[Ord. No. 977 § 1]
In passing on the adequacy of development plans, the Planning Board or Zoning Board shall apply the standards contained in this article. Each plan shall conform to design standards that will encourage good development patterns within the Borough. The plan shall conform to the proposals and conditions shown on the Official Map and on the Master Plan. The streets, drainage, rights-of-way, school sites, public parks and playgrounds shown on an officially adopted master plan or official map, shall be considered in approval of site plans and subdivision plats.
No subdivision or site plan shall be approved by the Planning Board or Zoning Board unless the plan, development, or use meets the performance standards herein set forth and such State or Federal standards as may be more stringent than those set forth herein. Failure to comply with the performance standards at any time after the issuance of a certificate of occupancy shall be cause for revocation of such certificate. In reviewing any plan, the Planning Board or Zoning Board shall consider:
A. 
Circulation and Parking. The pedestrian and vehicular traffic movement within and adjacent to the site with particular emphasis on the provision and layout of parking areas, off-street loading and unloading, movement of people, goods and vehicles from access roads, within the site, between buildings and vehicles shall be reviewed.
B. 
Site Design and Building Layout. The site design and layout of buildings and parking areas shall be reviewed so as to provide an aesthetically pleasing design and efficient arrangement. Particular attention shall be given to safety and fire protection, impact on surrounding development and contiguous and adjacent buildings and lands.
C. 
Lighting. Adequate lighting shall be provided to ensure safe movement of persons and vehicles and for security purposes. Directional lights shall be arranged so as to minimize glare and reflection on adjacent properties.
D. 
Buffering. Buffering shall be located around the perimeter of the site to minimize headlights of vehicles, noise, light from structures, the movement of people and vehicles, and to shield activities from adjacent properties when necessary. Buffering can consist of fencing, landscaped berms, evergreens, shrubs, bushes, deciduous trees or combinations thereof to achieve the stated objectives.
E. 
Landscaping. Landscaping shall be provided as part of the overall site plan design and integrated into building arrangements, topography, parking and buffering requirements. Landscaping shall include preservation of existing vegetation to the extent possible as well as trees, bushes, shrubs, ground cover, perennials, annuals, plants, sculpture, art and the use of building and paving materials in an imaginative manner.
F. 
Common Open Space. Common open space shall be provided as part of any planned development. Open space should be classified as developed (recreational) or undeveloped (natural) space. Undeveloped open space should have as a prime objective the preservation of a site's natural amenities (e.g. beaches, water body features, dunes, etc.).
G. 
Signs. Signs shall be designed so as to be aesthetically pleasing, harmonious with other signs and buildings on the site. They shall be located so as to achieve their purpose without constituting hazards to vehicles and pedestrians or be visually distracting form the overall site design.
H. 
Utilities. Storm drainage, sanitary waste disposal, water supply and solid waste collection and disposal shall be reviewed. Particular emphasis shall be given to the preservation of stream corridors, establishment of drainage rights-of-way and the adequacy of existing utility systems, and the need for improvements both on-site and off-tract, where appropriate, to adequately carry run-off and sewage, and to maintain an adequate supply of water at sufficient pressure.
I. 
Environmental Considerations. Environmental elements relating to prevention of soil erosion, preservation of trees, protection of watercourses, wetlands and floodplains, protection of water sources, noise, air quality, topography, soil and animal life shall be reviewed and the design of the plan shall minimize any adverse impact on these elements.
J. 
Street Furniture. The site plan shall provide for those elements of street furniture appropriate to the particular use. These may include phone booths, benches, bike racks, trash receptacles and bus shelters.
K. 
Conformance with Master Plan or Official Map. If the Master Plan or the Official Map provides for the reservation of designated streets, public drainageways, flood control basins, or public areas such as parks, school sites, historic sites or similar lands within the proposed development, such areas shall be shown on the plan in locations and sizes suitable to their intended uses. The Planning Board may reserve the locations and extent of such public areas in accordance with the requirements of N.J.S.A. 40:55D-44.
L. 
Minimum Roof Pitch. A minimum roof pitch of 5 on 12 is required for all single and two-family residential structures.
A. 
Landscape transition areas or buffers shall be provided along any lot and street line of any nonresidential lot where such line or the center line of the adjacent street coincides with a residence zone boundary. Yard requirements may be deemed to be included as part of the landscape transition buffer.
The Planning Board may waive the landscape transition area requirement where existing natural or man-made physical barriers provide an effective visual separation between residential and nonresidential uses.
Each permitted use shall provide suitable buffers in order to protect the character, and to minimize any adverse impacts or nuisances on adjoining properties. Buffers shall be located around the perimeter of the site to minimize glare from headlights of vehicles, to minimize noise, to shield light from structures, to shield the movement of people and vehicles from adjacent property and to shield activities from adjacent properties. Buffers are fences, walls, landscaping, berms and mounds used to minimize any adverse impacts or nuisances on the site from adjacent areas. The applicant shall incorporate into its landscaping plan submitted with the site plan a buffer design plan which shall incorporate the following principles:
1. 
Buffers shall be located along property lines shielding various uses and activities from each other to be consistent with § 85-82.
2. 
Buffer areas shall consist of lawn areas and massed evergreen and deciduous trees and shrubs planted in a manner that will provide a continuous visual screen throughout the entire year.
3. 
Evergreen and deciduous shrubs shall have a minimum height of three feet when planted and shall be of varieties suggested herein.
4. 
The height of shrubs planted in a buffer area shall be measured from the ground level around the base of shrub to the topmost part of the shrub, once the shrub has been properly planted in the ground.
5. 
Where an area required for a buffer is already landscaped, it shall be left in its natural state, and existing growth shall be supplemented with additional plant material where necessary to bring the buffer area up to the minimum requirements of this section.
6. 
In nonresidential zones, all parking areas, garbage collection areas and loading/unloading areas exclusive of ingress and egress drive shall be screened from adjacent properties by a buffer strip at least five feet in width.
The plant materials, fences, or walls used for screening purposes shall be sufficient to screen an area at all seasons of the year from the view of persons standing at an elevation approximately equal to that of the area to be screened on adjacent streets or properties.
Any article or material stored outside an enclosed building as an incidental part of the primary operation on a lot shall be screened as provided hereinafter by fencing, walls or evergreen planting.
Where the Planning Board deems it necessary to assure an effective visual screen between nonresidential uses and streets or residentially zoned properties, such Board may require, in addition to landscaping, the provision of a fence of a type, height, and design suitable for the purpose, provided that the height of such fence or screening shall not exceed six feet.
B. 
Landscaping Plan. Every application for approval of a site plan or a subdivision shall contain a landscaping plan prepared by a New Jersey certified landscape architect, registered architect or professional engineer. The plan shall identify, locate and provide planting details for all proposed trees, shrubs, bushes, plant material and ground cover, all such existing plant materials proposed to be retained, and all ground cover, and natural features. For all existing natural growth proposed to be retained the plan shall state the method(s) proposed to be used for its protection during and after construction (e.g. fencing, tree wells, curbing or similar devices).
The landscaping plan shall conform with the following design requirements, as applicable:
1. 
The site plan or subdivision plan shall be so designed as to preserve, wherever possible, natural features such as large trees, views, and scenic features or other recognized community assets. Efforts shall be made to utilize as much existing vegetation on the site as possible.
2. 
All nonpaved areas on properties shall be appropriately landscaped with trees and shrubs, grass and other suitable landscaping materials.
3. 
Landscaping shall be provided in public areas, recreation sites and adjacent to buildings. Where possible, shade trees shall be planted on the south side of buildings to shield them from the summer sun and evergreens on the north side of buildings, to serve as windbreaks.
4. 
The landscaping plan shall provide for a variety and mixture of plant materials taking into consideration their susceptibility to disease, colors (by season), textures, shapes, blossoms, and foliage.
5. 
The choice of landscaping shall be appropriate to site soil conditions and availability of water for irrigation.
6. 
Street trees shall be planted at a minimum interval of 40 feet on-center and they shall have a minimum caliper of 3 1/2 inches measured at six inches from the ground. Street trees can help unify dissimilar building styles and uses, separate vehicle and pedestrian zones, and provide shade, overhead canopy and scale to the streetscape. Flowering trees shall not be used as street trees.
7. 
Existing large trees shall be saved by not changing the surface elevation around the trees by more than 12 inches, construction of tree wells, and by erecting four foot high snow fence located at the drip-line of trees prior to any site disturbance.
8. 
Any tree on the site having a trunk diameter of more than four inches at a height of two feet from the ground shall not be removed or relocated unless it is in accordance with a plan approved by the Planning Board.
9. 
A sufficient number of shade trees shall be provided and planted on the site to maximize shading and insure a desirable living environment. Except as set forth hereinafter, at planting, deciduous trees shall have a minimum caliper of 2 1/2 inches measured at six inches above ground level, and evergreen trees shall be at least six feet high. All trees shall be balled and burlapped.
10. 
Shrubs used as screens in buffer areas shall have an initial height of not less than five feet and planted at intervals appropriate for the activities involved.
11. 
All new plant materials shall be guaranteed for two years to be in healthy and vigorous condition and replaced as deemed necessary by the Planning Board.
12. 
Any damaged or dead trees shall be replaced by the developer and/or applicant up to two years after a final certificate of occupancy has been issued.
13. 
Landscaping shall be located to provide for climate control. For example, shade trees on the south to shield the hot summer sun and evergreens on the north for windbreaks.
14. 
Use landscaping to accent and complement buildings. For example, groupings of tall trees to break up long, low buildings and lower plantings for taller buildings.
15. 
Shade trees shall be planted on each side of every street so as not to interfere with utilities, sidewalks and proper sight distance at intersections.
16. 
Replacement trees shall conform to the type of existing trees in a given area.
17. 
Landscaping shall be provided in public areas, recreation sites and adjacent to buildings.
18. 
Provide for a variety and mixture of landscaping. The variety shall consider susceptibility to disease, colors, season, textures, shapes, blossoms and foliage.
19. 
Consider the impact of any proposed landscaping plan at various time intervals so that, for example, shrubs do not grow and eventually block sight distances.
20. 
Landscaping shall be located in protected areas, along walkways, center islands and at the end of parking bays. In narrow islands, low spreading plants such as creeping juniper, English ivy, myrtle or pachysandra are appropriate.
21. 
All landscaping in parking areas shall be carefully located so as not to obstruct vision. A variety of different types of trees shall be grouped to break up the mass of cars. Tree types shall be selected from those specified in "Trees for New Jersey Streets. 2nd Revision, 1974," published by N.J. Federation of Shade Tree Commission. Trees that cause damage or excessive site maintenance problems due to root systems or leaf shedding shall be avoided. Trees that can withstand parking area conditions are encouraged.
22. 
Those portions of all front, side and rear yards not used for off-street parking, or vehicular or pedestrian circulation, shall be planted with trees, shrubs, plants or grass lawns or combinations thereof.
23. 
An in-ground or drip hose irrigation system shall be used to water landscaping as determined to be necessary by the Planning Board.
C. 
Landscaping shall be provided as part of the overall site plan design and integrated into building arrangements, topography, parking and buffering requirements. Landscaping shall include preservation of existing vegetation to the extent possible as well as trees, bushes, shrubs, ground cover, perennials, annuals, plants, sculpture, art and the use of building and paving materials in an imaginative manner.
The following landscape materials shall be used in the development of landscape plans. This list of species is to be used as a guideline and is not meant to exclude other acceptable species.
