacent property.
6.
Temporary fencing used for construction purposes or special
events shall be exempt from the requirements of this section provided
that such fencing is approved as part of the applicable building permit
or special events permit.
7.
Any variances to the requirements of this section shall be considered
by the BOA unless otherwise provided in this Ordinance.
B.
Fencing Requirements for Agricultural Uses
1.
The following standards apply to tracts of land with four (4)
acres or more used for agricultural or animal husbandry purposes in
accordance with this Ordinance.
2.
Pipe fencing, split rail fencing, barbed wire, hog wire, chicken
wire, chain-link, cable, and other open style types of fencing traditionally
used in agriculture and animal husbandry shall be allowed. Such fencing
may be located up to the right-of-way line and shall not exceed eight
(8) feet in height. Solid style types of fencing shall meet the fence
height and setback requirements for residential uses. Open style fencing
typically used in wildlife management may exceed eight (8) feet in
height as necessary for the purposes of wildlife management.
3.
No permit is required for agricultural fencing.
C.
Electric Fences
1.
An electric fence is allowed on properties exceeding 20 acres
in all zoning districts, with proof submitted to the electrical inspector
that the fence will be designed to retain animals, be inaccessible
to the general public and not pose a hazard to life.
2.
An electric fence is allowed in association with a permitted
nonresidential outdoor storage area in the Industrial “I”
zoning districts subject to the following standards.
a) Unless otherwise specified in this Section, electric
fences must be installed in conformance with the specifications set
forth in the City’s electrical code and the International Electroctechnical
Commission Standard No. 60335-2-76. In addition, the electric fence
controller must meet the requirements of Underwriters Laboratories
Standard UL69, Electric-Fence Controller, and labeled as such.
b) The electric fence controller and emergency entry
key safe for the electric fence must be located in a single accessible
location for the entire fence.
c) The electric fence must be surrounded by a nonelectrical
fence or wall six to eight feet in height.
d) The electric fence must be installed a minimum of
one foot from the surrounding nonelectric fence or wall, except along
the gate. Along the gate, the electric fence must be installed a minimum
of three inches from the surrounding nonelectric fence or wall.
e) The electric fence must be clearly identified with
warning signs at intervals of not less than sixty (60) feet.
f) The electric fence must only be energized during
hours when the public does not have legal access to the protected
property.
D.
Prohibited Materials.
Permits shall not be issued
for materials not manufactured specifically for fencing, such as fibrous
masonry products, landscape timbers, railroad ties, latticework panels,
plywood, corrugated steel panels, metal sheets or fiberglass panels.
Other prohibited material include[s] razor wire fencing.
E.
Fencing Requirements for Residential Uses
1.
Fences shall be constructed of wood, ornamental metal (i.e.
wrought iron), tubular steel, masonry, or other materials traditionally
used in private fence construction. New and innovative materials such
as plastics, PVC’s, metal panel or slat, cementitious fiberboard,
and other similar materials may be approved for use by the City Council
if the material is compatible in character with traditional residential
fencing and proven to be sturdy, durable and relatively maintenance-free.
2.
The maximum height, as measured from the grade of the property,
shall be as follows:
a) Restrictions and requirements for a fence, wall
and barrier are as follows:
Fences in front yard – No fence,
wall or barrier may be built within the required front yard as established
by the zoning regulations of the City of Sansom Park except as follows:
(A) Required Setbacks on Residential Lots –
A fence may be erected in the front yard, as established by
the zoning regulations of the City of Sansom Park, of a residential
lot only if the following criteria are met:
i. The fence shall not exceed four (4) feet in height
above the adjacent grade;
ii. The fence shall be constructed to provide that
a minimum of 50% of the fence is open;
iii. On corner lots the fence shall not be located
within the designated visibility triangle; and
iv. The fence shall be constructed of wood, wrought
iron, plastic or similar fencing materials[.]
b) Maximum of eight (8) feet for side or rear yards.
3.
Fencing in the front yard of a residential lot shall be located
no closer than three (3) feet (measured inside the residential lot)
to the right-of-way line.
4.
