City of Sansom Park, TX DEVELOPMENT STANDARDS

§ 7.1 DEVELOPMENT AND CONSTRUCTION STANDARDS.

EXTERIOR CONSTRUCTION STANDARDS, GENERALLY

The following design standards shall apply generally and by use type within the zoning district in which the development is proposed.

Masonry Construction.

This term shall be construed to mean that form of construction composed of brick, stone, decorative concrete block or tile, or other similar building units or materials (or combination of these materials) laid up unit by unit and set in mortar, unless otherwise permitted under this section, and shall exclude wall area devoted to doors and windows. As applicable to meeting minimum requirements for the exterior construction of buildings within each zoning district, this term shall include the following materials:

Hard Fired Brick.

Kiln fired clay or slate material. Brick may include concrete brick if it is to the same ASTM standard for construction as typical hard fired clay brick. Brick shall be severe weather grades; minimum thickness of three (3") inches when applied as a veneer; and shall not include unfired or under-fired clay, sand, or shale brick.

Stone.

Stone shall include naturally occurring granite, marble, limestone, slate, river rock, and other similar hard and durable all-weather stone that is customarily used in exterior building construction. Stone may also include cast-or manufactured-stone product, provided that such product yields a highly textured, stone-like appearance; its coloration is integral to the masonry materials and shall not be painted or sprayed on; and it is demonstrated to be highly durable and maintenance-free. Natural or manmade stone shall have a minimum thickness that meets industry standards.

Decorative Concrete Block.

Decorative Concrete Block shall include highly textured finish, such as split-face, indented, hammered, fluted, ribbed or similar architectural finish. Coloration shall be integral to the masonry material and shall not be painted or sprayed on. Decorative Concrete Block shall have a minimum thickness that meets industry standards when applied as a veneer and shall not include lightweight or featherweight concrete block or cinderblock units. Decorative Concrete Block shall not be used as a material in single-family, duplex, multifamily, or single-family attached structures.

Concrete Pre-Cast or Tilt-Wall Panels.

This material shall only be allowed if a highly textured architectural finish which appears texturally as face brick or stone. Concrete pre-cast or tilt-wall panels may be brick-like or stone-like in appearance. Coloration of the material shall be integral to the masonry material and shall not be painted on or sprayed on. This material shall not include smooth, untextured or inadequately textured finishes. Concrete pre-cast or tilt-wall panels shall not be used as a material in single-family, duplex, multifamily, or single-family attached structures.

Glass Blocks or Tiles.

This material shall be of the type customarily used in exterior building construction. It shall not comprise more than thirty (30%) percent of any exterior wall surface, nor more than twenty (20%) of the building’s total exterior on all wall surfaces combined. It shall not be highly reflective or contain a mirror-like finish.

Stucco.

Stucco or plaster shall only be allowed as a masonry material when applied using a 3-step process over diamond metal lath mesh to a 7/8th inch thickness or by other processes producing comparable stucco finish with equal or greater strength and durability specifications.

Prohibited Materials and colors.

Unless specifically approved by the City Council on an approved site plan for single-family, single-family attached, attached multifamily, institutional, office, retail, commercial, industrial, or other nonresidential structures, the following materials shall not qualify or be defined as “masonry construction” in meeting the minimum requirements for the exterior construction of buildings:

Exterior plaster, adobe or mortar wash, surface materials unless otherwise permitted in this section;

Exterior insulation and finish systems (EIFS), acrylic matrix, synthetic plaster, or other similar synthetic material;

Cementitious fiber board siding (such as “Hardy Plank, Hardy Board, etc.), unless otherwise provided herein;

PVC or other plastic-based siding materials;

Lightweight or featherweight concrete blocks, cinderblocks or other lightweight based masonry unit;

Any other cementitious product not listed above.

Any pastel or bright colors painted directly to the surface of the exterior structure. All structures shall have an exterior color of muted earth tones such as, but not limited to, reds, browns, tans, grays, and greens.

SECTION 7.1.2

MINIMUM DESIGN STANDARDS

The standards and criteria contained within this subsection are deemed to be the minimum standards and shall apply to all new building construction or redevelopment occurring within the City unless otherwise stated in this Ordinance.

Single-Family and Two-Family Residential Zoning Districts

The design standards for all single-family and duplex residential structures within the SF-10, SF-6, SF-5 and D (Duplex) District shall be as follows:

All single-family and two-family (duplex) structures shall be of exterior fire-resistant construction, and shall have a minimum of eighty (80%) percent masonry construction, more or less equally distributed around all sides of the structure, for the first story of the structure, and a minimum of fifty (50%) percent masonry construction, more or less equally distributed around all sides, for any additional story above the first floor.

Areas of a single-family or duplex structure’s facade that are devoted to windows, doors, covered porches or patios that have a minimum size of four feet (4') deep and eight (8') feet wide (thirty-two (32) square feet), chimneys, breezeways, or courtyards shall not be counted as “wall surface” when calculating the masonry requirement.

Prohibited materials.

Concrete, concrete block, vinyl, plastic, or metal exterior construction is not permitted on any single-family or duplex residential structure.

