[Amended 9-26-2005; at
time of adoption of Code (see Ch. 1, General Provisions, Art. II)]
No person shall install or allow to be installed any solid-fuel-burning
appliance, gas-fired equipment, or fuel storage tanks, including but
not necessarily limited to wood, coal, or gas burning stoves, ranges,
cookstoves, furnaces, water heating units, freestanding fireplaces,
combination wood and coal and oil-fired furnaces, or air conditioners
without first receiving a permit for such installation from the Fire
& Rescue Department. Such application for the permit shall describe
the installation to be made, the premises upon which it is to be made,
the name of the person making such installation, whether or not such
installer is licensed by the Maine Fuel Board, or is a Maine-licensed
gas installer, whichever is applicable. Such certification shall be
in writing, signed by the owner of the premises upon which such equipment
or tank is to be installed or by the person who shall make such installation.
[Amended 7-6-1982; 3-3-1986; 1-22-1991; 9-26-2005]
Application for permits, as required in §
162-25, shall be made on forms provided by the Fire & Rescue Department and shall be signed by the owner of the property or his authorized agent and shall be accompanied by the fee set forth in Chapter
A400, Master Fee Schedule. The permit shall be deemed to have been abandoned if the proposed work is not commenced within six months of the date of approval and thereafter diligently pursued to completion.
[Amended 2-24-1997; 9-26-2005]
Upon completion of such installation the applicant shall notify
the Fire Prevention Bureau, which shall cause the installation to
be inspected to assure compliance with all state and local statutes,
ordinances and/or regulations. An inspector shall issue a permit as
soon as practicable. No vented gas-burning appliance, solid or oil-burning
equipment or fuel storage tanks shall be operated for more than four
days unless the installation has been inspected and approved in accordance
with this section and a certificate of compliance executed by the
Fire Prevention Bureau.
[Added 2-24-1997; amended 9-26-2005]
The provisions of this article also shall apply to unvented
appliances that are used primarily for space heating. (See NFPA 54
- unvented equipment.)
[Added 9-26-2005]
No certificate shall be required for the maintenance or use
of any oil-burning equipment or fuel storage tanks where such equipment
or tank was installed prior to June 28, 1965. All such equipment and
tanks shall conform to the standards set out in this article.
[Added 9-26-2005; at
time of adoption of Code (see Ch. 1, General Provisions, Art. II)]
No oil-burning equipment, vented gas-burning appliance or fuel
storage tank to be used in connection therewith shall be installed,
maintained, altered or used in the City unless it shall conform to
the standards established by the Maine Fuel Board pursuant to the
provisions of the state statutes and to the standards herein prescribed,
whichever shall be higher. The name of such installer shall be contained
in the permit application required by this article.
[Added 9-26-2005]
After oil-burning equipment or fuel storage tanks have been
installed, and within 48 hours after notice thereof from the applicant
for the certificate, the Chief of the Department or a Fire Inspector
shall inspect the same and the Chief of the Department shall issue
such certificate upon being satisfied that such equipment and tank
and the installation thereof complies with the requirements of this
article.
[Added 9-26-2005]
No person shall use any oil burning equipment or fuel storage
tanks used in connection therewith, or maintain the same for more
than four days after the installation of the same shall have been
completed, unless a certificate for such equipment or tank shall be
in effect.
[Added 9-26-2005]
No person shall use oil in any oil burning equipment in the
City unless its flash point is not less than 100° F., closed-cup
test.
[Added 9-26-2005]
The thermal fire valve stems on oil-burning equipment must be
in a vertical position.
[Added 9-26-2005]
The firomatic thermal switch on oil-burning equipment shall
not exceed a maximum of four feet about the blast tube of the burner.
[Added 9-26-2005]
All control circuits for oil burners and oil-burner auxiliary
equipment shall be 120 volts maximum with one grounded conductor.