Gates designed for vehicular access shall be set back from the
right-of-way line a minimum of twenty-four (24) feet.
5.
The height of a fence adjacent or perpendicular to a screening
wall shall not exceed the height of the subdivision’s screening
wall or any other fence constructed by the developer at the time of
initial development.
6.
All fences adjacent to parks, trails, or designated open spaces
shall be constructed of split rail, ornamental metal, tubular steel,
masonry columns, or similar open face material and not exceed a height
of six (6) feet. No wood fencing shall be allowed behind the required
open space. Solid fencing constructed of Cedar (with metal posts and
Cedar top and bottom caps and stained with wood sealant) or masonry
material may be allowed if adjacent to a park or open space area that
is used actively such as a public swimming pool, sport facility, etc.
7.
Allowable wood fences adjacent to streets, schools, parks, open
spaces or other public spaces shall have the finished side facing
the public space. All fence posts and structural components shall
be placed on the interior of the lot.
8.
All fence posts and structural components shall be placed on
the interior of the lot.
9.
The location of fences for double frontage lots or corner lots
adjacent to a street shall be in accordance with the building setback
line as shown on the final plat. If a property is not platted or if
no building line is shown on the recorded plat, the location of fences
shall comply with the building setback requirements of the zoning
district that the property is located in.
10.
If a corner lot is adjacent to a subdivision’s screening
wall, a fence may be placed outside the required setback line to connect
with the screening wall.
11.
Fences for nonresidential uses allowed in residential zoning
districts such as schools or Churches shall meet the fencing standards
for nonresidential districts.
F.
Fencing Requirements for Swimming Pools
1.
Swimming pools shall have a fence that shall conform to the
requirements of the International Building Code.
G.
Fencing and Screening Wall Requirements for Multifamily and
Nonresidential Uses
1.
Fencing shall not exceed six (6) feet in height.
2.
Fencing shall be constructed of wrought iron, tubular steel,
masonry, live screening, or a combination thereof unless adjacent
to single-family dwellings, or two-family dwellings, in which a screening
wall shall be constructed and shall be made of masonry materials with
masonry columns placed a minimum of thirty-two (32) foot on center.
Wood, barbed wire, and chain-link fencing is prohibited.
3.
All fencing and screening walls for multifamily and nonresidential
developments shall be identified on the site plan for the development
and approved as part of the site plan approval.
4.
The City Council may approve alternative fencing materials and
construction standards to any of these requirements as a part of the
site plan approval process when required.
5.
Screening walls shall be constructed of masonry material such
as brick, stone, concrete panels, or similar materials consistent
in material, finish, and color with the primary buildings within the
development or adjacent buildings in the area. The wall finish shall
be consistent on both sides.
6.
Screening walls shall be a minimum of six (6) feet in height
and a maximum of eight (8) feet in height on properties adjacent to
single-family and two-family residential districts. This screening
wall shall be constructed prior to issuance of a building permit for
any structure on the multifamily or nonresidential use property and
shall be maintained by the owner of the property used for multifamily
or nonresidential use.
7.
Screening wall plans shall be submitted to the City for review
and permitting and shall be signed and sealed by a Structural or Civil
Engineer licensed by the State of Texas.
8.
All uses which require storage such as, but not limited to,
auto impound lots, wrecking services, contractor yards, and other
facilities shall provide the storage of such items to be within completely
enclosed buildings or effectively screened with screening walls or
fences not less than six (6) feet in height nor more than eight (8)
feet in height, provided no storage located within fifty (50) feet
of such screening shall exceed the maximum height of such screening.
(Ordinance 480-14 adopted 11/20/14; Ordinance 494-15, sec. 5, adopted 5/21/15; Ordinance 500-16 adopted 1/21/15)
A. Applicability.
This Section shall apply to all new nonresidential and multifamily
development within the City of Sansom Park.
B. Purpose.
The purpose of this section is to encourage low maintenance
landscaping, water conservation and tree preservation while providing
guidelines for minimum landscaping for new development throughout
the City, preserving the natural, open character of the Rural Residential
areas, and not prohibiting the normal use of properties for agricultural
purposes.