Roof materials

for a single-family or two-family (duplex) structure shall be comprised of an architectural, laminated, dimensional composition shingle (thirty (30) year minimum); Metal roofing with enamel baked finish or architectural grade metal roofing products which are stamped to appear as wood shakes, dimensional shingles, wood shingles, slate or tile; or terra-cotta or slate tile. All unfinished metal roofing is prohibited. Acceptable colors are: Earth tones are defined as a color scheme that draws from a color palette of browns, tans, warm grays, and greens. The colors in an earth tone scheme are muted and flat in an emulation of the natural colors found in dirt, moss, trees and rocks, and the color pallet [palette] found in the manufacture’s metal roofing with enamel baked finish. If roof is not visible to the public, there is no pitch requirement (i.e. parapet roof); if roof is visible to the public a minimum 6:12 pitch is required.

Chimney Stacks.

All chimney stacks for single-family or duplex structures shall be of one hundred (100%) percent masonry construction or may be constructed of cementitious fiber board.

Elevation articulation.

The elevation of a single-family or duplex structure, including garages facing the street shall contain at least one section of at least twenty (20%) percent of the total street elevation that is offset at least two (2') feet from the remainder of the street elevation.

Nonresidential buildings.

Any nonresidential building constructed within any residential zoning districts shall conform to the design standards of Section 7.1.4 below.

Newly Constructed Single-Family Dwelling Required Architectural Features.

All newly constructed single-family dwellings are required to comply with the following architectural features:

Garage spaces for a minimum of two (2) vehicles shall be attached to the primary structure and shall be located behind the required building setback lines;

Wood or stained fiberglass or metal simulated wood grain front door;

No Facade may be repeated within any adjacent lots or across the street from those lots within groupings of five (5) homes;

Concealed HVAC units, trash storage and utility meters;

If brick is used, brick shall be properly detailed. Brick shall be coursed exactly to the top and bottom of all wall openings;

Windows shall be single hung, double hung, triple hung, or casement;

Flush mounted windows are prohibited;

Windows are to be placed on each wall elevation with a wall-to-window ratio that meets the light and air requirements of the building code;

If shutters are used, shutters shall be one-half the width of, and the same height of the associated opening. All shutters shall be louvered, paneled, or constructed of boards as appropriate to the style of the building. Shutters do not need to be operable;

Gutters shall be copper, galvanized steel, aluminum or painted if exposed;

Dormers shall not use siding as window jamb material;

The body of a single-window dormer shall be vertically proportioned or square;

If chimneys are visible, they shall have a projecting cap;

If chimneys are located on a street facing wall, they shall extend to the ground;

If a porch is used, the porch column base shall not protrude beyond the bottom edge of the porch flooring.

Additional Newly Constructed Single-Family Dwelling Architectural Features.

All newly constructed single-family dwellings shall contain at least four (4) of the following architectural features:

Stoop and portico at the front door

Front porch

Front porch or front stoop steps and railing

Front porch roof

Decorative or architectural porch railing

Second story porch

If brick or stucco is used, a stone base below first floor window shall be installed

Trim at gable rake

Decorative roof finials or ornamentation

10.

Decorative attic or gable feature greater than 3 SF in size

11.

Trim at windows and doors of the street facade

12.

Arched window head or heads (depending on architectural style) on street facade

13.

Dormer with window

14.

Window shutters on street facade

15.

Divided light windows

16.

Decorative concrete driveway

SECTION 7.1.3

MULTIFAMILY RESIDENTIAL ZONING DISTRICT STANDARDS

The design standards for all multifamily and single-family attached structures within the Multifamily (MF) zoning district shall be as follows:

All multifamily and single-family attached residential structures shall be of exterior fire-resistant construction and shall have a minimum of eighty (80%) percent masonry construction, more or less equally distributed around all sides of the structure, for the first story of the structure, and a minimum of fifty (50%) percent masonry construction, more or less equally distributed around all sides, for any additional story above the first floor.

Areas of a multifamily and single-family attached residential structure’s facade that are devoted to windows, doors, covered porches or patios that have a minimum size of (4') feet deep and eight (8') feet wide (thirty [thirty-two] (32) square feet), chimneys, breezeways, or courtyards shall not be counted as “wall surface” when calculating the masonry requirement.

Prohibited materials.

Concrete, concrete block, vinyl, plastic or metal exterior construction is not permitted on any multifamily or single-family attached structure.

Roof materials.

Roof materials for a multifamily and single-family attached residential structures shall be comprised of an architectural, laminated, dimensional composition shingle (thirty (30) year minimum); flat pan standing seam metal roofing, or architectural grade metal roofing products which are stamped to appear as wood shakes, dimensional shingles, wood shingles, slate or tile; or terra-cotta or slate tile. Sheetmetal or corrugated metal roofing materials is prohibited. Roofs shall be earth tones. Earth tones are defined as a color scheme that draws from a color palette of browns, tans, warm grays, and greens. The colors in an earth tone scheme are muted and flat in an emulation of the natural colors found in dirt, moss, trees and rocks. If roof is not visible to the public, there is no pitch requirement (i.e. parapet roof); if roof is visible to the public a minimum 6:12 pitch is required.

Accessory structures.

