Plans are required for all subdivisions and/or land developments
in accordance with the procedures, plan requirements, and design standards
set forth in this chapter.
For the purpose of having a subdivision or land development reviewed and approved by the Planning Commission and Council, the applicant shall file with the Department of Licenses and Inspections the respective plans and applications in accordance with Article
IV of this chapter.
A sketch plan may be submitted in accordance with §
177-14 of this chapter as a basis for informal discussion with the Township staff, and if desired, the Planning Commission, Council, and the Bucks County Planning Commission. The applicant may submit whatever information is deemed useful, however, to facilitate the fullest possible response, it is recommended that the following information be provided on sketch plan submissions:
A. Name of
the subdivision or land development.
B. Tax parcel
number, recommended to be shown directly beneath the name of the subdivision
or land development.
C. Name and
address of the legal and equitable owners, and the applicant.
D. Name and
address of the registered engineer, land surveyor, architect or landscape
architect who prepared the plan.
E. A brief
description of the proposal.
F. Tract boundaries
and size.
G. North point,
date, and scale.
I. Significant
topographical and physical features, including contours based on U.S.
Coast and Geodetic maps or site survey.
J. Streets
on and adjacent to the tract.
K. Proposed
general street layout.
L. Proposed
general lot layout or building layout with parking lots and open spaces
indicated.
M. Zoning
district boundaries, with particular reference to areas of the subject
tract within floodplain zones, as designated in the Zoning Ordinance.
The preliminary plan shall be submitted in accordance with §
177-14 of this chapter and shall show or be accompanied by the following information:
A. Drafting
standards.
(1) The
plan shall be drawn at a scale of one inch equals 50 feet or one inch
equals 100 feet and shall be a clear and legible print;
(2) Dimensions
shall be set in feet and decimal parts thereof, and bearings in degrees,
minutes and seconds;
(3) Each
sheet shall be numbered and shall show its relationship to the total
number of sheets;
(4) Where
any revision is made, or when the plan is a revision of a previously
approved plan, dotted lines shall be used to show features or locations
to be abandoned and solid lines to show the presently proposed features.
All revisions shall be noted in a revision block with the revision
date, a note of explanation and reference to the page on which the
revision is to be found;
(5) The
plan shall be so prepared and bear an adequate legend to indicate
clearly which features are existing and which are proposed;
(6) The
boundary line of the subdivision or land development shall be shown
as a solid heavy line;
(7) Preliminary
plans shall be on sheets either 18 inches by 24 inches, 24 inches
by 36 inches, 30 inches by 42 inches, or 36 inches by 48 inches and
all lettering shall be so drawn as to be legible if the plan should
be reduced to half size. The plan shall be labeled "Preliminary Plan
- Not to be Recorded."
B. General
information to be shown.
(1) Name
of the subdivision or land development;
(2) Tax
parcel number shown directly beneath the name of the subdivision or
land development;
(3) Name
and address of the legal and equitable owners and the applicant;
(4) Name
and address of the registered engineer, land surveyor, architect,
or landscape architect who prepared the plan;
(5) A brief
description of the proposal;
(6) Total
acreage of the tract;
(7) Present
zoning classification with district boundaries and requirements including
lot size and yard requirements and proof of any variances or special
exceptions that may have been granted by the Township Zoning Hearing
Board;
(8) Date,
North point, and scale;
(9) A location
map for the purpose of locating the site to be subdivided or developed
at a scale of not less than 800 feet to the inch showing the relation
of the tract to all adjoining properties and streets, roads, and municipal
boundaries existing within 1,000 feet of any part of the property
proposed to be subdivided or developed.
C. Existing
features.
(1) Complete
outline survey of the property to be subdivided or developed, showing
all courses, distances, areas, and tie-ins to all adjacent street
intersections;
(2) The
names of owners, tax parcel numbers, and zoning classification of
land immediately adjacent to or across from the tract;
(3) The
location, names, and widths of streets, the location and name of railroads,
the location of sanitary sewers, storm drains, water mains, culverts,
petroleum or petroleum product lines, gas lines, electric and telephone
lines, fire hydrants, and all other utilities or significant man-made
features on or within 200 feet of any part of the tract;
(4) Location
of all existing monuments with references to them;
(5) Location,
size and ownership of all underground utilities, and any rights-of-way
or easements within the property. All underground utility lines shall
be shown on the plan pursuant to Act 287 of 1974, as amended by Act
187 of 1996, along with a notation that the utility company be contacted
prior to construction;
(6) Appropriate
contours at two-foot to five-foot intervals with sufficient details
to show the course, structure, and capacity of all drainage facilities,
and the method of drainage of the adjacent or contiguous properties.