C. Nonresidential
and Multifamily landscaping.
These standards apply to
new nonresidential and multifamily developments. These standards may
be met either by saving existing trees on the site, or planting new
trees from the recommended list.
1. A twenty
(20') foot linear landscape strip shall be provided adjacent to all
public streets. The landscape strip shall include a minimum of one
(1) shade tree (two and one-half inch caliper minimum) for every fifty
(50) linear feet of street frontage.
2. Where
parking lots and drives abut the landscape strip along a street right-of-way,
a continuous hedge of evergreen shrubs shall be provided to screen
those areas from the street. The shrubs must be a minimum of a ten-gallon
size at planting with a minimum mature height of three (3) feet. Shrubs
shall be planted according to the spacing recommended for their species.
The screening shall extend along the entire street frontage of the
parking lot, exclusive of driveways and visibility clips. A landscape
berm may be provided in lieu of the screening hedge. The berm must
be a minimum of thirty-six (36) inches above the average grade of
the street and parking lot curbs with a slope not to exceed 3:1.
3. Landscaping
shall also be provided for the interior parking areas. Trees shall
be planted in each parking lot to attain a minimum average density
of one (1) shade tree (two and one-half inch caliper minimum) for
each ten (10) parking spaces provided, or any fraction thereof. The
planting area per tree shall be a minimum of nine (9') feet wide and
twenty (20') feet deep.
a) Interior parking lot landscaping shall include a minimum eight (8%)
percent open space. To calculate the total parking area and the subsequent
percentage of required interior lot landscaping, total the square
footage of parking spaces, planting islands, curbed areas and all
interior driveways and aisles. Landscaped areas located contiguous
to and within five (5') feet of the parking lot may be used to meet
the interior landscaping requirement. Landscaped areas located greater
than five (5') feet away from the parking lot may not be used to meet
the interior landscaping requirement.
b) The required landscaping for parking lots shall be more or less evenly
distributed throughout the parking lot, although adjustments may be
approved by the City Manager or his/her designee where the shape or
size of the parking lot, the location of existing trees or other natural
constraints reasonably prevent such distribution.
c) Except for customer and employee parking, parking lot landscape requirements
do not apply to storage or standing parking spaces incidental to uses,
such as sales and rental of motor vehicles, mobile homes, boats, trailers
or other similar uses.
d) All landscaped areas, including the permeable areas and drip lines
around trees and planting beds used for visual screening which abut
any parking lot or vehicular travel area, shall be protected with
curbs sufficient to protect them from vehicular intrusion.
4. Foundation
Plantings.
Exposed sections of building walls that are
in high-use or high-visibility areas of the building exterior shall
have planting beds at least five (5) feet wide placed directly along
at least fifty (50) percent of such walls.
5. An
automatic irrigation system is required for all landscaping. Irrigation
systems shall be designed and installed with rain sensors and low
gallonage, low angle nozzles in such a way as to avoid water overflow
into the street. A freeze sensor shall be placed in each controller
to prevent the irrigation system from activating to create unsafe
spillage on roads and/or sidewalks.
D. Nonresidential
Area Treatment
1. Landscape
areas shall include all areas on the site that are not covered by
buildings, structures, paving or impervious surface. Landscape areas
shall consist only of landscaping. The selection and location of turf,
ground cover (including shrubs, grasses, perennials, flowerbeds and
slope retention), and pedestrian paving and other landscaping elements
shall be used to prevent erosion and meet the functional and visual
purposes such as defining spaces, accommodating and directing circulation
patterns, managing visibility, attracting attention to building entrances
and other focal points, and visually integrating buildings with the
landscape area and with each other.
a) Turf grass.
High-use areas shall be planted with irrigated
turf grass. Nonirrigated shortgrass prairie grasses or other adapted
grasses that have been certified as Xeriscape landscaping may be established
in remote, low-use, low-visibility areas.
b) Planting beds.
Shrub and ground cover planting beds
shall be separated from turf grass with edging and shall have open
surface areas covered with mulch.
c) Slopes.