Accessory structures, regardless of size, within the multifamily (MF) zoning district shall conform to the minimum exterior construction standards for the main building on the lot, tract, [or] site, and shall be architecturally compatible with the main building.

Separation of Multifamily Buildings:

Buildings two stories or less in height with opposite walls that:

Contain openings for windows, light and air ventilation shall be separated by fifteen (15) feet between building walls;

Contain no openings shall be separated by ten (10) feet between buildings walls.

Buildings more than two stories in height with opposite walls that:

Contain openings for windows, light and air ventilation shall be separated by (20) feet between building walls;

Contain no openings shall be separated by fifteen (15) feet between building walls.

SECTION 7.1.4

NONRESIDENTIAL ZONING DISTRICT STANDARDS

The design standards for all nonresidential and institutional structures within the Office Neighborhood Service (O), Commercial (C), and Industrial (I) zoning districts, and for nonresidential structures located within all other districts shall be as follows:

All nonresidential and institutional structures in any zoning district, shall have a minimum of seventy-five (75%) percent masonry construction, more or less equally distributed around all sides of the building, for the first story defined as below the first floor ceiling plate, and a minimum of fifty (50%) for any story above. Any facade that faces, or is visible from a public street, shall have a minimum of seventy-five (75%) percent masonry construction, and all other facades shall be comprised of not less than fifty (50%) percent masonry construction.

Areas of a nonresidential or institutional structure’s facade that are devoted to windows, doors, covered porches or stoops, breezeways or courtyards shall not be counted as “wall surface” when calculating the masonry requirement.

Metal exterior material use.

Metal exterior construction is prohibited on any nonresidential or institutional structure which is located within any zoning district, save and except the following:

Structures located on a through lot that both fronts and backs onto a public street. The rear facade, which must be located equal to or more than one thousand (1,000') feet from the public street, may use metal exterior construction upon approval of the Site Plan by the City Council, and;

Upon approval of the Site Plan by the City Council, nonresidential and institutional structures within any of the nonresidential zoning districts may use metal as an exterior material on up to twenty (20%) percent of the facade as an architectural accent.

The use of any type of metal for exterior building construction shall be clearly shown on the Site Plan and shall only be allowed with the Site Plan approval. The exterior finish of metal used in exterior construction shall be permanent, maintenance-free nature such as a baked-on finish unless approved otherwise on the Site Plan. The use of corrugated, galvanized, aluminum-coated, zinc-coated unfinished, or similar metal surfaces shall be prohibited unless approved otherwise on the Site Plan.

Roof materials.

Any roof materials for a nonresidential or institutional structure that are visible from a public street shall be shall be comprised of an architectural, laminated, dimensional composition shingle (thirty (30) year minimum); flat pan standing seam metal roofing, or architectural grade metal roofing products which are stamped to appear as wood shakes, dimensional shingles, wood shingles, slate or tile; or terra-cotta or slate tile. Sheetmetal or corrugated metal roofing materials is prohibited. Roofs shall be earth tones. Earth tones are defined as a color scheme that draws from a color palette of browns, tans, warm grays, and greens. The colors in an earth tone scheme are muted and flat in an emulation of the natural colors found in dirt, moss, trees and rocks. If roof is not visible to the public, there is no pitch requirement (i.e. parapet roof); if roof is visible to the public a minimum 6:12 pitch is required. Nonresidential or institutional structures with a flat roof shall have highly articulated parapet that conceals the roof and any roof-mounted mechanical equipment.

Structural exceptions to masonry standards.

The following structures are exempt from the masonry construction requirements.

Barns located on the lots of four (4) acres or more provided that such barns are used solely for agricultural purposes (as distinguished from commercial purposes).

Mobile homes and HUD-Code manufactured homes lawfully existing are not subject to the masonry requirements.

Temporary construction buildings, field offices, sales offices and temporary classrooms or storage buildings for the public school. The exception shall be only provided that such facilities are legally permitted by the City for a specific period of time, and provided that they are completely removed from the premises upon expiration of the permit or upon completion of construction, whichever occurs first.

Residential and nonresidential structures legally in existence as of (date of this ordinance), and any additions to such structures that do not cumulatively exceed twenty (20%) percent of the original building size (as it existed on date of this ordinance). Such additions shall be allowed to be constructed of the same exterior materials as the original building.

Use of Alternative Exterior Materials.

All written requests for the use of alternative exterior building materials to include alternative roof material and/or roofing color and alternative roof pitch shall be clearly noted and described in detail on a color rendering of the structure’s elevation that is submitted along with the site plan for approval. The use of alternative exterior building materials, roof pitch and roof materials and/or color may only be requested for multifamily, single-family attached and nonresidential structures. The City may require submissions of an actual sample(s) of the proposed exterior finish material(s) along with the elevation(s) and the site plan.

The City Council may approve, all alternative exterior construction material(s), roof pitch and roof materials and/or color if it is determined to be equivalent or better than the exterior materials, roof pitch, or roof materials and/or colors otherwise required by this Subsection and the City’s Building Code as part of the site plan approval process.

Consideration for exceptions to the above exterior construction requirements shall be based only upon the following:

Architectural design, creativity and innovation;

Compatibility with surrounding structures;

Relative ease of maintenance of the material(s);

Long-term durability and weather-resistance of the materials(s); and

Long-term stability in property value due to the high quality of the material(s).