All ground contours shall be taken from U.S. Coast and Geodetic bench
marks and run direct to the degree that the actual elevations of the
contours shall be the exact elevations above U.S. Coast and Geodetic
data;
(7) Location
of existing buildings and/or structures, the use of each building/structure,
existing wells, on-lot sewage disposal systems, driveways, parking
and other existing paved areas;
(8) Identification
of all historically significant buildings or structures on the tract
and/or any adjacent property;
(9) Location
of species and size of large trees (greater than eight inches caliper
at a height of three feet above the ground) standing alone. The location
and area of all floodplains, floodplain soils, woodlands, bodies of
water, watercourses, wetlands, slope areas over 15%, boundaries of
all soil types with a description of each type indicating any limitations
of the soil type for on-site sewage disposal, buildings with basements,
streets and parking lots.
D. Proposed
layout.
(1) Lot
layout, including dimensions and bearings, and consecutive numbering
of lots;
(2) The
layout of streets, including name and width of streets, rights-of-way,
alleys, and crosswalks and sidewalks;
(3) For
land developments, the proposed location and dimensions of buildings,
parking areas, service areas, lighting standards, sidewalks, fire
hydrants, and trash receptacles;
(4) A reference
to any land dedicated for public use, or offered for dedication for
parks, recreation areas, schools, widening of streets, or other public
uses;
(5) For
multifamily developments, the total area, total dwelling units, number
of buildings, proposed density, total parking spaces, building coverage
and the bedroom ratio (percentage of total units with one bedroom,
two bedrooms, etc.), and other requirements of the Zoning Ordinance;
(6) For
subdivisions, the total area, number of lots, density, lot area for
each lot, average and minimum lot size, and proposed length of new
streets;
(7) Location
and size of proposed storm drains, sanitary sewers, culverts, watercourses,
and all appurtenances thereof, on-site sewage disposal facilities,
gas mains, water mains, fire hydrants, streetlights, planting, special
structures, and other underground conduits or structures;
(8) A plan for the surface drainage of the tract, which shall also indicate the impervious surface ratio. A plan to control erosion during and after the construction period shall be required as provided in §
177-48 of this chapter;
(9) Building
setback lines, established by zoning or other ordinances, or deed
restrictions, with distances from the proposed right-of-way lines;
(10) An
indication of any lots on which other than a residential use is intended;
(11) Rights-of-way
and/or easements proposed to be created for all drainage purposes,
utilities, or other pertinent reasons;
(12) Tentative
typical cross sections and center line profiles of each proposed street
shown on the preliminary plan. These plans may be submitted as separate
sheets;
(13) A landscape plan showing proposed contours and required street trees, parking lot plantings, buffer, plant schedule, and other required plantings in accordance with §
177-51 of this chapter;
(14) Where
the preliminary plan covers only a part of the applicant's entire
holding, a sketch shall be submitted of the prospective street layout
for the remainder;
(15) Method
of calculating the total number of off-street parking spaces;
(16) Transportation impact study. A transportation impact study shall be submitted as part of the preliminary plan application for all subdivision and/or land development proposals that meet criteria established in §
177-57 of this chapter;
(17) Tree
protection zone.
(a) The location of all trees to be saved, including their trunk and
dripline locations. Driplines should be plotted accurately, to scale.
When groups of trees are to be saved, only the locations of the trees
on the perimeter must be shown;
(b) The tree protection zone shall be shown on the plan;
(c) The location of proposed protection fencing and/or retaining walls
around trees shall be shown;
(d) Construction details of all retaining walls shall be provided, including
special soils and fill mediums where applicable. Any grade changes
which would alter surface and/or subsurface water movement either
to or from the tree protection zone must be indicated.
(18) A stormwater plan as required in§
177-50 of this chapter.
The final plan shall be submitted in accordance with §
177-14 of this chapter and shall show or be accompanied by the following information:
A. Drafting
standards.
(1) The
plan shall be drawn at a scale of one inch equals 50 feet or one inch
equals 100 feet, and shall be a clear and legible print;
(2) Dimensions
shall be set in feet and decimal parts thereof, and bearings in degrees,
minutes, and seconds;
(3) Each
sheet shall be numbered and shall show its relationship to the total
number of sheets;
(4) Where
any revision is made, or when the plan is a revision of a previously
approved plan, dotted lines shall be used to show features or locations
to be abandoned and solid lines to show the presently proposed features.