Common Name
Minimum Size
Shade Trees
Acer pseudoplatanus
Planetree Maple
2 2 1/2" cal
12-14' ht
Acer rubruym
October Glory
2 2 1/2" cal
Red Maple
12-14' ht
Celtis occidentalis
Common Hackberry
2-2 1/2" cal
12-14' ht
Quercus phellos
Willow Oak
2-2 1/2" cal
12-14' ht
Platanus acerfolia "Bloodgood"
London Planetree
2-2 1/2" cal
12-14' ht
Flowering Trees
Cornus Kousa
Kousa Dogwood
6-8' ht
Magnolia virginiana
Sweetbay Magnolia
6-8' ht
Amelanchier Canadensis
Shadblow Serviceberry
6-8' ht
Viburnum prunifolium
Blackhaw Viburnum
2-2 1/2" cal
8-9' ht
Malus floribunda
Japanese Crabapple
8-9' ht
Prunus yedoensis
Yoshino Cherry
2-2 1/2" cal
Evergreen Trees
Ilex opaca
American Holly
7-8' ht
Pinus strobes
White Pine
7-8' ht
Pinus thunbergii
Japanese Black Pine
7-8' ht
Juniperus virginiana
Eastern Red Cedar
7-8' ht
Thuja occidentalis
Dark American
7-8' ht
"Nigra"
Arborvitae
Shrubs
Ilex glabra
Inkberry
18-24" ht, 3' o.c.
Myrica pensylvanica
Bayberry
18-24" ht, 3' o.c.
Prunus maritima
Beach Plum
18-24" ht, 3' o.c.
Viburnum dentatum
Arrowwood Viburnum
18-24" ht, 3' o.c.
Pyracantha coccinea
Rutgers Firethorn
18-24" ht, 3' o.c.
Rosa rugosa
Rugosa Rose
18-24" ht, 3' o.c.
Rosa virginiana
Virginia Rose
18-24" ht, 3' o.c.
Vaccinium corymbosum
Highbush Blueberry
18-24" ht, 3' o.c.
Ilex crenada
Japanese Holly
18-24" ht, 3' o.c.
Berberis gladwynensis
William Penn Barbery
18-24" ht, 3' o.c.
Ground Cover
Cotoneaster dammeri
Bearberry Cotoneaster
12-15" ht, 2' o.c.
Juniperus chinensis
Sargent Juniper sargenti
12-15" ht, 2' o.c.
Rosa wichuraina
Memorial Rose
12-15" ht, 2' o.c.
Juniperus conferta
Shore Juniper
12-15" ht, 2' o.c.
NOTE: All trees and shrubs shall be balled and burlapped.
[Ord. No. 812 § 2; Ord. No. 983 § 6; Ord. No. 1013 § 1; Ord. No. 1062 § 5; Ord. No. 1287-2018 § 13]
A. 
In all zones, at the time any building or structure is erected, enlarged, or increased in capacity, there shall be provided off-street parking for automotive, bicycle and other vehicles and off-street loading facilities in accordance with the requirements set forth herein as well as the parking space requirements for the handicapped contained in P.L. 1975, Chapter 221; N.J.S.A. 52:32-11 and by law. All required parking and loading facilities shall be paved with an all weather impervious surface and shall be completed prior to the issuance of a certificate of occupancy. The construction, alteration, or enlargement of any public or private parking or loading area or of accesses to such area shall require site plan approval by the Planning Board.
B. 
Each permitted use shall provide an area for the orderly deposit and pickup of refuse which is concealed from adjacent residential properties. This area shall be visually screened by a decorative wall or fence and landscaping. The overall design shall be in architectural harmony with the principal building and shall not be located within buffer areas.
C. 
All provisions and facilities for storage, other than the pickup of refuse, shall be contained within a principal building.
D. 
Minimum Parking Requirements.
The following minimum number of parking spaces shall be provided for the uses specified per gross floor area unless otherwise indicated:
Land or Building Use
Minimum Standards
Assembly hall, auditorium, theater, church or other similar place of public assemblage.
[Ord. No. 1287-2018 § 13]
1 space for each 4 fixed seats. 1 seat shall be considered 22 inches in calculating the capacity of pews or benches.
Automobile and gasoline service station
[Ord. No. 1287-2018 § 13]
1 space per tow truck, grease rack, or similar unit of service capability, with a minimum of 5 spaces, plus 1 space for each 2 employees during the period of greatest employment, provided that the total number of spaces shall be not less than 6, but no greater than 12 spaces.
Banks and other financial institutions
[Ord. No. 1287-2018 § 13]
1 space for each 600 square feet of gross floor area. Additionally, drive-in banks shall provide room for at least 3 automobiles per drive-in window and/or lane for queuing purposes.
Beauty and barber shops
[Ord. No. 1287-2018 § 13]
1 space for each 400 square feet of gross floor area.
Business, professional offices
[Ord. No. 1287-2018 § 13]
1 space for each 400 square feet of gross floor area.
Sightseeing and sport fishing boats
[Ord. No. 1287-2018 § 13]
1 space for 4 passengers as determined by the appropriate Borough license and recorded seating capacity.
Dwelling: Detached single family unit
[Ord. No. 1287-2018 § 13]
In accordance with the standards established by the New Jersey Residential Site Improvement Standards (RSIS) N.J.A.C. 5:21-1 et seq.). Stacked parking may contribute toward meeting the minimum requirement as long as parked vehicles do not encroach upon public property. If there is a garage, there must be 20 feet from the property line to the garage door.
[Ord. No. 1030 § 6; amended 1-25-2023 by Ord. No. 1392]
Dwelling: Attached single family e.g. two-family unit, townhouse, duplex, three-family unit, or triplex
[Ord. No. 1287-2018 § 13]
In accordance with the standards established by the New Jersey Residential Site Improvement Standards (RSIS) (N.J.A.C. 5:21-1 et seq.). Stacked parking within an enclosed garage where vehicles must exit the site by backing out into the street is not permitted. A car may be stacked in front of the garage if there is 20 feet from the garage to the property line. If there is a garage, there must be 20 feet from the property line to the garage door.
[Ord. No. 916 § 1; Ord. No. 988 § 1; amended 1-25-2023 by Ord. No. 1392]
Dwelling: Multi-family or garden apartment with more than three units per structure
2 parking spaces per living unit and stacked parking for 2 cars may be permitted according to site plan review. Stacked parking within an enclosed garage where vehicles must exit the site by backing out into the street is not permitted. A car may be stacked in front of the garage if there is 20 feet from the garage to the property line. If there is a garage, there must be 20 feet from the property line to the garage door.
[Ord. No. 916 § 1; Ord. No. 988 § 1]
Fast food or drive-in restaurants
1 space for each 3 seats, plus 1 space for each 40 square feet of gross floor area, excluding the seating area
General office, corporate office, research
1 space for each 400 square feet of gross floor area.
Hotel or motel, including all M-1 Zones and Multi-Family
[Ord. No. 762 § 3; Ord. No. 844 § 1; Ord. No. 983 § 6; Ord. No. 1108 § 3]
1 space for each 400 square feet of gross floor area.
Minimum On-Site Parking:
Hotel/motel
1.2 spaces (up to 650 square feet) - no tandem parking permitted. 2 spaces (from 651-799 square feet) - tandem parking permitted if dedicated to a single unit.
Multi-family:
2 spaces (800-2,000 square feet) - tandem parking permitted if dedicated to a single unit. 3 spaces (over 2,000 square feet) - 1 of 3 spaces may be tandem.
Accessory restaurants/gift shops:
No additional parking is required for restaurants/coffee shops having no more than 60 seats. For restaurants having more than 60 seats, additional parking is required at 1 space for every 6 seats or fraction thereof for all seating above 60 seats. No additional parking is required for gift shops.
Medical or dental clinic or office
1 space for each 100 square feet of gross floor area or 4 spaces for each doctor or dentist, plus 1 space for each employee, whichever is greater.
Personal service business
1 space for each 400 square feet of gross floor area.
Private kindergarten, child nursery or institutional home
1 space for each 600 square feet of gross floor area.
Public or private schools
1 space for each employee, plus 1 space for each 5 seats in the auditorium or other places of assembly available to the public.
Restaurant, similar establishment outside the M-1 zone
1 space for each 6 seating accommodations or 1 space for each 60 square feet of floor area devoted to patron drinking and dining use, or 1 space for every 200 square feet of building floor area, whichever yields the greatest number of spaces plus 1 space for every 500 square feet of total square feet (including kitchen and storage areas) dedicated for employee parking.
[Ord. No. 762 § 2]
Recreation centers, clubs and service organizations
1 space for each 500 square feet of gross floor area plus 1 space for each 2 full-time employees.
Retail business and stores
1 space for each 400 square feet of gross floor area.
Self-service laundry
1 space for each 400 square feet of gross floor area.
Supermarkets
1 space for each 400 square feet of gross floor area.
Undertakers, mortuary or funeral home
1 space for each 60 square feet of floor area available for seating accommodations plus 1 space for each person employed therein.
Mixed uses
If 2 or more uses are conducted on 1 lot, the minimum required number of parking spaces shall be the aggregate required minimum number of parking spaces for each use, computed separately.
Uses not specified
As determined by the Planning Board on the basis of the number of persons to be employed or to reside in or visit said building and the anticipated use by residents, visitors, or patrons of transportation modes other than private automobiles.
E. 
Bicycle or Moped Parking Requirements. In addition to the required facilities for passenger automobiles, facilities for the secure and convenient parking of bicycles shall be required.
F. 
Off-Street Loading Requirements. Off-street loading area or berths, open or enclosed with proper access from a street, highway, common service driveway or alley shall be required.
G. 
Supplementary Parking, Storage and Loading Space Requirements. In addition to other provisions of this article, the following shall apply:
1. 
Fractional Space: When the application of a unit of measurement for parking space or loading space to a particular use or structure results in a fractional space, a space shall be required for each such fraction.
2. 
Computing Number of Employees: The number of employees, where not clearly stipulated, shall be computed on the basis of persons to be employed, taking into consideration day, night and seasonal variations.
3. 
In determining minimum parking space requirements focuses not covered in this article, the Planning Board shall be guided by the number of persons to be employed in said building or by the use; the number of persons expected to reside in, visit, or patronize the building or use; the anticipated percentage of residents, visitors or patrons using various transportation modes; and the need for safe and convenient loading space for visitors or patrons and goods.
4. 
Trash storage containers shall be provided for all motels at a ratio of one standard container capable of holding 40 to 50 cubic feet for each 40 units. A coffee shop shall be considered five units.
5. 
Each permitted use shall provide an area for the orderly deposit and pickup of refuse which cannot be seen from adjoining public streets, customer parking areas or adjacent lots when viewed by a person standing on ground level. This area shall be visually screened by a decorative wall or fence and landscaping. The overall design shall be in architectural harmony with the principal building and shall not be located within buffer areas.
6. 
Solid waste collection areas shall be provided and shall be located for the convenience of the occupants. Exterior and interior refuse receptacles, aesthetically designed, shall be provided for shopper convenience.
7. 
All provisions and facilities for storage, other than pickup of refuse, shall be contained within a principal building. Any article or material stored outside an enclosed building or an incidental part of the preliminary operation on a lot shall be located in the side or rear yard and be so screened by fencing, walls, evergreen planting or combinations thereof that it cannot be seen from adjoining public streets or adjacent lots when viewed by a person standing on ground level.