(Ordinance 480-14 adopted 11/20/14; Ordinance 521-17 adopted 4/20/17; Ordinance 552-19 adopted 4/18/19)

§ 7.2 SCREENING AND FENCING.

SECTION 7.2.1

SCREENING WALLS AND FENCES

General Requirements

A permit shall be required for any new fence or screening wall construction or replacement of an existing fence or screening wall unless otherwise provided in this Ordinance. No permit shall be required to repair a fence as long as the repair keeps the fence in the same location and utilizes the same materials.

All fences and screening walls shall be kept in good repair and shall not create blight. Dilapidated fences or screening walls shall be repaired or replaced in accordance with provisions of this section. Wood fences shall be painted or stained with natural wood colors on both sides.

No fence or screening wall shall exceed eight (8) feet in height, as measured from the grade of the property, unless otherwise approved by the City Council during the site plan process or by way of a variance in accordance with Section 3.2.6.

Reserved.

Chain-link fencing not clad in vinyl may be allowed for fencing of dog runs, tennis courts, swimming pools and similar purposes if it is completely contained on the lot, not on the perimeter, and it is not directly visible from any street or adjacent property.

Temporary fencing used for construction purposes or special events shall be exempt from the requirements of this section provided that such fencing is approved as part of the applicable building permit or special events permit.

Any variances to the requirements of this section shall be considered by the BOA unless otherwise provided in this Ordinance.

Fencing Requirements for Agricultural Uses

The following standards apply to tracts of land with four (4) acres or more used for agricultural or animal husbandry purposes in accordance with this Ordinance.

Pipe fencing, split rail fencing, barbed wire, hog wire, chicken wire, chain-link, cable, and other open style types of fencing traditionally used in agriculture and animal husbandry shall be allowed. Such fencing may be located up to the right-of-way line and shall not exceed eight (8) feet in height. Solid style types of fencing shall meet the fence height and setback requirements for residential uses. Open style fencing typically used in wildlife management may exceed eight (8) feet in height as necessary for the purposes of wildlife management.

No permit is required for agricultural fencing.

Electric Fences

An electric fence is allowed on properties exceeding 20 acres in all zoning districts, with proof submitted to the electrical inspector that the fence will be designed to retain animals, be inaccessible to the general public and not pose a hazard to life.

An electric fence is allowed in association with a permitted nonresidential outdoor storage area in the Industrial “I” zoning districts subject to the following standards.

Unless otherwise specified in this Section, electric fences must be installed in conformance with the specifications set forth in the City’s electrical code and the International Electroctechnical Commission Standard No. 60335-2-76. In addition, the electric fence controller must meet the requirements of Underwriters Laboratories Standard UL69, Electric-Fence Controller, and labeled as such.

The electric fence controller and emergency entry key safe for the electric fence must be located in a single accessible location for the entire fence.

The electric fence must be surrounded by a nonelectrical fence or wall six to eight feet in height.

The electric fence must be installed a minimum of one foot from the surrounding nonelectric fence or wall, except along the gate. Along the gate, the electric fence must be installed a minimum of three inches from the surrounding nonelectric fence or wall.

The electric fence must be clearly identified with warning signs at intervals of not less than sixty (60) feet.

The electric fence must only be energized during hours when the public does not have legal access to the protected property.

Prohibited Materials.

Permits shall not be issued for materials not manufactured specifically for fencing, such as fibrous masonry products, landscape timbers, railroad ties, latticework panels, plywood, corrugated steel panels, metal sheets or fiberglass panels. Other prohibited material include[s] razor wire fencing.

Fencing Requirements for Residential Uses

Fences shall be constructed of wood, ornamental metal (i.e. wrought iron), tubular steel, masonry, or other materials traditionally used in private fence construction. New and innovative materials such as plastics, PVC’s, metal panel or slat, cementitious fiberboard, and other similar materials may be approved for use by the City Council if the material is compatible in character with traditional residential fencing and proven to be sturdy, durable and relatively maintenance-free.

The maximum height, as measured from the grade of the property, shall be as follows:

Restrictions and requirements for a fence, wall and barrier are as follows:

Fences in front yard – No fence, wall or barrier may be built within the required front yard as established by the zoning regulations of the City of Sansom Park except as follows:

(A)

Required Setbacks on Residential Lots –

A fence may be erected in the front yard, as established by the zoning regulations of the City of Sansom Park, of a residential lot only if the following criteria are met:

The fence shall not exceed four (4) feet in height above the adjacent grade;

ii.

The fence shall be constructed to provide that a minimum of 50% of the fence is open;

iii.

On corner lots the fence shall not be located within the designated visibility triangle; and

iv.

The fence shall be constructed of wood, wrought iron, plastic or similar fencing materials[.]

Maximum of eight (8) feet for side or rear yards.

Fencing in the front yard of a residential lot shall be located no closer than three (3) feet (measured inside the residential lot) to the right-of-way line.

Gates designed for vehicular access shall be set back from the right-of-way line a minimum of twenty-four (24) feet.