All revisions shall be noted in a revision block with the revision
date, a note of explanation and reference to the page on which the
revision is to be found;
(5) The
plan shall be so prepared and bear an adequate legend to indicate
clearly which features are existing and which are proposed;
(6) The
boundary line of the subdivision or land development shall be shown
as a solid heavy line;
(7) Final
plans shall be on sheets either 18 inches by 24 inches, 24 inches
by 36 inches, 30 inches by 42 inches, or 36 inches by 48 inches and
all lettering shall be so drawn as to be legible if the plan should
be reduced to half size.
B. General
information to be shown.
(1) Name
of the subdivision or land development;
(2) Tax
parcel number should be shown directly beneath the name of the subdivision
or land development;
(3) Name
and address of the legal and equitable owners and the applicant;
(4) Name
and address of the registered engineer, land surveyor, architect,
or landscape architect who prepared the plan;
(5) A brief
description of the proposal;
(6) Total
acreage of the tract;
(7) Present
zoning classification with district boundaries and requirements including
lot size and yard requirements and proof of any variances or special
exceptions which may have been granted by the Township Zoning Hearing
Board;
(8) Date,
North point, and scale;
(9) A location
map for the purpose of locating the site to be subdivided or developed
at a scale of not less than 800 feet to the inch showing the relation
of the tract to all adjoining properties and streets, roads and municipal
boundaries existing within 1,000 feet of any part of the property
proposed to be subdivided or developed.
C. Existing
features.
(1) Complete
outline survey of the property to be subdivided or developed, showing
all courses, distances, areas, and tie-ins to all adjacent street
intersections;
(2) The
names of owners, tax parcel numbers, and zoning classification of
land immediately adjacent to or across from the tract;
(3) The
location, names, and widths of streets, the location and name of railroads,
the location of sanitary sewers, storm drains, water mains, culverts,
petroleum or petroleum product lines, gas lines, electric and telephone
lines, fire hydrants, and all other utilities or significant man-made
features on or within 200 feet of any part of the tract;
(4) Location
of all existing monuments with references to them;
(5) Location,
size and ownership of all underground utilities, and any rights-of-way
or easements within the property. All underground utility lines shall
be shown on the plan pursuant to Act 287 of 1974, as amended by Act
187 of 1996, along with a notation that the utility company be contacted
prior to construction;
(6) Appropriate
contours at two-foot to five-foot intervals with sufficient details
to show the course, structure, and capacity of all drainage facilities,
and the method of drainage of the adjacent or contiguous properties.
All ground contours shall be taken from U.S. Coast and Geodetic bench
marks and run direct to the degree that the actual elevations of the
contours shall be the exact elevations above U. S. Coast and Geodetic
data;
(7) Location
of existing buildings and/or structures, the use of each building/structure,
existing wells, on-lot sewage disposal systems, driveways, parking
and other existing paved areas;
(8) Identification
of all historically significant buildings or structures on the tract
and/or any adjacent property;
(9) Location
of species and size of large trees (greater than eight inches caliper
at a height of three feet above the ground) standing alone. The location
and area of all floodplains, floodplain soils, woodlands, bodies of
water, watercourses, wetlands, slope areas over 15%, boundaries of
all soil types with a description of each type indicating any limitations
of the soil type for on-site sewage disposal, buildings with basements,
streets and parking lots.
D. Proposed
layout.