8. 
All fences, trees, plantings, shrubbery, or other screening required by the Planning Board shall be consistently maintained at the level of quality required of said items at the time they were initially installed.
H. 
Parking and Off-Street Loading and Unloading Requirements.
1. 
Where it can be demonstrated, at the time of Planning Board review, that the parking and/or loading and unloading requirements of this article will result in more parking spaces than actual needs require, the Planning Board may permit a portion of the proposed parking and/or loading areas to remain unpaved, but landscaped. Such unpaved area shall remain reserved for such future facilities needs, and if conditions in use or actual operation of the proposed use vary, the Planning Board may require such unpaved space to be paved.
2. 
Minimum off-street parking loading requirements as required by this article may only be exceeded, where it can be demonstrated, at the time of Planning Board review, that such additional parking facilities are necessary for the actual operation of a proposed use. In such instances, the Planning Board may grant an increase in minimum spaces on a lot, provided that all other bulk and area requirements are met for the use in the district in which it is located.
3. 
A variance and public notice shall be required when the proper number of parking spaces are not being provided on a lot.
I. 
Use Change Affecting Parking Needs. Whenever after the date of this Ordinance there is a change in the number of employees or business visitors or in the lawful use of the premises or in any other unit of measurement specified herein and whenever such change creates a need for an increase in more than 20% of the number of off-street automobile parking spaces as determined by the requirements of this Ordinance, additional off-street parking facilities shall be provided within a reasonable time on the basis of the adjusted needs. The provision of additional parking shall constitute an expansion of use and will in turn require site plan review by the Planning Board.
J. 
Recycling Requirements. The intention of this subsection is to provide standards and design guidelines governing the preparation of recycling plans for certain developments requiring subdivision or site plan approval. A recycling plan shall be submitted with every preliminary development plan application for 50 or more units of single-family or two-family housing, multi-family or townhouse dwellings of 25 or more units, and all nonresidential development proposals for the utilization of 1,000 square feet or more of land.
Nonresidential and institutional establishments that are exempt from source separation requirements pursuant to N.J.S.A. 13:1E-99.16 of the Recycling Act shall submit written verification of such exemption in lieu of the recycling plan required herein.
1. 
Standards for Single-Family and Two-Family Dwellings:
a. 
A recycling plan in the form of a narrative description and diagram or maps shall be submitted with every preliminary development proposal for the construction of 50 or more units of single-family or two-family housing.
b. 
The recycling plan shall furnish a list of all applicable recyclable materials, including at a minimum, the following:
(1) 
Acceptable glass containers.
(2) 
Acceptable metal containers.
(3) 
Acceptable plastic containers.
(4) 
Acceptable mixed paper.
(5) 
Tires.
(6) 
White goods.
(7) 
Leaves.
(8) 
Batteries.
c. 
Each single-family and two-family dwelling unit or its associated garage shall be designed to provide a location containing at least 24 cubic feet of space per unit for storage of designated recyclable material. The location shall be clearly marked as such on floor plans of the dwelling unit or garage.
2. 
Standards for Multi-Family and Townhouse Dwellings:
a. 
A plan in the form of a narrative description and diagrams and maps shall be submitted with a preliminary development application for multi-family or townhouse development of 25 or more units. The herein standards may be modified by the Planning Board upon documentation from an applicant indicating actual solid waste surveys from similar projects that would support such modification and ensure the most appropriate space allocation that encourages recycling.
b. 
The recycling plan shall furnish a list of all applicable recyclable materials, including, at a minimum, the following:
(1) 
Acceptable glass containers.
(2) 
Acceptable metal containers.
(3) 
Acceptable plastic containers.
(4) 
Acceptable mixed paper.
(5) 
Tires.
(6) 
White goods.
(7) 
Leaves.
(8) 
Batteries.
c. 
Each multi-family and townhouse dwelling unit shall be designed to provide a location containing at least 18 cubic feet of space per unit for storage of designated recyclable materials. The location shall be clearly marked as such on floor plans of the dwelling unit. The required storage area may be designated within a garage structure accessory to the dwelling unit, if available.
d. 
For every 25 dwelling units or portions thereof, an outdoor storage area containing a concrete pad of sufficient dimension to handle the following projected minimum recyclable material generation rates shall be provided.
Minimum Generation Rates:
Newspaper
10 lbs. per person per month
Glass
7 lbs. per person per month
Aluminum
0.4 lbs. per person per month
Tin cans
6 lbs. per person per month
Plastic containers
0.8 lbs. per person per month
An explanation of the method used to determine the proposed size of a storage area shall be provided. An explanation shall also be provided concerning how the determination was made for the size of storage containers.
The outdoor storage area shall be conveniently located for residential disposition of recyclables, preferably near, but clearly separated from a trash refuse dumpster. The outdoor area shall be enclosed on three sides by a solid fence of six feet height and landscaping shall be provided around the fence in accordance with landscape standards contained in this Ordinance.
Outside deposit areas shall not be permitted in any required yard or setback area nor shall they interfere with the adequate operation of off-street parking facilities.
3. 
Standards for Nonresidential Development:
a. 
All preliminary nonresidential development proposals for the utilization of 1,000 square feet or more of land shall submit with a preliminary site or subdivision plan a recycling plan to the Borough and to the Cape May County Municipal Utilities Authority that includes the following information:
(1) 
Description of the type of business expected to occupy the building. In a case where, during site plan or subdivision review, the business type is unknown, a recycling plan shall be based on an assumed tenancy mix. Should there be substantial deviation by more than 25% from the assumed tenancy mix prior to issuance of a certificate of occupancy, a revised recycling plan shall be submitted to the Borough's Construction Official and/or Recycling Coordinator prior to issuance of the final certificate of occupancy.
(2) 
Nonresidential establishments shall furnish a list of all applicable recyclable materials, including, at a minimum, the following:
(a) 
Paper, including acceptable mixed paper, corrugated cardboard, and office paper.
(b) 
Acceptable glass containers.
(c) 
Acceptable metal containers.
(d) 
Tires.
(e) 
Used motor oil.
(f) 
White goods.
(g) 
Batteries.
(h) 
Food wastes.
(i) 
Organic material.
(3) 
Approximate amount of each recyclable material, listed by type, expected to be generated (in cubic yards or tons, monthly, or annually.)
(4) 
Material separation and handling practices, which shall include the following:
(a) 
A list of areas where material is expected to be generated.
(b) 
A method of storing material at the point of its generation.
(c) 
A method of moving material from the generation area to the storage area.
(d) 
Location of designated storage area.
(e) 
Size of storage area with an explanation of method used to determine size of storage area.
(f) 
Size and type of container used to store each material, both at the point of generation and storage prior to hauler pickup. An explanation shall be provided concerning how determination was made for the sizing of storage containers.
(g) 
The method of visually screening the recycling area.
(h) 
Method of material removal, including frequency of pickup and type of vehicle(s) expected to be used for pickup.
(i) 
Safeguards to minimize confusion between recycling areas and refuse collection areas shall be outlined.
4. 
Any agreement with a solid waste hauler or within a separate entity for recycling of source separated designated materials shall also be submitted for review.
5. 
On-site storage space requirements for designated recyclable materials shall be sufficient to accommodate the volume of recyclable materials expected to be generated by the proposed development. On-site collection areas shall not be permitted in any required yard or setback area, nor shall they interfere with the adequate operation of off-street parking facilities.
6. 
Landscaping and screening of the recycling storage area shall be provided in accordance with landscape standards contained elsewhere in this Ordinance.
7. 
Compliance with Other Municipal Codes.
Storage areas, both indoors and outdoors, shall meet all fire, building, health codes, and other applicable requirements of the Borough of Wildwood Crest.
8. 
Recycling Collection and Education Plan.
For both residential and nonresidential developments required to submit a solid waste recycling program, a plain language summary of the proposed recycling requirement storage areas and collection process shall be prepared. Such summary material shall be included as part of any sales or rental transactions, and the method for such information dissemination shall be provided as part of a development application.
If a residential or nonresidential development application contains a homeowners association or business owners association, then the bylaws for such associations shall address the recycling plan envisions for the development project.
[Ord. No. 812 § 3–4; Ord. No. 834 § 1;Ord. No. 908 § 2;Ord. No. 1017 § 11;Ord. No. 1074 § 1]
A. 
Access. Unobstructed access to and from a street shall be provided. Paved access drives or driveways shall be provided in accordance with the criteria provided in this article.
B. 
Location of Parking Spaces. Such parking spaces, open or enclosed, shall be on the same lot or tract of land as the building or use to be served unless the Planning Board, in connection with site plan review, shall approve collective off-street parking facilities for two or more buildings or uses on adjacent or contiguous lots. The total of such collective off-street parking facilities shall be not less than the sum of facilities required for the individual uses computed separately.
1. 
Loading and unloading areas shall be prohibited in the area between the front building line and the street line on arterial roads.
2. 
In residential zones, a driveway within a required front yard may be used and counted as one motor vehicle parking space, provided a parked vehicle does not encroach upon public property.
3. 
In commercial zones, parking spaces which require vehicles to back out directly onto any "main" or north/south streets are prohibited. However, backing out is permitted on side streets.
4. 
Every attached dwelling unit type shall have a minimum setback of 10 feet from any common or shared parking area(s) containing five or more vehicle parking spaces.
C. 
Location in Different Zones. No access drive, driveway or other means of ingress and egress shall be located in any residential zone to provide access to uses other than those permitted in such residential zone.
D. 
Sidewalks and Curbing. Sidewalks between parking areas and principal structures, along aisles and driveways and wherever pedestrian traffic shall occur, shall be provided with a minimum width of five feet of passable area and be raised six inches or more above the parking area except when crossing streets or driveways. At points of intersection between pedestrian and motorized lines of travel, and at other points where necessary to avoid abrupt changes in grade, a sidewalk shall slope gradually so as to provide an uninterrupted line of travel. Guardrails and wheel stops permanently anchored to the ground shall be provided in appropriate locations. Parked vehicles shall not overhang or extend over sidewalk areas.
E. 
Curb Cuts in All Districts. Curb cuts in all districts shall be limited in order to provide for on-street parking. Curb cuts for single-family and duplexes shall be limited as specified under § 85-74D6. For all other developments, curb cuts shall be limited to the size needed to access the development as approved by the Planning Board during site plan review. However, in all districts, at least 50% of the lot frontage shall be raised curb, with a minimum of 35% being continuous raised curb. The area in front of the raised curb to the building shall be landscaped.
F. 
Access to Off-Street Parking. In the M-1 Zone circulation patterns shall be designed to minimize curb cuts and be designed to lessen traffic impacts flowing on the North and South Avenues.
G. 
Landscaping.
1. 
Parking areas shall be suitably landscaped to minimize noise, glare and other nuisance characteristics as well as to enhance the environment and ecology of the site and surrounding area. General landscaping design shall conform to criteria set forth in this article. All open parking areas and access-ways thereto shall be properly drained and all such areas shall be a paved surface.
2. 
Parking viewed from the public right-of-way or from any property used for residential purposes shall be suitably shielded.
3. 
All commercial off-street parking areas shall be bordered by landscaped areas containing trees and shrubs to shield automobiles from view. Whenever feasible, the Planning Board shall require that at least 10% of the total parking lot area be used for interior landscaping. Such interior landscaping shall be distributed throughout the parking lot in planting islands to provide maximum shade and buffer from noise and glare. At least one deciduous tree for every 10 parking spaces shall be required within the parking lot. For the purposes of this requirement, any parking area enclosed or covered shall not be calculated as part of the total parking area.