The height of a fence adjacent or perpendicular to a screening wall shall not exceed the height of the subdivision’s screening wall or any other fence constructed by the developer at the time of initial development.

All fences adjacent to parks, trails, or designated open spaces shall be constructed of split rail, ornamental metal, tubular steel, masonry columns, or similar open face material and not exceed a height of six (6) feet. No wood fencing shall be allowed behind the required open space. Solid fencing constructed of Cedar (with metal posts and Cedar top and bottom caps and stained with wood sealant) or masonry material may be allowed if adjacent to a park or open space area that is used actively such as a public swimming pool, sport facility, etc.

Allowable wood fences adjacent to streets, schools, parks, open spaces or other public spaces shall have the finished side facing the public space. All fence posts and structural components shall be placed on the interior of the lot.

All fence posts and structural components shall be placed on the interior of the lot.

The location of fences for double frontage lots or corner lots adjacent to a street shall be in accordance with the building setback line as shown on the final plat. If a property is not platted or if no building line is shown on the recorded plat, the location of fences shall comply with the building setback requirements of the zoning district that the property is located in.

10.

If a corner lot is adjacent to a subdivision’s screening wall, a fence may be placed outside the required setback line to connect with the screening wall.

11.

Fences for nonresidential uses allowed in residential zoning districts such as schools or Churches shall meet the fencing standards for nonresidential districts.

Fencing Requirements for Swimming Pools

Swimming pools shall have a fence that shall conform to the requirements of the International Building Code.

Fencing and Screening Wall Requirements for Multifamily and Nonresidential Uses

Fencing shall not exceed six (6) feet in height.

Fencing shall be constructed of wrought iron, tubular steel, masonry, live screening, or a combination thereof unless adjacent to single-family dwellings, or two-family dwellings, in which a screening wall shall be constructed and shall be made of masonry materials with masonry columns placed a minimum of thirty-two (32) foot on center. Wood, barbed wire, and chain-link fencing is prohibited.

All fencing and screening walls for multifamily and nonresidential developments shall be identified on the site plan for the development and approved as part of the site plan approval.

The City Council may approve alternative fencing materials and construction standards to any of these requirements as a part of the site plan approval process when required.

Screening walls shall be constructed of masonry material such as brick, stone, concrete panels, or similar materials consistent in material, finish, and color with the primary buildings within the development or adjacent buildings in the area. The wall finish shall be consistent on both sides.

Screening walls shall be a minimum of six (6) feet in height and a maximum of eight (8) feet in height on properties adjacent to single-family and two-family residential districts. This screening wall shall be constructed prior to issuance of a building permit for any structure on the multifamily or nonresidential use property and shall be maintained by the owner of the property used for multifamily or nonresidential use.

Screening wall plans shall be submitted to the City for review and permitting and shall be signed and sealed by a Structural or Civil Engineer licensed by the State of Texas.

All uses which require storage such as, but not limited to, auto impound lots, wrecking services, contractor yards, and other facilities shall provide the storage of such items to be within completely enclosed buildings or effectively screened with screening walls or fences not less than six (6) feet in height nor more than eight (8) feet in height, provided no storage located within fifty (50) feet of such screening shall exceed the maximum height of such screening.

(Ordinance 480-14 adopted 11/20/14; Ordinance 494-15, sec. 5, adopted 5/21/15; Ordinance 500-16 adopted 1/21/15)

§ 7.3 LANDSCAPING.

Applicability.

This Section shall apply to all new nonresidential and multifamily development within the City of Sansom Park.

Purpose.

The purpose of this section is to encourage low maintenance landscaping, water conservation and tree preservation while providing guidelines for minimum landscaping for new development throughout the City, preserving the natural, open character of the Rural Residential areas, and not prohibiting the normal use of properties for agricultural purposes.

Nonresidential and Multifamily landscaping.

These standards apply to new nonresidential and multifamily developments. These standards may be met either by saving existing trees on the site, or planting new trees from the recommended list.

A twenty (20') foot linear landscape strip shall be provided adjacent to all public streets. The landscape strip shall include a minimum of one (1) shade tree (two and one-half inch caliper minimum) for every fifty (50) linear feet of street frontage.

Where parking lots and drives abut the landscape strip along a street right-of-way, a continuous hedge of evergreen shrubs shall be provided to screen those areas from the street. The shrubs must be a minimum of a ten-gallon size at planting with a minimum mature height of three (3) feet. Shrubs shall be planted according to the spacing recommended for their species. The screening shall extend along the entire street frontage of the parking lot, exclusive of driveways and visibility clips. A landscape berm may be provided in lieu of the screening hedge. The berm must be a minimum of thirty-six (36) inches above the average grade of the street and parking lot curbs with a slope not to exceed 3:1.

Landscaping shall also be provided for the interior parking areas. Trees shall be planted in each parking lot to attain a minimum average density of one (1) shade tree (two and one-half inch caliper minimum) for each ten (10) parking spaces provided, or any fraction thereof. The planting area per tree shall be a minimum of nine (9') feet wide and twenty (20') feet deep.