Retaining walls, slope revetment or other acceptable
devices integrated with plantings shall be used to stabilize slopes
that are steeper than 3:1. If soil tests performed on the subject
soils indicate steeper slopes are stable without the above required
protection, then the maximum slope allowed without the above required
protection may be increased to the maximum stated in the soils report
or 2:1, whichever is less steep.
d) Agricultural Use.
If outdoor space is maintained in
active agricultural use, the landscape surfaces and ground cover standards
above shall not apply.
E. Water
Conservation
1. All
landscaping plans shall be designed to incorporate water conservation
materials and techniques through application of Xeriscape landscaping
principles. Xeriscape landscaping principles do not include or allow
artificial turf or plants, mulched (including gravel) beds or areas
without landscape plant material, paving of areas not required for
walkways, plazas or parking lots, bare ground, weed covered or infested
surfaces or any landscaping that does not comply with the standards
of this section. Xeriscape landscaping principles shall be:
a) grouping plants with similar water requirements together on the same
irrigation zones;
b) limiting high-irrigation turf and plantings to appropriate high-use
areas with high visibility and functional needs;
c) use of low-water-demanding plants and turf where practicable;
d) use of efficient irrigation systems;
e) incorporation of soil improvements;
g) provision of regular and attentive maintenance.
F. Plant
Materials.
Trees (Large Shade)
|
---|
Common Name
|
Botanical Name
|
Size
|
Remarks
|
---|
Oak, Burr
|
Quercus macrocarpa
|
80' h
80' w
|
Native
|
Oak, Chinkapin
|
Quercus muhlenbergii
|
80' h
80' w
|
Native
|
Oak, Live*
|
Quercus virginiana
|
90' h
90' w
|
Native
|
Oak, Red
|
Quercus shumardii
|
80' h
60' w
|
Native
|
Pecan
|
Carya illinoinensis
|
100' h
100' w
|
Native
|
Trees (Medium Shade)
|
---|
Common Name
|
Botanical Name
|
Size
|
Remarks
|
---|
Ash, Texas
|
Fraxinus texensis
|
50' h
40' w
|
Native
|
Bald Cypress*
|
Taxodium distichum
|
80' h
50' w
|
Native
|
Elm, Cedar
|
Ulmus crassifolia
|
90' h
80' w
|
Native
|
Elm, Allee Lacebark
|
Ulmus pariviforia ‘Elmer II’
|
75' h
50' w
|
Adapted
|
Elm, Bosque Lacebark
|
Ulmus parivifoia ‘UPMTFI’
|
60' h
40' w
|
Adapted
|
Magnolia, Southern
|
Magnolia grandiflora
|
60' h
30' w
|
Native E. TX
|
Maple, Bigtooth
|
Acer grandidentatum
|
50' h
40' w
|
Native E. TX
|
Maple, Caddo
|
Acer saccharum ‘Caddo’
|
60' h
30' w
|
Native
|
Persimmon, Common
|
Diospyros virginiana
|
60' h
30' w
|
Native
|
Pistachio, Chinese
|
Pistacia chinensis
|
70' h
50' w
|
Adapted
|
Black Locust
|
Robinia pseudoacacia