4. 
In all residential off-street parking areas interior landscaping shall be distributed throughout as determined by the Planning Board to provide for maximum shade and buffer from noise and glare. Buffering of fencing, evergreens, shrubs, bushes, deciduous trees, plants, or combination thereof shall be located along the edge of parking lots or property lines to minimize headlights of vehicles, noise, light from structures, the movement of people and vehicles, and to shield activities from adjacent properties and roadways.
5. 
Landscaping shall be provided as part of the overall site plan design and shall be integrated into building arrangements, topography, parking, and buffering requirements. Landscaping shall include preservation of existing vegetation to the extent possible as well as trees, bushes, shrubs, ground cover, perennials, annuals, plants, sculpture, art, and the use of building and paving materials in an imaginative manner.
H. 
General Circulation Design Principles.
1. 
Parking space allocations should be oriented to specified buildings.
2. 
Parking areas may be designed to focus on major walkways which should be marked.
3. 
Where possible, parking areas shall be separated from streets by islands with a minimum width of six feet.
4. 
All parking areas shall be provided with permanent and durable curbing or bumpers unless this requirements is waived by the Planning Board.
5. 
Where pedestrians must cross service roads or access roads to reach parking areas, crosswalks should be clearly designated by pavement markings and/or signs.
6. 
All parking and loading spaces and driveways should be so arranged that cars and trucks may be turned on the lot so that it is not necessary to back into any street. Vehicles being repaired shall be screened from adjacent properties.
I. 
Driveway Design.
1. 
All entrance and exit driveways shall be located to afford maximum safety to traffic, provide for safe and convenient ingress and egress to and from the site, and to minimize conflict with the flow of traffic.
2. 
Any exit driveway or driveway lane shall be so designed in profile and grading and located to provide the following minimum sight distance of 150 feet measured in each direction. The measurements shall be from the driver's seat of a vehicle standing on that portion of the exit driveway that is immediately outside the edge of the road right-of-way.
3. 
No entrance or exit driveway shall be located on a rotary, ramp of an interchange, or within 20 feet of the beginning of any ramp or other portion of an interchange.
4. 
For all one-, two-, and three-family dwellings with a driveway between a building and property line, there shall be a minimum distance of 10 feet between the building and property line.
J. 
Driveway Angle.
1. 
Two-Way Operation. Driveways used for two-way operation shall intersect the road at an angle to as near 90° as site conditions will permit and in no case will be less than 60°.
2. 
One-Way Operation. Driveways used by vehicles in one direction of travel (right turn only) shall not form an angle smaller than 45° with a road, unless acceleration and deceleration lanes are provided.
K. 
Driveway Dimensions. The dimensions of driveways shall be designed to adequately accommodate the volume and character of vehicles anticipated to be attracted daily onto the land development for which a site plan is prepared. The required minimum dimensions of nonresidential driveways shall be 24 feet.
L. 
New or Altered Parking Lots. No public or private parking area or access roads thereto shall be constructed, altered or added to in the Borough until there shall have been filed with the Planning Board an application for a building permit, which shall include a plan, in duplicate, drawn to scale, showing the actual dimensions of the lot or lots to be built upon, the exact size and location on the lot or lots of the building or structure and accessory buildings already existing or to be erected, and containing such other information as shall be deemed necessary by the Planning Board to determine conformity with the provisions of this ordinance and of the Building Code.
M. 
Maintenance of Off-Street Parking and Loading Areas.
1. 
Every parcel of land hereafter used as a public or private off-street parking or loading area shall be maintained in good condition, free of hazards and deterioration. All pavement areas, sidewalks, curbs, drainage facilities, lighting, bumpers, guardrails, markings, signs, bicycle parking devices, landscaping and other improvements shall be maintained in workable, safe and good condition.
2. 
All off-street parking and loading areas, including driveways, shall be maintained with graded, dust-free surfaces that are well drained, such as asphalt or porous pavement as approved by the Borough Engineer. All such off-street parking and loading space and necessary passageways and driveways giving access thereto shall be maintained in a state of good repair and the surface thereof shall be kept clear or ruts, potholes, protrusions, debris, and other vehicular or pedestrian hazards. One- or two-family dwellings, however, may incorporate parking strips separated by gravel or grass as approved by the Borough Engineer for all off-street parking spaces and/or driveways.
3. 
The Governing Body may authorize repairs for such improvements if, after proper notice, the owner fails to maintain such improvements and such conditions constitute a hazard to health and safety or where such improvements are government by a development or other similar agreement.
N. 
Automobile Parking Design Principles.
1. 
The width of all aisles providing direct access to individual parking stalls shall be in accordance with the requirements set forth below.
The minimum width of access aisles shall conform with the following requirements:
Parking Angle
(degrees)
Aisle Width One-Way Traffic
Aisle Width Two-Way Traffic
0 parallel
12
20
30
12
20
45
14
20
60
18
20
90 perpendicular
23
20
2. 
A one-way car movement (to the left or counter-clockwise) should be encouraged. A major loop road should be developed around the parking areas. All parking shall be located in bays generally perpendicular to driveways or roads.
3. 
Parking areas or lots providing for more than 60 motor vehicle spaces shall, where possible, be subdivided into modular parking bays. A single row or line of spaces within a bay should be no more than 10 spaces in length. Parking bays should be separated from access or circulation drives by six-foot wide islands for the full width of a bay at the ends of rows.
4. 
In outdoor parking or service areas for uses open to the public, parking spaces shall be striped, lines shall be four inches wide. Such areas shall be curbed with permanent and durable curbing to confine cars to striped parking, without overhang or projection onto sidewalks, driveways, bicycle parking areas, planted areas or adjacent landscaped areas.
5. 
Areas which may be computed as open or enclosed off-street parking spaces include any private garage, carport, or other area available for parking, other than a street, access lane or a driveway. However, a driveway within a required front yard for a one-family residence may count as one parking space. All required parking spaces shall have a vertical clearance of at least seven feet. Curbed islands are required.
a. 
All residential and motel parking shall require every parking space to consist of not less than 162 square feet of usable area and shall be measured exclusive of interior driveway or maneuvering areas. Minimum parking stall width shall be nine feet, minimum length shall be 18 feet.
b. 
All business parking shall require every parking space to consist of not less than 162 square feet of usable area and shall be measured exclusive of interior driveway or maneuvering areas. Minimum parking stall width shall be nine feet, minimum length shall be 18 feet.
c. 
All Marine Commercial Zone parking designated for boating purposes shall permit stacking. A parking lot attendant may be required at all times to assist vehicular entry, exit and use of stacked parking lots. Each space shall require a width of nine feet and a length of 18 feet.
O. 
Bicycle Parking Design Principles.
1. 
Bicycle parking facilities shall be of such a type and quantity so as to encourage and facilitate the use of the bicycle as a means of transportation by the employees and customers of the proposed use requiring site plan approval.
2. 
Outdoor bicycle parking facilities should be located in convenient locations close to building entrances or pedestrian walkways leading to building entrances. Such facilities shall be clearly marked, and separated from automobile access by either landscaping, raised curbs or similar devices. Indoor bicycle parking facilities should be provided in a secure and safe area.
3. 
Bicycle access should be combined with motor vehicle access where possible. Bicycle access driveways or aisles shall not contain hazards to the cyclists (e.g. parallel bar drainage grates, insufficient sight clearance at points of intersection, or insufficient lateral or vertical clearance or radii of curvature).
4. 
Bicycle parking facilities should be located close to major entrances to buildings, or other areas they serve, in view of working personnel on-site or close to high activity areas to minimize chances of theft or vandalism.
P. 
Location and Access of Loading Areas, Berths.
Unobstructed access, at least 10 feet wide, to and from a street shall be provided. Such access may be combined with access to a parking lot. All permitted or required loading areas or berths shall be on the same lot as the use to which they are accessory. No entrance or exit for any loading area or berth shall be located within 50 feet of any street intersection. No off-street loading berth or area shall be located in any front yard.
All areas for the loading and unloading of vehicles and for the servicing of establishments or shops shall be paved and have adequate and unobstructed access from a street, service driveway or alley and shall be so arranged that they may be used without blocking or otherwise interfering with the use of automobile access-ways, parking facilities, fire lanes or sidewalks.
A. 
Street Extensions. The arrangement of streets not shown on the Master Plan or Official Map shall be such as to provide for the appropriate extension of existing streets.
B. 
Minor Streets. Minor streets shall be so designed as to discourage through traffic.
C. 
Right-of-Way. The right-of-way width shall be measured from lot line to lot line and shall not be less than the following:
1. 
Arterial streets, 80 feet.
2. 
Collector streets, 60 feet.
3. 
Minor streets, 50 feet.
4. 
Marginal access streets, 40 feet, or less than the extension of an existing street, as shown on the Official Map, whichever shall be least.
5. 
The right-of-way width for internal roads and alleys in multi-family, commercial and industrial development, shall be determined on an individual basis by the Planning Board, and shall in all cases be of sufficient width and design to safely accommodate the maximum traffic, parking and loading needs and maximum access for firefighting equipment.
D. 
Lots Abutting Existing Streets. Subdivisions that adjoin or include existing streets that do not conform to widths as shown on the Master Plan or Official Map or the street-width requirements of this Ordinance shall dedicate additional width along either one or both sides of said road. If the subdivision is along one side only, 1/2 of the required extra width shall be dedicated.
E. 
Intersections. Street intersections shall be as nearly at right angles as is possible and in no case shall be less than 60°. The block corners at intersections shall be rounded at the curbline, with a curve having a radius of not less than 20 feet. Also, only one point of access and one point of egress may be allowed each property except where large frontages are present. In those latter cases, the Borough Engineer may advise the Planning Board to the safety requirements involved.
F. 
Property Access. Unless necessary to provide access to a lot in separate ownership existing before the date of this Ordinance, no driveway access to property or additional street intersection may be permitted within "sight triangles" as specified herein.
G. 
Street Jogs. Street jogs with center line offsets of less than 125 feet shall be prohibited.
H. 
Reverse Curves. A tangent at least 100 feet long shall be introduced between reverse curves on arterial and collector streets.
I. 
Connecting Street Lines. When connecting street lines deflect from each other at any one point by more than 10° and not more than 45°, they shall be connected by a curve with a radius of not less than 100 feet for minor streets and 300 feet for arterial and collector streets.
J. 
Culs-de-sac. Dead-end streets (culs-de-sac) shall not be longer than 600 feet and shall provide a turnaround at the end with a radius of not less than 50 feet and tangent, whenever possible, to the right side of the street.
K. 
Temporary Culs-de-sac. If a dead-end street is of a temporary nature, a similar turnaround shall be provided and provisions made for future extension of the street and reversion of the excess right-of-way to the adjoining properties.
L. 
Street Names. No street shall have a name which will duplicate as to be confused with the names of existing streets. The continuation of an existing street shall have the same name.
M. 
Alleys. The following shall apply to the design and location of alleys:
1. 
Public alleys shall not be permitted in residential development except by permission of the Planning Board. Where public alleys are permitted in residential developments, they shall be 20 feet wide and paved for the full width.
2. 
Alleys serving commercial and industrial establishments are required unless other provisions for service are approved by the Planning Board. Alleys serving such establishments shall have a paved width of at least 24 feet. If it is impossible for an alley to go through a block, the alley shall be provided with a standard cul-de-sac turnaround at its closed end.