Interior parking lot landscaping shall include a minimum eight (8%) percent open space. To calculate the total parking area and the subsequent percentage of required interior lot landscaping, total the square footage of parking spaces, planting islands, curbed areas and all interior driveways and aisles. Landscaped areas located contiguous to and within five (5') feet of the parking lot may be used to meet the interior landscaping requirement. Landscaped areas located greater than five (5') feet away from the parking lot may not be used to meet the interior landscaping requirement.

The required landscaping for parking lots shall be more or less evenly distributed throughout the parking lot, although adjustments may be approved by the City Manager or his/her designee where the shape or size of the parking lot, the location of existing trees or other natural constraints reasonably prevent such distribution.

Except for customer and employee parking, parking lot landscape requirements do not apply to storage or standing parking spaces incidental to uses, such as sales and rental of motor vehicles, mobile homes, boats, trailers or other similar uses.

All landscaped areas, including the permeable areas and drip lines around trees and planting beds used for visual screening which abut any parking lot or vehicular travel area, shall be protected with curbs sufficient to protect them from vehicular intrusion.

Foundation Plantings.

Exposed sections of building walls that are in high-use or high-visibility areas of the building exterior shall have planting beds at least five (5) feet wide placed directly along at least fifty (50) percent of such walls.

An automatic irrigation system is required for all landscaping. Irrigation systems shall be designed and installed with rain sensors and low gallonage, low angle nozzles in such a way as to avoid water overflow into the street. A freeze sensor shall be placed in each controller to prevent the irrigation system from activating to create unsafe spillage on roads and/or sidewalks.

Nonresidential Area Treatment

Landscape areas shall include all areas on the site that are not covered by buildings, structures, paving or impervious surface. Landscape areas shall consist only of landscaping. The selection and location of turf, ground cover (including shrubs, grasses, perennials, flowerbeds and slope retention), and pedestrian paving and other landscaping elements shall be used to prevent erosion and meet the functional and visual purposes such as defining spaces, accommodating and directing circulation patterns, managing visibility, attracting attention to building entrances and other focal points, and visually integrating buildings with the landscape area and with each other.

Turf grass.

High-use areas shall be planted with irrigated turf grass. Nonirrigated shortgrass prairie grasses or other adapted grasses that have been certified as Xeriscape landscaping may be established in remote, low-use, low-visibility areas.

Planting beds.

Shrub and ground cover planting beds shall be separated from turf grass with edging and shall have open surface areas covered with mulch.

Slopes.

Retaining walls, slope revetment or other acceptable devices integrated with plantings shall be used to stabilize slopes that are steeper than 3:1. If soil tests performed on the subject soils indicate steeper slopes are stable without the above required protection, then the maximum slope allowed without the above required protection may be increased to the maximum stated in the soils report or 2:1, whichever is less steep.

Agricultural Use.

If outdoor space is maintained in active agricultural use, the landscape surfaces and ground cover standards above shall not apply.

Water Conservation

All landscaping plans shall be designed to incorporate water conservation materials and techniques through application of Xeriscape landscaping principles. Xeriscape landscaping principles do not include or allow artificial turf or plants, mulched (including gravel) beds or areas without landscape plant material, paving of areas not required for walkways, plazas or parking lots, bare ground, weed covered or infested surfaces or any landscaping that does not comply with the standards of this section. Xeriscape landscaping principles shall be:

grouping plants with similar water requirements together on the same irrigation zones;

limiting high-irrigation turf and plantings to appropriate high-use areas with high visibility and functional needs;

use of low-water-demanding plants and turf where practicable;

use of efficient irrigation systems;

incorporation of soil improvements;

use of mulches;

provision of regular and attentive maintenance.

Plant Materials.

Trees (Large Shade)
Common Name	Botanical Name	Size	Remarks
Oak, Burr	Quercus macrocarpa	80' h 80' w	Native
Oak, Chinkapin	Quercus muhlenbergii	80' h 80' w	Native
Oak, Live*	Quercus virginiana	90' h 90' w	Native
Oak, Red	Quercus shumardii	80' h 60' w	Native
Pecan	Carya illinoinensis	100' h 100' w	Native

Trees (Medium Shade)
Common Name	Botanical Name	Size	Remarks
Ash, Texas	Fraxinus texensis	50' h 40' w	Native
Bald Cypress*	Taxodium distichum	80' h 50' w	Native
Elm, Cedar	Ulmus crassifolia	90' h 80' w	Native
Elm, Allee Lacebark	Ulmus pariviforia ‘Elmer II’	75' h 50' w	Adapted
Elm, Bosque Lacebark	Ulmus parivifoia ‘UPMTFI’	60' h 40' w	Adapted
Magnolia, Southern	Magnolia grandiflora	60' h 30' w	Native E. TX
Maple, Bigtooth	Acer grandidentatum	50' h 40' w	Native E. TX
Maple, Caddo	Acer saccharum ‘Caddo’	60' h 30' w	Native
Persimmon, Common	Diospyros virginiana	60' h 30' w	Native
Pistachio, Chinese	Pistacia chinensis	70' h 50' w	Adapted
Black Locust	Robinia pseudoacacia	40' h 40' w	Adapted