(1) Lot
layout, including dimensions and bearings, and consecutive numbering
of lots;
(2) The
proposed names, cartway width, and right-of-way width of all proposed
streets;
(3) For
land developments, the proposed locations and dimensions of buildings,
parking areas, service areas, lighting standards, sidewalks, fire
hydrants, and trash receptacles;
(4) A reference
to any land dedicated for public use or offered for dedication for
parks, recreation areas, schools, widening of streets, or other public
uses;
(5) For
multifamily developments, the total area, total dwelling units, number
of buildings, proposed density, total parking spaces, building coverage,
and the bedroom ratio (percentage of total units with one bedroom,
two bedrooms, etc.), and other requirements of the Zoning Ordinance;
(6) For
subdivisions, the total area, number of lots, density, lot area for
each lot, average and minimum lot size, and proposed length of new
streets;
(7) Location
and size of proposed storm drains, sanitary sewers, culverts, watercourses,
and all appurtenances thereof, on-site sewage disposal facilities,
gas mains, water mains, fire hydrants, streetlights, monuments, special
structures, and other underground conduits or structures;
(8) A plan for the surface drainage of the tract which shall also indicate the impervious surface ratio. A plan to control erosion during and after the construction period shall be provided as required in §
177-48 of this chapter;
(9) Building
setback lines, established by zoning or other ordinances, or deed
restrictions with distances from the proposed rights-of-way lines;
(10) An
indication of any lots on which other than a residential use is intended;
(11) Rights-of-way
and/or easements proposed to be created for all drainage purposes,
utilities, or other pertinent reasons;
(12) A landscape plan showing proposed contours and required street trees, parking lot plantings, buffer, plant schedule, and other required plantings in accordance with §
177-51 of this chapter;
(13) Method
of calculating the total number of off-street parking spaces;
(14) Tree
protection zone.
(a) The location of all trees to be saved, including their trunk and
dripline locations. Driplines should be plotted accurately, to scale.
When groups of trees are to be saved only the locations of the trees
on the perimeter must be shown;
(b) The tree protection zone;
(c) The location of proposed protection fencing and/or retaining walls
around trees;
(d) Construction details of all retaining walls, including special soils
and fill mediums where applicable, any grade changes which would alter
surface and/or subsurface water movement either to or from the tree
protection zone.
(15) A stormwater plan as required in§
177-50 of this chapter;
(16) For
on-lot facilities, the location of water supply and sewage disposal;
(17) Certification
of water and sewer facilities from the serving authority. Indication
of compliance with the Pennsylvania Sewage Facilities Act, Act 537,
approved January 24, 1966, as amended;
(a) Public sewer. Certification from the appropriate authority indicating
that sewerage service system and capacity are available for lots proposing
to use a public sewerage system. A letter of approval from the Pennsylvania
Department of Environmental Protection (PaDEP) is also required.
(b) On-lot sewer. A site suitability report conducted by the Bucks County
Department of Health and a letter of approval from the Pennsylvania
Department of Environmental Protection (PaDEP) certifying that the
proposal is consistent with the Pennsylvania Sewage Facilities Act.
E. Improvement
Construction Plan (Drainage and Construction):
(1) The
improvement and construction plan shall be at any of the following
scales:
Horizontal
|
Vertical
|
---|
50 feet/inch
|
5 feet/inch
|
100 feet/inch
|
10 feet/inch
|
(2) Center
line with bearings, distances, curve data and stations corresponding
to the profile;
(3) Right-of-way
and curblines with radii at intersections;
(4) Beginning
and end of proposed construction;
(5) Tie-ins
by courses and distances to intersection of all public roads, with
their names and widths;
(6) Location
of all monuments with reference to them;
(7) Property
lines and ownership of abutting properties;
(8) Location
and size of all drainage structures, public utilities, lighting standards,
and street name signs;
(10) Profile
(streets):
(a) Profile of existing ground surface along center line of street;
(b) Proposed center-line grade with percent of tangents and elevations
at fifty-foot intervals, grade intersection and either end of curb
radii;
(c) Vertical curve data including length, elevation, and minimum sight
distance as required by the Township Engineer;
(11) Cross
sections:
(a) Right-of-way width and location and width of paving;
(b) Type, thickness, and crown of paving;
(d) Grading of sidewalk area;
(e) Location, width, type and thickness of sidewalks;
(f) Typical location of sewers and utilities with sizes;
(12) Horizontal
plan (storm drains and sanitary sewers):
(a) Location and size of line with stations corresponding to the profile;
(b) Location of manholes or inlets with grade between and elevation of
flow line and top of each manhole or inlet;
(c) Property lines and ownership, with details of easements where required;
where easements are required, property lines and ownership should
be shown;
(d) Beginning and end of proposed construction;
(f) Location of all other drainage facilities and public utilities in
the vicinity of storm and/or sanitary sewer lines;
(g) Hydraulic testing data for culverts and/or bridge structures;
(13) Profile
(storm drains and sanitary sewers):
(a) Profile of existing ground surface with elevations at top of manholes
or inlets;
(b) Profile of storm drain or sewer showing type and size of pipe, grade,
cradle, manhole, inlet locations, and elevation at flow line;
(c) Individual lot grading plans shall be approved by the Township Engineer
prior to issuance of a building permit.