[Ord. No. 1287-2018 § 14]
A. 
Lot Size. Minimum lot size shall be governed by the Zoning Ordinance.
B. 
Lot and House Numbers. House and lot numbers shall be assigned each lot by the Borough Engineer.
C. 
Side Lot Lines. Insofar as is practical, side lot line shall be at right angles to straight streets and radial to curved streets.
D. 
Lot Frontage and Width. Each lot shall front on an approved street accepted by the municipality. Frontage shall be measured along a straight line between points where side lines meet street lines, e.g. the chord of a circle in a cul-de-sac.
E. 
Lot Line on Widened Streets. Where extra width is provided for the widening of existing streets, lot measurements shall begin at such extra width line and all setbacks shall be measured from such line unless otherwise provided by the Zoning Ordinance.
F. 
Unsuitable Lots. Where there is a question as to the suitability of a lot or lots for their intended use, due to factors such as flood conditions or similar circumstances, the Planning Board may, after adequate investigation, withhold approval of such lots. If approval is withheld, the Board shall give reasons and notify the applicant and enter the same into the minutes.
G. 
Concrete Monuments. Concrete monuments shall be installed on both sides of all streets and elsewhere in accordance with the requirements of the N.J. Map Filing Act.
H. 
Existing Platting Pattern. The historic lot orientation of Wildwood Crest places entries facing the north and south directional streets, including Park Boulevard, New Jersey Avenue, Pacific Avenue, Seaview Avenue, Atlantic Avenue, and Ocean Avenue so that the main entry facade or front is facing the primary north south directional street on both interior and corner lots. Conversely, on the east and west directional streets which intersect the north and south directional streets, the main entry facade or front faces the secondary east and west directional streets on interior lots. This historic lot pattern is desirable and creates a sense of enclosure, eyes on the street, and pedestrian scale. Where practical, historic lot layout shall determine that all redevelopment and development respect the existing lot pattern:
1. 
Corner and interior lots along the north and south directional streets shall face the entries to the north and south street;
2. 
Interior lots located along the east and west directional streets shall face the entries to east and west street; except.
3. 
Where this pattern may be impractical due to inconsistencies in block sizes and scale or other established patterns, in which case corner-oriented entries shall be permitted along the north/south streets.
A. 
Utility Installation and Other Easements. Easements along rear property lines or elsewhere for utility installation may be required. Such easements shall be at least 15 feet wide and located in consultation with the companies or municipal departments concerned.
B. 
Drainage and Conservation Easements. Where a subdivision is traversed by a watercourse drainage way channel or street, there shall be provided a stormwater easement or drainage right-of-way conforming substantially with the lines of such watercourse, and such further width or construction or both as will be adequate for the purpose.
C. 
Preservation of Natural or Man-made Assets. Wherever possible, subdividers shall preserve trees, sand dunes, waterways, scenic points, historic spots, and other community assets and landmarks.
D. 
Buffer Areas. If a subdivision abuts an area zoned for a use different from the use permitted in the area of the subdivision, the Planning Board shall consider the need to provide a separation to promote the public safety and general welfare of the municipality. The Planning Board may require a landscape transition buffer as set forth in this Ordinance to be shown on the plat of the subdivision. The Planning Board shall be guided by the design criteria for such buffers as is contained in this Ordinance.
The following construction standards and improvements are necessary to protect the health, safety, welfare, and convenience of the residents and public as well as needed to meet local, County, regional, State and national goals and objectives. It is recognized, however, that in peculiar situations, all of the improvements listed below may not be appropriate or needed.
A. 
Streets. The developer shall submit plans, profiles, cross sections and design for the work to the Borough Engineer for approval prior to the start of any construction; at his own expense, grade all streets for their full width in conformity with the terrain and good engineering practices; shall have all underground utilities installed prior to any street paving construction; shall construct adequate underground pipe drainage systems to carry off surface water; shall construct streets in accordance with specification shown below.
The paved roadway areas shall be constructed in accordance with the following:
1. 
Arterial Streets: As determined by the appropriate agency.
2. 
Collector Streets: Five inch bituminous stabilized base course and three inch type FABC-2 surface course.
3. 
Minor Streets: Four inch bituminous stabilized base course and two inch type FABC-1 surface course.
Prior to placing the surface course, the base course shall have a tack coat of bituminous material. All of the above construction shall be in accordance with current New Jersey Department of Transportation Standard Specifications and supplements thereto on file in the office of the Borough Engineer. The Standard Specifications are further supplemented to require that, prior to placing final surface course, the intermediate base course shall be open to traffic and shall so remain for at least one winter season. Thereafter, the Engineer shall inspect the pavement and will require areas of pavement failure to be removed and replaced, settled areas shall be leveled with hot mixed bituminous concrete. The Engineer may require compacted selected fill or approved sub-base material as needed to replace native subgrade material.
All traffic lanes, both moving and parking, shall be striped in accordance with the Manual on Uniform Traffic Control Devices, as amended. (U.S. Department of Transportation, Federal Highway Administration, 1971.)
B. 
Curbs. Curbs shall be constructed of Portland cement air-entrained concrete, class B, having a standard strength of 4,500 pounds per square inch. Depressed curbs at driveways shall have a full depth of 18 inches.
C. 
Sidewalks. Sidewalks shall be constructed of Portland cement air-entrained concrete, class C, having a standard strength of 4,000 pounds per square inch. Minimum width shall be five feet.
D. 
Water Mains. Water mains are to be installed in accordance with specifications approved by the City of Wildwood Water Utility or the following:
1. 
Engineering requirements for all water main installations are to comply with the rules and regulations of the New Jersey State Department of Health.
2. 
All pipe shall be not less than Class 150 cast-iron pipe of the size determined by the Engineer, but in no case less than six inches in diameter, and meeting the current specifications of the American Water Works Association.
3. 
All joints shall be lead or mechanical joint.
4. 
The depth of pipe from the finished surface or roadway or grade shall be not less than four feet from the top of pipe.
5. 
Fire hydrants shall be installed not greater than 1,000 feet apart at locations approved by the Borough Fire Inspector.
6. 
Valves shall be installed with all fire hydrants and at such other locations in the lines as directed by the Engineer.
7. 
House service connections, from the main to the curb stop and box, must be installed at all lots prior to placing any foundation or surface on the roadway.
8. 
No installation shall be covered until inspected and approved by the Engineer.
E. 
Sewers. Where required by the Planning Board, sanitary sewers including service laterals, shall be installed in all streets and easements before the base materials for the streets are in place or the if the grading of the easement is complete, whether or not such sewers can be put to immediate use. Sewers in the streets and easements are to be constructed in accordance with the following:
1. 
All sewers, manholes, appurtenances and equipment shall be designed, constructed and installed in accordance with the requirements of the Department of Health of the State of New Jersey, the approval of which shall be noted on plans and specifications submitted as part of the data required, and in accordance with the most recent approved specifications and details of the Borough.
2. 
Pipe shall be asbestos cement or cast iron, of the class, type and strength of each required for the particular use and location.
3. 
The minimum inside diameter shall be eight inches for sewers in roadways or easements and five inches for house connections; the diameter and slope (gradient) being such as to maintain theoretically a velocity of two feet per second when flowing 1/2 full (or full) with an assumed n = 0.013. Without special permission of all approving authorities, pipes larger in diameter with flatter slopes shall not be permitted if the project rate of flow does not theoretically fill the pipe 1/2 full.
F. 
Joints. Sections of pipe shall be joined by slip-type rubber gasketed joints, mechanical joints and such other gasketed joints as approved. Hot poured bituminous joints and caulked lead joints may be used, if approved, where conditions are such that preformed gasketed joints are not applicable.
G. 
Watertight Caps of Plugs. Termination of service laterals or any other temporary or permanent opening into the system shall be sealed by an acceptable means against the entrance of surface and ground water. Such sealed caps or plugs shall be so installed as to be watertight against any such internal pressure as might be applied in the testing of the sewer, as well as external subsurface water infiltration. Terminations of laterals shall be referred to "S" cuts on curbs or to other permanent monuments to facilitate locating the ends in the future.
H. 
Manholes. Manholes may be either precast or built in place. No deviation from the approved standards will be permitted which may adversely affect watertightness, structural strength, safe use or maintenance of the manhole or the pipes connecting thereto.
I. 
Service Connections. Laterals for sanitary sewers shall be constructed from mains to a point two feet beyond underground utility easement in front of the realty improvement to be sewered.
The owner shall, at the time he deeds the streets within a development to the Borough, give a bill of sale to the municipality, transferring title to all sewer utility improvements within street line limits and within easement limits absolutely free to Wildwood Crest Borough.
In connection with every site plan, the applicant shall submit plans for all proposed exterior lighting. These plans shall include the location, type of light, radius of light, manufacturer's specification sheet and intensity in foot candles. Adequate lighting shall be provided to insure safe movement of persons and vehicles and for security purposes. The following design standards shall be followed:
A. 
All lighting shall be serviced underground. The style of the light and light standard shall be consistent with the architectural style of the principal building.
B. 
The maximum height of freestanding lights shall be the same as the principal building, but not exceeding 25 feet.
C. 
All lights shall be arranged and shielded in such a manner as not to create a hazard or nuisance to nearby residential properties or the traveling public.
D. 
Where lights along property lines would be visible to adjacent residents, the lights shall be appropriately shielded.
E. 
Light fixtures attached to buildings and visible to the public shall be shielded.
F. 
Freestanding lights shall be so located and protected to avoid being easily damaged by vehicles.
G. 
Lighting shall be located along streets, parking areas, at intersections, and where various types of circulation systems merge, intersect, or split.
H. 
Pathways, sidewalks and trails shall be lighted with low or mushroom type standards.
I. 
Stairways, and sloping or rising paths, building entrances and exits require illumination.
J. 
Lighting shall be provided where buildings are set back or off-set if access is provided at such points.
K. 
The following intensity in foot candles shall be provided:
1. 
Parking Lots. An average of 0.5 foot candles throughout.
2. 
Intersections. Three tenths foot candles.
3. 
Maximum at Property lines. One and zero tenths foot candles.
4. 
Residential Areas. Average of 0.3 foot candles.
Buffers are fences, landscaping, berms and mounds used to minimize any adverse impacts or nuisances on the site or from adjacent areas. They shall be provided in accordance with the provisions as set forth in this Ordinance to include landscape transition buffers and landscape strips. The following design principles shall be considered:
A. 
Evergreens may be used as buffers providing they are planted properly. An evergreen buffer requires two or even three rows of staggered plantings. The rows shall be planted at intervals such that within one complete growing season, visibility from public view is obscured between uses being buffered.
B. 
Fences or walls as buffers shall complement the structural type, design and color of the principal building. A chain link fence with interwoven wood slats is not appropriate for residences or commercial properties.
C. 
Solid fences (solid picket, board and batten, panel or louver types) are most appropriately used adjacent or attached to a building as an extension of its architecture. In such instances, consideration shall be given to coordination with the design theme, materials, and color of the principal structure.
D. 
Semi-transparent fences (one inch by two inches wood screen, picket or contemporary types) are less architecturally related to a principal structure and shall be finished in a more natural manner.
E. 
Transparent fences (hedge, split-rail, wire mesh, chain link types) shall be as unobtrusive as possible and be located within an overall landscaping plan so that they blend into the landscape.