Trees (Small Ornamental)
Common Name	Botanical Name	Size	Remarks
American Smoke Tree	Cotinus obovatus	25' h 25' w	Native
Buckeye, Mexican	Ungnadia speciosa	20' h 20' w	Native
Carolina Buckthorn	Rhamnus caroliniana	15' h 15' w	Native
Desert Willow	Chilopsis linearis	30' h 25' w	Native
Crape Myrtle	Lagerstroemia indica	25' h 15' w	Adapted
Dogwood (Roughleaf)	Cornus drummondii	15' h 15' w	Native
Eastern Red Cedar	Juniperus virginiana	40' h 20' w	Native
Eve’s Necklace	Sophora affinis	30' h 20' w	Native
Flameleaf Sumac	Rhus lanceolata	30' h 20' w	Native
Goldenball Lead Tree	Leucaena retusa	25' h 15' w	Native
Goldenrain Tree	Koelreuteria paniculata	30' h 20' w	Adapted
Hawthorn, Washington	Crataegus phaenopyrum	25' h 15' w	Adapted
Holly, Yaupon	Ilex vomitoria	20' h 20' w	Adapted
Magnolia, ‘Little Gem’	Magnolia, ‘Little Gem’	15' h 10' w	Adapted
Maple, Shantung	Acer trucatum	25' h 20' w	Adapted
Mexican Plum	Prunus Mexicana	25' h 20' w	Native
Oak, Bigelow	Quercus sinuate var. breviloba	40' h 35' w	Native
Oak, Lacey	Quercus laceyi (Q. glaucoides)	35' h 30' w	Native
Pear, Callery	Pyrus calleryana	25' h 25' w	Adapted
Persimmon, Texas	Diospyros texana	20' h 12' w	Native
Possumhaw	Ilex decidua	15' h 8' w	Native
Rusty Blackhaw	Viburnum rufidulum	30' h 35' w	Native
Texas Redbud	Cercis Canadensis var. ‘texensis’	30' h 30' w	Native

Trees (Living Screen)
Common Name	Botanical Name	Size	Remarks
Arizona Cypress	Cupressus arizonica	40' h 20' w	Adapted
Eastern Red Cedar	Juniperus virginiana	40' h 20' w	Native
Holly, Burford	Ilex cornuta ‘burfordii’	20' h 15' w	Adapted
Holly, Foster	Ilex x attenuata ‘Foster’	20' h 10' w	Adapted
Holly, Nellie R Stevens	Ilex x ‘Nellie Stevens’	25' h 15' w	Adapted
Holly, Youpon	Ilex vomitoria	20' h 20' w	Native
Magnolia, ‘Little Gem’	Magnolia ‘Little Gem’	15' h 10' w	Adapted
Mahonia, Leather Leaf	Mahonia bealei	7' h 5' w	Adapted
Myrtle, Wax	Myrica cerifera	15' h 10' w	Native
Pine, Mondell	Pinus eldarica	40' h 20' w	Adapted

Shrubs
Common Name	Botanical Name	Size	Remarks
Abelia	Abelia grandiflora	4' h 4' w	Native
Agarito	Berberis trifoliate	10' h 10' w	Native
American Beautyberry	Calicarpa Americana	5' h 5' w	Native
Apache Plume	Fallugia paradoxa	6' h 6' w	Native
Aromatic Sumac	Rhus aromatic	6' h 6' w	Native
Black Dalea	Dalea frutescens	4' h 4' w	Native
Damianita	Compositae Chrysactinia Mexicana	2' h 2' w	Native
Desert Spoon	Dasylirion wheeleri	3' h 3' w	Native
Hawthorn, Indian	Raphiolepsis indica	3' h 4' w	Adapted
Holly, Burford	Ilex cornuta ‘Burfordii Nana’	5' h 5' w	Adapted
Flame Anisacanthus	Anisacanthus q. wrightii	4' h 3' w	Native
Texas Kidneywood	Eysenhardtia texana	12' h 8' w	Native
Red Yucca	Hesperaloe parviflora	3' h 3' w	Native
Texas Sage, Silverado	Leucophyllum f. ‘Silverado’	4' h 4' w	Native
Soft-leaf Yucca	Yucca recurvifolia	5' h 5' w	Native
Twist-leaf Yucca	Yucca rupcola	5' h 5' w	Native

Grass/Turf
Common Name	Botanical Name	Size	Remarks
Big Blue Stem	Andropogon gerardii	5' h 5' w	Native
Blue Grama	Bouteloua gracilis	Turf/Sod	Native
Buffalograss	Buchloe dactyloides	Turf/Sod	Native
Bermuda grass	Cynodon dactylon	Turf/Sod	Adapted
Eastern Gamagrass	Tripsacum dactyloides	4' h 3' w	Native (Seed)
Green Sprangletop	Leptochloa dubia	3' h 3' w	Native
Muhly, Seep	Muhlenbergia reverchonii	2' h 2' w	Native
Muhly, Deer	Muhlenbergia rigens	3' h 3' w	Native
Muhly, Lindheimer	Muhlenbergia lindheimeri	4' h 2' w	Native
Indian Grass	Sorghastrum nutans	4' h 3' w	Native
Little Blue Stem	Schizachyrium scoparium	5' h 2' w	Native
Prairie Dropseed	Sporobolus heterolepis	5' h 5' w	Native
Prairie Wild Rye	Elymus Canadensis	3' h 3' w	Native (Seed)
Sideoats Grama	Bouteloua curipendula	3' h 1' w	Native
Switch Grass	Panicum virgatum	5' h 5' w	Native