|
40' h
40' w
|
Adapted
|
Trees (Small Ornamental)
|
---|
Common Name
|
Botanical Name
|
Size
|
Remarks
|
---|
American Smoke Tree
|
Cotinus obovatus
|
25' h
25' w
|
Native
|
Buckeye, Mexican
|
Ungnadia speciosa
|
20' h
20' w
|
Native
|
Carolina Buckthorn
|
Rhamnus caroliniana
|
15' h
15' w
|
Native
|
Desert Willow
|
Chilopsis linearis
|
30' h
25' w
|
Native
|
Crape Myrtle
|
Lagerstroemia indica
|
25' h
15' w
|
Adapted
|
Dogwood (Roughleaf)
|
Cornus drummondii
|
15' h
15' w
|
Native
|
Eastern Red Cedar
|
Juniperus virginiana
|
40' h
20' w
|
Native
|
Eve’s Necklace
|
Sophora affinis
|
30' h
20' w
|
Native
|
Flameleaf Sumac
|
Rhus lanceolata
|
30' h
20' w
|
Native
|
Goldenball Lead Tree
|
Leucaena retusa
|
25' h
15' w
|
Native
|
Goldenrain Tree
|
Koelreuteria paniculata
|
30' h
20' w
|
Adapted
|
Hawthorn, Washington
|
Crataegus phaenopyrum
|
25' h
15' w
|
Adapted
|
Holly, Yaupon
|
Ilex vomitoria
|
20' h
20' w
|
Adapted
|
Magnolia, ‘Little Gem’
|
Magnolia, ‘Little Gem’
|
15' h
10' w
|
Adapted
|
Maple, Shantung
|
Acer trucatum
|
25' h
20' w
|
Adapted
|
Mexican Plum
|
Prunus Mexicana
|
25' h
20' w
|
Native
|
Oak, Bigelow
|
Quercus sinuate var. breviloba
|
40' h
35' w
|
Native
|
Oak, Lacey
|
Quercus laceyi (Q. glaucoides)
|
35' h
30' w
|
Native
|
Pear, Callery
|
Pyrus calleryana
|
25' h
25' w
|
Adapted
|
Persimmon, Texas
|
Diospyros texana
|
20' h
12' w
|
Native
|
Possumhaw
|
Ilex decidua
|
15' h
8' w
|
Native
|
Rusty Blackhaw
|
Viburnum rufidulum
|
30' h
35' w
|
Native
|
Texas Redbud
|
Cercis Canadensis var. ‘texensis’
|
30' h
30' w
|
Native
|
Trees (Living Screen)
|
---|
Common Name
|
Botanical Name
|
Size
|
Remarks
|
---|
Arizona Cypress
|
Cupressus arizonica
|
40' h
20' w
|
Adapted
|
Eastern Red Cedar
|
Juniperus virginiana
|
40' h
20' w
|
Native
|
Holly, Burford
|
Ilex cornuta ‘burfordii’
|
20' h
15' w
|
Adapted
|
Holly, Foster
|
Ilex x attenuata ‘Foster’
|
20' h
10' w
|
Adapted
|
Holly, Nellie R Stevens
|
Ilex x ‘Nellie Stevens’
|
25' h
15' w
|
Adapted
|
Holly, Youpon
|
Ilex vomitoria
|
20' h
20' w
|
Native
|
Magnolia, ‘Little Gem’
|
Magnolia ‘Little Gem’
|
15' h
10' w
|
Adapted
|
Mahonia, Leather Leaf
|
Mahonia bealei
|
7' h
5' w
|
Adapted
|
Myrtle, Wax
|
Myrica cerifera
|
15' h
10' w
|
Native
|
Pine, Mondell
|
Pinus eldarica
|
40' h
20' w
|
Adapted
|
Shrubs
|
---|
Common Name
|
Botanical Name
|
Size
|
Remarks
|
---|
Abelia
|
Abelia grandiflora
|
4' h
4' w
|
Native
|
Agarito
|
Berberis trifoliate
|
10' h
10' w
|
Native
|
American Beautyberry
|
Calicarpa Americana
|
5' h
5' w
|
Native
|
Apache Plume
|
Fallugia paradoxa
|
6' h
6' w
|
Native
|
Aromatic Sumac
|
Rhus aromatic
|
6' h
6' w
|
Native
|
Black Dalea
|
Dalea frutescens
|
4' h
4' w
|
Native
|
Damianita
|
