All materials used for plumbing installation work shall be free from detrimental defects and shall conform to the regulations of the Plumbing Inspector.
A. 
No material, device, fixture, method of assemblage, installation, appurtenance or appliance other than those specified or permitted by the regulations issued hereunder shall be installed unless it has been approved by the Plumbing Inspector and is installed in conformity with the conditions of such approval.
B. 
If it is impractical to conduct adequate tests prior to installation, the Plumbing Inspector may grant tentative approval and permission to make the installation as proposed, but final approval shall not be given until tests conducted after installation show that the material, device, fixture, method or assemblage, installation, appurtenance or appliance meets the intent of these regulations, functions as required and conforms to the conditions of approval set forth by the Plumbing Inspector when granting tentative approval.
C. 
Materials for plumbing installation shall be deemed approved when they conform to the standard specifications for materials hereinafter set forth in § 131-13.
A. 
Whenever the approved standard under which a material, fixture or device is approved requires that the item be identified in a specified manner as to weight or quality, such identification shall be provided and shall be of a reasonably permanent nature. Copper tubing shall have an identification mark (as to type) every two feet.
B. 
Solder and solder fluxes shall have labels stating: "Contains 0.20% or less lead."
Brass caulking ferrules shall be of brass pipe conforming to the specifications listed in § 131-13 or of heavy cast brass of the weight and dimensions given in the following table. Brass caulking ferrules for copper water tube shall conform to the specifications listed in § 131-13. Seamless copper ferrules may be used in lieu of cast brass, provided that they correspond in size and weight.
Brass Caulking Ferrules
Pipe Size
(inches)
Actual Inside Diameter
(inches)
Minimum Length
(inches)
Minimum Weight
(ounces)
2
2 1/4
4 1/2
16
3
3 1/4
4 1/2
28
4
4 1/4
4 1/2
40
Floor flanges for water closets, pedestal urinals, trap standard service sinks and other similar floor-connected fixtures with trap standards shall be of an approved type, shall conform to § 131-23E and shall not be less than 1/4 inch thick when of cast iron or galvanized malleable iron and not less than 1/8 inch thick when of brass or hard lead.
A. 
Materials for plumbing installations shall conform to the following specifications:
Materials for Plumbing Installations
Specification
Material
ANSI
ASTM
FS
Others
Clay sewer pipe (standard strength)
C13-65T
Clay sewer pipe (extra strength)
C200-65T
Vitrified clay pipe joints
C425-64
Concrete sewer pipe
C14-65
Cast-iron soil pipe and fittings
A74-66
Cast-iron water pipe
A377-66
Cast-iron screwed pipe
A40.5-43
WW-P-356
Cast-iron drainage fittings
B16.12-65
WW-P-491a
Cast-bronze solder drainage fittings
B 16.23-60
Joints (screwed)
B2.1-60
B2.2-60
GGG-P351a
Joints (brazed)
B31.1-55
B3.1.1(a)65
Jiffey joint
C564-65T
Zytel mechanical coupling # 7010-33
DL-401-B (manufacturers' standards)
O-ring, gasket (PVC and neoprene)
C443, C425, C594, C564, D1869
Wrought-iron pipe
A72-64T
Yoloy pipe (galvanized)
A53
1506-1965 (manufacturers' standards)
Steel pipe (galvanized)
A120-65
Malleable iron screwed fittings
B16.3-63 (150#)
WW-P-521e-64
Brass pipe
B43-62
Seamless brass tube
B135-63