The minor subdivision plan shall be submitted in accordance with §
177-14 of this chapter and shall show or be accompanied by the following information:
A. Drafting
standards.
(1) The
plan shall be drawn at a scale of one inch equals 50 feet or one inch
equals 100 feet and shall be a clear and legible print;
(2) Dimensions
shall be in feet and decimal parts thereof, and bearings shall be
in degrees, minutes, and seconds;
(3) Each
sheet shall be numbered and shall show its relationship to the total
number of sheets;
(4) Where
any revision is made, or when the plan is a revision of a previously
approved plan, dotted lines shall be used to show features or locations
to be abandoned and solid lines to show the proposed features. All
revisions shall be noted in a revision block with the revision date,
a note of explanation and reference to the page on which the revision
is to be found;
(5) The
plan shall be so prepared and bear an adequate legend to indicate
clearly which features are existing and which are proposed;
(6) The
boundary line of the subdivision shall be shown as a solid heavy line;
(7) Minor
subdivision plans shall be on sheets either 18 inches by 24 inches,
24 inches by 36 inches, 30 inches by 42 inches, or 36 inches by 48
inches, and all lettering shall be so drawn as to be legible if the
plan should be reduced to half size.
B. General
information to be shown.
(2) Tax
parcel number shown directly beneath the name of the subdivision;
(3) Name
and address of the legal and equitable owners and the applicant;
(4) Name
and address of the registered professional engineer, land surveyor,
architect, or landscape architect who prepared the plan;
(5) A brief
description of the proposal;
(6) Total
acreage of the tract;
(7) Present
zoning classification with district boundaries and requirements including
lot size and yard requirements and proof of any variances or special
exceptions which may have been granted by the Township Zoning Hearing
Board;
(8) Date,
North point, and scale;
(9) A location
map for the purpose of locating the site at a scale of not less than
800 feet to the inch showing the relation of the tract to all adjoining
properties and streets, roads and municipal boundaries existing within
1,000 feet of any part of the tract to be subdivided.
C. Existing
features.
(1) Complete
outline survey of the property to be subdivided, showing all courses,
distances, areas, and tie-ins to all adjacent street intersections;
(2) The
names of owners, tax parcel numbers, and zoning classification of
land immediately adjacent to or across from the tract;
(3) The
location, names, and widths of streets; the location and names of
railroads; the location of sanitary sewers, storm drains, water mains,
culverts, petroleum or petroleum product lines, gas lines, electric
and telephone lines, fire hydrants, and all other utilities or significant
man-made features on or within 200 feet of any part of the tract;
(4) Location
of all existing monuments with references to them;
(5) Location,
size, and ownership of all underground utilities and any rights-of-way
or easements within the property. All underground utility lines shall
be shown on the plan pursuant to Act 287 of 1974, as amended by Act
187 of 1996, along with a notation that the utility company be contacted
prior to construction;
(6) Appropriate
contours at two-foot to five-foot intervals with sufficient details
to show the course, structure, and capacity of all drainage facilities,
and the method of drainage of the adjacent or contiguous properties.
All ground contours shall be taken from U.S. Coast and Geodetic bench
marks and run direct to the degree that the actual elevations of the
contours shall be the exact elevations above U.S. Coast and Geodetic
data;
(7) Location
of existing buildings and/or structures, the use of each building/structure,
existing wells, on-lot sewage disposal systems, driveways, parking
and other existing paved areas;
(8) Identification
of all historically significant buildings or structures within the
property or any adjacent property;
(9) Location
of species and size of large trees (greater than eight inches caliper
at a height of three feet above the ground) standing alone. The location
and area of all floodplains, floodplain soils, woodlands, bodies of
water, watercourses, wetlands, slope areas over 15%, boundaries of
all soil types with a description of each type indicating any limitations
of the soil type for on-site sewage disposal, buildings with basements,
streets and parking lots.
D. Proposed
layout.
(1) Lot
layout, including dimensions and bearings, and consecutive numbering
of lots;
(2) The
total area, number of lots, and lot sizes;
(3) Building
setback lines, established by zoning or other ordinances, or deed
restrictions, with distances from the proposed right-of-way lines;
(4) A reference
to any land dedicated f'or public use, or offered for dedication for
parks, recreation areas, schools, widening of streets or other public
uses;
(5) An
indication of any lots in which other than a residential use is intended;
(6) Rights-of-way
and/or easements proposed to be created for all drainage purposes,
utilities, or other pertinent reasons;
(7) The location of required plantings in accordance with§
177-51 of this chapter;
(8) For
on-lot facilities, the location of water supply and sewage disposal;
(9) Certification
of water and sewer facilities from the serving Authority. Indication
of compliance with the Pennsylvania Sewage Facilities Act, Act No.