Compositae Chrysactinia Mexicana
|
2' h
2' w
|
Native
|
Desert Spoon
|
Dasylirion wheeleri
|
3' h
3' w
|
Native
|
Hawthorn, Indian
|
Raphiolepsis indica
|
3' h
4' w
|
Adapted
|
Holly, Burford
|
Ilex cornuta ‘Burfordii Nana’
|
5' h
5' w
|
Adapted
|
Flame Anisacanthus
|
Anisacanthus q. wrightii
|
4' h
3' w
|
Native
|
Texas Kidneywood
|
Eysenhardtia texana
|
12' h
8' w
|
Native
|
Red Yucca
|
Hesperaloe parviflora
|
3' h
3' w
|
Native
|
Texas Sage, Silverado
|
Leucophyllum f. ‘Silverado’
|
4' h
4' w
|
Native
|
Soft-leaf Yucca
|
Yucca recurvifolia
|
5' h
5' w
|
Native
|
Twist-leaf Yucca
|
Yucca rupcola
|
5' h
5' w
|
Native
|
Grass/Turf
|
---|
Common Name
|
Botanical Name
|
Size
|
Remarks
|
---|
Big Blue Stem
|
Andropogon gerardii
|
5' h
5' w
|
Native
|
Blue Grama
|
Bouteloua gracilis
|
Turf/Sod
|
Native
|
Buffalograss
|
Buchloe dactyloides
|
Turf/Sod
|
Native
|
Bermuda grass
|
Cynodon dactylon
|
Turf/Sod
|
Adapted
|
Eastern Gamagrass
|
Tripsacum dactyloides
|
4' h
3' w
|
Native (Seed)
|
Green Sprangletop
|
Leptochloa dubia
|
3' h
3' w
|
Native
|
Muhly, Seep
|
Muhlenbergia reverchonii
|
2' h
2' w
|
Native
|
Muhly, Deer
|
Muhlenbergia rigens
|
3' h
3' w
|
Native
|
Muhly, Lindheimer
|
Muhlenbergia lindheimeri
|
4' h
2' w
|
Native
|
Indian Grass
|
Sorghastrum nutans
|
4' h
3' w
|
Native
|
Little Blue Stem
|
Schizachyrium scoparium
|
5' h
2' w
|
Native
|
Prairie Dropseed
|
Sporobolus heterolepis
|
5' h
5' w
|
Native
|
Prairie Wild Rye
|
Elymus Canadensis
|
3' h
3' w
|
Native (Seed)
|
Sideoats Grama
|
Bouteloua curipendula
|
3' h
1' w
|
Native
|
Switch Grass
|
Panicum virgatum
|
5' h
5' w
|
Native
|
Groundcover/Vines
|
---|
Common Name
|
Botanical Name
|
Size
|
Remarks
|
---|
Ajuga
|
Ajuga reptans
|
6" h
Creeping
|
Adapted
|
Coral Honeysuckle
|
Lonicera sempervirens
|
Vine
|
Native
|
Crossvine
|
Bignonia capreolata
|
Vine
|
Native
|
Frog Fruit
|
Phyla nodiflora
|
12" h
Spreading
|
Native
|
Horseherb
|
Calyptocarpus vialis
|
10" h
36" w
|
Native
|
Liriope
|
Liriope muscari
|
15" h
12" w
|
Adapted
|
Pigeonberry
|
Rivina humilis
|
18" h
24" w
|
Native
|
Snake Herb
|
Acanthaceae Dyschoriste linearis
|
6" h
18" w
|
Native
|
Trumpet Vine
|
Campsis radicans
|
Vine
|
Native
|
Water Clover
|
Marsilea macropoda
|
8" h
Creeping
|
Native
|
Wooly Stemodia
|
Stemodia lanata
|
5" h
Creeping
|
Native
|
Wood Violet
|
Viola missouriensis
|
6"
Creeping
|
Native
|
Perennials
|
---|
Common Name
|
Botanical Name
|
Size
|
Remarks
|
---|
Angel Trumpet
|
Datura wrightii
|
3' h
3' w
|
Native
|
Autumn Joy Sedum
|
Sedum ‘Autumn Joy’
|
2' h
2' w
|
Adapted
|
Blackeyed Susan
|
Rudbeckia hirta
|
2' h
2' w
|
Native (Seed)
|
Blackfoot Daisy
|
Melampodium leucanthum
|
12" h
12" w
|
Native
|
Blazing Stars
|
Liatris mucronata
|
2' h