Brass caulking ferrules
B43-62
Rough brass screwed fittings
B16.1564
471a-64
Copper drainage tube (Type DWV)
H23.6-67
B306-66A
CS229-60
Copper water tube (types K.L and M)
H23.1-67
B88-66a
WW-T-799a
Seamless copper tubing
875-65
Soldered fittings (for copper water tube)
B16.1863
Flared fittings (for copper water tube)
B16.26.58
Temp-tite (pressure pipe)
C296
C428
AWWAC-400
SS-P-331B
SS-P-351A
Stainless steel tube copper coated
TP-430
DWV Grade G Code Orange
TP-409
Water pipe Grade H Code Blue
B254-23
Lead traps and bends
WW-P-325
CS9641
Hard lead closet flanges
LIA
Caulking lead
B2955
Sheet lead (minimum weight 4 pounds per square foot)
OO-L-201d-61
Sheet brass
B3661
Sheet copper
B15260
Soldering nipples
B4362
Lead brass and strip
B12160
Chemical stoneware pipe and fittings
Manufacturers' standards
Chemical porcelain pipe and fittings
Manufacturers' standards
Borosillicate glass fittings
Manufacturers' standards
Galvanized pipe and fittings
A 120-65
A 90-66
Coal tar enamel protective coating
D1187-66
Solder for potable water
B32-83, Alloy Grades Sn 96 or Sb5
Lead content: 0% maximum, cadmium content: 0% maximum
Solder for other uses
B32-83
Solder flux for potable water
Lead content: 0% maximum: cadmium content 0% maximum
Fixture setting compound
HH-C-563a-54
WW-P-541b-54
Valves, bronze, gate
B61-63
Valves, Cast-iron, gate
A126-66
Acid-resisting cast-iron pipe and fittings
A518-64
Air gaps in plumbing systems
A40.4-42
Backflow preventers
A40.6-43
Temperature and pressure relief valves
Z21.10 1-67
Saran-lined steel pipe and fittings
Manufacturers' standards
Modified epoxy resin, cast, thermosetting pipe and fittings
Manufacturers' standards
Stainless steel, mechanical joint coupling with resilient sleeve and teflon liner
Manufacturers' standards; minimum 2 inches wide
Malleable iron split coupling with synthetic rubber gasket
A47, Grade 32510
Manufacturers' standards
Nylon resin cleanout plugs
Military Specification M-206 93A Type 1
Elastorneric, compression-type, one-piece gaskets
C564-65T
Plastic water service, polyvinyl chloride (PVC) pipe and fittings
B72.2-67
D1785-68
L-P-1036-(1)-1968
CS207-60
CS256-63
NSF14-65
PVC sewer pipe, polyvinyl chloride (PVC) Schedule 40 pipe and fittings
D2265-68
L-P-320a-66
CS272-65
NSF14-65
ABS Schedule 40 DWV-, acrylonitrile/ butadiene/ styrene (ABS) drain, waste and vent pipe and fittings
D2661-68
L-P-322a66
CS270-665
NSF14-65
PVC Schedule 40 DWV, polyvinyl chloride (PVC) drain, waste and vent pipe and fittings
D2265-68
L-P-320a-66
CS272-65
NSF14-65
ABS sewer pipe, acrylonitrile/ buladiene/ styrene (ABS) Schedule 40 pipe and fittings
D2661-68
L-P-322a-66
CS270-65
NSF14-65
Hubless cast-iron soil pipe and fittings
CISP1301
Plastic water service, polyethylene (PE) pipe and fittings
B72.1-67
D1204-68
D2239-68
L-P-00315b-67
CS197-60
CS255-63
PS10-69
PS11-69
PS12-69
Polyethelene (nalgene)
D2104-62T
CS197-60
Polypropylene (fuseal)
D883-64T
D1600-61T
Polybutylene (water pipe)
D3309-74
D2666-73A
Concrete sewer pipe, nonreinforced
C14-67
SS-P-371-a-1956
B. 
Asbestos-cement building sewer pipe. Asbestos-cement building sewer pipe shall be in four-inch, five-inch and six-inch sizes. Classes 1500, 2400 and 3300 shall meet a minimum crushing strength of 1,500 pounds per foot for Class 1500, 2,400 pounds per foot for Class 2400 and 3,300 pounds per foot for Class 3300 tested, as per Section 10 of ASTM C500-63T (Methods of Testing Asbestos-Cement Pipe). Standard lengths shall be five, 6.5, 10 or 13 feet.