Except as otherwise prescribed by this chapter
or other ordinances and regulations of the Town of Griswold, all construction
of streets and related improvements shall be constructed in accordance
with "Standard Specifications for Roads, Bridges and Incidental Construction,
Form 814A, State of Connecticut, Department of Transportation, 1995,
or any revisions thereof, hereafter referred to as the "Standards."
There shall be no abrupt changes of grade. Select
grades shall not exceed 9% or be less than 0.5%, except that the Board
may permit steeper grades for short distances wherein, in its judgment,
existing topographic conditions or the preservation of natural features
indicate that such modification will not result in unsafe conditions.
Where possible, grades shall not be greater than 3% within 50 feet
of an intersection. Streets shall be designated with a cross pitch
or crown of one-quarter-inch-per-foot, distance measured from the
edge of the pavement to the center line of the street.
All street(s) shall contain a minimum right-of-way of 50 feet unless otherwise laid out with prior written approval of the majority of the Commission. The travel path of any street shall have a minimum width of 28 feet. No dead-end street shall be approved unless a turnaround (cul-de-sac) having a paved travel path of a radius of not less than 40 feet and a street right-of-way of a radius of not less than 50 feet shall be constructed therewith. All cul-de-sacs shall be designed and constructed in accordance with the recommended cul-de-sac layout contained in
Appendix C. There shall be no brush, trees, or boulders within six
feet of each side of the roadbed.
The roadbed shall be constructed as follows:
A. Subgrade. All soft and yielding material and other
portions of the subgrade which will not compact readily when rolled
or which contain organic or man-made material shall be removed, and
all loose rock or boulders over five inches in size shall be removed
or broken to a depth of one foot below the subgrade. All holes or
depressions made by the removal of unsuitable material shall be filled
and rolled uniformly with a vibratory roller weighing at least 10
tons. If the surface of an existing road is two feet or less below
the proposed subgrade surface, it shall be scarified for the full
width of the roadbed. All ledge rock and boulders shall be removed
to a depth of 12 inches below grade of the existing road. The allowable
lift placement on fill areas shall be according to the capacity of
the equipment used and soil material being compacted; however, no
fill lifts shall be greater than 18 inches. All fills will be subject
to materials and compaction testing according to the Standards. The
subgrade shall be constructed 28 feet wide, plus 18 inches beyond
the curb face on each side of the street.
B. Subbase. The subbase shall be applied over the subgrade
and shall consist of bank run gravel with no stones larger than four
inches. Where ledge rock is encountered, it shall be excavated to
a depth of 12 inches, and the subbase shall be at least 12 inches
thick. Where ledge rock is not encountered, the subbase shall be a
minimum of eight inches thick. The subbase shall be compacted to no
less than 95% of the dry density as determined by the Standard Proctor
method. If at any stage of construction unusual conditions appear
or exist, such as in a wetland area, the Board shall require additional
measures be taken to produce a firm subbase.
C. Base course. The base course shall be applied over
the subbase and shall consist of processed gravel with no stones larger
than 1 1/2 inches. The base course shall be six inches thick.
The base course shall be compacted to no less than 95% of the dry
density as determined by the Standard Proctor method. Prior to the
placing of pavement, the base course shall be treated with calcium
chloride at a rate of 0.75 gallon per square yard.
D. Wearing surface (paved travelway). The wearing surface
shall be applied over the base course and consist of a minimum of
two inches compacted thickness binder course and a minimum of 1 1/2
inches compacted thickness riding surface, presently identified as
Class 2 bituminous concrete, machine laid, for a total thickness of
3 1/2 inches after compaction. If the riding surface is placed
more than two weeks after the binder course is placed, a tacking coat
shall be applied over the binding course prior to the placement of
the riding surface. The application of bituminous shall be in strict
accordance with the Standards requirements.
E. All the efforts necessary for the compaction of the
subgrade, subbase, the base course and the bituminous asphalt shall
be accomplished with a roller weighing no less than 10 tons.
F. Where Portland cement concrete or granite curbing
is used, the base course and wearing surface shall be constructed
28 feet wide. Where bituminous concrete curbing is used, the base
course and wearing surface shall be constructed 28 feet wide plus
one foot beyond the curb face on each side of the street.
Slopes shall be finished in a neat manner, and
where streets are cut or filled, the side slope shall not be steeper
than one foot vertical to two feet horizontal, unless the permanence
of the slope shall be otherwise provided by the owner or developer
to the satisfaction of the Board. All slopes and portions thereof
shall be appropriately graded, loamed, and seeded so that same shall
be stabilized so as to prevent any erosion.
Monuments shall be set, to the proper grade,
on all street lines at points of curve and at suitable intermediate
points. Monuments shall be of reinforced concrete, not less than three
feet in length, tops not less than five inches square with a brass
or other suitable center point, sides to taper with bases not less
than six inches square. No monument shall be set in place prior to
completion of all required right-of-way grading, and each monument
shall be set with the brass or other suitable center place on the
point of reference. The top of the monuments shall be set even with
the final grade elevation.
Curbing shall be bituminous concrete, Portland
cement concrete, or granite and shall meet size and installation specifications
as illustrated in the Appendix to this chapter. All curbing shall be properly graded and back filled.
All utilities shall be in place before final
grading, compacting, and surfacing of streets, and when said utilities
are constructed underground, they shall be required to be contained
within appropriate "sleeve piping," excluding water mains, sewerage
mains, and drainage mains. Said underground construction of utilities
shall be done under the supervision and to the satisfaction of the
Board.
Guardrail posts and railing shall be installed
where there is an elevation drop of four feet or more between the
edge of the road and the shoulders and as may be directed by the Board.
New streets shall be named by the owner or developer,
subject to the approval of the Board. Street signs shall be prepared
and installed by the Town of Griswold, the costs of which shall be
borne by the owner or developer.
Four-way intersections shall have two signs,
located diagonally opposite corners. T- intersections shall have one
sign. Each sign post shall identify both intersecting streets.