Groundcover/Vines
Common Name	Botanical Name	Size	Remarks
Ajuga	Ajuga reptans	6" h Creeping	Adapted
Coral Honeysuckle	Lonicera sempervirens	Vine	Native
Crossvine	Bignonia capreolata	Vine	Native
Frog Fruit	Phyla nodiflora	12" h Spreading	Native
Horseherb	Calyptocarpus vialis	10" h 36" w	Native
Liriope	Liriope muscari	15" h 12" w	Adapted
Pigeonberry	Rivina humilis	18" h 24" w	Native
Snake Herb	Acanthaceae Dyschoriste linearis	6" h 18" w	Native
Trumpet Vine	Campsis radicans	Vine	Native
Water Clover	Marsilea macropoda	8" h Creeping	Native
Wooly Stemodia	Stemodia lanata	5" h Creeping	Native
Wood Violet	Viola missouriensis	6" Creeping	Native

Perennials
Common Name	Botanical Name	Size	Remarks
Angel Trumpet	Datura wrightii	3' h 3' w	Native
Autumn Joy Sedum	Sedum ‘Autumn Joy’	2' h 2' w	Adapted
Blackeyed Susan	Rudbeckia hirta	2' h 2' w	Native (Seed)
Blackfoot Daisy	Melampodium leucanthum	12" h 12" w	Native
Blazing Stars	Liatris mucronata	2' h 2' w	Native
Brown-eyed Susan	Rudbeckia triloba	3' h 2' w	Native
Clasping Coneflower	Dracopis amplexicalis	2' h 1' w	Native (Seed)
Chocolate Flower	Berlandiera lyrata	1' h 2' w	Native
Cutleaf Daisy	Engielmannia pinnatifida	3' h 3' w	Native (Seed)
Fournerve Daisy	Hymenoxys scaposa	1' h 1' w	Native
Fall Aster	Aster longifolia	3' h 3' w	Native
Globemallow, Scarlet	Sphaeralcea coccinea	12" h 12" w	Native
Indian Blanket	Gailardia pulchella	12" h 2" w	Native (Seed)
Indian Paint Brush	Castilleja indivisa	12" h 2" w	Native (Seed)
Green-headed Cornflower	Rudbeckia lanciniata	4' h 2' w	Native (Seed)
Gregg Dalea	Dalea greggii	1' h 4' w	Native
Gregg’s Mistflower	Eupatorium greggii	2' h 1' w	Native
Illinois Bundleflower	Desmanthus inllinoensis	2' h 1' w	Native (Seed)
Maximilian Sunflower	Helianthus maximilliani	5' h 3' w	Native (Seed)
Mexican Hat	Ratibida columnifera	2' h 1' w	Native (Seed)
Lindheimer’s Senna	Senna lindheimeriana	3' h 3' w	Native
Obedient Plant	Physostegia virginiana	4' h 2' w	Native (Seed)
Pink Evening Primrose	Oenothera speciosa	1' h 1' w	Native (Seed)
Pink Scullcap	Scutellaria suffrutescens	1' h 1' w	Native
Plains Coreopsis	Coreopsis tinctoria	1' h 1' w	Native (Seed)
Purple Coneflower	Echinacea purpurea	2' h 2' w	Native (Seed)
Prairie Verbena	Verbena bipinnitfida	6" h 18" w	Native
Rockrose, Brazilian	Parvonia brazilliensis	3' h 3' w	Adapted
Rockrose	Parvonia lasiopetala	3' h 3' w	Native
Sage, Autumn	Salvia Greggii	3' h 2' w	Native
Sage, Big Red	Salvia penstemonoides	4' h 3' w	Native (Seed)
Sage, Indigo Spires	Salvia longespicata x farinacea	4' h 6' w	Native
Sage, Mealy Blue	Salvia farinacea	2' h 1' w	Native
Sage, Pitcher	Salvia	4' h 3' w	Native (Seed)
Sage, Russian	Perovskia atriplicifolia	4' h 3' w	Adapted
Sage, Scarlet	Salvia coccinea	3' h 3' w	Native (Seed)
Skeletonleaf Goldeneye	Viguiera stenoloba	2' h 2' w	Native
Sundrops	Calylophus drummondianus	6" h 12" w	Native
Texas Betony	Stachys coccinea	18" h 24" w	Native
Texas Greeneyes	Berlandiera texana	4' h 2' w	Native
Texas Lantana	Lantana horrida	5' h 5' w	Native
Texas Star Hibiscus	Hibiscus coccinea	5' h 3' w	Native
Turk’s Cap	Malvaviscus drummondii	4' h 4' w	Native
Whirling Butterflies	Gaura lindheimeri	3' h 3' w	Native
Winecup	Callirhoe involucrate	1' h 2' w	Native
Zexmenia	Wedelia hispida	2' h Spreading	Native

(Ordinance 480-14 adopted 11/20/14; Ordinance 494-15, sec. VI, adopted 5/21/15)