2' w
|
Native
|
Brown-eyed Susan
|
Rudbeckia triloba
|
3' h
2' w
|
Native
|
Clasping Coneflower
|
Dracopis amplexicalis
|
2' h
1' w
|
Native (Seed)
|
Chocolate Flower
|
Berlandiera lyrata
|
1' h
2' w
|
Native
|
Cutleaf Daisy
|
Engielmannia pinnatifida
|
3' h
3' w
|
Native (Seed)
|
Fournerve Daisy
|
Hymenoxys scaposa
|
1' h
1' w
|
Native
|
Fall Aster
|
Aster longifolia
|
3' h
3' w
|
Native
|
Globemallow, Scarlet
|
Sphaeralcea coccinea
|
12" h
12" w
|
Native
|
Indian Blanket
|
Gailardia pulchella
|
12" h
2" w
|
Native (Seed)
|
Indian Paint Brush
|
Castilleja indivisa
|
12" h
2" w
|
Native (Seed)
|
Green-headed Cornflower
|
Rudbeckia lanciniata
|
4' h
2' w
|
Native (Seed)
|
Gregg Dalea
|
Dalea greggii
|
1' h
4' w
|
Native
|
Gregg’s Mistflower
|
Eupatorium greggii
|
2' h
1' w
|
Native
|
Illinois Bundleflower
|
Desmanthus inllinoensis
|
2' h
1' w
|
Native (Seed)
|
Maximilian Sunflower
|
Helianthus maximilliani
|
5' h
3' w
|
Native (Seed)
|
Mexican Hat
|
Ratibida columnifera
|
2' h
1' w
|
Native (Seed)
|
Lindheimer’s Senna
|
Senna lindheimeriana
|
3' h
3' w
|
Native
|
Obedient Plant
|
Physostegia virginiana
|
4' h
2' w
|
Native (Seed)
|
Pink Evening Primrose
|
Oenothera speciosa
|
1' h
1' w
|
Native (Seed)
|
Pink Scullcap
|
Scutellaria suffrutescens
|
1' h
1' w
|
Native
|
Plains Coreopsis
|
Coreopsis tinctoria
|
1' h
1' w
|
Native (Seed)
|
Purple Coneflower
|
Echinacea purpurea
|
2' h
2' w
|
Native (Seed)
|
Prairie Verbena
|
Verbena bipinnitfida
|
6" h
18" w
|
Native
|
Rockrose, Brazilian
|
Parvonia brazilliensis
|
3' h
3' w
|
Adapted
|
Rockrose
|
Parvonia lasiopetala
|
3' h
3' w
|
Native
|
Sage, Autumn
|
Salvia Greggii
|
3' h
2' w
|
Native
|
Sage, Big Red
|
Salvia penstemonoides
|
4' h
3' w
|
Native (Seed)
|
Sage, Indigo Spires
|
Salvia longespicata x farinacea
|
4' h
6' w
|
Native
|
Sage, Mealy Blue
|
Salvia farinacea
|
2' h
1' w
|
Native
|
Sage, Pitcher
|
Salvia
|
4' h
3' w
|
Native (Seed)
|
Sage, Russian
|
Perovskia atriplicifolia
|
4' h
3' w
|
Adapted
|
Sage, Scarlet
|
Salvia coccinea
|
3' h
3' w
|
Native (Seed)
|
Skeletonleaf Goldeneye
|
Viguiera stenoloba
|
2' h
2' w
|
Native
|
Sundrops
|
Calylophus drummondianus
|
6" h
12" w
|
Native
|
Texas Betony
|
Stachys coccinea
|
18" h
24" w
|
Native
|
Texas Greeneyes
|
Berlandiera texana
|
4' h
2' w
|
Native
|
Texas Lantana
|
Lantana horrida
|
5' h
5' w
|
Native
|
Texas Star Hibiscus
|
Hibiscus coccinea
|
5' h
3' w
|
Native
|
Turk’s Cap
|
Malvaviscus drummondii
|
4' h
4' w
|
Native
|
Whirling Butterflies
|
Gaura lindheimeri
|
3' h
3' w
|
Native
|
Winecup
|
Callirhoe involucrate
|
1' h
2' w
|
Native
|
Zexmenia
|
Wedelia hispida
|
2' h
Spreading
|
Native
|
(Ordinance 480-14 adopted 11/20/14; Ordinance 494-15, sec. VI, adopted 5/21/15)