F. 
Plantings shall be considered as part of any wall or fencing plan.
G. 
Consider buffers for the following areas:
1. 
Where interior roads run parallel with roads exterior to the site, a buffer should be erected to prevent confusion, particularly at night.
2. 
Buffer parking areas, garbage collection areas, and loading and unloading areas.
3. 
Consider prevailing wind patterns and use buffers to stop wind-borne debris from leaving the site.
[Ord. No. 1022 § 1B; Ord. No. 1043 § 1; Ord. No. 1101 § 2; Ord. No. 1280-2018]
Signs shall be permitted only in compliance with the following regulations which are intended to provide attractive, coordinated, informative and efficient signs in the Borough.
A. 
General Regulations. The following regulations shall apply to all permitted and pre-existing nonconforming signs:
1. 
No signs shall be hung, erected, rebuilt or placed upon any building or structure unless a zoning permit and/or construction permit has been obtained by the property owner or an authorized agent of owner. Permit applications shall be accompanied by a plan showing details of the sign, type of illumination, type of materials, colors, size and location of the sign on the building and/or parcel.
2. 
All signs shall be kept in good repair which shall include replacement or repair of broken structural elements, casings, or faces, maintenance of legibility and all lighting elements.
3. 
The owner of the premises shall be responsible for keeping the area surrounding ground signs neat, clean and landscaped.
4. 
Directional and State-required signs having areas of less than two square feet are exempt from area and location regulations except they shall be located a minimum of five feet from any property line and further provided they do not constitute a hazard to the traveling public.
5. 
Applications shall comply with all applicable County, State and Federal sign regulations.
6. 
Nonconforming signs shall not be enlarged, changed, or altered in size, location or appearance unless they are to conform to these regulations. Nonconforming signs may be reconstructed or rebuilt with prior approval by the Zoning Officer.
7. 
All principal buildings in all districts shall be clearly identified as to street number by means of a small unobstructed sign, clearly visible and legible from the main and abutting street.
8. 
Letter form and the use of symbols on signs must be simple, bold, and identifiable. The size, location, design, color, texture, lighting, and materials of all temporary and permanent signs and outdoor advertising structures or features shall not detract from the design of proposed buildings and structures and the surrounding properties.
9. 
All signs shall be constructed and placed in such a manner as to insure driver reaction time and safe stopping distance to the entrance of the business or commercial use.
10. 
Every sign shall be in good scale and proportion in design and visual relationship to structures, buildings and other surroundings.
11. 
Every sign shall be designed as an integral architectural element of the structure, building and site to which it principally relates. As an architectural element, a sign shall be in harmony with the structure, building or site's character and use.
12. 
The colors, materials, and lighting of every sign shall be harmonious with the structure, building and site to which it principally relates.
13. 
The number of graphic elements on a sign shall be limited to a minimum needed to convey the sign's main message, and shall be composed in proportion to the area of the sign face.
14. 
Each sign shall be compatible with signs on adjoining premises and shall not compete for attention.
15. 
Awnings are permitted in all zones subject to district/use regulations outlined below.
16. 
Any application for site plan review shall include any proposed temporary and permanent signs.
17. 
Where a sign does not have a panel background, the area of such sign shall be computed by measuring the plane surface lying within the shortest straight lines connecting the exterior points of the letters and ornaments on and of said sign.
18. 
No sign shall be located in the sight triangle, as defined as that area outside of the curbline and the straight line connecting "sight points," one located on each curbline at a distance of 25 feet from the corner.
19. 
Any lighting associated with a sign shall be arranged and shielded in such a manner as not to create a hazard or nuisance to nearby residential properties or the traveling public.
B. 
Prohibited Signs. Signs prohibited in all zones shall specifically include, but not be limited to, the following:
1. 
Any sign which does not pertain to an occupant, service, or product actually occupying or provided on the premises where such sign is located, except for the placement of temporary signs for sale, for rent or open house.
2. 
Roof signs and signs extending above the wall to which they are attached except as where permitted in the M-1 Zone.
3. 
Signs posted on fences, posts, utility poles or trees.
4. 
Signs posted on Borough property without the consent of the Governing Body.
5. 
Signs standing, installed or painted on sidewalks, curbs or the public right-of-way.
6. 
Exterior moving signs or lights of any nature.
7. 
Signs on abutments, retaining walls, embankments, standpipes, water towers or similar structures unless approved by the Governing Body.
8. 
Advertising signs painted directly on buildings, except in the M-1 and B-1 Zones.
9. 
Advertising signs on accessory buildings.
10. 
Advertising signs which constitute a hazard to the traveling public.
11. 
Pylon signs except as permitted herein.
12. 
Billboard signs.
13. 
Throwaways or handbills on porches, in cars, or distributed in any manner as to permit their being blown and littering the streets.
14. 
Automobile, trailer (attached or unattached) or vehicle of any nature bearing signs or advertisements, parked or left for more than 24 hours upon any vacant land or public street.
15. 
Flashing or illuminating signs that spell or present alternating messages.
16. 
Any lighting or control mechanism which may cause radio or television interference.
17. 
All signs operating between the hours of 1:00 a.m. and 6:00 a.m., with the exception of a service sign denoting "Vacancy" no larger than two feet by four feet and the further exception of all signs in the B-1, MC, and M-1 Zones.
18. 
Signs where the actual force of illumination is exposed to public view with the exception of neon.
19. 
Pennants and banners, except for open house, which pennants and banners are not to exceed 16 square feet and are to be removed daily by 4:00 p.m.
20. 
Flags for the purpose of advertising, except for a business in the B-1 and M-1 Zones, and except for open house, which flags shall not exceed 16 square feet and are to be removed daily by 4:00 p.m.
21. 
Signs on balconies or attached to balcony railings.
22. 
All temporary signs shall be prohibited except as outlined below.
C. 
Temporary Signs. Temporary signs in all zones and for all parcels, including vacant lots, shall be subject to the following regulations:
1. 
During construction, no more than one sign total identifying architects, builders, real estate brokers, lending institutions, and contractors is permitted. No sign shall be displayed until municipal approval has been granted and shall be removed when a certificate of occupancy is issued. Maximum size is:
16 square feet for lots up to 12,000 square feet.
32 square feet for lots greater than 12,000 square feet.
The location of the sign's outboard edge shall not be nearer than 1/2 the required setback from any property line, and shall not stand more than six feet from the ground.
Said signs shall be permitted to remain on site for a period not to exceed one year after either the first certificate of occupancy is issued or first deed of conveyance, whichever first occurs.
As part of site plan review by the Planning Board or permit review by the Zoning Officer, proposed temporary signs shall be presented including requests for waivers from the above regulations.
2. 
For sale or rent. No permit shall be required when placed by the property owners or their duly authorized and licensed real estate brokers and meet the requirements below. Vacant ground shall be subject to the regulations below.
For single-family or two-family residential units, one temporary ground-mounted sign shall be permitted per unit announcing that the property on which it is located is for sale or rent, provided such sign shall be displayed for only so long as such property is for sale or rent. Such signs shall not exceed a total of five square feet or two by two 1/2 feet, inclusive of two six inch riders. One information sheet holder is permitted but must be securely attached to the for rent or sale sign. For sale or rent signs shall be located no closer than 10 feet from the curb on residential properties, and the top of the sign shall be no more than four feet above ground level.
For properties in the Motel Zone that contain more than two multi-family residential units, there may be one ground or building-mounted sign advertising for rent or for sale with a maximum size of four by four feet, allowing up to 14 double sided or 28 single sided rider-size six by 18 inches real estate placards per side. Additional signs may be added not to exceed the amount required for one sign per unit. For sale or rent signs shall be located no closer than 20 feet from the curb, and the top of the sign shall be no more than four feet above ground level on multi-family residential properties in the M Zones.
For any properties that are pre-existing and nonconforming as to setbacks and for which placement of "for sale" or "for rent" signs within the setback would present an undue hardship or be impractical to comply with, the Zoning Officer shall have the authority to authorize the placement of the temporary sign within the setback area or to refer applicant to the Zoning Board for waiver or variance relief if deemed necessary.
Two open house signs are permitted on the property that is for sale during the time the open house is taking place and only if an agent or broker is on site. Balloons are permitted attached to the sign during the period of the open house. The open house sign and balloons must be removed at the conclusion of the open house. For open house, the use of either pennants, flags or banners will be allowed only on the property during the open house and must be removed daily no later than 4:00 p.m. All open house signs, pennants or flags or banners or balloons are permitted only on a daily basis between the hours of 10:00 a.m. and 4:00 p.m. to be removed daily.
3. 
Temporary contractor. One temporary window or ground-mounted sign shall be permitted announcing a contractor performing work on a property, only so long as the work is in progress, or three months, whichever is less. Such sign shall not exceed five square feet and shall be located no closer than 10 feet from the curb, and the top of the sign shall be no more than four feet above ground level.
4. 
Temporary political signs shall be permitted in all zones for a period of two months prior to a primary, general and/or special election and for one week thereafter. Said signs shall not exceed 12 square feet and no side of any sign shall be more than six feet in any direction.
D. 
Signs in Business and Marine Commercial Zones. Signs in nonresidential districts may be erected only in accordance with the following requirements:
1. 
Those signs permitted in residential zones.
2. 
Exterior wall signs on nonresidential establishments shall be permitted a total of two signs provided, however, that no single exterior wall of any one establishment shall contain more than one of the two permitted signs. The total sign area for the sign permitted on the face of any wall shall not exceed 5% of the face of the wall area.
3. 
Freestanding signs may be permitted in the B-1 Zone at a maximum of one freestanding sign advertising the business establishments or services located on the lot therein, provided that:
a. 
The area of said sign shall not exceed 16 square feet on each side or surface for lots 40 feet wide or less; and shall not exceed 30 square feet for lots with a width greater than 40 feet.
b. 
The location of said sign's outboard edge shall not be nearer than 1/2 the required setback from any property line.
c. 
The base of said sign shall be appropriately landscaped.
d. 
No freestanding sign shall be erected on a side which borders on a residential zone.
e. 
Freestanding signs may be permitted for marine fishing and marine sightseeing uses directly related to boats provided they do not interfere with pedestrian sidewalk traffic.
4. 
A-frame signs standing on the ground are permitted on the property of the business. They are prohibited on the sidewalk or in the public right-of-way, and they must be on the property that the business is located.
5. 
The location of signs shall not block the view of any existing signs on adjacent properties as seen from the inside travel lane.
6. 
Awnings. Retractable awnings of canvas or similar durable material which are supported within the property lines shall be allowed to extend over a portion of the sidewalk in Business and Marine Commercial Zones. Awning supports are not permitted in the public right-of-way. The vertical clearance from the public right-of-way to the lowest portion of any structural member shall be eight feet. The vertical clearance from the public right-of-way to the lowest portion of any awning, including valances, shall be seven feet minimum. No portion of the awning shall extend more than five feet into the public right-of-way. Awnings shall be constructed and installed in such a manner that upon seasonal or permanent removal, no portion of the support structure shall be exposed.
Awning signs are limited to 16 feet of awning, and letters are limited to eight inches in height. No signs, merchandise, banners or flags shall be attached to the bottom of an awning.
Installation of awnings beyond the property line (in Business and Marine Commercial Zones) is subject to the following:
Any applicant seeking approval to install or replace awnings shall apply for a building permit from the Construction Official setting forth the specific location, dimensions and structural aspects of the proposed awning. The Construction Official shall not issue any awning permit without receiving proper written approval from the Zoning Official, who is hereby authorized to review and, if appropriate, approve awnings after taking into account such factors as impact on the public right-of-way, emergency access and safety, customary activities, drainage and maintenance.