537, approved January 24, 1966, as amended;
(a) Public sewer. Certification from the appropriate authority indicating
that sewerage service system and capacity are available for lots proposing
to use a public sewerage system, a letter of approval from the Pennsylvania
Department of Environmental Protection (PaDEP) is also required.
(b) On-lot sewer. A site suitability report conducted by the Bucks County
Department of Health and a letter of approval from the Pennsylvania
Department of Environmental Protection (PaDEP) certifying that the
proposal is consistent with the Pennsylvania Sewage Facilities Act.
(10) Tree
protection zone.
(a) The location of all trees to be saved, including their trunk and
dripline locations. Driplines should be plotted accurately, to scale.
When groups of trees are to be saved only the locations of the trees
on the perimeter must be shown;
(b) The tree protection zone;
(c) The location of proposed protection fencing and/or retaining walls
around trees;
(d) Construction details of all retaining walls, including special soils
and fill mediums where applicable, and any grade changes which would
alter surface and/or subsurface water movement either to or from the
tree protection zone.
The record plan shall be clear and legible blue or black line print and shall be an exact copy of the approved final plan on a sheet of the size required for final plans. The following information shall appear on the record plan, in addition to the information required in §
177-93.
A. Seals:
(1) The
impressed seal of the licensed engineer, land surveyor, architect,
or landscape architect who prepared the plan;
(2) The
impressed corporate seal, if the applicant is a corporation;
(3) The
impressed seal of a notary public or other qualified officer acknowledging
applicant's statement of intent;
(4) The
impressed Seal of Bristol Township.
B. Acknowledgments:
(1) A statement
to the effect that the applicant is the owner of the land proposed
to be subdivided or developed and that the subdivision or land development
shown on the final plan is made with the applicant's consent and that
it is desired to record the same;
(2) An
acknowledgment of said statement before an officer authorized to take
acknowledgments.
C. The following
signatures shall be placed directly on the record plan in black ink:
(1) The
signature of the licensed engineer, land surveyor, architect, or landscape
architect who prepared the plan.
(2) The
signature of the owner or owners of the land; if the owner of the
land is a corporation the signatures of the president and secretary
of the corporation shall appear in the following approved notation:
To all whom these presents may come, I (we) _______________
send greetings. Know ye that I (we) have laid out upon my (our) lands,
situate in the Township of Bristol, County of Bucks and Commonwealth
of Pennsylvania, intended to be forthwith recorded. Witness my (our)
hand and seal this _______________ day of ________________, _______.
|
(3) The
signature of the notary public or other qualified officer, acknowledging
the owner's statement of intent in the following approved notation:
Commonwealth of Pennsylvania, County of Bucks, on the ________________
day of _______________,__________, before me, the subscriber, a notary
public of the Commonwealth of Pennsylvania, personally appeared _______________,
who acknowledged this plan to be the official plan of property shown
hereon, situate in the Township of Bristol, County of Bucks and Commonwealth
of Pennsylvania and desired that this plan be recorded according to
law.
|
Notary Public
|
My Commission Expires
|
(4) The
signatures of the Chairman and Secretary of the Township Planning
Commission in the following approved notation:
Approved by the Bristol Township Planning Commission this
|
_______________ day of ________________, __________.
|
|
|
(5) The
signature of the Township Engineer in the following approved notation:
Reviewed by the Bristol Township Engineer this ________________
day of _______________,_______.
|
|
|
(6) The
signature of the President and Secretary of Council in the following
approved notation:
Approved by the Bristol Township Engineer this ________________
day of _______________, _______
|
|
|
(7) The
signature of the Executive Director of the Bucks County Planning Commission
or his designees in the following approved notation:
BCPC No. __________
|
Processed and Reviewed. Report prepared by the Bucks County
Planning Commission in accordance with the Pa Municipalities Planning
Code.
|
Certified this date _______________
|
|
(8) The
signature of the Office of the Recorder of Deeds in the approved recording
notation:
Recorded in the Office of the Recorder of Deeds at Doylestown,
Pennsylvania in plan book __________ page __________ on the _______________
day of _______________, _______.
By _______________
|