Prior to the erection of any such awning and on an annual basis thereafter with renewal of mercantile license, a liability insurance policy or rider and hold harmless agreement with indemnification to the Borough of Wildwood Crest must be submitted in a form as approved by the Atlantic County Joint Insurance Fund and which must be satisfactory to the Borough Clerk and/or Borough Solicitor.
In emergencies or upon proper notice for any good cause, the Zoning Official is authorized to require the immediate removal of awnings from over any portion of the public right-of-way, all costs of which shall be the sole responsibility of the owner/applicant.
7. 
Window Lettering and Window Signs. For the purpose of enforcing this Ordinance, window lettering and signs shall not be construed as signs, but shall be subject only to the following restrictions:
All window lettering and signs shall be inside the window, and considered interior sign as defined in Article II of this Ordinance.
Permanent window lettering and signs shall be permitted only if the space confining such lettering and signs, or the background, upon which it appears, does not exceed 25% of the window area. Any painted area of any window shall be construed as window lettering or signs, whether or not such area actually contains lettering or advertising.
Window lettering or signs shall pertain only to that establishment occupying that portion of the premises where the window is located. Temporary window lettering or signs, advertising special sales or event, shall be removed within 30 days. Also, such window lettering or signs, in conjunction with permanent window lettering or sign, shall not cover, in the aggregate, more than 30% of the window area.
8. 
Murals may meet the definition of a sign (if there is lettering or images that represent the item or service for sale), therefore must apply for a zoning permit and are subject to the regulation regarding wall signs (above).
9. 
Signs attached to or hung from the principal structure and perpendicular to the street is permitted in the B-1 Zone only with a total sign area of 16 square feet per side.
10. 
Any combination of the permitted signs above must not exceed 100 square feet per property for corner lots, and 75 square feet for inside lots in the B-1 and MC Zones.
11. 
Gasoline service stations and public garages shall be permitted to display only the following signs:
a. 
One temporary sign, located inside the property line, specifically advertising special or seasonal servicing of motor vehicles, provided such sign does not exceed seven square feet in size to a side.
b. 
One nonmoving, freestanding or pylon sign advertising the name of the station or garage and/or the principal products sold, including any special company or brand name, insignia or emblem, provided that the actual sign area does not exceed 30 square feet in size to a side, and further provided that such sign shall be more than 10 feet but less than 20 feet above ground level and is no closer than five feet to any property line.
c. 
Additional signs or lettering displayed over individual entrance doors or bays, bearing legends, essentially the same or similar to the following: "washing, lubrication, repairs, mechanic on duty, car rental, U-hauls." There shall be no more than one such sign over each entrance or bay, such signs shall not exceed six square feet in size, nor shall the lettering on such signs be greater than 12 inches high.
d. 
Customary lettering or other insignia which are an integral part of a fuel pump and consisting only of a fuel name, lead warning sign, price indicator and any other sign or signs as required by law. Such sign shall not exceed three square feet in aggregate area on each pump.
e. 
A single, nonilluminated credit card sign, not exceeding two square feet in size, may be placed on or near each pump island.
E. 
Signs in Hotel/Motel and Multi-Family Zones.
1. 
Hotels/motels and their permitted accessory uses in the motel district shall be permitted to display only the following signs:
a. 
Two signs for the purpose of identification and advertising which shall both be attached to the building, or one attached to the building and one placed on the roof of the building. The total area of these two signs shall not exceed 50 square feet in area. No one sign shall exceed 25 square feet in area. In addition, a freestanding sign is permitted but shall not exceed 25 square feet per side, and shall be set back at least 1/2 of the required setback. Signs mounted on a roof shall not be permitted to extend 10 feet above the topmost point of the roof.
b. 
Hotels or motels containing and maintaining, in connection with the operation thereof, a restaurant, are permitted to erect and maintain two illuminated service display signs advertising the restaurant facilities which sign is not to exceed 16 square feet.
c. 
Where beauty shops and gift shops are permitted in motels, one small, maximum six square feet illuminated sign shall be permitted to advertise services.
d. 
Awnings that are entirely supported by the building may be located within the front yard setback. Any supporting posts may also be located within the front yard setback. Awnings, and support structures are prohibited in the public right-of-way. Lettering and logos are permitted at a maximum of 24 square feet total for the awning.
e. 
A-frame signs standing on the ground are permitted on the property of the motel. They are prohibited on the sidewalk or in the public right of way, and they must be on the property that the motel is located.
2. 
Multi-Family Residential.
a. 
There may be one sign maximum, either affixed to the building or freestanding.
b. 
Maximum area of the sign shall be 25 square feet if the sign is affixed to the building.
c. 
Maximum area of a freestanding sign shall be 12 square feet and shall not stand more than six feet high. It shall be placed no closer to the street than 50% of the setback requirements.
d. 
Awnings that are entirely supported by the building may be located within the front yard setback. Any supporting posts may also be located within the front yard setback. Awnings, and support structures are prohibited in the public right-of-way. Lettering and logos are permitted at a maximum of 24 square feet total for the awning.
e. 
One exterior wall mounted management sign is permitted and shall have a maximum size of three square feet.
F. 
Signs in Residential Districts. Only the following types of signs shall be permitted in residential districts:
1. 
Signs accessory to parking areas for institutional or public uses. Signs designating entrance or exits to or from a parking area shall be limited to one sign for each such exit or entrance, with a maximum size of two square feet for each sign. One sign per parking area designating the conditions of use or identity of such parking area, and limited to a maximum size of six square feet shall be permitted.
2. 
Nameplate and identification signs for single-family dwellings. A sign indicating the name or address of the occupant, or a small professional announcement sign may be permitted provided that the sign shall be no larger than two square feet.
3. 
Institutional Signs. Signs of schools, colleges, churches and other institutions of a similar public or semi-public nature may be erected and maintained provided that:
a. 
The size of any freestanding sign shall not exceed 10 square feet and not more than one such sign is placed on a property, unless such property fronts upon more than one street, in which instance a sign may be erected on each frontage.
b. 
Signs may be affixed to a maximum of two walls of a structure. The total sign area on each wall shall not exceed 25 square feet or 2% of the wall, whichever is less. The wall area shall be measured from ground level to the bottom of the roof eaves and from the side of the building to the other side.
4. 
A sign erected by the Borough, County, State or Federal government.
5. 
Signs used for the protection of the public during construction or repairs.
6. 
Awnings that are entirely supported by the building may be located up to two feet into the required front and side yard setback, and must not fall within six feet of the rear property line. Any supporting posts must meet front and side yard setback requirements, and must not fall within six feet of the rear property line. Lettering or graphics are prohibited on awnings in the residential zone.
G. 
Substandard signs may be removed by the Borough for the following reasons:
1. 
Unsafe Signs. Whenever a sign becomes structurally unsafe or endangers the safety of life or property, the Construction Official shall give either a written or verbal notice that the sign either be made safe or removed. Compliance with the notice shall be immediate if the sign poses imminent danger and the Construction Official or designee shall have the right to remove said sign: otherwise, compliance shall be made within 72 hours. The Borough may charge the owner of the sign for any costs incurred in removing hazardous signs.
2. 
Abandoned Signs. Any individual, corporation or entity who owns or leases a sign shall remove said sign within 30 days after the party advertises that business is no longer conducted in or on the premises, or the party vacates the premises. Removal of the sign can be done in the same manner as described in Subsection G.1 above.
3. 
Illegal Signs. Any sign erected or applied in violation of this Ordinance shall be removed by the owner immediately upon notification with reason by the Zoning Officer or designee. Failure to remove said "illegal" sign shall be cause for the issuance of a summons to appear in Municipal Court.
4. 
Dilapidated Signs. A sign determined to be substantially dilapidated as determined by the Zoning Officer or designee shall be removed in accordance with Subsection G.1 above.
H. 
Municipal Signs. Nothing contained in this chapter shall be construed to apply to any sign, freestanding, installed, painted or erected by the Borough on any Borough premises, lot, structure or facility owned or operated or hereafter owned or operated by the Borough, or by any authority or agency created by the Borough, or within any public street or public right-of-way.
The design and location of all utilities shall be based on Borough standards and the public utility having primary jurisdiction. The location of all utilities shall be coordinated by the Borough Engineer. Storm drainage, sanitary waste disposal, water supply, and solid waste collection and disposal shall be reviewed and considered. Particular emphasis shall be given to the adequacy of existing systems and the need for improvements, on-site, off-site and off-tract, to adequately carry runoff and sewage and to maintain an adequate supply of water at sufficient pressure. All plans shall be approved by the Borough Engineer and shall be in accordance with those detail and design standards on file with the Borough Clerk.
Street furniture are the man-made elements of the environment. These include, but are not limited to, phone booths, benches, planting boxes, mail and meter boxes, lighting standards, directional signs, bollards (posts), fences and walls, water fountains and pools, drinking fountains, trash receptacles and bike racks. In reviewing a site plan, details of street furniture shall include location, size, lighting, and design relationship to principal building(s). Such furniture shall be subordinate to the site plan and arranged in a design-coordinated fashion to the principal use on the lot (e.g. color, scale, bulk shall be reasonably harmonious with the principal building and coordinated with the overall site landscaping plan).
In the site planning and layout of multi-family and higher density residential developments, the following principles, as appropriate, should be considered:
A. 
For townhouse style or similar attached structures, a maximum of six dwelling units in a single row with a minimum offset of two to four feet between every two dwelling units should be encouraged. No more than six dwelling units should be permitted in a straight line. The planes of other straight facades should be no more than 80 feet in length without at least a two-foot offset. Private parking areas should be located near the entrances and outdoor living areas or patios adjoining open space or paths leading to open space. Townhouses and similar style structures in each cluster should be consistent in terms of architectural style and major design elements such as materials, color tones, windows, roof lines, or roof design.
B. 
The site plan should be broken into visually small groupings such as quadrangles, clusters and courts, devices to slow speed and reduce the size of each visual grouping, such as garden walls and gates, reduction in setbacks of facing buildings, and variable landscape layouts.
C. 
Private off-street parking areas shall be located near dwelling unit entrances.
D. 
Architectural elements such as masonry walls and fences shall be compatible, in both style and materials, with the dwelling unit and development of which it is a part.
E. 
Architectural style and major design elements of each dwelling unit, such as materials, color tones, windows, and roof design, shall be compatible with all proposed dwelling units in the immediate neighborhood. Building exteriors shall have vertical and/or horizontal offsets to create visual breaks on the exterior.
F. 
All garages or carports shall conform architecturally to and be of similar materials as the principal building in the development.
G. 
An outdoor private living space shall be provided for each dwelling unit. Buildings shall have open balconies or decks and patios.
H. 
Each building or complex of buildings shall have an architectural theme with appropriate variations in design to provide attractiveness to the development compatible with the development and in its relationship to adjacent land uses. Such variations in design shall result from the use of landscaping and the orientation of buildings to the natural features of the site and to other buildings as well as from varying unit widths, using different exterior materials, changing roof lines and roof designs, varying building heights, and changing window types, shutters, doors, porches, and exterior colors. Architectural elevations shall be submitted to the Planning Board for review and approval.
I. 
All dwelling units shall be connected to approved and functioning water and sanitary sewer systems prior to the issuance of certificate of occupancy.
J. 
No outside area or equipment shall be provided for the hanging of laundry or the outside airing of laundry in any manner. Sufficient area and equipment shall be made available within each building for the laundering and artificial drying of the laundry of the occupants of each building.
K. 
Dwelling units shall have access to a master television antenna system and individual units may not erect individual external television antennas.
L. 
For each apartment unit, in addition to any storage area contained inside individual dwelling units, there shall be provided for each dwelling unit 250 cubic feet of storage area in the cellar, basement, or ground floor of the building where personal belongings and effects may be stored without constituting a fire hazard and where said belongings and effects may be kept locked and separated from the belongings of other occupants.
M. 
No dwelling unit shall be constructed below grade. Units shall be designed in such a manner as to provide maximum security and visual privacy from adjacent dwelling units.
N. 
The use of natural lighting and solar heating is encouraged. Buildings shall be sited so as to take advantage of view, sun and wind factors.
No use generating airborne emissions, activity, operation or device shall be established, modified, constructed or used without having first obtained valid permits and certificates from the Bureau of Air Pollution Control, NJDEP, pursuant to N.J.A.C. 7:27-8. Specifically, no use, activity, operation or device shall be established, modified or constructed without a valid "Permit to Construct." No use, activity, operation or device shall be operated, occupied or used without a valid "Certificate to Operate Control Apparatus or Equipment."
In addition to the requirements of NJDEP, the following shall also apply:
A. 
Particulate matter shall not be discharged into the outdoor air in a concentration exceeding 0.03 grains per cubic foot of gas at actual gas conditions unless a minimum of 95% of such particles leaving the process in the stack gas are removed from the gas prior to discharge. However, regardless of degree of gas cleaning, the following provisions shall apply:
1. 
The concentration of solid particles shall not exceed 0.05 grains per cubic foot at 600° F. and one atmosphere pressure.
2. 
No more than 3% by weight of the particles discharged shall equal or exceed 44 microns in diameter.
3. 
No more than 20 pounds of particulate matter per hour shall be discharged into the outdoor air from any single source.
B. 
Visible emission such as smoke, the shade or appearance of which is darker than No. 1 on the Ringelman Smoke Chart, shall not be emitted into the open air from any fuel-burning equipment; provided, however, that smoke emitted during the clearing of a fire box or the building of a new fire, the shade or appearance of which is not darker than No. 2 on the Ringelman Smoke Chart, may be permitted for a period or periods aggregating no more than three minutes in any 15 consecutive minutes.
A. 
Standard. Noise shall be measured with a sound level meter complying with the standards of The American National Standards Institute, "American Standards Specifications for General Purpose Sound Level Meters" (ANSIS1.4-1961 or its latest revisions). The instrument shall be set to the A-weighted response scale and the meter to the slow response. Measurements shall be conducted in accordance with "American Standard Method for the Physical Measurements of Sound" (ANSIS1.2-1961).
B. 
Noise Level Restrictions. Noises shall not exceed the maximum sound levels specified in the table, except as designated below:
Noise Level Restrictions
Performance Category
Maximum Level Permitted
Where Measured
Residence Districts
55dBA
On or beyond the neighboring use or lot line
All other Districts
65dBA
On or beyond the lot line or district boundaries
In any residence district, the A-weighted sound levels shall not exceed 50 dBA during the hours of 9:00 p.m. and 7:00 a.m. Whenever a residence district abuts any other district, the most restricted of the limitations shall apply.
C. 
Exclusions and Permitted Variations.
1. 
The levels specified in the table may be exceeded once by 10 dB in a single period of 15 minutes, during any one day.
2. 
Peak values of short duration also known as impact noises may exceed the value specified in the table by 20 dB or have a maximum noise level of 75 dBA, whichever is more restrictive.
3. 
Noises such as alarms, sirens, emergency warning devices, are excluded from the above limitations.
A. 
Allowable Illumination. Any operation or activity producing intense glare except for emergency procedures shall be conducted so that direct and indirect illumination from the source shall not exceed 0.3 foot candle in any area zoned residential. Flickering and intense sources of light shall be controlled so as not to cause a nuisance across adjacent lot lines.
B. 
Heat. Sources of heat, including but not limited to steam, gases, vapors, products of combustion or chemical reaction shall not discharge onto or directly contact structures, plant life or animal life on neighboring uses or impair the function or operation of a neighboring use. No use, occupation, activity, operation or device shall cause an increase in ambient temperature, as measured on the boundary between neighboring uses.
A. 
All outdoor storage facilities for fuel, raw materials and products stored outdoors, shall be enclosed by an approved safety fence and suitable landscaping to screen such areas from public view and shall conform to all yard requirements imposed by Borough zoning standards upon the principal buildings in the zone.
B. 
No materials, wastes or other substance shall be stored or maintained upon a lot in such a manner that natural run-off from such areas on a site with an approved stormwater drainage plan can impair the existing water quality of a stream, watercourse or aquifer more than the primary use intended for the lot.
C. 
All materials or wastes which might cause fumes or dust or which constitute a fire hazard or which may be edible or otherwise attractive to rodents or insects shall be stored outdoors only if enclosed in containers which are adequate to eliminate such hazards.
D. 
Except for smoke which is emitted from chimneys, no smoke, fumes or objectionable odors shall be emitted from any building.
E. 
Storage and disposal of hazardous waste materials shall not be permitted in the Borough.
In order to duplicate as nearly as possible natural drainage conditions, regulation and control of stormwater runoff and erosion shall be through on-site stormwater detention and/or ground absorption systems, where possible, which include, but are not limited to, the following:
A. 
Detention areas, which may be depressions in parking areas, excavated basins or basins created through the use of curbs, landscaped areas, or any other form of grading which serves to temporarily impound and store water.
B. 
Rooftop storage through temporary impoundment and storage of stormwater on flat or slightly pitched building rooftops by use of drain outlets which restrict the stormwater runoff from the roof surface.
C. 
Dry wells or leaching basins which control stormwater runoff through ground absorption and temporary storage.
D. 
Porous asphaltic pavement which preserves the natural ground absorption capacity of a site and provides a sub-surface reservoir for temporary storage of stormwater.
E. 
Any system of porous media, such as gravel trenches drained by porous well of perforated pipe, which temporarily stores and dissipates stormwater through ground absorption.
F. 
Any combination of the above mentioned or other techniques, as approved by the Borough Engineer, which serves to limit and control stormwater runoff from a given site.
G. 
The storm system shall be adequate to carry off the stormwater and natural drainage water which originates within the lot or tract boundaries. No stormwater run-off or natural drainage water shall be so diverted as to overload existing drainage systems to create flooding or the need for additional drainage structures on other private properties or public lands without proper and approved provisions being made for taking care of these conditions.
H. 
Techniques for computing water run-off shall be as prescribed by the Borough Engineer.
I. 
Lots shall be graded away from the building(s). Additionally, drainage shall be provided in a manner which will prevent the collection of stormwater in pools or other unauthorized concentrations of flow and water shall not flow across adjacent property lines at greater than predevelopment rates.
Odors shall not be discernible at the lot line or beyond. Any process which may involve the creation or emission of any odors shall be provided with a secondary safeguard system so that control will be maintained if the primary safeguard system should fail.
No use shall obstruct the natural ventilation of adjacent uses nor contaminate the air with excessive heat or odor. Further, no air conditioners or exhaust fans shall be permitted to discharge exhausted air unless set back within the building line.
There shall be no vibration which is discernible to the human senses or which is at low or high frequencies capable of causing discomfort or damage to life or property.
There shall be no toxic or radioactive substances associated with any use.
All electric or electronic devices shall be subject to the provisions of Public Law 90-602, 90th Congress, HR 10790, dated October 18, 1968, entitled "An Act for the Protection of Public Health and Safety from the Dangers of Electronic Product Radiation" and the BOCA Basic Building Code as adopted by the State of New Jersey.
A. 
A soil disturbance review shall be required when an amount of soil exceeding 5,000 square feet or more of disturbance is to be removed or placed upon any site, regardless of the time span to accomplish such removal. Any proposed removal under 5,000 square feet shall be reviewed and approved by the Borough Engineer. However, nothing in this review shall be construed to prevent any owner, otherwise eligible in accordance with law, from excavating or cutting, stripping or otherwise disturbing lands or soil for the following purposes:
1. 
Construction, uses and modifications of a one-family dwelling and its normal accessory and appurtenant uses.
2. 
Gardening for noncommercial purposes.
3. 
Commercial, agricultural or horticultural use when in accordance with accepted farm agricultural practices, approved by the County Soil Conservation District.
4. 
Excavation or cutting, stripping or other land or soil disturbance other than removal from the site necessary for the construction or reconstruction of curbs, sidewalks, private residential driveways, drainage systems, sewage disposal systems and other utility service connections, provided that all other Borough, County, State and district approvals have been received.
5. 
Installation, removal, replacement or maintenance of landscaping, including trees, shrubs, flowers and cover where the existing land contours are not changed by more than one foot.
B. 
In reviewing site plan applications for soil disturbance, the Planning Board shall consider the following criteria:
1. 
Any proposed soil disturbance shall be the minimum necessary consistent with the proper development of the site and shall be done in a manner which will minimize erosion and sedimentation damage and other adverse consequences.
2. 
Physical characteristics of the remaining soil shall be adapted for uses to which the land may lawfully be put.
3. 
Wherever feasible, natural vegetation shall be retained and protected.
4. 
The extent of the disturbed area and the duration of its exposure shall be kept within practical geographic and time limits.
5. 
Either temporary seeding, mulching or other suitable stabilization measures shall be used to protect exposed critical areas during soil disturbance.
6. 
Drainage provisions shall accommodate any increased water runoff resulting from modified soil and surface conditions during and after the soil disturbance.
7. 
Water runoff shall be minimized and retained on site wherever possible to facilitate groundwater recharge and to mitigate possible downstream damage.
8. 
Sediment shall be retained on site to the maximum extent feasible.
9. 
Necessary diversions and sedimentation basins and similar required preventive measures shall be installed prior to any on-site soil disturbance.
10. 
Compliance with minimum standards and specifications contained in Standards for Soil Erosion and Sediment Control in New Jersey and approval of the Soil Conservation Service prior to actual soil disturbance shall be required.
11. 
Dust and mud on the premises in question, as well as on abutting lands shall be prevented or controlled.
12. 
Soil fertility and the resulting ability of the affected area to support plant and tree growth shall be preserved by the preservation of adequate topsoil.
13. 
Necessary lateral support and grades of abutting lands, structures and other improvements shall be maintained.
14. 
Pits and declivities which are hazardous or which provide insect breeding locations shall be avoided.
15. 
The manner of disturbance and/or transportation or removed soil will not adversely affect the public health, safety and general environmental welfare of the Borough.
Monuments shall be installed in compliance with the requirements of N.J.S.A. 46:23-9.11(q). All lot corners shall be marked with a metal alloy pin of permanent character.
Street lighting of a type supplied by the utility and of a type and number approved by the Borough Engineer shall be provided for all street intersections and along all arterial and collector streets and anywhere else deemed necessary by the Planning Board. Wherever this Ordinance requires the underground installation of electric utilities for residential areas, the applicant shall provide for the installation of underground service for street lighting.
[1]
Editor's Note: Former § 85-114, Critical Areas, as amended, was repealed 2-21-2024 by Ord. No. 1422.